TI1 DRV2604LYZFT Drv2604l 2- to 5.2-v haptic driver for lra and erm with internal memory and smart-loop architecture Datasheet

Product
Folder
Sample &
Buy
Tools &
Software
Technical
Documents
Support &
Community
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
DRV2604L 2- to 5.2-V Haptic Driver for LRA and ERM
with Internal Memory and Smart-Loop Architecture
1 Features
•
1
•
•
•
•
•
•
•
•
•
•
Flexible Haptic and Vibration Driver
– LRA (Linear Resonance Actuator)
– ERM (Eccentric Rotating Mass)
I2C-Controlled Digital Playback Engine
– Waveform Sequencer and Trigger
– Real-Time Playback Mode through I2C
– Internal RAM for Customized Waveforms
– I2C Dual-Mode Drive (Open and Closed Loop)
Smart-Loop Architecture (Patent Pending Control
Algorithm)
– Automatic Overdrive and Braking
– Automatic Resonance Tracking and Reporting
(LRA Only)
– Automatic Actuator Diagnostic
– Automatic Level Calibration
– Wide Support for Actuator Models
Immersion TouchSense® 3000 Compatible
Drive Compensation Over Battery Discharge
Wide Voltage Operation (2 V to 5.2 V)
Efficient Differential Switching Output Drive
PWM Input with 0% to 100% Duty-Cycle Control
Range
Hardware Trigger Input
Fast Startup Time
1.8-V Compatible, VDD-Tolerant Digital Interface
The DRV2604L device includes enough integrated
RAM to allow the user to pre-load over 100
customized smart-loop architecture waveforms.
These waveforms can be instantly played back
through I2C or optionally triggered through a
hardware trigger terminal.
Additionally, the real-time playback mode allows the
host processor to bypass the memory playback
engine and play waveforms directly from the host
through I2C.
The smart-loop architecture inside the DRV2604L
device allows simple auto-resonant drive for the LRA
as well as feedback-optimized ERM drive allowing for
automatic overdrive and braking. The smart-loop
architecture creates a simplified input waveform
interface as well as reliable motor control and
consistent motor performance. The DRV2604L device
also features automatic transition to an open-loop
system in the event that an LRA actuator is not
generating a valid back-EMF voltage. When the LRA
generates a valid back-EMF voltage, the DRV2604L
device automatically synchronizes with the LRA. The
DRV2604L also allows for open-loop driving through
the use of internally-generated PWM.
Device Information(1)
PART NUMBER
Mobile Phones
Tablets
3 Description
The DRV2604L device is a low-voltage haptic driver
that provides a closed-loop actuator-control system
for high-quality tactile feedback for ERM and LRA.
This schema helps improve actuator performance in
terms of acceleration consistency, start time, and
brake time and is accessible through a shared I2C
compatible bus or PWM input signal.
BODY SIZE (MAX)
DRV2604L
DSBGA (9)
1.50 mm × 1.50 mm
DRV2604L
VSSOP (10)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
2 Applications
•
•
PACKAGE
VDD
RAM
Supply
correction
SDA
Gate
drive
OUT+
2
I C I/F
SCL
EN
Control and
playback
engine
Back-EMF
detection
M
LRA
or
ERM
IN/TRIG
REG
REG
Gate
drive
OUT±
GND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
5
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
5
5
5
5
7
7
7
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Timing Requirements ................................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
7
Parameter Measurement Information ................ 10
8
Detailed Description ............................................ 11
7.1 Test Setup for Graphs............................................. 10
8.1 Overview ................................................................. 11
8.2 Functional Block Diagram ....................................... 11
8.3
8.4
8.5
8.6
9
Feature Description.................................................
Device Functional Modes........................................
Programming...........................................................
Register Map...........................................................
12
20
23
38
Application and Implementation ........................ 57
9.1 Application Information............................................ 57
9.2 Typical Application .................................................. 58
9.3 Initialization Setup ................................................... 61
10 Power Supply Recommendations ..................... 62
11 Layout................................................................... 63
11.1 Layout Guidelines ................................................. 63
11.2 Layout Example .................................................... 64
12 Device and Documentation Support ................. 65
12.1
12.2
12.3
12.4
12.5
Documentation Support ........................................
Community Resource............................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
65
65
65
65
65
13 Mechanical, Packaging, and Orderable
Information ........................................................... 65
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (September 2014) to Revision D
•
2
Page
Released full version of the data sheet ................................................................................................................................. 1
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
5 Pin Configuration and Functions
YZF Package
9-Pin DSBGA With 0.5-mm Pitch
(Top View)
A
EN
REG
OUT+
B
IN/TRIG
SDA
GND
C
SCL
VDD
OUT±
1
2
3
Pin Functions
PIN
TYPE (1)
DESCRIPTION
NO.
NAME
A1
EN
I
Device enable
A2
REG
O
The REG pin is the 1.8-V regulator output. A 1-µF capacitor is required.
A3
OUT+
O
Positive haptic driver differential output
B1
IN/TRIG
I
Multi-mode Input. I2C selectable as PWM, analog, or trigger. If not used, this pin should
be connected to GND
B2
SDA
I/O
B3
GND
P
Supply ground
C1
SCL
I
I2C clock
C3
OUT–
O
Negative haptic-driver differential output
C2
VDD
P
Supply input (2 to 5.2 V). A 1-µF capacitor is required.
(1)
I2C data
I = input, O = output, I/O = input and output, P = power
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
3
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
DGS Package
10-Pin VSSOP
(Top View)
REG
1
10
SCL
2
9
OUT±
SDA
3
8
GND
IN/TRIG
4
7
OUT+
EN
5
6
VDD/NC
VDD
Pin Functions
PIN
NO.
NAME
TYPE (1)
DESCRIPTION
1
REG
O
The REG pin is the 1.8-V regulator output. A 1-µF capacitor required
2
SCL
I
I2C clock
3
SDA
I/O
I2C data
4
IN/TRIG
I
Multi-mode Input. I2C is selectable as PWM, analog, or trigger. If not used, this pin should
be connected to GND
5
EN
I
Device enable
6
VDD/NC
P
Optional supply input. This pin should be tied to VDD or left floating.
7
OUT+
O
Positive haptic driver differential output
8
GND
P
Supply ground
9
OUT–
O
Negative haptic driver differential output
10
VDD
P
Supply Input (2 V to 5.2 V). A 1-µF capacitor is required.
(1)
4
I = input, O = output, I/O = input and output, P = power
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range, TA = 25°C (unless otherwise noted)
Input voltage
MIN
MAX
UNIT
VDD
–0.3
5.5
V
EN
–0.3
VDD + 0.3
V
SDA
–0.3
VDD + 0.3
V
SCL
–0.3
VDD + 0.3
V
IN/TRIG
–0.3
VDD + 0.3
V
Operating free-air temperature, TA
–40
85
°C
Operating junction temperature, TJ
–40
150
°C
Storage temperature, Tstg
–65
150
°C
6.2 ESD Ratings
VALUE
UNIT
9-PIN DSBGA PACKAGE
V(ESD)
Electrostatic
discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±1000
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (2)
±250
V
10-PIN VSSOP PACKAGE
V(ESD)
Electrostatic
discharge
Human body model (HBM), per
ANSI/ESDA/JEDEC JS-001
OUT+, OUT– pins (3)
±500
Other pins (1)
±1000
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins
(1)
(2)
(3)
(2)
V
±250
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as ±1000
V may actually have higher performance.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Pins listed as ±250 V
may actually have higher performance.
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
VDD
Supply voltage
VDD
2
5.2
V
ƒ(PWM)
PWM input frequency (1)
IN/TRIG Pin
10
250
kHz
ZL
Load impedance (1)
VDD = 5.2 V
8
VIL
Digital low-level input voltage
EN, IN/TRIG, SDA, SCL
VIH
Digital high-level input voltage
EN, IN/TRIG, SDA, SCL
VI(ANA)
Input voltage (analog mode)
IN/TRIG
ƒ(LRA)
(1)
LRA Frequency Range
(1)
Ω
0.5
1.3
V
V
0
1.8
V
125
300
Hz
Ensured by design. Not production tested.
6.4 Thermal Information
DRV2604L
THERMAL METRIC (1)
YZF (DSBGA)
UNIT
(9-PINS)
RθJA
Junction-to-ambient thermal resistance
145.2
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
0.9
°C/W
RθJB
Junction-to-board thermal resistance
105
°C/W
φJT
Junction-to-top characterization parameter
5.1
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
5
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Thermal Information (continued)
DRV2604L
THERMAL METRIC (1)
YZF (DSBGA)
UNIT
(9-PINS)
φJB
6
Junction-to-board characterization parameter
Submit Documentation Feedback
103.3
°C/W
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
6.5 Electrical Characteristics
TA = 25°C, VDD = 3.6 V (unless otherwise noted)
PARAMETER
V(REG)
IIL
IIH
TEST CONDITIONS
MIN
Voltage at the REG pin
Digital low-level input current
Digital high-level input current
TYP
MAX
1.83
UNIT
V
EN, IN/TRIG, SDA, SCL
VDD = 5.2 V , VI = 0 V
1
IN/TRIG, SDA, SCL
VDD = 5.2 V, VI = VDD
1
EN
VDD = 5.2 V, VI = VDD
3.5
0.4
µA
µA
VOL
Digital low-level output voltage
SDAIOL= 4 mA
V
R(EN-GND)
Digital pull-down resistance
EN
VDD = 5.2 V , VI = VDD
2
I(SD)
Shutdown current
V(EN) = 0 V
4
II(standby)
Standby current
V(EN) = 1.8 V, STANDBY = 1
4.1
7
µA
IQ
Quiescent current
V(EN) = 1.8 V, STANDBY = 0, no signal
0.5
0.65
mA
ZI
Input impedance
IN/TRIG to V(CM_ANA)
100
kΩ
V(CM_ANA)
IN/TRIG common-mode voltage
(AC-coupled)
AC_COUPLE = 1
0.9
V
ZO(SD)
Output impedance in shutdown
OUT+ to GND, OUT– to GND
15
kΩ
ZL(th)
Load impedance threshold for
over-current detection
OUT+ to GND, OUT– to GND
4
Ω
I(BAT_AV)
Average battery current during
operation
MΩ
7
µA
Duty cycle = 90%, LRA mode, no load
2.4
3.5
Duty cycle = 90%, ERM mode, no load
2.3
3.5
NOM
MAX
UNIT
400
kHz
mA
6.6 Timing Requirements
TA = 25°C, VDD = 3.6 V (unless otherwise noted)
MIN
ƒ(SCL)
Frequency at the SCL pin with no wait states
tw(H)
Pulse duration, SCL high
tw(L)
Pulse duration, SCL low
tsu(1)
Setup time, SDA to SCL
th(1)
0.6
µs
1.3
µs
100
ns
Hold time, SCL to SDA
10
ns
t(BUF)
Bus free time between stop and start
condition
1.3
µs
tsu(2)
Setup time, SCL to start condition
0.6
µs
th(2)
Hold time, start condition to SCL
0.6
µs
tsu(3)
Setup time, SCL to stop condition
0.6
µs
See Figure 1.
See Figure 2.
6.7 Switching Characteristics
TA = 25°C, VDD = 3.6 V (unless otherwise noted)
PARAMETER
t(start)
ƒO(PWM)
Start-up time
TEST CONDITIONS
MIN
TYP
Time from the GO bit or external trigger
command to output signal
0.7
Time from EN high to output signal
(PWM/Analog Modes)
1.5
PWM Output Frequency
MAX
ms
19.5
20.5
21.5
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
UNIT
kHz
7
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
tw(H)
tw(L)
SCL
tsu(1)
th(1)
SDA
Figure 1. SCL and SDA Timing
SCL
tsu(2)
tsu(3)
th(2)
t(BUF)
SDA
Start Condition
Stop Condition
Figure 2. Timing for Start and Stop Conditions
8
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
6.8 Typical Characteristics
Voltage (2V/div)
IN/TRIG
Acceleration
[OUT+] − [OUT−] (Filtered)
Voltage (2V/div)
IN/TRIG
Acceleration
[OUT+] − [OUT−] (Filtered)
0
40m
80m
VDD = 4.2 V
External edge trigger
120m
Time (s)
160m
200m
ERM closed loop
0
40m
VDD = 4.2 V
External level trigger
Figure 3. ERM Click with and without Braking (RAM)
80m
120m
Time (s)
160m
200m
LRA closed loop
Figure 4. LRA Click With and WIthout Braking (RAM)
Voltage (2V/div)
SDA
Acceleration
[OUT+] − [OUT−] (Filtered)
Voltage (2V/div)
SDA
Acceleration
[OUT+] − [OUT−] (Filtered)
0
200m
VDD = 4.2 V
400m
600m
Time (s)
800m
ERM closed loop
1
0
Internal trigger
200m
VDD = 4.2 V
Figure 5. ERM Click-Bounce (RAM)
400m
600m
Time (s)
ERM closed loop
800m
1
Internal trigger
Figure 6. LRA Transition-Click (RAM)
EN
IN/TRIG
Acceleration
[OUT+] − [OUT−] (Filtered)
Voltage (2V/div)
Voltage (2V/div)
EN
SDA
Acceleration
[OUT+] − [OUT−] (Filtered)
0
40m
VDD = 4.2 V
80m
120m
Time (s)
160m
ERM open loop
200m
RTP Mode
0
40m
VDD = 3.6 V
80m
120m
Time (s)
LRA closed loop
160m
200m
PWM Mode
Figure 8. LRA Click With and Without Braking (PWM)
Figure 7. ERM Buzz (RTP)
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
9
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Typical Characteristics (continued)
100
ERM mode, RL = 10 : + 100 µH, 1.3 V
ERM mode, RL = 25 : + 100 µH, 2 V(RMS)
SDA
ERM Mode
LRA Mode
Voltage (2V/div)
Supply Current (mA)
90
80
70
60
50
0
1m
2m
VDD = 4.2 V
3m
4m
5m
6m
Time (s)
7m
8m
9m
Closed loop
10m
No filter
2
2.4
2.8
3.2
3.6
4
Supply Voltage (V)
4.4
4.8
5.2
D013
Figure 10. Supply Current vs Supply Voltage (Full Vibration)
Figure 9. Startup Latency for ERM and LRA
7 Parameter Measurement Information
7.1 Test Setup for Graphs
To capture the graphs displayed in the Typical Characteristics section, the following first-order RC-filter setup
was used with the exception of the waveform in Figure 9 which was captured without any output filter. This filter
is recommended when viewing output signals on an oscilloscope because output PWM modulation is present in
all modes. Ensure that effective impedance of the filter is not too low because the closed-loop and auto
resonance-tracking features can be affected. Therefore, TI recommends that this exact filter be used for output
measurement. Most oscilloscopes have an input impedance of 1 MΩ on each channel and therefore have an
approximately 1% loss in measured amplitude because of the voltage-divider effect with the filter.
100 k
OUT+
LRA
M
or
ERM
OUT±
470 pF
100 k
Ch1
Ch2
470 pF
Ch1 ± Ch2
(Differential)
Oscilloscope
Figure 11. Test Setup
7.1.1 Default Test Conditions
• VDD = 3.6 V, unless otherwise noted.
• Real actuators (as opposed to modeled actuators) were used as loads for both ERM and LRA modes with
exception of the Supply Voltage vs Supply Current (Full Vibration) waveform in Figure 10, which used passive
RL (resistance in series with an inductance) loads for test repeatability. Real actuators vary widely in supply
currents because of variation in back-EMF voltages. Because real actuators have back EMF, the real supply
current is generally less than what is shown in the waveform because of the reduction in the apparent load
impedance. Therefore, the curve shows the worst-case current.
• All traces are 2 V/div except for the accelerometer traces
• All accelerometer traces are 0.87 g/div except for the LRA Click with and without Braking (PWM) curve in
Figure 8, which is 1.74 g/div.
