8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP AD7927 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM Fast throughput rate: 200 kSPS Specified for AVDD of 2.7 V to 5.25 V Low power 3.6 mW maximum at 200 kSPS with 3 V supply 7.5 mW maximum at 200 kSPS with 5 V supply 8 (single-ended) inputs with sequencer Wide input bandwidth 70 dB minimum SINAD at 50 kHz input frequency Flexible power/serial clock speed management No pipeline delays High speed serial interface SPI-, QSPI™-, MICROWIRE™-, DSP-compatible Shutdown mode: 0.5 μA maximum 20-lead TSSOP Qualified for automotive applications AVDD REFIN VIN0 12-BIT SUCCESSIVE APPROXIMATION ADC T/H INPUT MUX VIN7 SCLK CONTROL LOGIC SEQUENCER DOUT DIN VDRIVE AGND GENERAL DESCRIPTION 03088-001 CS AD7927 Figure 1. The AD7927 is a 12-bit, high speed, low power, 8-channel, successive approximation ADC. The part operates from a single 2.7 V to 5.25 V power supply and features throughput rates up to 200 kSPS. The part contains a low noise, wide bandwidth track-and-hold amplifier that can handle input frequencies in excess of 8 MHz. PRODUCT HIGHLIGHTS 1. High Throughput with Low Power Consumption. The AD7927 offers up to 200 kSPS throughput rates. At the maximum throughput rate with 3 V supplies, the AD7927 dissipates 3.6 mW of power maximum. The conversion process and data acquisition are controlled using CS and the serial clock signal, allowing the device to easily interface with microprocessors or DSPs. The input signal is sampled on the falling edge of CS and the conversion is also initiated at this point. There are no pipeline delays associated with the part. 2. Eight Single-Ended Inputs with a Channel Sequencer. A consecutive sequence of channels can be selected on which the ADC cycles and converts. 3. Single-Supply Operation with VDRIVE Function. The AD7927 operates from a single 2.7 V to 5.25 V supply. The VDRIVE function allows the serial interface to connect directly to either 3 V or 5 V processor systems independent of AVDD. 4. Flexible Power/Serial Clock Speed Management. The conversion rate is determined by the serial clock, allowing the conversion time to be reduced through the serial clock speed increase. The part also features various shutdown modes to maximize power efficiency at lower throughput rates. Current consumption is 0.5 μA maximum when in full shutdown. 5. No Pipeline Delay. The part features a standard successive approximation ADC with a CS input pin, which allows for accurate control of each sampling instant. The AD7927 uses advanced design techniques to achieve very low power dissipation at maximum throughput rates. At maximum throughput rates, the AD7927 consumes 1.2 mA maximum with 3 V supplies; with 5 V supplies, the current consumption is 1.5 mA maximum. Through the configuration of the control register, the analog input range for the part can be selected as 0 V to REFIN or 0 V to 2 × REFIN, with either straight binary or twos complement output coding. The AD7927 features eight single-ended analog inputs with a channel sequencer to allow a preprogrammed selection of channels to be converted sequentially. The conversion time for the AD7927 is determined by the SCLK frequency, as this is also used as the master clock to control the conversion. The conversion time may be as short as 800 ns with a 20 MHz SCLK. Rev. D Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2003–2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD7927* PRODUCT PAGE QUICK LINKS Last Content Update: 02/23/2017 COMPARABLE PARTS DESIGN RESOURCES View a parametric search of comparable parts. • AD7927 Material Declaration • PCN-PDN Information EVALUATION KITS • Quality And Reliability • AD7927 Evaluation kit • Symbols and Footprints DOCUMENTATION DISCUSSIONS Data Sheet View all AD7927 EngineerZone Discussions. • AD7927: 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP Data Sheet SAMPLE AND BUY Product Highlight Visit the product page to see pricing options. • 8- to 18-Bit SAR ADCs ... From the Leader in High Performance Analog REFERENCE MATERIALS TECHNICAL SUPPORT Submit a technical question or find your regional support number. Technical Articles • MS-2210: Designing Power Supplies for High Speed ADC DOCUMENT FEEDBACK Submit feedback for this data sheet. This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified. AD7927 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Analog Input Selection .............................................................. 17 General Description ......................................................................... 1 Digital Inputs .............................................................................. 17 Functional Block Diagram .............................................................. 1 VDRIVE ............................................................................................ 18 Product Highlights ........................................................................... 1 The Reference ............................................................................. 