AZ AZ764 16 A SPDT MINIATURE POWER RELAY FEATURES • • • • • • • • • Dielectric strength 5000 Vrms Low height: 15.7 mm Epoxy sealed version available 16 Amp switching AC and DC coils Isolation spacing greater than 10 mm Proof tracking index (PTI/CTI) 250 Surpasses requirements of VDE 0631/0700 UL, CUR file E43203; VDE 112904 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) SPST (1 Form A) Ratings Resistive load: Max. switched power: 480 W or 4000 VA Max. switched current: 16 A Max. switched voltage: 300* VDC or 400 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Life Expectancy Mechanical Electrical Minimum operations 3 x 107 1 x 105 at 16 A 240 VAC res. Operate Time (typical) 7 ms at nominal coil voltage Release Time (typical) 4 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Rated Load UL, CUR VDE 16 A at 250 VAC resistive 16 A at 250 VAC Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Material Silver tin oxide Dropout Resistance < 100 milliohms initially Greater than 10% of nominal coil voltage - DC Greater than 15% of nominal coil voltage - AC Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 90°C (194°F) - DC coils -40°C (-40°F) to 75°C (167°F) - AC coils -40°C (-40°F) to 115°C (239°F) Storage COIL Power Vibration 0.062" DA at 10–55 Hz Shock 30 g At Pickup Voltage (typical) 200 mW (DC coil) .422 VA (AC coil) Enclosure P.B.T. polyester, UL-94 ; V0 Max. Continuous Dissipation 1.7 W at 20°C (68°F) ambient Terminals Tinned copper alloy, P. C. Temperature Rise 26°C (47°F) at nominal coil voltage Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 Seconds Weight 14 grams Max. Temperature 115°C (239°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 06/08/05W AZ AZ764 RELAY ORDERING DATA COIL SPECIFICATIONS - DC Coil Nominal Coil VDC 3 ORDER NUMBER* Must Operate VDC 2.1 Max. Continuous VDC 7.6 Coil Resistance ±10% 22 Unsealed Sealed AZ764–1CE–3D AZ764–1CE–3DE 5 3.5 12.7 60 AZ764–1CE–5D AZ764–1CE–5DE 6 4.2 15.3 90 AZ764–1CE–6D AZ764–1CE–6DE AZ764–1CE–9DE 9 6.3 22.9 200 AZ764–1CE–9D 12 8.4 30.6 360 AZ764–1CE–12D AZ764–1CE–12DE 18 12.6 45.9 710 AZ764–1CE–18D AZ764–1CE–18DE 24 16.8 61.2 1,440 AZ764–1CE–24D AZ764–1CE–24DE 36 25.2 92 3,140 AZ764–1CE–36D AZ764–1CE–36DE 48 33.6 122.0 5,700 AZ764–1CE–48D AZ764–1CE–48DE 60 42.0 153.0 7,500 AZ764–1CE–60D AZ764–1CE–60DE 110 77.0 280.0 25,200 AZ764–1CE–110D AZ764–1CE–110DE COIL SPECIFICATIONS - AC Coil Nominal Coil VAC 12 Must Operate VAC 9.0 24 18.0 48 36.0 ORDER NUMBER* Max. Continuous VAC 18.0 Nominal Current mA ±10% 63.0 Coil Resistance ±10% 100 AZ764–1CE–12A AZ764–1CE–-12AE 36.0 31.3 400 AZ764–1CE–24A AZ764–1CE–24AE 72.0 15.6 1550 AZ764–1CE–48A AZ764–1CE–48AE Unsealed Sealed 60 45.0 90.0 12.5 2600 AZ764–1CE–60A AZ764–1CE–60AE 110 82.5 165.0 6.8 8900 AZ764–1CE–110A AZ764–1CE–110AE 115 86.3 172.5 6.5 9600 AZ764–1CE–115A AZ764–1CE–115AE 120 90.0 180.0 6.3 10200 AZ764–1CE–120A AZ764–1CE–120AE 220 165.0 330.0 3.4 35500 AZ764–1CE–220A AZ764–1CE–220AE 230 172.5 345.0 3.3 38500 AZ764–1CE–230A AZ764–1CE–230AE 240 180.0 360.0 3.1 42500 AZ764–1CE–240A AZ764–1CE–240AE * For 1 Form A contacts substitute “A” for “C”. NOTE: 1 Form A contacts are only available for DC coil versions. HARDWARE ORDERING DATA DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER Socket ST484–U1 Retainer ST482–3 MECHANICAL DATA 1.142 [29.0] 0.500 Max. [12.7] Max. PC BOARD LAYOUT HARDWARE VIEWED TOWARDS TERMINALS .197 [5.0] .591 [15.0] .197 [5.0] .618 Max. [15.7] ST484-U1 .500 (12.7) .098 [2.5] * .295 [7.5] * .295 [7.5] .154 [3.9] 6X .020 [0.5] 1.28 (32.5) 1.22 (30.9) .098 [2.5] .354 (9.0) .177 (4.5) MAX .414 (10.5) .125 DIA (0.5) .366 (9.3) 8X ø.050 [ø1.3] RETAINING CLIP 2X ø.024 [ø0.6] * Not used on 1 Form A relay .295 (7.5) .197 (5.0) 1.385 [35.19] WIRING DIAGRAMS .295 [7.5] 6X .035 [0.9] .197 [5.0] .197 [5.0] .591 [15.0] VIEWED TOWARDS TERMINALS 4 5 3 2 4 5 2 .098 [2.5] .197 (5.0) .590 (15) .895 [22.73] .661 [16.79] .059 DIA (1.5) .118 (3.0) 8 7 6 1 8 1 Form C 7 ST482-3 1 1 Form A Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 06/08/05W