10
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8 Detailed Description
8.1 Overview
The DRV2604L device is a low-voltage haptic driver that relies on the back-EMF produced by an actuator to
provide a closed-loop system that offers extremely flexible control of LRA and ERM actuators over a shared I2Ccompatible bus or PWM input signal. This schema helps improve actuator performance in terms of acceleration
consistency, start time, and brake time.
The improved smart-loop architecture inside the DRV2604L device provides effortless auto-resonant drive for
LRA, as well as feedback-optimized ERM drive allowing for automatic overdrive and braking. These features
create a simplified input waveform paradigm as well as reliable motor control and consistent motor performance.
The DRV2604L device also features an automatic transition to open-loop operation in the event that an LRA
actuator is not generating a valid back-EMF voltage and automatic synchronization with the LRA when the LRA
is generating a valid back-EMF voltage. The DRV2604L device also allows for open-loop driving by using
internally-generated PWM.
The DRV2604L device includes enough integrated RAM to allow the user to preload over 100 customized
waveforms. The waveforms can be instantly played back through an I2C or can be triggered through a hardware
trigger pin. Additionally, the real-time playback mode allows the host processor to bypass the memory playback
engine and play waveforms directly from the host through the I2C.
The DRV2604L device features a trinary-modulated output stage that provides more efficiency than linear-based
output drivers.
8.2 Functional Block Diagram
VDD
RAM
Supply
correction
SDA
Gate
drive
OUT+
2
I C I/F
SCL
EN
Control and
playback
engine
Back-EMF
detection
M
LRA
or
ERM
IN/TRIG
REG
REG
Gate
drive
OUT±
GND
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
11
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.3 Feature Description
8.3.1 Support for ERM and LRA Actuators
The DRV2604L device supports both ERM and LRA actuators. The ERM_LRA bit in register 0x1A must be
configured to select the type of actuator that the device uses.
8.3.2 Smart-Loop Architecture
The smart-loop architecture is an advanced closed-loop system that optimizes the performance of the actuator
and allows for failure detection. The architecture consists of automatic resonance tracking and reporting (for an
LRA), automatic level calibration, accelerated startup and braking, diagnostics routines, and other proprietary
algorithms.
8.3.2.1 Auto-Resonance Engine for LRA
The DRV2604L auto-resonance engine tracks the resonant frequency of an LRA in real time, effectively locking
onto the resonance frequency after half of a cycle. If the resonant frequency shifts in the middle of a waveform
for any reason, the engine tracks the frequency from cycle to cycle. The auto-resonance engine accomplishes
the tracking by constantly monitoring the back-EMF of the actuator. The auto-resonance engine is not affected by
the auto calibration process, which is only used for level calibration. No calibration is required for the auto
resonance engine. See the Auto-Resonance Engine Programming for the LRA section for auto-resonance engine
programming information.
8.3.2.2 Real-Time Resonance-Frequency Reporting for LRA
The smart-loop architecture makes the resonant frequency of the LRA available through I2C (see the LRA
Resonance Period (Address: 0x22) section). Because frequency reporting occurs in real time, the frequency
must be polled while the DRV2604L device synchronizes with the LRA. The data should not be polled when the
actuator is idle or braking.
8.3.2.3 Automatic Switch to Open-Loop for LRA
In the event that an LRA produces a non-valid back-EMF signal, the DRV2604L device automatically switches to
open-loop operation and continues to deliver energy to the actuator in overdrive mode at a default and
configurable frequency. Use Equation 1 to calculate the default frequency. If the LRA begins to produce a valid
back-EMF signal, the auto-resonance engine automatically takes control and continues to track the resonant
frequency in real time. When synchronized, the mode enjoys all of the benefits that the smart-loop architecture
has to offer.
1
¦(LRA_NO-BEMF) |
u W(DRIVE_TIME[4:0]) ± W(ZC _ DET _ TIME[1:0])
(1)
The DRV2604L device offers an automatic transition to open-loop mode without the re-synchronization option.
The feature is enabled by setting the LRA_AUTO_OPEN_LOOP bit in register 0x1F. The transition to open-loop
mode only occurs when the driver fails to synchronize with the LRA. The AUTO_OL_CNT[1:0] bit in register 0x1F
can be adjusted to set the amount of non-synchronized cycles allowed before the transition to the open-loop
mode. Use Equation 2 to calculate the open-loop frequency. The open-loop mode does not receive benefits from
the smart-loop architecture, such as automatic overdrive and braking.
1
¦(LRA_OL)
OL_LRA_PERIOD[6:0] × 98.49 × 10 ±
(2)
8.3.2.4 Automatic Overdrive and Braking
A key feature of the DRV2604L is the smart-loop architecture which employs actuator feedback control for both
ERMs and LRAs. The feedback control desensitizes the input waveform from the motor-response behavior by
providing automatic overdrive and automatic braking.
12
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Feature Description (continued)
An open-loop haptic system typically drives an overdrive voltage at startup that is higher than the steady-state
rated voltage of the actuator to decrease the startup latency of the actuator. Likewise, a braking algorithm must
be employed for effective braking. When using an open-loop driver, these behaviors must be contained in the
input waveform data. Figure 12 shows how two different ERMs with different startup behaviors (Motor A and
Motor B) can both be driven optimally by the smart-loop architecture with a simple input for both motors. The
smart-loop architecture works equally well for LRAs with a combination of feedback control and an autoresonance engine.
Ideal Open-Loop Waveform for Motor A
Ideal Open-Loop Waveform for Motor B
Same simple input for
both motors
Input and output
Feedback provides
optimum output drive
Accleration
Output with feedback
Figure 12. Waveform Simplification With Smart Loop
8.3.2.4.1 Startup Boost
To reduce the actuator start-time performance, the DRV2604L device has an overdrive boost feature that applies
higher loop gain to transient response of the actuator. The STARTUP_BOOST bit enables the feature.
8.3.2.4.2 Brake Factor
To reduce the actuator brake-time performance, the DRV2604L device provides a means to increase the gain
ratio between braking and driving gain. Higher feedback-gain ratios reduce the brake time, however, the gain
ratios also reduce the stability of the closed-loop system. The FB_BRAKE_FACTOR[2:0] bits can be adjusted to
set the brake factor.
8.3.2.4.3 Brake Stabilizer
To improve brake stability at high brake-factor gain ratios, the DRV2604L device has a brake-stabilizer
mechanism that automatically reduces the loop gain when the braking is near completion. The
BRAKE_STABILIZER bit enables the feature.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
13
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Feature Description (continued)
8.3.2.5 Automatic Level Calibration
The smart-loop architecture uses actuator feedback by monitoring the back-EMF behavior of the actuator. The
level of back-EMF voltage can vary across actuator manufacturers because of the specific actuator construction.
Auto calibration compensates for the variation and also performs scaling for the desired actuator according to the
specified rated voltage and overdrive clamp-register settings. When auto calibration is performed, a 100% signal
level at any of the DRV2604L input interfaces supplies the rated voltage to the actuator at steady-state. The
feedback allows the output level to increase above the rated voltage level for automatic overdrive and braking,
but without allowing the output level to exceed the programmable overdrive clamp voltage.
In the event where the automatic level-calibration routine fails, the DIAG_RESULT bit in register 0x00 is asserted
to flag the problem. Calibration failures are typically fixed by adjusting the registers associated with the automatic
level-calibration routine or, for LRA actuators, the registers associated with the automatic-resonance detection
engine. See the Device and Documentation Support section for automatic-level calibration programming.
8.3.2.5.1 Automatic Compensation for Resistive Losses
The DRV2604L device automatically compensates for resistive losses in the driver. During the automatic levelcalibration routine, the impedance of the actuator is checked and the compensation factor is determined and
stored in the A_CAL_COMP[7:0] bit.
8.3.2.5.2 Automatic Back-EMF Normalization
The DRV2604L device automatically compensates for differences in back-EMF magnitude between actuators.
The compensation factor is determined during the automatic level-calibration routine and the factor is stored in
the A_CAL_BEMF[7:0] bit.
8.3.2.5.3 Calibration Time Adjustment
The duration of the automatic level-calibration routine has an impact on accuracy. The impact is highly
dependent on the start-time characteristic of the actuator. The auto-calibration routine expects the actuator to
have reached a steady acceleration before the calibration factors are calculated. Because the start-time
characteristic can be different for each actuator, the AUTO_CAL_TIME[1:0] bit can change the duration of the
automatic level-calibration routine to optimize calibration performance.
8.3.2.5.4 Loop-Gain Control
The DRV2604L device allows the user to control how fast the driver attempts to match the back-EMF (and thus
motor velocity) and the input signal level. Higher loop-gain (or faster settling) options result in less-stable
operation than lower loop gain (or slower settling). The LOOP_GAIN[1:0] bit controls the loop gain.
8.3.2.5.5 Back-EMF Gain Control
The BEMF_GAIN[1:0] bit sets the analog gain for the back-EMF amplifier. The auto-calibration routine
automatically populates the bit with the most appropriate value for the actuator.
Modifying the SAMPLE_TIME[1:0] bit also adjusts the back-EMF gain. The higher the sample time, the higher
the gain.
By default, the back-EMF is sampled once during a period. In the event that a twice per-period sampling is
desired, assert the LRA_DRIVE_MODE bit.
8.3.2.6 Actuator Diagnostics
The DRV2604L device is capable of determining whether the actuator is not present (open) or shorted. If a fault
is detected during the diagnostic process, the DIAG_RESULT bit is asserted.
8.3.2.7 Automatic Re-Synchronization
For the LRA, the DRV2604L device features an automatic re-synchronization mode which automatically pushes
the actuator in the correct direction when a waveform begins playing while the actuator is moving. If the actuator
is at rest when the waveform begins, the DRV2604L device drives in the default direction.
14
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Feature Description (continued)
8.3.3 Open-Loop Operation for LRA
In the event that open-loop operation is desired (such as for off-resonance driving) the DRV2604L device
includes an open-loop LRA drive mode that is available through the PWM input or through the digital interface.
When using the PWM input in open-loop mode, the DRV2604L device employs a fixed divider that observes the
PWM signal and commutates the output drive signal at the PWM frequency divided by 128. To accomplish LRA
drive, the host should drive the PWM frequency at 128 times the desired operating frequency.
When activated, the digital open-loop mode is available for pre-stored waveforms as well as for RTP mode. The
OL_LRA_PERIOD bit in register 0x20 programs the operating frequency, which is derived from the PWM output
frequency, ƒO(PWM). Use Equation 1 to calculate the driving frequency. The open-loop mode does not receive the
benefits of the smart-loop architecture.
8.3.4 Open-Loop Operation for ERM
The DRV2604L device offers ERM open-loop operation through the PWM input. The output voltage is based on
the duty cycle of the provided PWM signal, where the OD_CLAMP[7:0] bit in register 0x17 sets the full-scale
amplitude. For details see the Rated Voltage Programming section.
8.3.5 Flexible Front-End Interface
The DRV2604L device offers multiple ways to launch and control haptic effects. The MODE[2:0] bit in register
0x01 is used to select the interface mode.
8.3.5.1 PWM Interface
When the DRV2604L device is in PWM interface mode, the device accepts PWM data at the IN/TRIG pin. The
DRV2604L device drives the actuator continuously in PWM interface mode until the user sets the device to
standby mode or to enter another interface mode. In standby mode, the strength of vibration is determined by the
duty cycle.
For the LRA, the DRV2604L device automatically tracks the resonance frequency unless the LRA_OPEN_LOOP
bit in register 0x1D is set. If the LRA_OPEN_LOOP bit is set, the LRA is driven according to the frequency of the
PWM input signal. Specifically, the driving frequency is the PWM frequency divided by 128.
8.3.5.2 Internal Memory Interface
The DRV2604LL device is designed with 2 kB of integrated RAM for waveform storage used by the playback
engine. The data is stored in an efficient way (voltage-time pairs) to maximize the number of waveforms that can
be carried. The playback engine also has the ability to generate smooth ramps (up or down) by relying on the
start-waveform and end-waveform points and by using linear interpolation techniques.
Storing waveforms on the DRV2604LL device instead of the host processor has several advantages including:
• Offloading processing requirements, such as PWM generation, from the host processor or micro-controller
• Improving latency by storing the waveforms on the DRV2604LL device and only requiring a trigger signal
• Reducing I2C traffic by eliminating the requirement to transfer waveform data
8.3.5.2.1 Waveform Sequencer
The waveform sequencer queues waveform identifiers for playback. Eight sequence registers queue up to eight
waveforms for sequential playback. A waveform identifier is an integer value referring to the index position of a
waveform in the RAM library. Playback begins at register address 0x04 when the user asserts the GO bit
(register 0x0C). When playback of that waveform ends, the waveform sequencer plays the waveform identifier
held in register 0x05 if the next waveform is non-zero. The waveform sequencer continues in this way until it
reaches an identifier value of zero or until all eight identifiers are played (register addresses 0x04 through 0x0B),
whichever scenario is reached first.
The waveform identifier range is 1 to 127. The MSB of each sequence register can implement a delay between
sequence waveforms. When the MSB is high, bits [6:0] indicate the length of the wait time. The wait time for that
step then becomes WAV_FRM_SEQ[6:0] × 10 ms.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
15
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Feature Description (continued)
8.3.5.2.2 Library Parameterization
The RAM waveforms are augmented by the time offset registers (registers 0x0D to 0x10). The augmentation
occurs only for the RAM waveforms and not for the other interfaces (such as PWM and RTP). The purpose of
the functionality is to add time stretching (or time shrinking) to the waveform. This functionality is useful for
customizing the entire library of waveforms for a specific actuator rise time and fall time.
The time parameters that can be stretched or shrunk include:
ODT
Overdrive time
SPT
Sustain positive time
SNT
Sustain Negative Time
BRT
Brake Time
The time values are additive offsets and are 8-bit signed values. The default offset of the time values is 0.
Positive values add and negative values subtract from the time value of the effect that is currently played. The
most positive value in the waveform is automatically interpreted as the overdrive time, and the most negative
value in the waveform is automatically interpreted as the brake time. The time-offset parameters are applied to
both voltage-time pairs and linear ramps. For linear ramps, linear interpolation is stretched (or shrunk) over the
two operative points for the period (see Equation 3).
t + t(ofs)
where
•
t(ofs) is the time offset
(3)
Changing the playback interval can also manipulate the waveforms stored in memory. Each waveform in memory
has a granularity of 5 ms. If the user desires greater granularity, a 1-ms playback interval can be obtained by
asserting the PLAYBACK_INTERVAL bit in register 0x1F.
8.3.5.3 Real-Time Playback (RTP) Interface
The real-time playback mode is a simple, single 8-bit register interface that holds an amplitude value. When realtime playback is enabled, the real-time playback register is sent directly to the playback engine. The amplitude
value is played until the user sends the device to standby mode or removes the device from RTP mode. The
RTP mode operates exactly like the PWM mode except that the user enters a register value over the I2C rather
than a duty cycle through the input pin. Therefore, any API (application-programming interface) designed for use
with a PWM generator in the host processor can write the data values over the I2C rather than writing the data
values to the host timer. This ability frees a timer in the host while retaining compatibility with the original
software.
For the LRA, the DRV2604L device automatically tracks the resonance frequency unless the LRA_OPEN_LOOP
bit is set (in register 0x1D). If the LRA_OPEN_LOOP bit is set, the LRA is driven according to the open-loop
frequency set in the OL_LRA_PERIOD[6:0] bit in register 0x20.