18 Revision History ............................................................................... 2 Modes of Operation ....................................................................... 19 Specifications..................................................................................... 3 Normal Mode (PM1 = PM0 = 1) ............................................. 19 Timing Specifications .................................................................. 5 Full Shutdown (PM1 = 1, PM0 = 0) ........................................ 19 Absolute Maximum Ratings............................................................ 6 Auto Shutdown (PM1 = 0, PM0 = 1)....................................... 20 ESD Caution .................................................................................. 6 Powering Up the AD7927 ......................................................... 21 Pin Configuration and Function Descriptions ............................. 7 Power vs. Throughput Rate ....................................................... 21 Terminology ...................................................................................... 8 Serial Interface ................................................................................ 22 Typical Performance Characteristics ........................................... 10 Writing Between Conversions .................................................. 22 Control Register .............................................................................. 12 Microprocessor Interfacing ........................................................... 24 Sequencer Operation...................................................................... 13 AD7927 to TMS320C541 .......................................................... 24 Shadow Register .............................................................................. 14 AD7927 to ADSP-21xx .............................................................. 24 Circuit Information .................................................................... 15 AD7927 to DSP563xx ................................................................ 25 Converter Operation .................................................................. 15 Application Hints ........................................................................... 26 Analog Input ............................................................................... 15 Grounding and Layout .............................................................. 26 ADC Transfer Function ............................................................. 16 Outline Dimensions ....................................................................... 27 Handling Bipolar Input Signals ................................................ 16 Ordering Guide .......................................................................... 27 Typical Connection Diagram ........................................................ 17 Automotive Products ................................................................. 27 REVISION HISTORY 6/13—Rev. C to Rev. D Deleted Evaluating the AD7927 Performance Section .............. 26 Changes to Ordering Guide .......................................................... 27 12/08—Rev. A to Rev. B Changes to ESD Parameter, Table 3 ................................................6 Changes to Ordering Guide .......................................................... 27 12/11—Rev. B to Rev. C Changes to Features Section............................................................ 1 Changes to Table 1 ............................................................................ 3 Changes to Table 3 ............................................................................ 6 Changes to Ordering Guide, Added Automotive Products Section .............................................................................................. 27 1/07—Rev. 0 to Rev. A Updated Format .................................................................. Universal Updated Layout .................................................................................8 Updated Layout .............................................................................. 10 Changes to Figure 12 Caption ...................................................... 14 Changes to Figure 13 Caption ...................................................... 15 Changes to Ordering Guide .......................................................... 