8.3.5.4 Analog Input Interface
When the DRV2604L device is in analog-input interface mode, the device accepts an analog voltage at the
IN/TRIG pin. The DRV2604L device drives the actuator continuously in analog-input interface mode until the user
sets the device to standby mode or to enter another interface mode. The reference voltage in standby mode is
1.8 V. Therefore, the 1.8-V reference voltage is interpreted as a 100% input value. A reference voltage of 0.9 V
is interpreted as a 50% input value and a reference voltage of 0 V is interpreted as a 0% input value. The input
value in standby mode is analogous to the duty-cycle percentage in PWM mode.
For the LRA, the DRV2604L automatically tracks the resonance frequency unless the LRA_OPEN_LOOP bit is
set (in register 0x1D). If the LRA_OPEN_LOOP bit is set, the LRA is driven according to the open-loop frequency
set in OL_LRA_PERIOD[6:0] bit in register 0x20.
16
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Feature Description (continued)
8.3.5.5 Input Trigger Option
The DRV2604L device includes continuous haptic modes (such as PWM and RTP mode) as well as triggered
modes (such as the internal memory interface). The haptic effects in the continuous haptic modes begin as soon
as the device enters the mode and stop when the device goes into standby mode or exits the continuous haptic
mode. For the triggered mode, the DRV2604L device has a variety of trigger options that are explained in this
section.
In the continuous haptic modes, the IN/TRIG pin provides external trigger control of the GO bit, which allows
GPIO control to fire RAM waveforms. The external trigger control can provide improved latencies in systems
where a significant delay exists between the desired effect time and the time a GO command can be sent over
the I2C interface.
NOTE
The triggered effect must already be selected to take advantage of the lower latency. This
option works best for accelerating a pre-queued high-priority effect (such as a button
press) or for the repeated firing of the same effect (such as scrolling).
8.3.5.5.1 I2C Trigger
Setting the GO bit (in register 0x0C) launches the waveform. The user can cancel the launching of the waveform
by clearing the GO bit.
8.3.5.5.2 Edge Trigger
A low-to-high transition on the IN/TRIG pin sets the GO bit. The playback sequence indicated in the waveform
sequencer plays as normal. The user can cancel the transaction by clearing the GO bit. An additional low-to-high
transition while the GO bit is high also cancels the transaction which clears and resets the GO bit. Clearing the
trigger pin (high-to-low transition) does nothing, therefore the user can send a short pulse without knowing how
long the waveform is. The pulse width should be at least 1 µs to ensure detection.
Edge Trigger
Haptic Waveform
Edge Trigger
Cancellation
Haptic Waveform
Figure 13. Edge Trigger Mode
8.3.5.5.3 Level Trigger
The actions of the GO bit directly follow the IN/TRIG pin. When the IN/TRIG pin is high, the GO bit is high. When
the IN/TRIG pin goes low, the GO bit clears. Therefore, a falling edge cancels the transaction. The level trigger
can implement a GPIO-controlled buzz on-off controller if an appropriately long waveform is selected. The user
must hold the IN/TRIG high for the entire duration of the waveform to complete the effect.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
17
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Feature Description (continued)
Level Trigger
Haptic Waveform
Level Trigger
Cancellation
Haptic Waveform
Figure 14. Level Trigger Mode
8.3.5.6 Noise Gate Control
When an actuator is driven with an analog or PWM signal, noise in the line can cause the actuator to vibrate
unintentionally. For that reason, the DRV2604L device features a noise gate that filters out any voltage smaller
than a particular threshold. The NG_THRESH[1:0] bit in register 0x1D controls the threshold.
8.3.6 Edge Rate Control
The DRV2604L output driver implements edge rate control (ERC). The ERC ensures that the rise and fall
characteristics of the output drivers do not emit levels of radiation that could interfere with other circuitry common
in mobile and portable platforms. Because of ERC most system do not require external output filters, capacitors,
or ferrite beads.
8.3.7 Constant Vibration Strength
The DRV2604L PWM input uses a digital level-shifter. Therefore, as long as the input voltage meets the VIH and
VIL levels, the vibration strength remains the same even if the digital levels vary. The DRV2604L device also
features power-supply feedback. If the supply voltage drifts over time (because of battery discharge, for
example), the vibration strength remains the same as long as enough supply voltage is available to sustain the
required output voltage.
8.3.8 Battery Voltage Reporting
During playback, the DRV2604L device provides real-time voltage measurement of the VDD pin. The VBAT[7:0]
bit located in register 0x21 provides this information.
8.3.9 One-Time Programmable (OTP) Memory for Configuration
The DRV2604L device contains nonvolatile, on-chip, OTP memory for specific configuration parameters. When
written, the DRV2604L device retains the device settings in registers 0x16 through 0x1A including after power
cycling. This retention allows the user to account for small variations in actuator manufacturing from unit to unit
as well as to shorten the device-initialization process for device-specific parameters such as actuator type,
actuator-rated voltage, and other parameters. An additional benefit of OTP is that the DRV2604L memory can be
customized at the device-test level without driving changes in the device software.
8.3.10 Low-Power Standby
Setting the device to standby reduces the idle power consumption without resetting the registers. In Low-Power
Standby mode, the DRV2604L device features a fast turnon time when it is requested to play a waveform.
18
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Feature Description (continued)
8.3.11 I2C Watchdog Timer
If an I2C stops unexpectedly, the possibility exists for the I2C protocol to remain in a hanged state. To allow for
the recovery of the communication without having to power cycle the device, the DRV2604L device includes an
automatic watchdog timer that resets the I2C protocol without user intervention after 4.33 ms. This behavior
happens in all conditions except in standby mode. If the I2C stops unexpectedly during standby mode, the only
way to recover communication is by power-cycling the device.
8.3.12 Device Protection
8.3.12.1 Thermal Protection
The DRV2604L device has thermal protection that causes the device to shut down if it becomes too hot. In the
event where the thermal protection kicks in, the DRV2604L device asserts a flag (bit OVER_TEMP in register
0x00) to notify the host processor.
8.3.12.2 Overcurrent Protection of the Actuator
If the impedance at the output pin of the DRV2604L device is too low, the device latches the over-current flag
(OC_DETECT bit in register 0x00) and shuts down. The device periodically monitors the status of the short and
remains in this condition until the short is removed. When the short is removed, the DRV2604L device restarts in
the default state.
8.3.12.3 Overcurrent Protection of the Regulator
The DRV2604L device has an internal regulator that powers a portion of the system. If a short occurs at the
output of the REG pin, an internal overcurrent protection circuit is enabled and limits the current.
During a REG short, the device is not functional. When the short is removed, the DRV2604L device automatically
resets to default conditions.
8.3.12.4 Brownout Protection
The DRV2604L device has on-chip brownout protection. When activated, a reset signal is issued that returns the
DRV2604L device to the initial default state. If the regulator voltage V(REG) goes below the brownout protection
threshold (V(BOT)) the DRV2604L device automatically shuts down. When V(REG) returns to the typical output
voltage (1.8 V) the DRV2604L device returns to the initial device state. The brownout protection threshold
(V(BOT)) is typically at 0.84 V.
The previously described behavior has one exception. The brownout circuit is designed to tolerate fast brownout
conditions as shown by Case 1 in Figure 15. If the VDD ramp-up rate is slower than 3.6 kV/s, then the device can
fall into an unknown state. In such a situation, to return to the initial default state the device must be powercycled with a VDD ramp-up rate that is faster than 3.6 kV/s.
Case 1
Case 3
Case 2
Case 4
VDD
VDD
Return to
default
state
Unknown
state
Return to
default
state
Unknown
state
2V
1.8 V
REG
V(BOT)
0V
Time
Slew rate > 3.6 kV/s
Slew rate < 3.6 kV/s
Slew rate < 3.6 kV/s
Slew rate > 3.6 kV/s
Figure 15. Brownout Behavior
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
19
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.4 Device Functional Modes
8.4.1 Power States
The DRV2604L device has three different power states which allow for different power-consumption levels and
functions. Figure 16 shows the transition in to and out of each state.
EN = 0
EN = 1
Shutdown
Standby
STANDBY = 0
EN = 0
STANDBY = 1
Active
DEV_RESET = 1
Figure 16. Power-State Transition Diagram
8.4.1.1 Operation With VDD < 2 V (Minimum VDD)
Operating the device with a VDD value below 2 V is not recommended.
8.4.1.2 Operation With VDD > 5.5 V (Absolute Maximum VDD)
The DRV2604L device is designed to operate at up to 5.2 V, with an absolute maximum voltage of 5.5 V. If
exposed to voltages above 5.5 V, the device can suffer permanent damage.
8.4.1.3 Operation With EN Control
The EN pin of the DRV2604L device gates the active operation. When the EN pin is logic high, the DRV2604L
device is active. When the EN pin is logic low, the device enters the shutdown state, which is the lowest power
state of the device. The device registers are not reset. The EN pin operation is particularly useful for constantsource PWM and analog input modes to maintain compatibility with non-I2C device signaling. The EN pin must
be high to write I2C device registers. However, if the EN pin is low the DRV2604L device can still acknowledge
(ACK) during an I2C transaction, however, no read or write is possible. To completely reset the device to the
powerup state, set the DEV_RESET bit in register 0x01.
8.4.1.4 Operation With STANDBY Control
The STANDBY bit in register 0x01 forces the device in an out of the standby state. The STANDBY bit is asserted
by default. When the STANDBY bit is asserted, the DRV2604L device goes into a low-power state. In the
standby state the device retains register values and the ability to have I2C communication. The properties of the
standby state also feature a fast turn, wake up, and play, on-time. Asserting the STANDBY bit has an immediate
effect. For example, if a waveform is played, it immediately stops when the STANDBY bit is asserted.
Clear the STANDBY bit to exit the standby state (and go to the ready state).
8.4.1.5 Operation With DEV_RESET Control
The DEV_RESET bit in register 0x01 performs the equivalent of power cycling the device. Any playback
operations are immediately interrupted, and all registers are reset to the default values. The Dev_Reset bit
automatically-clears after the reset operation is complete.
20
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Device Functional Modes (continued)
8.4.1.6 Operation in the Active State
In the active state, the DRV2604L device has I2C communication and is capable of playing waveforms, running
calibration, and running diagnostics. These operations are referred to as processes. Figure 17 shows the flow of
starting, or firing, a process. Notice that the GO signal fires the processes. Note that the GO signal is not the
same as the GO bit. Figure 18 shows a diagram of the GO-signal behavior.
Change
Modes
Ready
GO Signal = 1
Process
Done
GO Signal = 1
Optional
Run
Process
Check for
Output
Shorts
No Short
Wait 1 s
Short Found
Short Found
Note:
If an output short is present before a waveform is played, changing modes (with the MODE[2:0] bit in register 0x01) is
required to resume normal playback.
Figure 17. Diagram of Active States
8.4.2 Changing Modes of Operation
The DRV2604L has multiple modes for playing waveforms, as well as a calibration mode and a diagnostic mode.
Table 1 lists the available modes.
Table 1. Mode Selection Table
MODE
MODE[2:0]
N_PWM_ANALOG
Internal trigger mode
0
X
External Trigger mode (edge)
1
X
External trigger mode (level)
2
X
Analog input mode
3
0
PWM mode
3
1
RTP mode
5
X
Diagnostics mode
6
X
Calibration mode
7
X
8.4.3 Operation of the GO Bit
The GO bit is the primary way to assert the GO signal, which fires processes in the DRV2604L device. The
primary purpose of the GO bit is to fire the playback of the waveform identifiers in the waveform sequencer
(registers 0x04 to 0x0B). However, The GO bit can also fire the calibration or diagnostics processes.
When using the GO bit to play waveforms in internal trigger mode, the GO bit is asserted by writing 0x01 to
register 0x0C. In this case, the GO bit can be thought of as a software trigger for haptic waveforms. The GO bit
remains high until the playback of the haptic waveform sequence is complete. Clearing the GO bit during
waveform playback cancels the waveform sequence. The GO bit can also be asserted by the external trigger
when in external trigger mode. The GO bit in register 0x0C mirrors the state of the external trigger.
Setting RTP mode or PWM mode also sets the GO bit. However, setting the GO bit in this way has no impact on
the GO bit located in register 0x0C.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
21
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Also accessible
2
(R/W) through I C
MODE[2:0] = 1 (External trigger ² edge)
MODE[2:0] = 2 (External trigger ² level)
GO Bit
IN/TRIG (Trigger)
GO Bit
MODE[2:0] = 3 (PWM and analog input)
GO Signal
MODE[2:0] = 5 (RTP mode)
Figure 18. GO-Signal Logic
8.4.4 Operation During Exceptional Conditions
This section lists different exceptional conditions and the ways that the DRV2604L device operates during these
conditions. This section also describes how the device goes into and out of these states.
8.4.4.1 Operation With No Actuator Attached
In LRA closed-loop mode, if a waveform is played without an actuator connected to the OUT+ and OUT– pins,
the output pins toggle. However, the toggling frequency is not predictable. In LRA open-loop mode, the output
pins toggle at the specified open-loop frequency.
8.4.4.2 Operation With a Non-Moving Actuator Attached
The model of a non-moving actuator can be simplified as a resistor. If a resistor (with similar loading as an LRA,
such as 25 O) is connected across the OUT+ and OUT– pins, and the DRV2604L device is in LRA closed-loop
mode, the output pins toggle at a default frequency calculated with Equation 1. In LRA open-loop mode the
output pins toggle at the specified open-loop frequency.
8.4.4.3 Operation With a Short at REG Pin
If the REG pin is shorted to GND, the device automatically shuts down and an overcurrent-protection circuit is
enabled and clamps the maximum current supplied by the regulator. When the short is removed, the device
starts in the default condition.
8.4.4.4 Operation With a Short at OUT+, OUT–, or Both
If any of the output pins (OUT+ or OUT–) is shorted to VDD, GND, or to each other while the device is playing a
waveform, the OC_DETECT bit is asserted and remains asserted until the short is removed. A current-protection
circuit automatically enables to shutdown the current through the short.
If the driver is playing a waveform the DRV2604L device checks for shorts in the output through either a hapticplayback, auto-calibration, or diagnostics process. If the short occurs when the device is idle, the short is not
detected until the device attempts to run a waveform.
22
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.5 Programming
8.5.1 Auto-Resonance Engine Programming for the LRA
8.5.1.1 Drive-Time Programming
The resonance frequency of each LRA actuator varies based on many factors and is generally dominated by
mechanical properties. The auto-resonance engine-tracking system is optimized by providing information about
the resonance frequency of the actuator. The DRIVE_TIME[4:0] bit is used as an initial guess for the half-period
of the LRA. The drive time is automatically and quickly adjusted for optimum drive. For example, if the LRA has a
resonance frequency of 200 Hz, then the drive time should be set to 2.5 ms.
For ERM actuators, the DRIVE_TIME[4:0] bit controls the rate for back-EMF sampling. Lower drive times imply
higher back-EMF sampling frequencies which cause higher peak-to-average ratios in the output signal, and
requires more supply headroom. Higher drive times imply lower back-EMF sampling frequencies which cause the
feedback to react at a slower rate.
8.5.1.2 Current-Dissipation Time Programming
To sense the back-EMF of the actuator, the DRV2604L device goes into high impedance mode. However, before
the device enters high impedance mode, the device must dissipate the current in the actuator. The DRV2604L
device controls the time allocated for dissipation-current through the IDISS_TIME[3:0] bit.
8.5.1.3 Blanking Time Programming
After the current in the actuator dissipates, the DRV2604L device waits for a blanking time of the signal to settle
before the back-EMF analog-to-digital (AD) conversion converts. The BLANKING_TIME[3:0] bit controls this time.
8.5.1.4 Zero-Crossing Detect-Time Programming
When the blanking time expires, the back-EMF AD monitors for zero crossings. The ZC_DET_TIME[1:0] bit
controls the minimum time allowed for detecting zero crossings.
8.5.2 Automatic-Level Calibration Programming
8.5.2.1 Rated Voltage Programming
The rated voltage is the driving voltage that the driver will output during steady state. However, in closed-loop
drive mode, temporarily having an output voltage that is higher than the rated voltage is possible. See the
Overdrive Voltage-Clamp Programming section for details.
The RATED_VOLTAGE[7:0] bit in register 0x16 sets the rated voltage for the closed-loop drive modes. For the
ERM, Equation 4 calculates the average steady-state voltage when a full-scale input signal is provided. For the
LRA, Equation 5 calculates the root-mean-square (RMS) voltage when driven to steady state with a full-scale
input signal.
V(ERM-CL_AV) = 21.18 × 10± RATED_VOLTAGE[7:0]
V(LRA-CL_RMS) =
20.58 × 10
±
±
(4)
× RATED_VOLTAGE[7:0]
î W(SAMPLE_TIME)
u
±6
î ¦(LRA)
(5)
In open-loop mode, the RATED_VOLTAGE[7:0] bit is ignored. Instead, the OD_CLAMP[7:0] bit (in register 0x17)
is used to set the rated voltage for the open-loop drive modes. For the ERM, Equation 6 calculates the rated
voltage with a full-scale input signal. For the LRA, Equation 7 calculates the RMS voltage with a full-scale input
signal.
V(ERM-OL_AV) = 21.59 × 10 ± OD_CLAMP[7:0]
9(LRA-OL_RMS)
î
±
î 2'B&/$03>
(6)
@î
± ¦(LRA) î
î
±
(7)
The auto-calibration routine uses the RATED_VOLTAGE[7:0] and OD_CLAMP[7:0] bits as inputs and therefore
these registers must be written before calibration is performed. Any modification of this register value should be
followed by calibration to appropriately set A_CAL_BEMF[7:0].
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
23
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
8.5.2.2 Overdrive Voltage-Clamp Programming
During closed-loop operation, the actuator feedback allows the output voltage go above the rated voltage during
the automatic overdrive and automatic braking periods. The OD_CLAMP[7:0] bit (in Register 0x17) sets a clamp
so that the automatic overdrive is bounded. The OD_CLAMP[7:0] bit also serves as the full-scale reference
voltage for open-loop operation. The OD_CLAMP[7:0] bit always represents the maximum peak voltage that is
allowed, regardless of the mode.
NOTE
If the supply voltage (VDD) is less than the overdrive clamp voltage, the output driver is
unable to reach the clamp voltage value because the output voltage cannot exceed the
supply voltage. If the rated voltage exceeds the overdrive clamp voltage, the overdrive
clamp voltage has priority over the rated voltage.
In ERM mode, use Equation 8 to calculate the allowed maximum voltage. In LRA mode, use Equation 9 to
calculate the maximum peak voltage.
î ± î 2'B&/$03> @ î W(DRIVE_TIME) ±
î ±
V(ERM _ clamp) =
t(DRIVE_TIME) t(IDISS_TIME) t(BLANKING_TIME)
(8)
V(LRA_clamp) = 21.22 × 10± × OD _ CLAMP[7:0]
(9)
8.5.3 I2C Interface
8.5.3.1 General I2C Operation
The I2C bus employs two signals, SDA (data) and SCL (clock), to communicate between integrated circuits in a
system. The bus transfers data serially, one bit at a time. The 8-bit address and data bytes are transferred with
the most-significant bit (MSB) first. In addition, each byte transferred on the bus is acknowledged by the receiving
device with an acknowledge bit. Each transfer operation begins with the master device driving a start condition
on the bus and ends with the master device driving a stop condition on the bus. The bus uses transitions on the
data pin (SDA) while the clock is at logic high to indicate start and stop conditions. A high-to-low transition on the
SDA signal indicates a start, and a low-to-high transition indicates a stop. Normal data-bit transitions must occur
within the low time of the clock period. Figure 19 shows a typical sequence. The master device generates the 7bit slave address and the read-write (R/W) bit to start communication with a slave device. The master device
then waits for an acknowledge condition. The slave device holds the SDA signal low during the acknowledge
clock period to indicate acknowledgment. When this acknowledgment occurs, the master transmits the next byte
of the sequence. Each device is addressed by a unique 7-bit slave address plus a R/W bit (1 byte). All
compatible devices share the same signals through a bidirectional bus using a wired-AND connection.
The number of bytes that can be transmitted between start and stop conditions is not limited. When the last word
transfers, the master generates a stop condition to release the bus. Figure 19 shows a generic data-transfer
sequence.
Use external pullup resistors for the SDA and SCL signals to set the logic-high level for the bus. Pullup resistors
with values between 660 Ω and 4.7 kΩ are recommended. Do not allow the SDA and SCL voltages to exceed
the DRV2604L supply voltage, VDD.
NOTE
The DRV2604L slave address is 0x5A (7-bit), or 1011010 in binary.
24
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
7-bit slave address
R/W A
b7 b6 b5 b4 b3 b2 b 1 b 0
8-bit register address (N)
b7 b6 b5 b4 b3 b2 b1 b0
A
8-bit register data for address
(N)
b7 b6 b5 b4 b3 b2 b1 b0
A
8-bit register data for address
(N)
A
b7 b6 b5 b4 b3 b2 b1 b0
Start
Stop
Figure 19. Typical I2C Sequence
The DRV2604L device operates as an I2C-slave 1.8-V logic thresholds, but can operate up to the VDD voltage.
The device address is 0x5A (7-bit), or 1011010 in binary which is equivalent to 0xB4 (8-bit) for writing and 0xB5
(8-bit) for reading.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
25
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
8.5.3.2 Single-Byte and Multiple-Byte Transfers
The serial control interface supports both single-byte and multiple-byte R/W operations for all registers.
During multiple-byte read operations, the DRV2604L device responds with data one byte at a time and beginning
at the signed register. The device responds as long as the master device continues to respond with
acknowledges.
The DRV2604L supports sequential I2C addressing. For write transactions, a sequential I2C write transaction has
taken place if a register is issued followed by data for that register as well as the remaining registers that follow.
For I2C sequential-write transactions, the register issued then serves as the starting point and the amount of data
transmitted subsequently before a stop or start is transmitted determines how many registers are written.
8.5.3.3 Single-Byte Write
As shown in Figure 20, a single-byte data-write transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read-write bit. The read-write bit determines the direction of
the data transfer. For a write-data transfer, the read-write bit must be set to 0. After receiving the correct I2C
device address and the read-write bit, the DRV2604L responds with an acknowledge bit. Next, the master
transmits the register byte corresponding to the DRV2604L internal-memory address that is accessed. After
receiving the register byte, the device responds again with an acknowledge bit. Finally, the master device
transmits a stop condition to complete the single-byte data-write transfer.
Acknowledge
A6
A5
A4
A3
A2
A1
A0
ACK A7
W
Acknowledge
A6
2
Start
condition
A5
A4
A3
A2
A0
Acknowledge
A1 ACK D7
D6
D4
D3
D2
D1
D0 ACK
Stop
condition
Data byte
Subaddress
I C device address
and R/W bit
D5
Figure 20. Single-Byte Write Transfer
8.5.3.4 Multiple-Byte Write and Incremental Multiple-Byte Write
A multiple-byte data write transfer is identical to a single-byte data write transfer except that multiple data bytes
are transmitted by the master device to the DRV2604L device as shown in Figure 21. After receiving each data
byte, the DRV2604L device responds with an acknowledge bit.
Acknowledge
A1
Start
condition
A0
A1
A0
W
ACK
2
I C device address
and R/W bit
Acknowledge
A7
A6
A1
Subaddress
A0 ACK D7
D6
D1
Acknowledge
Acknowledge
Acknowledge
D0 ACK D7
D0 ACK D7
D0 ACK
First data byte
Other data bytes
Last data byte
Stop
condition
Figure 21. Multiple-Byte Write Transfer
8.5.3.5 Single-Byte Read
Figure 22 shows that a single-byte data-read transfer begins with the master device transmitting a start condition
followed by the I2C device address and the read-write bit. For the data-read transfer, both a write followed by a
read actually occur. Initially, a write occurs to transfer the address byte of the internal memory address to be
read. As a result, the read-write bit is set to 0.
After receiving the DRV2604L address and the read-write bit, the DRV2604L device responds with an
acknowledge bit. The master then sends the internal memory address byte, after which the device issues an
acknowledge bit. The master device transmits another start condition followed by the DRV2604L address and the
read-write bit again. This time, the read-write bit is set to 1, indicating a read transfer. Next, the DRV2604L
device transmits the data byte from the memory address that is read. After receiving the data byte, the master
device transmits a not-acknowledge followed by a stop condition to complete the single-byte data read transfer.
See the note in the General I2C Operation section.
26
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
Acknowledge
A6
A5
A1
A0
W
ACK
A7
2
Start
Condition
Acknowledge
A6
A1
A0
ACK
A6
A5
A0
R
ACK
Acknowledge
D0 ACK
D7
2
Subaddress
I C device address and
R/W bit
Acknowledge
Repeat start I C device address and
condition
R/W bit
Data Byte
Stop
Condition
Figure 22. Single-Byte Read Transfer
8.5.3.6 Multiple-Byte Read
A multiple-byte data-read transfer is identical to a single-byte data-read transfer except that multiple data bytes
are transmitted by the DRV2604L device to the master device as shown in Figure 23. With the exception of the
last data byte, the master device responds with an acknowledge bit after receiving each data byte.
Acknowledge
A6
A0
W ACK A7
Start I2C device address
condition
and R/W bit
Acknowledge
A6
A1
A0 ACK
A6
A5
A0
Acknowledge
Acknowledge
Acknowledge
Acknowledge
R ACK D7
D0 ACK D7
D0 ACK D7
D0 ACK
Repeat start I2C device address
condition
and R/W bit
Subaddress
First data byte
Other data byte
Last data byte
Stop
condition
Figure 23. Multiple-Byte Read Transfer
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
27
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
8.5.4 Programming for Open-Loop Operation
The DRV2604L device can be used in open-loop mode and closed-loop mode. If open-loop operation is desired,
the first step is to determine which actuator type is to use, either ERM or LRA.
8.5.4.1 Programming for ERM Open-Loop Operation
To configure the DRV2604L device in ERM open-loop operation, the ERM must be selected by writing the
N_ERM_LRA bit to 0 (in register 0x1A), and the ERM_OPEN_LOOP bit to 1 in register 0x1D.
8.5.4.2 Programming for LRA Open-Loop Operation
To configure the DRV2604L device in LRA open-loop operation, the LRA must be selected by writing the
N_ERM_LRA bit to 1 in register 0x1A, and the LRA_OPEN_LOOP bit to 1 in register 0x1D. If PWM interface is
used, the open-loop frequency is given by the PWM frequency divided by 128. If PWM interface is not used, the
open-loop frequency is given by the OL_LRA_PERIOD[6:0] bit in register 0x20.
8.5.5 Programming for Closed-Loop Operation
For closed-loop operation, the device must be calibrated according to the actuator selection. When calibrated
accordingly, the user is only required to provide the desired waveform. The DRV2604L device automatically
adjusts the level and, for the LRA, automatically adjusts the driving frequency.
8.5.6 Auto Calibration Procedure
The calibration engine requires a number of bits as inputs before the engine can be executed (see Figure 24).
When the inputs are configured, the calibration routine can be executed. After calibration execution occurs, the
output parameters are written over the specified register locations. Figure 24 shows all of the required inputs and
generated outputs. To ensure proper auto-resonance operation, the LRA actuator type requires more input
parameters than the ERM. The LRA parameters are ignored when the device is in ERM mode.
Inputs
Outputs
ERM_LRA
BEMF_GAIN[1:0]
FB_BRAKE_FACTOR[2:0]
LOOP_GAIN[1:0]
RATED_VOLTAGE[7:0]
A_CAL_COMP[7:0]
OD_CLAMP[7:0]
AUTO_CAL_TIME[1:0]
Auto-calibration engine
DRIVE_TIME[4:0]
A_CAL_BEMF[7:0]
SAMPLE_TIME[1:0]
LRA
only
BLANKING_TIME[3:0]
IDISS_TIME[3:0]
DIAG_RESULT
ZC_DET_TIME[1:0]
Figure 24. Calibration-Engine Functional Diagram
Variation occurs between different actuators even if the actuators are of the same model. To ensure optimal
results, TI recommends that the calibration routine be run at least once for each actuator. The OTP feature of the
DRV2604L device can store the calibration values. Because of the stored values, the calibration procedure does
not have run every time. Having a single set of calibration register values that can be loaded during the system
initialization is possible.
28
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
The following instructions list the step-by-step register configuration for auto-calibration. For additional details see
the Register Map section.
1. Apply the supply voltage to the DRV2604L device, and pull the EN pin high. The supply voltage should allow
for adequate drive voltage of the selected actuator.
2. Write a value of 0x07 to register 0x01. This value moves the DRV2604L device out of STANDBY and places
the MODE[2:0] bits in auto-calibration mode.
3. Populate the input parameters required by the auto-calibration engine:
(a) ERM_LRA — selection will depend on desired actuator.
(b) FB_BRAKE_FACTOR[2:0] — A value of 2 is valid for most actuators.
(c) LOOP_GAIN[1:0] — A value of 2 is valid for most actuators.
(d) RATED_VOLTAGE[7:0] — See the Rated Voltage Programming section for calculating the correct
register value.
(e) OD_CLAMP[7:0] — See the Overdrive Voltage-Clamp Programming section for calculating the correct
register value.
(f) AUTO_CAL_TIME[1:0] — A value of 3 is valid for most actuators.
(g) DRIVE_TIME[3:0] — See the Drive-Time Programming for calculating the correct register value.
(h) SAMPLE_TIME[1:0] — A value of 3 is valid for most actuators.
(i) BLANKING_TIME[3:0] — A value of 1 is valid for most actuators.
(j) IDISS_TIME[3:0] — A value of 1 is valid for most actuators.
(k) ZC_DET_TIME[1:0] — A value of 0 is valid for most actuators.
4. Set the GO bit (write 0x01 to register 0x0C) to start the auto-calibration process. When auto calibration is
complete, the GO bit automatically clears. The auto-calibration results are written in the respective registers
as shown in Figure 24.
5. Check the status of the DIAG_RESULT bit (in register 0x00) to ensure that the auto-calibration routine is
complete without faults.
6. Evaluate system performance with the auto-calibrated settings. Note that the evaluation should occur during
the final assembly of the device because the auto-calibration process can affect actuator performance and
behavior. If any adjustment is required, the inputs can be modified and this sequence can be repeated. If the
performance is satisfactory, the user can do any of the following:
(a) Repeat the calibration process upon subsequent power ups.
(b) Store the auto-calibration results in host processor memory and rewrite them to the DRV2604L device
upon subsequent power ups. The device retains these settings when in STANDBY mode or when the EN
pin is low.
(c) Program the results permanently in nonvolatile, on-chip OTP memory. Even when a device power cycle
occurs, the device retains the auto-calibration settings. See the Programming On-Chip OTP Memory
section for additional information.
8.5.7 Programming On-Chip OTP Memory
The OTP memory can only be written once. To permanently program the OTP memory in registers 0x16 through
0x1A, use the following steps:
1. Write registers 0x16 through 0x1A with the desired configuration and calibration values which provide
satisfactory performance.
2. Ensure that the supply voltage (VDD) is between 4 V and 4.4 V. This voltage is required for the nonvolatile
memory to program properly.
3. Set the OTP_PROGRAM bit by writing a value of 0x01 to register 0x1E. When the OTP memory is written
which can only occur once in the device, the OTP_STATUS bit (in register 0x1E) only reads 1.
4. Reset the device by power cycling the device or setting the DEV_RESET bit in register 0x01, and then read
registers 0x16 to 0x1A to ensure that the programmed values were retained.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
29
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
8.5.8 Waveform Playback Programming
8.5.8.1 Data Formats for Waveform Playback
The DRV2604L smart-loop architecture has three modes of operation. Each of the modes can drive either ERM
or LRA devices.