27 1/03—Revision 0: Initial Version Rev. D | Page 2 of 28 Data Sheet AD7927 SPECIFICATIONS AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz; TA = TMIN to TMAX, unless otherwise noted. Table 1. Parameter DYNAMIC PERFORMANCE Signal-to-(Noise + Distortion) (SINAD)2 Signal-to-Noise Ratio (SNR)2 Total Harmonic Distortion (THD) 2 Peak Harmonic or Spurious Noise (SFDR) 2 Intermodulation Distortion (IMD)2 Second-Order Terms Third-Order Terms Aperture Delay Aperture Jitter Channel-to-Channel Isolation2 Full Power Bandwidth DC ACCURACY2 Resolution Integral Nonlinearity Differential Nonlinearity 0 V to REFIN Input Range Offset Error Offset Error Match Gain Error Gain Error Match 0 V to 2 × REFIN Input Range Positive Gain Error Positive Gain Error Match Zero Code Error Zero Code Error Match Negative Gain Error Negative Gain Error Match ANALOG INPUT Input Voltage Ranges B Version1 Unit 70 69.5 69 70 69.5 −77 −73 −78 −76 dB min dB min dB min dB min dB min dB max dB max dB max dB max −90 −90 10 50 −82 8.2 1.6 dB typ dB typ ns typ ps typ dB typ MHz typ MHz typ 12 ±1 −0.9/+1.5 Bits LSB max LSB max ±8 ±0.5 ±1.5 ±0.5 LSB max LSB max LSB max LSB max Test Conditions/Comments fIN = 50 kHz sine wave, fSCLK = 20 MHz @ 5 V, B models @ 5 V, W models @ 3 V Typically 70 dB B models W models @ 5 V Typically −84 dB @ 3 V Typically −77 dB @ 5 V Typically −86 dB @ 3 V Typically −80 dB fA = 40.1 kHz, fB = 41.5 kHz fIN = 400 kHz @ 3 dB @ 0.1 dB Guaranteed no missed codes to 12 bits Straight binary output coding Typically ±0.5 LSB −REFIN to +REFIN biased about REFIN with Twos complement output coding ±1.5 ±0.5 ±8 ±0.5 ±1 ±0.5 LSB max LSB max LSB max LSB max LSB max LSB max V V μA max pF typ RANGE bit set to 1 RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to 5.25 V DC Leakage Current Input Capacitance REFERENCE INPUT REFIN Input Voltage DC Leakage Current REFIN Input Impedance 0 to REFIN 0 to 2 × REFIN ±1 20 2.5 ±1 36 V μA max kΩ typ ±1% specified performance LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN3 0.7 × VDRIVE 0.3 × VDRIVE ±1 10 V min V max μA max pF max Rev. D | Page 3 of 28 Typically ±0.8 LSB fSAMPLE = 200 kSPS Typically 10 nA, VIN = 0 V or VDRIVE AD7927 Parameter LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance3 Output Coding Straight (Natural) Binary Twos Complement CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time Throughput Rate POWER REQUIREMENTS AVDD VDRIVE IDD4 During Conversion Normal Mode (Static) Normal Mode (Operational) fSAMPLE = 200 kSPS Using Auto Shutdown Mode fSAMPLE = 200 kSPS Auto Shutdown (Static) Full Shutdown Mode Power Dissipation4 Normal Mode (Operational) Auto Shutdown (Static) Full Shutdown Mode Data Sheet B Version1 Unit Test Conditions/Comments VDRIVE − 0.2 0.4 ±1 10 V min V max μA max pF max ISOURCE = 200 μA, AVDD = 2.7 V to 5.25 V ISINK = 200 μA Coding bit set to 1 Coding bit set to 0 800 300 300 200 ns max ns max ns max kSPS max 2.7/5.25 2.7/5.25 V min/max V min/max 2.7 2 600 1.5 1.2 900 650 0.5 0.5 mA max mA max μA typ mA max mA max μA typ μA typ μA max μA max Digital inputs = 0 V or VDRIVE AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz AVDD = 2.7 V to 5.25 V, SCLK on or off AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz SCLK on or off (20 nA typ) SCLK on or off (20 nA typ) 7.5 3.6 2.5 1.5 2.5 1.5 mW max mW max μW max μW max μW max μW max AVDD = 5 V, fSCLK = 20 MHz AVDD = 3 V, fSCLK = 20 MHz AVDD = 5 V AVDD = 3 V AVDD = 5 V AVDD = 3 V 1 Temperature ranges as follows: B Version: −40°C to +85°C; W Version: −40°C to +125°C. See Terminology section. 3 Sample tested @ 25°C to ensure compliance. 4 See Power vs. Throughput Rate section. 2 Rev. D | Page 4 of 28 16 SCLK cycles with SCLK at 20 MHz Sine wave input Full-scale step input See Serial Interface section Data Sheet AD7927 TIMING SPECIFICATIONS1 AVDD = 2.7 V to 5.25 V, VDRIVE ≤ AVDD, REFIN = 2.5 V; TA = TMIN to TMAX, unless otherwise noted. Table 2. Parameter fSCLK2 tCONVERT tQUIET AVDD = 3 V 10 20 16 × tSCLK 50 t2 t33 t43 t5 t6 t7 t84 t9 t10 t11 t12 10 35 40 0.4 × tSCLK 0.4 × tSCLK 10 15/45 10 5 20 1 Limit at TMIN, TMAX AD7927 AVDD = 5 V Unit 10 kHz min 20 MHz max 16 × tSCLK 50 ns min 10 30 40 0.4 × tSCLK 0.4 × tSCLK 10 15/35 10 5 20 1 Description Minimum quiet time required between CS rising edge and start of next conversion CS to SCLK setup time Delay from CS until DOUT three-state disabled Data access time after SCLK falling edge SCLK low pulsewidth SCLK high pulsewidth SCLK to DOUT valid hold time SCLK falling edge to DOUT high impedance DIN setup time prior to SCLK falling edge DIN hold time after SCLK falling edge Sixteenth SCLK falling edge to CS high Power-up time from full power-down/auto shutdown mode ns min ns max ns max ns min ns min ns min ns min/max ns min ns min ns min μs max 1 Sample tested at 25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of AVDD) and timed from a voltage level of 1.6 V, (see Figure 2). The 3 V operating range spans from 2.7 V to 3.6 V. The 5 V operating range spans from 4.75 V to 5.25 V. Mark/space ratio for the SCLK input is 40/60 to 60/40. 3 Measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.4 V or 0.7 × VDRIVE. 4 t8 is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means the time, quoted in the t8 timing characteristics, is the true bus relinquish time of the part and is independent of the bus loading. 