1. Open-loop mode
2. Closed-loop mode (unidirectional)
3. Closed-loop mode (bidirectional)
Each mode has different advantages and disadvantages. The DRV2604L device brings new cutting-edge
actuator control with closed-loop operation around the back-EMF for automatic overdrive and braking. However,
some existing haptic implementations already include overdrive and braking that are embedded in the waveform
data. Open-loop mode is used to preserve compatibility with such systems.
The following sections show how the input data for each DRV2604L interface is translated to the output drive
signal.
30
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
8.5.8.1.1 Open-Loop Mode
In open-loop mode, the reference level for full-scale drive is set by the OD_CLAMP[7:0] bit in Register 0x17. A
mid-scale input value gives no drive signal, and a less-than mid-scale gives a negative drive value. For an ERM,
a negative drive value results in counter-rotation, or braking. For an LRA, a negative drive value results in a 180degree phase shift in commutation.
The RTP mode has 8 bits of resolution over the I2C bus. The RTP data can either be in a signed (2s
complement) or unsigned format as defined by the DATA_FORMAT_RTP bit.
Steady-State
Output Magnitude
Open Loop
ERM_OPEN_LOOP = 1 OR LRA_OPEN_LOOP = 1
OD_CLAMP[7:0]
0V
-OD_CLAMP[7:0]
Input
Input Interface
PWM
0%
50%
100%
RTP (8-bit) DATA_FORMAT_RTP = 0 0x81
0x00
0x7F
RTP (8-bit) DATA_FORMAT_RTP = 1 0x00
0x7F
0xFF
Figure 25.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
31
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
8.5.8.1.2 Closed-Loop Mode, Unidirectional
In closed-loop unidirectional mode, the DRV2604L device provides automatic overdrive and braking for both
ERM and LRA actuators. Closed-loop unidirectional mode is the easiest mode to use and understand. Closedloop unidirectional mode uses the full 8-bit resolution of the driver. Closed-loop unidirectional mode offers the
best performance; however, the data format is not physically compatible with the open-loop mode data that can
be used in some existing systems
The reference level for steady-state full-scale drive is set by the RATED_VOLTAGE[7:0] bit (when autocalibration is performed). The output voltage can momentarily exceed the rated voltage for automatic overdrive
and braking, but does not exceed the OD_CLAMP[7:0] voltage. Braking occurs automatically based on the input
signal when the back-EMF feedback determines that braking is necessary.
Because the system is unidirectional in closed-loop unidirectional mode, only unsigned data should be used. The
RTP mode has 8 bits of resolution over the I2C bus. Setting the DATA_FORMAT_RTP bit to 0 (signed) is not
recommended for closed-loop unidirectional mode.
Steady-State
Output Magnitude
Closed Loop, BIDIR_INPUT = 0
RATED_VOLTAGE[7:0]
½ RATED_VOLTAGE[7:0]
Full Braking
Input
Input Interface
PWM
0%
50%
RTP (8-bit) DATA_FORMAT_RTP = 1 0x00
0x7F
100%
0xFF
Figure 26.
For the RTP interface, set the DATA_FORMAT_RTP bit to 1 (unsigned).
32
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
8.5.8.1.3 Closed-Loop Mode, Bidirectional
In closed-loop bidirectional mode, the DRV2604L device provides automatic overdrive and braking for both ERM
and LRA devices. Closed-loop bidirectional mode preserves compatibility with data created in open-loop
signaling by maintaining zero drive-strength at the mid-scale value. When input values less than the mid-scale
value are given, the DRV2604L device interprets them as the same as the mid-scale with zero drive.
The reference level for steady-state full-scale drive is set by the RATED_VOLTAGE[7:0] bit (when auto
calibration is performed). The output voltage can momentarily exceed the rated voltage for automatic overdrive
and braking, but does not exceed the OD_CLAMP[7:0] voltage. Braking occurs automatically based on the input
signal when the back-EMF feedback determines that braking is necessary. Although the Closed-Loop mode
preserves compatibility with existing device data formats, it provides closed loop benefits and is the default
configuration at power up.
The RTP mode has 8 bits of resolution over the I2C bus. The RTP data can either be in signed (2s complement)
or unsigned format as defined by the DATA_FORMAT_RTP bit.
Steady-State
Output Magnitude
Closed Loop, BIDIR_INPUT = 1
RATED_VOLTAGE[7:0]
½ RATED_VOLTAGE[7:0]
Full Braking
Input
Input Interface
PWM
0%
50%
75%
100%
RTP (8-bit) DATA_FORMAT_RTP = 0 0x81
0x00
0x3F
0x7F
RTP (8-bit) DATA_FORMAT_RTP = 1 0x00
0x7F
0xBF
0xFF
Figure 27.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
33
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
8.5.8.2 Waveform Setup and Playback
Playback of a haptic effect can occur in multiple ways. Using the PWM mode, RTP mode, and analog-input
mode can provide the waveform in real time. The waveforms can also be played from the RAM in which case the
waveform playback engine is used and the waveform is either played by an internal GO bit (register 0x0C), or by
an external trigger.
8.5.8.2.1 Waveform Playback Using RTP Mode
The user can enter the RTP mode by writing the MODE[2:0] bit to 5 in register 0x01. When in RTP mode, the
DRV2604L device drives the actuator continuously with the amplitude specified in the RTP_INPUT[7:0] bit (in
register 0x02). Because the amplitude tracks the value specified in the RTP_INPUT[7:0] bit, the I2C bus can
stream waveforms.
8.5.8.2.2 Waveform Playback Using the Analog-Input Mode
The user can enter the analog-input mode by setting the MODE[2:0] bit to 3 in register 0x01 and by setting the
N_PWM_ANALOG bit to 1 in register 0x1D. When in analog-input mode, the DRV2604L device accepts an
analog voltage at the IN/TRIG pin. The DRV2604L device drives the actuator continuously in analog-input mode
until the user sets the device into STANDBY mode or enters another interface mode. The reference voltage in
analog-input mode is 1.8 V. Therefore a 1.8-V reference voltage is interpreted as a 100% input value, a 0.9-V
reference voltage is interpreted as 50%, and a 0-V reference voltage is interpreted as 0%. The input value is
analogous to the duty-cycle percentage in PWM mode. The interpretation of these percentages varies according
to the selected mode of operation. See the Data Formats for Waveform Playback section for details.
8.5.8.2.3 Waveform Playback Using PWM Mode
The user can enter the PWM mode by setting the MODE[2:0] bit to 3 in register 0x01 and by setting the
N_PWM_ANALOG bit to 0 in register 0x1D. When in PWM mode, the DRV2604L device accepts PWM data at
the IN/TRIG pin. The DRV2604L device drives the actuator continuously in PWM mode until the user sets the
device to STANDBY mode or to enter another interface mode. The interpretation of the duty-cycle information
varies according to the selected mode of operation. See the Data Formats for Waveform Playback section for
details.
8.5.8.2.4 Loading Data to RAM
The DRV2604LL device contains 2 kB of integrated RAM to store customer waveforms. The waveforms are
represented as time-amplitude pairs. Using the playback engine, the waveforms can be recalled, sequenced, and
played through the I2C or an external GPIO trigger.
A library consists of a revision byte (should be set to 0), a header section, and the waveform data content. The
library header defines the data boundaries for each effect ID in the data field, and the waveform data contains a
sequence of time-value pairs that define the effects.
RAM
0x000
Revision
Header
Waveform Data
0x7FF
Figure 28. RAM Memory Structure
34
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
8.5.8.2.4.1 Header Format
The header block consist of N-boundary definition blocks of 3 bytes each. N is the number of effects stored in the
RAM. Each of the boundary definition blocks contain the start address (2 bytes) and a configuration byte.
The start address contains the location in the memory where the waveform data associated with this effect
begins. The position of the effect pointer in the header becomes the effect ID. The first effect boundary definition
points to the ID for effect 1, the second definition points to the ID for effect 2, and so on. This resulting effect ID
is the effect ID that is used in the waveform sequencer.
Memory location
Header
0x000
0x001
0x004
0x007
(N ± 1) × 3 + 1
Effect ID
Revision
Start address
upper byte
Start address
upper byte
Start address
upper byte
Start address
lower byte
Start address
lower byte
Start address
lower byte
Start address
upper byte
Start address
lower byte
Configuration byte
Effect 1
Configuration byte
Effect 2
Configuration byte
Effect 3
Configuration byte
Effect N
Figure 29. Header Structure
The configuration byte contains the following two parameters:
• The effect size contains the amount of bytes that define the waveform data. An effect size of 0 is an error
state. Any odd-number effect size is an error state because the waveform data is defined as time-value (2
bytes). Therefore, the effect size must be an even number between 2 and 30.
• The WAVEFORM_REPEATS[2:0] bit is used to select the number of times the complete waveform is be
played when it is called by the waveform sequencer. A value of 0 is no repeat and the waveform is played
once. A value of 1 means 1 repeat and the waveform is played twice. A value of 7 means infinite repeat until
the GO bit is cleared.
During waveform design, ensure that the appropriate amount of drive time is at zero amplitude on the end of the
waveform so that the waveform stored in the RAM is repeated smoothly.
Configuration byte
Waveform repeats [2:0]
Effect size [4:0]
Figure 30. Header Configuration Byte Structure
8.5.8.2.4.2 RAM Waveform Data Format
The library data contents can take two forms which are voltage-time pair and linear ramp. The voltage-time pair
method implements a set and wait protocol, which is an efficient method of actuator control for most types of
waveforms. This method becomes inefficient when ramping waveforms is desired, therefore a linear ramp
method is also supported which linearly interpolates a set of voltages between two amplitude values. Both
methods require only two bytes of data per set point. The linear ramp method uses a minimum of four bytes so
that linear interpolation can be done to the next set point. The most significant bit of the voltage value is reserved
to indicate the linear ramping mode.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
35
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Programming (continued)
Waveform data
Ramp
Voltage [6:0]
Time [7:0]
Ramp
Voltage [6:0]
Time [7:0]
Ramp
Voltage [6:0]
Time [7:0]
Figure 31. Waveform Data Structure
Data is stored as interleaved voltage-time pairs. Voltage in the voltage-time pair is a 7-bit signed number with
range –63 to 63 when in bidirectional mode (BIDIR_INPUT = 1), and a 7-bit unsigned number with a range of 0
to 127 when in unidirectional mode (BIDIR_INPUT = 0). The MSB of the voltage byte is reserved for the linear
ramping mode.
The Time value is the number of ticks that the Voltage will last. The size of the tick depends on the
PLAYBACK_INTERVAL bit (in register 0x1F). If PLAYBACK_INTERVAL = 0 the absolute time is number of ticks
× 5 ms. If PLAYBACK_INTERVAL = 1 the absolute time is number ticks × 1 ms.
When the most significant bit of the Voltage is high, the engine interprets a linear interpolation between that
voltage and the following voltage point. The following voltage point can either be a part of a regular voltage-time
pair, or a subsequent ramp. The following lists the sequence of bytes:
1. Byte1 — Voltage1 (MSB High)
2. Byte2 — Time1
3. Byte3 — Voltage2
4. Byte4 — Time2
The engine creates a linear interpolation between Voltage1 and Voltage2 over the time period Time1, where
Time1 is a number of 5-ms ticks. The start value for the ramp is the 7-bit value contained in Voltage1. The end
amplitude is the 7-bit value contained in Voltage2. The MSB in Voltage2 can indicate a following voltage-time
pair or the starting point in a subsequent ramp.
8.5.8.2.5 Waveform Sequencer
If the user uses pre-stored effects, the effects must first be loaded into the waveform sequencer, and then the
effects can be launched by using any of the trigger options (see the Waveform Triggers section for details).
The waveform sequencer (see the Waveform Sequencer (Address: 0x04 to 0x0B) section) queues waveformlibrary identifiers for playback. Eight sequence registers queue up to eight library waveforms for sequential
playback. A waveform identifier is an integer value referring to the index position of a waveform in the RAM
library. Playback begins at register address 0x04 when the user asserts the GO bit (register 0x0C). When
playback of that waveform ends, the waveform sequencer plays the next waveform identifier held in register
0x05, if the next waveform is non-zero. The waveform sequencer continues in this way until the sequencer
reaches an identifier value of zero or until all eight identifiers are played (register addresses 0x04 through 0x0B),
whichever comes first.
The waveform identifier range is 1 to 127. The MSB of each sequence register can be used to implement a delay
between sequence waveforms. When the MSB is high, bits 6-0 indicate the length of the wait time. The wait time
for that step then becomes WAV_FRM_SEQ[6:0] × 10 ms.
36
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Programming (continued)
GO
Waveform Sequencer
RAM
WAV_FRM_SEQ0[7:0]
Effect 1
WAV_FRM_SEQ1[7:0]
Effect 2
WAV_FRM_SEQ2[7:0]
Effect 3
WAV_FRM_SEQ3[7:0]
Effect 4
WAV_FRM_SEQ4[7:0]
Effect 5
WAV_FRM_SEQ5[7:0]
WAV_FRM_SEQ6[7:0]
WAV_FRM_SEQ7[7:0]
Effect N
Figure 32. Waveform Sequencer Programming
8.5.8.2.6 Waveform Triggers
When the waveform sequencer has the effect (or effects) loaded, the waveform sequencer can be triggered by
an internal trigger, external trigger (edge), or external trigger (level). To trigger using the internal trigger set the
MODE[2:0] bit to 0 in register 0x01. To trigger using the external trigger (edge), set the MODE[2:0] bit to 1 and
then follow the trigger instructions listed in the Edge Trigger section. To trigger using the external trigger (level),
set the MODE[2:0] bit to 2 and then follow the trigger instructions listed in the Level Trigger section.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
37
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6 Register Map
Table 2. Register Map Overview
REG
NO.
DEFAULT
0x00
0xC0
0x01
0x40
0x02
0x00
0x03
0x00
0x04
0x01
WAIT1
WAV_FRM_SEQ1[6:0]
0x05
0x00
WAIT2
WAV_FRM_SEQ2[6:0]
0x06
0x00
WAIT3
WAV_FRM_SEQ3[6:0]
0x07
0x00
WAIT4
WAV_FRM_SEQ4[6:0]
0x08
0x00
WAIT5
WAV_FRM_SEQ5[6:0]
0x09
0x00
WAIT6
WAV_FRM_SEQ6[6:0]
0x0A
0x00
WAIT7
WAV_FRM_SEQ7[6:0]
0x0B
0x00
WAIT8
0x0C
0x00
0x0D
0x00
0x0E
0x00
SPT[7:0]
0x0F
0x00
SNT[7:0]
BIT 7
BIT 6
BIT 5
DEVICE_ID[2:0]
DEV_RESET
STANDBY
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Reserved
DIAG_RESULT
Reserved
OVER_TEMP
OC_DETECT
Reserved
MODE[2:0]
RTP_INPUT[7:0]
Reserved
HI_Z
Reserved
WAV_FRM_SEQ8[6:0]
Reserved
GO
ODT[7:0]
0x10
0x00
BRT[7:0]
0x16
0x3E
RATED_VOLTAGE[7:0]
0x17
0x9B
OD_CLAMP[7:0]
0x18
0x0C
A_CAL_COMP[7:0]
0x19
0x6F
0x1A
0x36
N_ERM_LRA
A_CAL_BEMF[7:0]
0x1B
0x93
STARTUP_BOOST
Reserved
0x1C
0xF5
BIDIR_INPUT
BRAKE_STABILIZER
0x1D
0x80
NG_THRESH[1:0]
0x1E
0x20
ZC_DET_TIME[1:0]
0x1F
0x80
AUTO_OL_CNT[1:0]
0x20
0x33
0x21
0x00
Reserved
FB_BRAKE_FACTOR[2:0]
LOOP_GAIN[1:0]
AC_COUPLE
SAMPLE_TIME[1:0]
ERM_OPEN_LOOP
BLANKING_TIME[1:0]
SUPPLY_COMP_DIS
LRA_DRIVE_MODE
N_PWM_ANALOG
LRA_OPEN_LOOP
Reserved
OTP_STATUS
Reserved
OTP_PROGRAM
PLAYBACK_INTERVAL
BLANKING_TIME[3:2]
IDISS_TIME[3:2]
OL_LRA_PERIOD[6:0]
VBAT[7:0]
0x22
0x00
LRA_PERIOD[7:0]
0xFD
0x00
RAM_ADDR_UB[7:0]
0xFE
0x00
RAM_ADDR_LB[7:0]
0xFF
0x00
RAM_DATA[7:0]
38
IDISS_TIME[1:0]
DATA_FORMAT_RTP
AUTO_CAL_TIME[1:0]
LRA_AUTO_OPEN_LOOP
BEMF_GAIN[1:0]
DRIVE_TIME[4:0]
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.1 Status (Address: 0x00)
Figure 33. Status Register
7
RO-1
6
DEVICE_ID[2:0]
RO-1
5
4
Reserved
RO-0
3
DIAG_RESULT
RO-0
2
Reserved
1
OVER_TEMP
RO-0
0
OC_DETECT
RO-0
Table 3. Status Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-5
DEVICE_ID[2:0]
RO
6
Device identifier. The DEVICE_ID bit indicates the part number to the user.
The user software can ascertain the device capabilities by reading this
register.
3: DRV2605 (contains licensed ROM library, does not contain RAM)
4: DRV2604 (contains RAM, does not contain licensed ROM library)
6: DRV2604L (low-voltage version of the DRV2604 device)
7: DRV2605L (low-voltage version of the DRV2605 device)
4
Reserved
3
DIAG_RESULT
RO
0
This flag stores the result of the auto-calibration routine and the diagnostic
routine. The flag contains the result for whichever routine was executed
last. The flag clears upon read. Test result is not valid until the GO bit selfclears at the end of the routine.
Auto-calibration mode:
0: Auto-calibration passed (optimum result converged)
1: Auto-calibration failed (result did not converge)
Diagnostic mode:
0: Actuator is functioning normally
1: Actuator is not present or is shorted, timing out, or giving
out–of-range back-EMF
2
Reserved
1
OVER_TEMP
RO
0
Latching overtemperature detection flag. If the device becomes too hot, it
shuts down. This bit clears upon read.
0: Device is functioning normally
1: Device has exceeded the temperature threshold
0
OC_DETECT
RO
0
Latching overcurrent detection flag. If the load impedance is below the
load-impedance threshold, the device shuts down and periodically attempts
to restart until the impedance is above the threshold.
0: No overcurrent event is detected
1: Overcurrent event is detected
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
39
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.2 Mode (Address: 0x01)
Figure 34. Mode Register
7
DEV_RESET
R/W-0
6
STANDBY
R/W-1
5
4
Reserved
3
2
1
MODE[2:0]
R/W-0
0
Table 4. Mode Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7
DEV_RESET
R/W
0
Device reset. Setting this bit performs the equivalent operation of power
cycling the device. Any playback operations are immediately interrupted,
and all registers are reset to the default values. The DEV_RESET bit selfclears after the reset operation is complete.
6
STANDBY
R/W
1
Software standby mode
0: Device ready
1: Device in software standby
5-3
Reserved
2-0
MODE
R/W
0
0: Internal trigger
Waveforms are fired by setting the GO bit in register 0x0C.
1: External trigger (edge mode)
A rising edge on the IN/TRIG pin sets the GO Bit. A second rising
edge on the IN/TRIG pin cancels the waveform if the second rising
edge occurs before the GO bit has cleared.
2: External trigger (level mode)
The GO bit follows the state of the external trigger. A rising edge on
the IN/TRIG pin sets the GO bit, and a falling edge sends a cancel. If
the GO bit is already in the appropriate state, no change occurs.
3: PWM input and analog input
A PWM or analog signal is accepted at the IN/TRIG pin and used as
the driving source. The device actively drives the actuator while in
this mode. The PWM or analog input selection occurs by using the
N_PWM_ANALOG bit.
4: Reserved.
5: Real-time playback (RTP mode)
The device actively drives the actuator with the contents of the
RTP_INPUT[7:0] bit in register 0x02.
6: Diagnostics
Set the device in this mode to perform a diagnostic test on the
actuator. The user must set the GO bit to start the test. The test is
complete when the GO bit self-clears. Results are stored in the
DIAG_RESULT bit in register 0x00.
7: Auto calibration
Set the device in this mode to auto calibrate the device for the
actuator. Before starting the calibration, the user must set the all
required input parameters. The user must set the GO bit to start the
calibration. Calibration is complete when the GO bit self-clears. For
more information see the Auto Calibration Procedure section.
40
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.3 Real-Time Playback Input (Address: 0x02)
Figure 35. Real-Time Playback Input Register
7
6
5
4
3
RTP_INPUT[7:0]
R/W-0
2
1
0
Table 5. Real-Time Playback Input Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
RTP_INPUT[7:0]
R/W
0
This field is the entry point for real-time playback (RTP) data. The
DRV2604L playback engine drives the RTP_INPUT[7:0] value to the load
when MODE[2:0] = 5 (RTP mode). The RTP_INPUT[7:0] value can be
updated in real-time by the host controller to create haptic waveforms. The
RTP_INPUT[7:0] value is interpreted as signed by default, but can be set to
unsigned by the DATA_FORMAT_RTP bit in register 0x1D. When the
haptic waveform is complete, the user can idle the device by setting
MODE[2:0] = 0, or alternatively by setting STANDBY = 1.
8.6.4 HI_Z (Address: 0x03)
Figure 36. HI_Z Register
7
6
Reserved
5
4
HI_Z
R/W-0
3
2
1
0
Reserved
Table 6. HI_Z Register Field Descriptions
BIT
FIELD
7-5
Reserved
4
HI_Z
3-0
Reserved
TYPE
DEFAULT
DESCRIPTION
R/W
0
This bit sets the output driver into a true high-impedance state. The device
must be enabled to go into the high-impedance state. When in hardware
shutdown or standby mode, the output drivers have 15 kO to ground. When
the HI_Z bit is asserted, the hi-Z functionality takes effect immediately, even
if a transaction is taking place.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
41
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.5 Waveform Sequencer (Address: 0x04 to 0x0B)
Figure 37. Waveform Sequencer Register
7
WAIT
R/W-0
6
5
4
3
WAV_FRM_SEQ[6:0]
R/W-0
2
1
0
Table 7. Waveform Sequencer Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7
WAIT
R/W
0
When this bit is set, the WAV_FRM_SEQ[6:0] bit is interpreted as a wait
time in which the playback engine idles. This bit is used to insert timed
delays between sequentially played waveforms.
Delay time = 10 ms × WAV_FRM_SEQ[6:0]
If WAIT = 0, then WAV_FRM_SEQ[6:0] is interpreted as a waveform
identifier for sequence playback.
6-0
WAV_FRM_SEQ
R/W
0
Waveform sequence value. This bit holds the waveform identifier of the
waveform to be played. A waveform identifier is an integer value referring
to the index position of a waveform in the RAM library. Playback begins at
register address 0x04 when the user asserts the GO bit (register 0x0C).
When playback of that waveform ends, the waveform sequencer plays the
next waveform identifier held in register 0x05, if the next waveform
identifier is non-zero. The waveform sequencer continues in this way until
the sequencer reaches an identifier value of zero, or all eight identifiers are
played (register addresses 0x04 through 0x0B), whichever comes first.
8.6.6 GO (Address: 0x0C)
Figure 38. GO Register
7
6
5
4
Reserved
3
2
1
0
GO
R/W-0
Table 8. GO Register Field Descriptions
BIT
FIELD
7-1
Reserved
0
GO
42
TYPE
DEFAULT
DESCRIPTION
R/W
0
This bit is used to fire processes in the DRV2604L device. The process
fired by the GO bit is selected by the MODE[2:0] bit (register 0x01). The
primary function of this bit is to fire playback of the waveform identifiers in
the waveform sequencer (registers 0x04 to 0x0B), in which case, this bit
can be thought of a software trigger for haptic waveforms. The GO bit
remains high until the playback of the haptic waveform sequence is
complete. Clearing the GO bit during waveform playback cancels the
waveform sequence. Using one of the external trigger modes can cause
the GO bit to be set or cleared by the external trigger pin. This bit can also
be used to fire the auto-calibration process or the diagnostic process.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.7 Overdrive Time Offset (Address: 0x0D)
Figure 39. Overdrive Time Offset Register
7
6
5
4
3
2
1
0
ODT[7:0]
R/W-0
Table 9. Overdrive Time Offset Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
ODT
R/W
0
This bit adds a time offset to the overdrive portion of the library
waveforms. Some motors require more overdrive time than others,
therefore this register allows the user to add or remove overdrive time
from the library waveforms. The maximum voltage value in the library
waveform is automatically determined to be the overdrive portion. This
register is only useful in open-loop mode. Overdrive is automatic for
closed-loop mode. The offset is interpreted as 2s complement, therefore
the time offset can be positive or negative.
Overdrive Time Offset (ms) = ODT[7:0] × PLAYBACK_INTERVAL
8.6.8 Sustain Time Offset, Positive (Address: 0x0E)
Figure 40. Sustain Time Offset, Positive Register
7
6
5
4
3
2
1
0
SPT[7:0]
R/W-0
Table 10. Sustain Time Offset, Positive Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
SPT
R/W
0
This bit adds a time offset to the positive sustain portion of the library
waveforms. Some motors have a faster or slower response time than
others, therefore this register allows the user to add or remove positive
sustain time from the library waveforms. Any positive voltage value other
than the overdrive portion is considered as a sustain positive value. The
offset is interpreted as 2s complement, therefore the time offset can positive
or negative.
Sustain-Time Positive Offset (ms) = SPT[7:0] ×
PLAYBACK_INTERVAL
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
43
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.9 Sustain Time Offset, Negative (Address: 0x0F)
Figure 41. Sustain Time Offset, Negative Register
7
6
5
4
3
2
1
0
SNT[7:0]
R/W-0
Table 11. Sustain Time Offset, Negative Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
SNT
R/W
0
This bit adds a time offset to the negative sustain portion of the library
waveforms. Some motors have a faster or slower response time than
others, therefore this register allows the user to add or remove negative
sustain time from the library waveforms. Any negative voltage value other
than the overdrive portion is considered as a sustaining negative value. The
offset is interpreted as two’s complement, therefore the time offset can be
positive or negative.
Sustain-Time Negative Offset (ms) = SNT[7:0] ×
PLAYBACK_INTERVAL
8.6.10 Brake Time Offset (Address: 0x10)
Figure 42. Brake Time Offset Register
7
6
5
4
3
2
1
0
BRT[7:0]
R/W-0
Table 12. Brake Time Offset Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
BRT
R/W
0
This bit adds a time offset to the braking portion of the library waveforms.
Some motors require more braking time than others, therefore this register
allows the user to add or take away brake time from the library waveforms.
The most negative voltage value in the library waveform is automatically
determined to be the braking portion. This register is only useful in open-loop
mode. Braking is automatic for closed-loop mode. The offset is interpreted as
2s complement, therefore the time offset can be positive or negative.
Brake Time Offset (ms) = BRT[7:0] × PLAYBACK_INTERVAL
44
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.11 Rated Voltage (Address: 0x16)
Figure 43. Rated Voltage Register
7
6
5
R/W-0
R/W-0
R/W-1
4
3
RATED_VOLTAGE[7:0]
R/W-1
R/W-1
2
1
0
R/W-1
R/W-1
R/W-0
Table 13. Rated Voltage Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
7-0
RATED_VOLTAGE[7:0]
R/W
0x3E
DESCRIPTION
This bit sets the reference voltage for full-scale output during closed-loop
operation. The auto-calibration routine uses this register as an input, therefore
this register must be written with the rated voltage value of the motor before
calibration is performed. This register is ignored for open-loop operation
because the overdrive voltage sets the reference for that case. Any
modification of this register value should be followed by calibration to set
A_CAL_BEMF appropriately.
See the Rated Voltage Programming section for calculating the correct register
value.
8.6.12 Overdrive Clamp Voltage (Address: 0x17)
Figure 44. Overdrive Clamp Voltage Register
7
6
5
R/W-1
R/W-0
R/W-0
4
3
OD_CLAMP[7:0]
R/W-1
R/W-1
2
1
0
R/W-0
R/W-1
R/W-1
Table 14. Overdrive Clamp Voltage Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7
OD_CLAMP[7:0]
R/W
0x9B
During closed-loop operation the actuator feedback allows the output voltage
to go above the rated voltage during the automatic overdrive and automatic
braking periods. This register sets a clamp so that the automatic overdrive is
bounded. This bit also serves as the full-scale reference voltage for open-loop
operation.
See the Overdrive Voltage-Clamp Programming section for calculating the
correct register value.
8.6.13 Auto-Calibration Compensation Result (Address: 0x18)
Figure 45. Auto-Calibration Compensation-Result Register
7
6
5
R/W-0
R/W-0
R/W-0
4
3
A_CAL_COMP[7:0]
R/W-0
R/W-1
2
1
0
R/W-1
R/W-0
R/W-0
Table 15. Auto-Calibration Compensation-Result Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
A_CAL_COMP[7:0]
R/W
0x0C
This register contains the voltage-compensation result after execution of auto
calibration. The value stored in the A_CAL_COMP bit compensates for any
resistive losses in the driver. The calibration routine checks the impedance of
the actuator to automatically determine an appropriate value. The autocalibration compensation-result value is multiplied by the drive gain during
playback.
Auto-calibration compensation coefficient = 1 + A_CAL_COMP[7:0] / 255
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
45
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.14 Auto-Calibration Back-EMF Result (Address: 0x19)
Figure 46. Auto-Calibration Back-EMF Result Register
7
6
5
R/W-0
R/W-1
R/W-1
4
3
A_CAL_BEMF[7:0]
R/W-0
R/W-1
2
1
0
R/W-1
R/W-0
R/W-0
Table 16. Auto-Calibration Back-EMF Result Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
A_CAL_BEMF[7:0]
R/W
0x6C
This register contains the rated back-EMF result after execution of auto
calibration. The A_CAL_BEMF[7:0] bit is the level of back-EMF voltage that the
actuator gives when the actuator is driven at the rated voltage. The DRV2604L
playback engine uses this the value stored in this bit to automatically determine
the appropriate feedback gain for closed-loop operation.
Auto-calibration back-EMF (V) = (A_CAL_BEMF[7:0] / 255) × 1.22 V /
BEMF_GAIN[1:0]
46
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.15 Feedback Control (Address: 0x1A)
Figure 47. Feedback Control Register
7
N_ERM_LRA
R/W-0
6
5
4
FB_BRAKE_FACTOR[2:0]
R/W-0
R/W-1
R/W-1
3
2
LOOP_GAIN[1:0]
R/W-0
R/W-1
1
0
BEMF_GAIN[1:0]
R/W-1
R/W-0
Table 17. Feedback Control Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7
N_ERM_LRA
R/W
0
This bit sets the DRV2604L device in ERM or LRA mode. This bit should be set
prior to running auto calibration.
0: ERM Mode
1: LRA Mode
6-4
FB_BRAKE_FACTOR[2:0]
R/W
3
This bit selects the feedback gain ratio between braking gain and driving gain.
In general, adding additional feedback gain while braking is desirable so that the
actuator brakes as quickly as possible. Large ratios provide less-stable
operation than lower ones. The advanced user can select to optimize this
register. Otherwise, the default value should provide good performance for most
actuators. This value should be set prior to running auto calibration.