2 200µA 1.6V CL 50pF 200µA IOH 03088-002 TO OUTPUT PIN IOL Figure 2. Load Circuit for Digital Output Timing Specifications Rev. D | Page 5 of 28 AD7927 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 3. Parameter AVDD to AGND VDRIVE to AGND Analog Input Voltage to AGND Digital Input Voltage to AGND Digital Output Voltage to AGND REFIN to AGND Input Current to Any Pin Except Supplies1 Operating Temperature Range Commercial (B Version) Automotive (W Version) Storage Temperature Range Junction Temperature TSSOP, Power Dissipation θJA Thermal Impedance θJC Thermal Impedance Lead Temperature, Soldering Vapor Phase (60 sec) Infrared (15 sec) ESD 1 Rating −0.3 V to +7 V −0.3 V to AVDD + 0.3 V −0.3 V to AVDD + 0.3 V −0.3 V to +7 V −0.3 V to AVDD + 0.3 V −0.3 V to AVDD + 0.3 V ±10 mA Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION −40°C to +85°C −40°C to +125°C −65°C to +150°C 150°C 450 mW 143°C/W (TSSOP) 45°C/W (TSSOP) 215°C 220°C 1.5 kV Transient currents of up to 100 mA do not cause SCR latch-up. Rev. D | Page 6 of 28 Data Sheet AD7927 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SCLK 1 20 AGND DIN 2 3 AGND 4 AD7927 VDRIVE 18 DOUT 17 AGND TOP VIEW (Not to Scale) 16 V 0 IN AVDD 5 VIN1 AVDD 6 15 REFIN 7 14 VIN2 AGND 8 13 VIN3 VIN7 9 12 VIN4 VIN6 10 11 VIN5 03088-003 CS 19 Figure 3. 20-Lead TSSOP Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic SCLK 2 DIN 3 CS 4, 8, 17, 20 AGND 5, 6 AVDD 7 REFIN 16 to 9 VIN0 to VIN7 18 DOUT 19 VDRIVE Description Serial Clock. Logic input. SCLK provides the serial clock for accessing data from the part. This clock input is also used as the clock source for the AD7927 conversion process. Data In. Logic input. Data to be written to the AD7927 control register is provided on this input and is clocked into the register on the falling edge of SCLK (see the Control Register section). Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the AD7927 and framing the serial data transfer. Analog Ground. Ground reference point for all analog circuitry on the AD7927. All analog input signals and any external reference signal should be referred to this AGND voltage. All AGND pins should be connected together. Analog Power Supply Input. The AVDD range for the AD7927 is from 2.7 V to 5.25 V. For the 0 V to 2 × REFIN range, AVDD should be from 4.75 V to 5.25 V. Reference Input for the AD7927. An external reference must be applied to this input. The voltage range for the external reference is 2.5 V ±1% for specified performance. Analog Input 0 through Analog Input 7. Eight single-ended analog input channels that are multiplexed into the on-chip track-and-hold. The analog input channel to be converted is selected by using the address bits (ADD2 through ADD0) of the control register. ADD2 through ADD0, in conjunction with the SEQ and SHADOW bits, allow the sequencer to be programmed. The input range for all input channels can extend from 0 V to REFIN or 0 V to 2 × REFIN, as selected via the RANGE bit in the control register. Any unused input channels should be connected to AGND to avoid noise pickup. Data Out. Logic output. The conversion result from the AD7927 is provided on this output as a serial data stream. The bits are clocked out on the falling edge of the SCLK input. The data stream from the AD7927 consists of two leading zeros, two address bits indicating which channel the conversion result corresponds to, followed by the 12 bits of conversion data (MSB first). The output coding may be selected as straight binary or twos complement via the CODING bit in the control register. Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the serial interface of the AD7927 operates. Rev. D | Page 7 of 28 AD7927 Data Sheet TERMINOLOGY Integral Nonlinearity (INL) INL is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale, a point 1 LSB below the first code transition, and full scale, a point 1 LSB above the last code transition. Figure 9 shows a typical INL plot for the AD7927. Negative Gain Error This applies when using the twos complement output coding option, in particular to the 2 × REFIN input range with −REFIN to +REFIN biased about the REFIN point. It is the deviation of the first code transition (100 . . . 000) to (100 . . . 001) from the ideal (that is, −REFIN + 1 LSB) after the zero code error has been adjusted out. Differential Nonlinearity (DNL) DNL is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Figure 10 shows a typical DNL plot for the AD7927. Negative Gain Error Match This is the difference in negative gain error between any two channels. Offset Error This is the deviation of the first code transition (00 . . . 000) to (00 . . . 001) from the ideal, that is, AGND + 1 LSB. Offset Error Match This is the difference in offset error between any two channels. Gain Error This is the deviation of the last code transition (111 . . . 110) to (111 . . . 111) from the ideal (that is, REFIN − 1 LSB) after the offset error has been adjusted out. Gain Error Match This is the difference in gain error between any two channels. Channel-to-Channel Isolation Channel-to-channel isolation is a measure of the level of crosstalk between channels. It is measured by applying a fullscale 400 kHz sine wave signal to all seven nonselected input channels and determining how much that signal is attenuated in the selected channel with a 50 kHz signal. The figure given is the worst case across all eight channels for the AD7927. Power Supply Rejection (PSR) Variations in power supply affect the full-scale transition, but not the converter’s linearity. Power supply rejection is the maximum change in full-scale transition point due to a change in power supply voltage from the nominal value (see the Typical Performance Characteristics section). Zero Code Error This applies when using the twos complement output coding option, in particular to the 2 × REFIN input range with −REFIN to +REFIN biased about the REFIN point. It is the deviation of the midscale transition (all 0s to all 1s) from the ideal VIN voltage, that is, REFIN − 1 LSB. Power Supply Rejection Ration (PSRR) The power supply rejection ratio is defined as the ratio of the power in the ADC output at full-scale frequency (f) to the power of a 200 mV p-p sine wave applied to the ADC AVDD supply of frequency (fS): Zero Code Error Match This is the difference in zero code error between any two channels. where: Pf is equal to the power at Frequency f in ADC output. PfS is equal to the power at Frequency fS coupled onto the ADC AVDD. Positive Gain Error This applies when using the twos complement output coding option, in particular to the 2 × REFIN input range with −REFIN to +REFIN biased about the REFIN point. It is the deviation of the last code transition (011. . .110) to (011 . . . 111) from the ideal (that is, +REFIN − 1 LSB) after the zero code error has been adjusted out. Here a 200 mV p-p sine wave is coupled onto the AVDD supply. Figure 6 shows the power supply rejection ratio vs. supply ripple frequency for the AD7927 with no decoupling. Positive Gain Error Match This is the difference in positive gain error between any two channels. PSRR(dB) = 10log(Pf/PfS) Track-and-Hold Acquisition Time The track-and-hold amplifier returns into track mode at the end of conversion. Track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within ±1 LSB, after the end of conversion. Rev. D | Page 8 of 28 Data Sheet AD7927 Signal-to-(Noise + Distortion) Ratio (SINAD) This is the measured ratio of signal-to-(noise + distortion) at the output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical signal-to-(noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by Signal-to-(Noise + Distortion) = (6.02N + 1.76)dB Thus, for a 12-bit converter, this is 74 dB. Figure 5 shows the signal-to-(noise + distortion) ratio performance vs. input frequency for various supply voltages while sampling at 200 kSPS with an SCLK of 20 MHz. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of harmonics to the fundamental. For the AD7927, it is defined as: THD(dB) 20 log V22 V32 V 42 V52 V62 V1 where: V1 is the rms amplitude of the fundamental. V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Figure 7 shows a graph of total harmonic distortion vs. analog input frequency for various supply voltages, and Figure 8 shows a graph of total harmonic distortion vs. analog input frequency for various source impedances (see the Analog Input section). Rev. D | Page 9 of 28 AD7927 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 0 4096 POINT FFT AVDD = 4.75V fSAMPLE = 200kSPS fIN = 50kHz SINAD = 70.714dB THD = –82.853dB SFDR = –84.815dB –10 –20 –30 PSRR (dB) SNR (dB) –30 AVDD = 5V 200mV p-p SINE WAVE ON AVDD REFIN = 2.5V, 1µF CAPACITOR TA = 25°C –10 –50 –40 –50 –60 –70 –70 –90 0 10 20 30 40 50 60 70 FREQUENCY (kHz) 80 90 100 –90 03088-004 –110 0 Figure 4. Dynamic Performance at 200 kSPS 20 40 60 80 100 120 140 160 SUPPLY RIPPLE FREQUENCY (kHz) 180 200 03088-006 –80 Figure 6. PSRR vs. Supply Ripple Frequency 75 –50 –55 AVDD = VDRIVE = 5.25V AVDD = VDRIVE = 4.75V fSAMPLE = 200kSPS TA = 25°C RANGE = 0 TO REFIN –60 70 THD (dB) –75 65 TA = 25°C RANGE = 0 TO REFIN –85 100 INPUT FREQUENCY (kHz) 03088-005 0 AVDD = VDRIVE = 2.7V AVDD = VDRIVE = 3.6V –80 fSAMPLE = 200kSPS 60 –70 –90 10 AVDD = VDRIVE = 4.75V AVDD = VDRIVE = 5.25V 100 INPUT FREQUENCY (kHz) Figure 5. SINAD vs. Analog Input Frequency for Various Supply Voltages at 200 kSPS 03088-007 SINAD (dB) –65 AVDD = VDRIVE = 3.6V AVDD = VDRIVE = 2.7V Figure 7. THD vs. Analog Input Frequency for Various Supply Voltages at 200 kSPS Rev. D | Page 10 of 28 Data Sheet –55 AD7927 fSAMPLE = 200kSPS TA = 25°C AVDD = 5.25V RANGE = 0 TO REFIN –65 0.6 RIN = 1000Ω –75 –80 RIN = 100Ω RIN = 10Ω –85 0.4 0.2 0 –0.2 –0.4 –0.6 RIN = 50Ω 10 100 INPUT FREQUENCY (kHz) 03088-008 –90 –95 AVDD = VDRIVE = 5V TA = 25°C 0.8 Figure 8. THD vs. Analog Input Frequency for Various Source Impedances –0.8 –1.0 0 512 1024 1536 2048 2560 CODE Figure 10. Typical DNL 1.0 AVDD = VDRIVE = 5V TA = 25°C 0.8 0.6 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0 512 1024 1536 2560 2048 CODE 3072 3584 4096 03088-009 INL ERROR (LSB) 0.4 Figure 9. Typical INL Rev. D | Page 11 of 28 3072 3584 4096 03088-010 THD (dB) –70 1.0 DNL ERROR (LSB) –60 