0: 1x
1: 2x
2: 3x
3: 4x
4: 6x
5: 8x
6: 16x
7: Braking disabled
3-2
LOOP_GAIN[1:0]
R/W
1
This bit selects a loop gain for the feedback control. The LOOP_GAIN[1:0] bit
sets how fast the loop attempts to make the back-EMF (and thus motor velocity)
match the input signal level. Higher loop-gain (faster settling) options provide
less-stable operation than lower loop gain (slower settling). The advanced user
can select to optimize this register. Otherwise, the default value should provide
good performance for most actuators. This value should be set prior to running
auto calibration.
0: Low
1: Medium (default)
2: High
3: Very High
1-0
BEMF_GAIN[1:0]
R/W
2
This bit sets the analog gain of the back-EMF amplifier. This value is interpreted
differently between ERM mode and LRA mode. Auto calibration automatically
populates the BEMF_GAIN bit with the most appropriate value for the actuator.
ERM Mode
0: 0.255x
1: 0.7875x
2: 1.365x (default)
3: 3.0x
LRA Mode
0: 3.75x
1: 7.5x
2: 15x (default)
3: 22.5x
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
47
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.16 Control1 (Address: 0x1B)
Figure 48. Control1 Register
7
STARTUP_BO
OST
R/W-1
6
Reserved
5
AC_COUPLE
4
3
2
DRIVE_TIME[4:0]
1
0
R/W-0
R/W-1
R/W-0
R/W-0
R/W-1
R/W-1
Table 18. Control1 Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7
STARTUP_BOOST
R/W
1
This bit applies higher loop gain during overdrive to enhance actuator transient
response.
6
Reserved
5
AC_COUPLE
R/W
0
This bit applies a 0.9-V common mode voltage to the IN/TRIG pin when an ACcoupling capacitor is used. This bit is only useful for analog input mode. This bit
should not be asserted for PWM mode or external trigger mode.
0: Common-mode drive disabled for DC-coupling or digital inputs modes
1: Common-mode drive enabled for AC coupling
4-0
DRIVE_TIME[4:0]
R/W
0x13
LRA Mode: Sets initial guess for LRA drive-time in LRA mode. Drive time is
automatically adjusted for optimum drive in real time; however, this register
should be optimized for the approximate LRA frequency. If the bit is set too low,
it can affect the actuator startup time. If the bit is set too high, it can cause
instability.
Optimum drive time (ms) ≈ 0.5 × LRA Period
Drive time (ms) = DRIVE_TIME[4:0] × 0.1 ms + 0.5 ms
ERM Mode: Sets the sample rate for the back-EMF detection. Lower drive times
cause higher peak-to-average ratios in the output signal, requiring more supply
headroom. Higher drive times cause the feedback to react at a slower rate.
Drive Time (ms) = DRIVE_TIME[4:0] × 0.2 ms + 1 ms
48
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.17 Control2 (Address: 0x1C)
Figure 49. Control2 Register
7
BIDIR_INPUT
R/W-1
6
BRAKE_STABI
LIZER
R/W-1
5
4
SAMPLE_TIME[1:0]
3
2
BLANKING_TIME[1:0]
R/W-1
R/W-0
1
0
IDISS_TIME[1:0]
R/W-1
R/W-0
R/W-1
Table 19. Control2 Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7
BIDIR_INPUT
R/W
1
The BIDIR_INPUT bit selects how the engine interprets data.
0: Unidirectional input mode
Braking is automatically determined by the feedback conditions and is
applied when required. Use of this mode also recovers an additional bit
of vertical resolution. This mode should only be used for closed-loop
operation.
Examples::
0% Input ? No output signal
50% Input ? Half-scale output signal
100% Input ? Full-scale output signal
1: Bidirectional input mode (default)
This mode is compatible with traditional open-loop signaling and also
works well with closed-loop mode. When operating closed-loop, braking
is automatically determined by the feedback conditions and applied
when required. When operating open-loop modes, braking is only
applied when the input signal is less than 50%.
Open-loop mode (ERM and LRA) examples:
0% Input ? Negative full-scale output signal (braking)
25% Input ? Negative half-scale output signal (braking)
50% Input ? No output signal
75% Input ? Positive half-scale output signal
100% Input ? Positive full-scale output signal
Closed-loop mode (ERM and LRA) examples:
0% to 50% Input ? No output signal
50% Input ? No output signal
75% Input ? Half-scale output signal
100% Input ? Full-scale output signal
6
BRAKE_STABILIZER
R/W
1
When this bit is set, loop gain is reduced when braking is almost complete to
improve loop stability
5-4
SAMPLE_TIME[1:0]
R/W
1
LRA auto-resonance sampling time (Advanced use only)
0: 150 µs
1: 200 µs
2: 250 µs
3: 300 µs
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
49
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Table 19. Control2 Register Field Descriptions (continued)
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
3-2
BLANKING_TIME[1:0]
R/W
2
Blanking time before the back-EMF AD makes a conversion. (Advanced use only)
Blanking time for LRA has an additional 2 bits (BLANKING_TIME[3:2]) located in
register 0x1F. Depending on the status of N_ERM_LRA the blanking time
represents different values.
N_ERM_LRA = 0 (ERM mode)
0: 45 µs
1: 75 µs
2: 150 µs
3: 225 µs
N_ERM_LRA = 1(LRA mode)
0: 15 µs
1: 25 µs
2: 50 µs
3: 75 µs
4: 90 µs
5: 105 µs
6: 120 µs
7: 135 µs
8: 150 µs
9: 165 µs
10: 180 µs
11: 195 µs
12: 210 µs
13: 235 µs
14: 260 µs
15: 285 µs
50
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Table 19. Control2 Register Field Descriptions (continued)
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
1-0
IDISS_TIME[1:0]
R/W
2
Current dissipation time. This bit is the time allowed for the current to dissipate
from the actuator between PWM cycles for flyback mitigation. (Advanced use
only)
the current dissipation time for LRA has an additional 2 bits (IDISS_TIME[3:2])
located in register 0x1F. Depending on the status of N_ERM_LRA the idiss time
represents different values
N_ERM_LRA = 0 (ERM mode)
0: 45 µs
1: 75 µs
2: 150 µs
3: 225 µs
N_ERM_LRA = 1(LRA mode)
0: 15 µs
1: 25 µs
2: 50 µs
3: 75 µs
4: 90 µs
5: 105 µs
6: 120 µs
7: 135 µs
8: 150 µs
9: 165 µs
10: 180 µs
11: 195 µs
12: 210 µs
13: 235 µs
14: 260 µs
15: 285 µs
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
51
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.18 Control3 (Address: 0x1D)
Figure 50. Control3 Register
7
6
NG_THRESH[1:0]
R/W-1
R/W-0
5
ERM_OPEN_L
OOP
R/W-0
4
SUPPLY_COM
P_DIS
R/W-0
3
2
1
DATA_FORMA LRA_DRIVE_M N_PWM_ANAL
T_RTP
ODE
OG
R/W-0
R/W-0
R/W-0
0
LRA_OPEN_L
OOP
R/W-0
Table 20. Control3 Register Field Descriptions
BIT
7-6
FIELD
NG_THRESH[1:0]
TYPE
R/W
DEFAULT
2
DESCRIPTION
This bit is the noise-gate threshold for PWM and analog inputs.
0: Disabled
1: 2%
2: 4% (Default)
3: 8%
5
ERM_OPEN_LOOP
R/W
0
This bit selects mode of operation while in ERM mode. Closed-loop operation is
usually desired for because of automatic overdrive and braking properties.
However, many existing waveform libraries were designed for open-loop
operation, therefore open-loop operation can be required for compatibility.
0: Closed Loop
1: Open Loop
4
SUPPLY_COMP_DIS
R/W
0
This bit disables supply compensation. The DRV2604L device generally
provides constant drive output over variation in the power supply input (VDD). In
some systems, supply compensation can have already been implemented
upstream, therefore disabling the DRV2604L supply compensation can be
useful.
0: Supply compensation enabled
1: Supply compensation disabled
3
DATA_FORMAT_RTP
R/W
0
This bit selects the input data interpretation for RTP (Real-Time Playback)
mode.
0: Signed
1: Unsigned
2
LRA_DRIVE_MODE
R/W
0
This bit selects the drive mode for the LRA algorithm. This bit determines how
often the drive amplitude is updated. Updating once per cycle provides a
symmetrical output signal, while updating twice per cycle provides more precise
control.
0: Once per cycle
1: Twice per cycle
1
N_PWM_ANALOG
R/W
0
This bit selects the input mode for the IN/TRIG pin when MODE[2:0] = 3. In
PWM input mode, the duty cycle of the input signal determines the amplitude of
the waveform. In analog input mode, the amplitude of the input determines the
amplitude of the waveform.
0: PWM Input
1: Analog Input
0
LRA_OPEN_LOOP
R/W
0
This bit selects an open-loop drive option for LRA Mode. When asserted, the
playback engine drives the LRA at the selected frequency independently of the
resonance frequency. In PWM input mode, the playback engine recovers the
LRA commutation frequency from the PWM input, dividing the frequency by
128. Therefore the PWM input frequency must be equal to 128 times the
resonant frequency of the LRA.
In RTP, RAM mode, the frequency is set by the OL_LRA_PERIOD[6:0] bit.
Open-loop mode is not supported if analog input mode is selected.
0: Auto-resonance mode
1: LRA open-loop mode
52
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
8.6.19 Control4 (Address: 0x1E)
Figure 51. Control4 Register
7
6
ZC_DET_TIME[ ZC_DET_TIME[
1]
0]
R/W-0
R/W-0
5
4
AUTO_CAL_TIME[1:0]
R/W-1
3
Reserved
R/W-0
2
OTP_STATUS
R-0
1
Reserved
0
OTP_PROGRA
M
R/W-0
Table 21. Control4 Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-6
ZC_DET_TIME[1:0]
R/W
0
This bit sets the minimum length of time devoted for detecting a zero crossing
(advanced use only).
0: 100 µs
1: 200 µs
2: 300 µs
3: 390 µs
5-4
AUTO_CAL_TIME[1:0]
R/W
2
This bit sets the length of the auto calibration time. The AUTO_CAL_TIME[1:0]
bit should be enough time for the motor acceleration to settle when driven at the
RATED_VOLTAGE[7:0] value.
0: 150 ms (minimum), 350 ms (maximum)
1: 250 ms (minimum), 450 ms (maximum)
2: 500 ms (minimum), 700 ms (maximum)
3: 1000 ms (minimum), 1200 ms (maximum)
3
Reserved
2
OTP_STATUS
R
0
OTP Memory status
0: OTP Memory has not been programmed
1: OTP Memory has been programmed
1
Reserved
0
OTP_PROGRAM
R/W
0
This bit launches the programming process for one-time programmable (OTP)
memory which programs the contents of register 0x16 through 0x1A into
nonvolatile memory. This process can only be executed one time per device.
See the Programming On-Chip OTP Memory section for details.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
53
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.20 Control5 (Address: 0x1F)
Figure 52. Control5 Register
7
6
AUTO_OL_CNT[1:0]
R/W-1
5
LRA_AUTO_O
PEN_LOOP
R/W-0
R/W-0
4
PLAYBACK_IN
TERVAL
R/W-0
3
2
BLANKING_TIME[3:2]
RW-0
RW-0
1
0
IDISS_TIME[3:2]
RW-0
Table 22. Control5 Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-6
AUTO_OL_CNT[1:0]
R/W
2
This bit selects number of cycles required to attempt synchronization before
transitioning to open loop when the LRA_AUTO_OPEN_LOOP bit is asserted,
0: 3 attempts
1: 4 attempts
2: 5 attempts
3: 6 attempts
5
LRA_AUTO_OPEN_LOOP
R/W
0
This bit selects the automatic transition to open-loop drive when a back-EMF
signal is not detected (LRA only).
0: Never transitions to open loop
1: Automatically transitions to open loop
4
PLAYBACK_INTERVAL
R/W
0
This bit selects the memory playback interval.
0: 5 ms
1: 1 ms
3-2
BLANKING_TIME[3:2]
R/W
0
This bit sets the MSB for the BLANKING_TIME[3:0]. See the
BLANKING_TIME[3:0] bit in the Control2 (Address: 0x1C) section for details.
Advanced use only.
1-0
IDISS_TIME[3:2]
R/W
0
This bit sets the MSB for IDISS_TIME[3:0]. See the IDISS_TIME[1:0] bit in the
Control2 (Address: 0x1C) section for details. Advanced use only.
8.6.21 LRA Open Loop Period (Address: 0x20)
Figure 53. LRA Open Loop Period Register
7
Reserved
6
5
4
3
OL_LRA_PERIOD[6:0]
R/W-0
2
1
0
Table 23. LRA Open Loop Period Register Field Descriptions
BIT
7-0
FIELD
TYPE
OL_LRA_PERIOD[6:0]
DEFAULT
R/W
0
DESCRIPTION
This bit sets the period to be used for driving an LRA when open-loop mode is
selected.
LRA open-loop period (µs) = OL_LRA_PERIOD[6:0] × 98.46 µs
8.6.22 V(BAT) Voltage Monitor (Address: 0x21)
Figure 54. V(BAT) Voltage-Monitor Register
7
6
5
4
3
2
1
0
VBAT[7:0]
R/W-0
54
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
Table 24. V(BAT) Voltage-Monitor Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
VBAT[7:0]
R/W
0
This bit provides a real-time reading of the supply voltage at the VDD pin. The
device must be actively sending a waveform to take a reading.
VDD (V) = VBAT[7:0] × 5.6V / 255
8.6.23 LRA Resonance Period (Address: 0x22)
Figure 55. LRA Resonance-Period Register
7
6
5
4
3
LRA_PERIOD[7:0]
R/W-0
2
1
0
Table 25. LRA Resonance-Period Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
LRA_PERIOD[7:0]
R/W
0
This bit reports the measurement of the LRA resonance period. The device must
be actively sending a waveform to take a reading.
LRA period (us) = LRA_Period[7:0] × 98.46 µs
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
55
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
8.6.24 RAM-Address Upper Byte (Address: 0xFD)
Figure 56. RAM-Address Upper-Byte Register
7
6
5
4
3
RAM_ADDR_UB[7:0]
R/W-0
2
1
0
Table 26. RAM-Address Upper-Byte Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
RAM_ADDR_UB[7:0]
R/W
0
The content of this bit is the upper byte for the waveform RAM Address entry.
8.6.25 RAM-Address Lower Byte (Address: 0xFE)
Figure 57. RAM-Address Lower Byte Register
7
6
5
4
3
RAM_ADDR_LB[7:0]
R/W-0
2
1
0
Table 27. RAM Address Lower Byte Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
RAM_ADDR_LB[7:0]
R/W
0
The content of this bit is the lower byte for the waveform RAM address entry.
8.6.26 RAM Data Byte (Address: 0xFF)
Figure 58. RAM-Data Byte Register
7
6
5
4
3
RAM_DATA[7:0]
R/W-0
2
1
0
Table 28. RAM-Data Byte Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
RAM_DATA[7:0]
R/W
0
Data entry to waveform RAM interface. The user can perform single-byte writes
or multi-byte writes to this register. The controller starts the write at the address
(RAM_ADDR_UB:RAM_ADDR_LB). For both single-byte and multi-byte writes,
the controller automatically increments the RAM address register for each byte
written to the RAM data register.
56
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The typical application for a haptic driver is in a touch-enabled system that already has an application processor
which makes the decision on when to execute haptic effects.
The DRV2604L device can be used fully with I2C communications (either using RTP or the memory interface). A
system designer can chose to use external triggers to play low-latency effects (such as from a physical button) or
can decide to use the PWM interface. Figure 59 shows a typical haptic system implementation. The system
designer should not use the internal regulator (REG) to power any external load.