AD7927 Data Sheet CONTROL REGISTER The control register on the AD7927 is a 12-bit, write-only register. Data is loaded from the DIN pin of the AD7927 on the falling edge of SCLK. The data is transferred on the DIN line at the same time that the conversion result is read from the part. The data transferred on the DIN line corresponds to the AD7927 configuration for the next conversion. This requires 16 serial clocks for every data transfer. Only the information provided on the first 12 falling clock edges (after CS falling edge) is loaded to the control register. MSB denotes the first bit in the data stream. The bit functions are outlined in Table 5. Table 5. Control Register Bit Functions MSB WRITE SEQ DONTC ADD2 ADD1 ADD0 PM1 PM0 SHADOW DONTC RANGE LSB CODING Table 6. Control Register Bit Function Description Bit 11 Mnemonic WRITE 10 SEQ 9 8 to 6 DONTC ADD2 to ADD0 5, 4 3 PM1, PM0 SHADOW 2 1 DONTC RANGE 0 CODING Description The value written to this bit of the control register determines whether the following 11 bits are loaded to the control register. If this bit is a 1, the following 11 bits are written to the control register; if it is a 0, then the remaining 11 bits are not loaded to the control register and it remains unchanged. The SEQ bit in the control register is used in conjunction with the SHADOW bit to control the use of the sequencer function and access the shadow register (see Table 10). Don’t care. These three address bits are loaded at the end of the present conversion and select which analog input channel is to be converted in the next serial transfer, or they may select the final channel in a consecutive sequence as described in Table 9. The selected input channel is decoded as shown in Table 7. The address bits corresponding to the conversion result are also output on DOUT prior to the 12 bits of data (see the Serial Interface section). The next channel to be converted on is selected by the mux on the 14th SCLK falling edge. Power Management Bits. These two bits decode the mode of operation of the AD7927 as shown in Table 8. The SHADOW bit in the control register is used in conjunction with the SEQ bit to control the use of the sequencer function and access the shadow register (see Table 10). Don’t care. This bit selects the analog input range to be used on the AD7927. If it is set to 0, the analog input range extends from 0 V to 2 × REFIN. If it is set to 1, the analog input range extends from 0 V to REFIN (for the next conversion). For the 0 V to 2 × REFIN range, AVDD = 4.75 V to 5.25 V. This bit selects the type of output coding the AD7927 uses for the conversion result. If this bit is set to 0, the output coding for the part is twos complement. If this bit is set to 1, the output coding from the part is straight binary (for the next conversion). Table 7. Channel Selection ADD2 0 0 0 0 1 1 1 1 ADD1 0 0 1 1 0 0 1 1 ADD0 0 1 0 1 0 1 0 1 Analog Input Channel VIN0 VIN1 VIN2 VIN3 VIN4 VIN5 VIN6 VIN7 Table 8. Power Mode Selection PM1 1 PM0 1 1 0 0 1 0 0 Mode Normal Operation. In this mode, the AD7927 remains in full power mode, regardless of the status of any of the logic inputs. This mode allows the fastest possible throughput rate from the AD7927. Full Shutdown. In this mode, the AD7927 is in full shutdown mode with all circuitry on the AD7927 powering down. The AD7927 retains the information in the control register while in full shutdown. The part remains in full shutdown until these bits are changed. Auto Shutdown. In this mode, the AD7927 automatically enters full shutdown mode at the end of each conversion when the control register is updated. Wake-up time from full shutdown is 1 μs and the user should ensure that 1 μs has elapsed before attempting to perform a valid conversion on the part in this mode. Invalid Selection. This configuration is not allowed. Rev. D | Page 12 of 28 Data Sheet AD7927 SEQUENCER OPERATION The configuration of the SEQ and SHADOW bits in the control register allows the user to select a particular mode of operation of the sequencer function. Table 9 outlines the four modes of operation of the sequencer. Table 9. Sequence Selection SEQ 0 SHADOW 0 0 1 1 0 1 1 Sequence Type This configuration means that the sequence function is not used. The analog input channel selected for each individual conversion is determined by the contents of the channel address bits, ADD0 through ADD2, in each prior write operation. This mode of operation reflects the traditional operation of a multichannel ADC, without the sequencer function being used, where each write to the AD7927 selects the next channel for conversion (see Figure 11). This configuration selects the shadow register for programming. The following write operation loads the contents of the shadow register. This programs the sequence of channels converted on continuously with each successive valid CS falling edge (see the Shadow Register section, Table 10, and Figure 12). The channels selected need not be consecutive. If the SEQ and SHADOW bits are set in this way, the sequence function is not interrupted upon completion of the WRITE operation. This allows other bits in the control register to be altered between conversions while in a sequence, without terminating the cycle. This configuration is used in conjunction with the channel address bits, ADD2 to ADD0, to program continuous conversions on a consecutive sequence of channels from Channel 0 to a selected final channel as determined by the channel address bits in the control register (see Figure 13). Rev. D | Page 13 of 28 AD7927 Data Sheet SHADOW REGISTER Table 10. Shadow Register Bit Functions VIN1 VIN2 VIN3 VIN4 VIN5 VIN6 VIN7 --------------------------------SEQUENCE ONE-------------------------------- The shadow register on the AD7927 is a 16-bit, write-only register. Data is loaded from the DIN pin of the AD7927 on the falling edge of SCLK. The data is transferred on the DIN line at the same time that a conversion result is read from the part. This requires 16 serial clock falling edges for the data transfer. The information is clocked into the shadow register, provided that the SEQ and SHADOW bits were set to 0, 1, respectively, in the previous write to the control register. MSB denotes the first bit in the data stream. Each bit represents an analog input from Channel 0 to Channel 7. Through programming the shadow register, two sequences of channels may be selected, through which the AD7927 cycles with each consecutive conversion after the write to the shadow register. Sequence One is performed first and then Sequence Two. If the user does not wish to perform a second sequence option, then all 0s must be written to the last eight LSBs of the shadow register. To select a sequence of channels, the associated channel bit must be set for each analog input. The AD7927 continuously cycles through the selected channels in ascending order, beginning with the lowest channel, until a write operation occurs (that is, the WRITE bit is set to 1) with the SEQ and SHADOW bits configured in any way except 1, 0 (see Table 9). The bit functions are outlined in Table 10. POWER-ON VIN0 VIN1 VIN2 VIN3 VIN4 POWER-ON DUMMY CONVERSION DIN = ALL 1s CS DIN: WRITE TO CONTROL REGISTER, WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT CHANNEL A2 TO CHANNEL A0 FOR CONVERSION. SEQ = 0, SHADOW = 1 DOUT: CONVERSION RESULT FROM PREVIOUSLY SELECTED CHANNEL A2 TO CHANNEL A0. DIN: WRITE TO SHADOW REGISTER, SELECTING WHICH CHANNELS TO CONVERT ON; CHANNELS SELECTED NEED NOT BE CONSECUTIVE CHANNELS WRITE BIT = 0 CS DOUT: CONVERSION RESULT FROM PREVIOUSLY SELECTED CHANNEL A2 TO CHANNEL A0. CONTINUOUSLY CONVERTS ON THE SELECTED SEQUENCE OF CHANNELS WRITE BIT = 0 WRITE BIT = 0 WRITE BIT = 1, DIN: WRITE TO CONTROL REGISTER, SEQ = SHADOW = 0 WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT CHANNEL A2 TO CHANNEL A0 FOR CONVERSION. SEQ = SHADOW = 0 Figure 11. SEQ Bit = 0, SHADOW Bit = 0 Flowchart WRITE BIT = 1, SEQ = 1 SHADOW = 0 CONTINUOUSLY CONVERTS ON THE SELECTED SEQUENCE OF CHANNELS BUT ALLOWS RANGE, CODING, AND SO ON, TO CHANGE IN THE CONTROL REGISTER WITHOUT INTERRUPTING THE SEQUENCE, PROVIDED SEQ = 1, SHADOW = 0 WRITE BIT = 1, SEQ = 1, SHADOW = 0 03088-011 CS LSB VIN7 Figure 12 shows how to program the AD7927 to continuously convert on a particular sequence of channels. To exit this mode of operation and revert back to the traditional mode of operation of a multichannel ADC (as outlined in Figure 11), ensure that the WRITE bit = 1 and the SEQ = SHADOW = 0 on the next serial transfer. Figure 13 shows how a sequence of consecutive channels can be converted on without having to program the shadow register or write to the part on each serial transfer. Again, to exit this mode of operation and revert back to the traditional mode of operation of a multichannel ADC (as outlined in Figure 11), ensure the WRITE bit = 1 and the SEQ = SHADOW = 0 on the next serial transfer. DUMMY CONVERSION DIN = ALL 1s CS VIN6 --------------------------------SEQUENCE TWO-------------------------------- CS DIN: WRITE TO CONTROL REGISTER, WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT CHANNEL A2 TO CHANNEL A0 FOR CONVERSION. SEQ = SHADOW = 0 VIN5 03088-012 MSB VIN0 Figure 12. SEQ and SHADOW Conversion Flowchart to Continuously Convert a Sequence of Channels Figure 11 reflects the traditional operation of a multichannel ADC, where each serial transfer selects the next channel for conversion. In this mode of operation, the sequencer function is not used. Rev. D | Page 14 of 28 Data Sheet AD7927 POWER-ON CONVERTER OPERATION The AD7927 is a 12-bit successive approximation ADC based around a capacitive DAC. The AD7927 can convert analog input signals in the range 0 V to REFIN or 0 V to 2 × REFIN. Figure 14 and Figure 15 show simplified schematics of the ADC. The ADC is comprised of control logic, SAR, and a capacitive DAC that are used to add and subtract fixed amounts of charge from the sampling capacitor to bring the comparator back into a balanced condition. Figure 14 shows the ADC during its acquisition phase. SW2 is closed and SW1 is in Position A. The comparator is held in a balanced condition and the sampling capacitor acquires the signal on the selected VIN channel. DUMMY CONVERSION DIN = ALL 1s CS DIN: WRITE TO CONTROL REGISTER, WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT CHANNEL A2 TO CHANNEL A0 FOR CONVERSION. SEQ = 1, SHADOW = 1 DOUT: CONVERSION RESULT FROM CHANNEL 0 CS CONTINUOUSLY CONVERTS ON A CONSECUTIVE SEQUENCE OF CHANNELS FROM CHANNEL 0 UP TO AND INCLUDING THE PREVIOUSLY SELECTED A2 TO CHANNEL A0 IN THE CONTROL REGISTER WRITE BIT = 0 CAPACITIVE DAC A SW1 The AD7927 provides the user with an on-chip, track-and-hold ADC and a serial interface housed in a 20-lead TSSOP. The AD7927 has eight single-ended input channels with a channel sequencer, allowing the user to select a channel sequence through which the ADC can cycle with each consecutive CS falling edge. The serial clock input accesses data from the part, controls the transfer of data written to the ADC, and provides the clock source for the successive approximation ADC. The analog input range for the AD7927 is 0 V to REFIN or 0 V to 2 × REFIN, depending on the status of Bit 1 in the control register. For the 0 to 2 × REFIN range, the part must be operated from a 4.75 V to 5.25 V supply. The AD7927 provides flexible power management options to allow the user to achieve the best power performance for a given throughput rate. These options are selected by programming the power management bits, PM1 and PM0, in the control register. CONTROL LOGIC SW2 COMPARATOR AGND Figure 14. ADC Acquisition Phase When the ADC starts a conversion (see Figure 15), SW2 opens and SW1 moves to Position B, causing the comparator to become unbalanced. The control logic and the capacitive DAC are used to add and subtract fixed amounts of charge balanced condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. Figure 17 and Figure 18 show the ADC transfer functions. CAPACITIVE DAC VIN0 A SW1 4kΩ B VIN7 CONTROL LOGIC SW2 COMPARATOR AGND 03088-015 The AD7927 is a high speed, 8-channel, 12-bit, single-supply ADC. The part can be operated from a 2.7 V to 5.25 V supply. When operated from either a 5 V or 3 V supply, the AD7927 is capable of throughput rates of 200 kSPS. The conversion time may be as short as 800 ns when provided with a 20 MHz clock. B VIN7 Figure 13. SEQ and SHADOW Conversion Flowchart to Convert a Sequence of Consecutive Channels CIRCUIT INFORMATION 4kΩ 03088-014 VIN0 03088-013 CS CONTINUOUSLY CONVERTS ON THE SELECTED SEQUENCE OF CHANNELS BUT ALLOWS RANGE, CODING AND SO ON, TO CHANGE IN THE CONTROL REGISTER WITHOUT INTERRUPTING WRITE BIT = 1, THE SEQUENCE, PROVIDED SEQ = 1, SHADOW = 0 SEQ = 1, SHADOW = 0 Figure 15. ADC Conversion Phase ANALOG INPUT Figure 16 shows an equivalent circuit of the analog input structure of the AD7927. The two diodes, D1 and D2, provide ESD protection for the analog inputs. Care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 300 mV. This causes these diodes to become forward biased and start conducting current into the substrate. 10 mA is the maximum current these diodes can conduct without causing irreversible damage to the part. Capacitor C1, in Figure 16 is typically about 4 pF and can primarily be attributed to pin capacitance. The Resistor R1 is a lumped component made up of the on resistance of a switch (track-and-hold switch) and also includes the on resistance of the input multiplexer. The total resistance is typically about 400 Ω. The capacitor, C2, is the ADC sampling capacitor and has a capacitance of 30 pF typically. Rev. D | Page 15 of 28 AD7927 Data Sheet 111…111 111…110 • • 111…000 • 011…111 • • 000…010 000…001 000…000 0V When no amplifier is used to drive the analog input, limit the source impedance to low values. The maximum source impedance depends on the amount of THD that can be tolerated. The THD increases as the source impedance increases, and performance degrades (see Figure 8). R1 CONVERSION PHASE: SWITCH OPEN TRACK PHASE: SWITCH CLOSED Figure 16. Equivalent Analog Input Circuit ADC TRANSFER FUNCTION 011…111 011…110 • • 000…001 000…000 111…111 • • 100…010 100…001 100…000 1LSB = 2 × VREF /4096 +VREF – 1LSB –VREF + 1LSB VREF – 1LSB ANALOG INPUT The output coding of the AD7927 is either straight binary or twos complement, depending on the status of the LSB in the control register. The designed code transitions occur at successive LSB values (that is, 1 LSB, 2 LSBs, and so forth). The LSB size is REFIN/4096 for the AD7927. The ideal transfer characteristic for the AD7927 when straight binary coding is selected is shown in Figure 17, and the ideal transfer characteristic for the AD7927 when twos complement coding is selected is shown in Figure 18. Figure 18. Twos Complement Transfer Characteristic with REFIN ± REFIN Input Range HANDLING BIPOLAR INPUT SIGNALS Figure 19 shows how useful the combination of the 2 × REFIN input range and the twos complement output coding scheme is for handling bipolar input signals