DRV2604L
Application
Processor
OUT+
C(REG)
SCL
SCL
REG
SDA
SDA
OUT±
M
LRA or
ERM
2 V ± 5.2 V
GPIO
PWM/GPIO
EN
VDD
IN/TRIG
GND
C(VDD)
Figure 59. I2C Control with Optional PWM Input or External Trigger
Table 29. Recommended External Components
COMPONENT
DESCRIPTION
SPECIFICATION
TYPICAL VALUE
0.1 µF
C(VDD)
Input capacitor
Capacitance
C(REG)
Regulator capacitor
Capacitance
1 µF
R(PU)
Pullup resistor
Resistance
2.2 kΩ
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
57
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
9.2 Typical Application
A typical application of the DRV2604L device is in a system that has external buttons which fire different haptic
effects when pressed. Figure 60 shows a typical schematic of such a system. The buttons can be physical
buttons, capacitive-touch buttons, or GPIO signals coming from the touch-screen system.
Effects in this type of system are programmable.
TPS73633
OUT
NR/FB
IN
EN
GND
C (LDO)
1 µF
R (PU)
2.2 kΩ
MSP430 G2553
C(VCC)
0.1 µF
R(SBW)
9 .76 kΩ
Programming
Captouch
Buttons
AVCC
DVCC
SBWTDIO
SBWTCK
P 2.0
P 2.1
DRV 2604 L
OUT+
P1.6/SCL
SCL
REG
P1.7/SDA
SDA
OUT –
P3.1
AVSS
R (PU)
2.2 kΩ
EN
VDD
IN /TRIG
GND
C (REG)
1 µF
M
LRA or
ERM
C(VDD)
1 µF
Li-ion
DVSS
Figure 60. Typical Application Schematic
9.2.1 Design Requirements
For this design example, use the values listed in Table 30 as the input parameters.
Table 30. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Interface
I2C, external trigger
Actuator type
LRA, ERM
Input power source
Li-ion/Li-polymer, 5-V boost
9.2.2 Detailed Design Procedure
9.2.2.1 Actuator Selection
The actuator decision is based on many factors including cost, form factor, vibration strength, powerconsumption requirements, haptic sharpness requirements, reliability, and audible noise performance. The
actuator selection is one of the most important design considerations of a haptic system and therefore the
actuator should be the first component to consider when designing the system. The following sections list the
basics of ERM and LRA actuators.
9.2.2.1.1 Eccentric Rotating-Mass Motors (ERM)
Eccentric rotating-mass motors (ERMs) are typically DC-controlled motors of the bar or coin type. ERMs can be
driven in the clockwise direction or counter-clockwise direction depending on the polarity of voltage across the
two pins. Bidirectional drive is made possible in a single-supply system by differential outputs that are capable of
sourcing and sinking current. The bidirectional drive feature helps eliminate long vibration tails which are
undesirable in haptic feedback systems.
58
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
IL
IL
OUT+
OUT+
+
Motor-spin
direction
±
Motor-spin
direction
VO
VO
+
±
OUT±
OUT±
IL
IL
Figure 61. Motor Spin Direction in ERM Motors
Another common approach to driving DC motors is the concept of overdrive voltage. To overcome the inertia of
the mass of the motor, the DC motors are often overdriven for a short amount of time before returning to the
rated voltage of the motor to sustain the rotation of the motor. Overdrive is also used to stop (or brake) a motor
quickly. Refer to the data sheet of the particular motor used with the DRV2604L device for safe and reliable
overdrive voltage and duration.
9.2.2.1.2 Linear Resonance Actuators (LRA)
Acceleration (g)
Linear resonant actuators (LRAs) vibrate optimally at the resonant frequency. LRAs have a high-Q frequency
response because of a rapid drop in vibration performance at the offsets of 3 to 5 Hz from the resonant
frequency. Many factors also cause a shift or drift in the resonant frequency of the actuator such as temperature,
aging, the mass of the product to which the LRA is mounted, and in the case of a portable product, the manner in
which the product is held. Furthermore, as the actuator is driven to the maximum allowed voltage, many LRAs
will shift several hertz in frequency because of mechanical compression. All of these factors make a real-time
tracking auto-resonant algorithm critical when driving LRA to achieve consistent, optimized performance.
Frequency (Hz)
¦(RESONANCE)
Figure 62. Typical LRA Response
9.2.2.1.2.1 Auto-Resonance Engine for LRA
The DRV2604L auto-resonance engine tracks the resonant frequency of an LRA in real time effectively locking
into the resonance frequency after half a cycle. If the resonant frequency shifts in the middle of a waveform for
any reason, the engine tracks the frequency from cycle to cycle. The auto resonance engine accomplishes this
tracking by constantly monitoring the back-EMF of the actuator. Note that the auto resonance engine is not
affected by the auto-calibration process which is only used for level calibration. No calibration is required for the
auto resonance engine.
9.2.2.2 Capacitor Selection
The DRV2604L device has a switching output stage which pulls transient currents through the VDD pin. TI
recommends placing a 0.1-µF low equivalent-series-resistance (ESR) supply-bypass capacitor of the X5R or
X7R type near the VDD supply pin for proper operation of the output driver and the digital portion of the device.
Place a 1-µF X5R or X7R-type capacitor from the REG pin to ground.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
59
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
9.2.2.3 Interface Selection
The I2C interface is required to configure the device. The device can be used fully with the I2C interface and with
either RTP or internal memory. The advantage of using the I2C interface is that no additional GPIO (for the
IN/TRIG pin) is required for firing effects, and no PWM signal is required to be generated. Therefore the IN/TRIG
pin can be connected to GND. Using the external trigger pin has the advantage that no I2C transaction is
required to fire the pre-loaded effect, which is a good choice for interfacing with a button. The PWM interface is
available for backward compatibility.
9.2.2.4 Power Supply Selection
The DRV2604L device supports a wide range of voltages in the input. Ensuring that the battery voltage is high
enough to support the desired vibration strength with the selected actuator is an important design consideration.
The typical application uses Li-ion or Li-polymer batteries which provide enough voltage headroom to drive most
common actuators.
If very strong vibrations are desired, a boost converter can be placed between the power supply and the VDD pin
to provide a constant voltage with a healthy headroom (5-V rails are common in some systems) which is
particularly true if two AA batteries in series are being used to power the system.
9.2.3 Application Curves
0
40m
VDD = 3.6 V
Strong click - 60%
80m
120m
Time (s)
160m
200m
ERM open loop
External edge trigger
0
40m
VDD = 3.6 V
Strong click - 100%
Figure 63. ERM Click with and without Braking
60
IN/TRIG
Acceleration
[OUT+] − [OUT−] (Filtered)
Voltage (2V/div)
Voltage (2V/div)
IN/TRIG
Acceleration
[OUT+] − [OUT−] (Filtered)
80m
120m
Time (s)
160m
200m
LRA closed loop
External level trigger
Figure 64. LRA Click With and Without Braking
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
9.3 Initialization Setup
9.3.1 Initialization Procedure
1.
2.
3.
4.
5.
6.
7.
8.
After powerup, wait at least 250 µs before the DRV2604L device accepts I2C commands.
Assert the EN pin (logic high). The EN pin can be asserted any time during or after the 250-µs wait period.
Write the MODE register (address 0x01) to value 0x00 to remove the device from standby mode.
If the nonvolatile auto-calibration memory has been programmed as described in the Auto Calibration
Procedure section, skip Step 5 and proceed to Step 6.
Perform the steps as described in the Auto Calibration Procedure section. Alternatively, rewrite the results
from a previous calibration.
If using the embedded RAM memory, populate the RAM with waveforms at this time as described in the
Loading Data to RAM section. Use registers 0xFD to 0xFF to access the RAM as described in the Table 2
procedure.
The default setup is closed-loop bidirectional mode. To use other modes and features, write Control1 (0x1B),
Control2 (0x1C), and Control3 (0x1D) as required.
Put the device in standby mode or deassert the EN pin, whichever is the most convenient. Both settings are
low-power modes. The user can select the desired MODE (address 0x01) at the same time the STANDBY
bit is set.
9.3.2 Typical Usage Examples
9.3.2.1 Play a Waveform or Waveform Sequence from the RAM Waveform Memory
1. Initialize the device as listed in the Initialization Procedure section.
2. Assert the EN pin (active high) if it was previously deasserted.
3. If register 0x01 already holds the desired value and the STANDBY bit is low, the user can skip this step.
Select the desired MODE[2:0] value of 0 (internal trigger), 1 (external edge trigger), or 2 (external level
trigger) in the MODE register (address 0x01). If the STANDBY bit was previously asserted, this bit should be
deasserted (logic low) at this time.
4. Select the waveform index to be played and write it to address 0x04. Alternatively, a sequence of waveform
indices can be written to register 0x04 through 0x0B. See the Waveform Sequencer section for details.
5. If using the internal trigger mode, set the GO bit (in register 0x0C) to fire the effect or sequence of effects. If
using an external trigger mode, send an appropriate trigger pulse to the IN/TRIG pin. See the Waveform
Triggers section for details.
6. If desired, the user can repeat Step 5 to fire the effect or sequence again.
7. Put the device in low-power mode by deasserting the EN pin or setting the STANDBY bit.
9.3.2.2 Play a Real-Time Playback (RTP) Waveform
1. Initialize the device as shown in the Initialization Procedure section.
2. Assert the EN pin (active high) if it was previously deasserted.
3. Set the MODE[2:0] value to 5 (RTP Mode) at address 0x01. If the STANDBY bit was previously asserted,
this bit should be deasserted (logic low) at this time. If register 0x01 already holds the desired value and the
STANDBY bit is low, the user can skip this step.
4. Write the desired drive amplitude to the real-time playback input register (address 0x02).
5. When the desired sequence of drive amplitudes is complete, put the device in low-power mode by
deasserting the EN pin or setting the STANDBY bit.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
61
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
Initialization Setup (continued)
9.3.2.3 Play a PWM or Analog Input Waveform
1. Initialize the device as shown in the Initialization Procedure section.
2. Assert the EN pin (active high) if it was previously deasserted.
3. If register 0x01 already holds the desired value and the STANDBY bit is low, the user can skip this step. Set
the MODE value to 3 (PWM/Analog Mode) at address 0x01. If the STANDBY bit was previously asserted,
this bit should be deasserted (logic low) at this time.
4. Select the input mode (PWM or analog) in the Control3 register (address 0x1D). If this mode was selected
during the initialization procedure, the user can skip this step.
5. Send the desired PWM or analog input waveform sequence from the external source. See the Data Formats
for Waveform Playback section for drive amplitude scaling.
6. When the desired drive sequence is complete, put the device in low-power mode by deasserting the EN pin
or setting the STANDBY bit.
10 Power Supply Recommendations
The DRV2604L device is designed to operate from an input-voltage supply range between 2 V to 5.2 V. The
decoupling capacitor for the power supply should be placed closed to the device pin.
62
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
11 Layout
11.1 Layout Guidelines
Use the following guidelines for the DRV2604L layout:
• The decoupling capacitor for the power supply (VDD) should be placed closed to the device pin.
• The filtering capacitor for the regulator (REG) should be placed close to the device REG pin.
• When creating the pad size for the WCSP pins, TI recommends that the PCB layout use nonsolder maskdefined (NSMD) land. With this method, the solder mask opening is made larger than the desired land area
and the opening size is defined by the copper pad width. Figure 65 shows and Table 31 lists appropriate
diameters for a wafer-chip scale package (WCSP) layout.
Copper
Trace Width
Solder
Pad Width
Solder Mask
Opening
Copper Trace
Thickness
Solder Mask
Thickness
Figure 65. Land Pattern Dimensions
Table 31. Land Pattern Dimensions
SOLDER PAD
DEFINITIONS
COPPER PAD
SOLDER MASK
OPENING
COPPER
THICKNESS
STENCIL
OPENING
STENCIL
THICKNESS
Nonsolder mask
defined (NSMD)
275 µm
(0, –25 µm)
375 µm
(0, –25 µm)
1-oz maximum (32 µm)
275 µm × 275 µm2
(rounded corners)
125-µm thick
1. Circuit traces from NSMD defined PWB lands should be 75-µm to 100-µm wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand-off and impact reliability.
2. The recommended solder paste is Type 3 or Type 4.
3. The best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating the range of the intended application.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less than 0.5 µm to avoid a reduction
in thermal fatigue performance.
5. Solder mask thickness should be less than 20 µm on top of the copper circuit pattern.
6. The best solder stencil performance is achieved using laser-cut stencils with electro polishing. Use of
chemically-etched stencils results in inferior solder paste volume control.
7. Trace routing away from the WCSP device should be balanced in X and Y directions to avoid unintentional
component movement because of solder-wetting forces.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
63
DRV2604L
SLOS866D – MAY 2014 – REVISED JUNE 2015
www.ti.com
11.1.1 Trace Width
The recommended trace width at the solder pins is 75 µm to 100 µm to prevent solder wicking onto wider PCB
traces. Maintain this trace width until the pin pattern has escaped, then the trace width can be increased for
improved current flow. The width and length of the 75-µm to 100-µm traces should be as symmetrical as possible
around the device to provide even solder reflow on each of the pins.
11.2 Layout Example
C(REG)
EN
REG
OUT+
IN
SDA
GND
Via
Via should connect
to a ground plane
SCL
VDD
OUTt
C(VDD)
Figure 66. DRV2604L Layout Example DSBGA
C(REG)
C(VDD)
REG
VDD
SCL
OUT-
SDA
GND
Via
IN/TRIG
OUT+
Via should connect
to a ground plane
EN
VDD/NC
Figure 67. DRV2604L Layout Example VSSOP
64
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
DRV2604L
www.ti.com
SLOS866D – MAY 2014 – REVISED JUNE 2015
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• Haptic Energy Consumption, SLOA194
• Haptic Implementation Considerations for Mobile and Wearable Devices, SLOA207
• LRA Actuators: How to Move Them?, SLOA209
• DRV2604L ERM, LRA Haptic Driver Evaluation Kit, SLOU390
• DRV2604LDGS Haptic Driver Mini Board, SLOU397
12.2 Community Resource
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
E2E is a trademark of Texas Instruments.
TouchSense is a registered trademark of Immersion Corporation.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13
Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2014–2015, Texas Instruments Incorporated
Product Folder Links: DRV2604L
65
PACKAGE OPTION ADDENDUM
www.ti.com
2-Jun-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DRV2604LDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 85
04L
DRV2604LDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 85
04L
DRV2604LYZFR
ACTIVE
DSBGA
YZF
9
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
2604L
DRV2604LYZFT
ACTIVE
DSBGA
YZF
9
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
2604L
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
2-Jun-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DRV2604LDGSR
Package Package Pins
Type Drawing
VSSOP
DGS
10
DRV2604LDGST
VSSOP
DGS
DRV2604LYZFR
DSBGA
YZF
DRV2604LYZFT
DSBGA
YZF
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.4
1.4
8.0
12.0
Q1
2500
330.0
12.4
10
250
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
9
3000
180.0
8.4
1.65
1.65
0.81
4.0
8.0
Q1
9
250
180.0
8.4
1.65
1.65
0.81
4.0
8.0
Q1
Pack Materials-Page 1
5.3
B0
(mm)
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DRV2604LDGSR
VSSOP
DGS
10
2500
366.0
364.0
50.0
DRV2604LDGST
VSSOP
DGS
10
250
366.0
364.0
50.0
DRV2604LYZFR
DSBGA
YZF
9
3000
182.0
182.0
20.0
DRV2604LYZFT
DSBGA
YZF
9
250
182.0
182.0
20.0
Pack Materials-Page 2
D: Max = 1.47 mm, Min = 1.41 mm
E: Max = 1.47 mm, Min = 1.41 mm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated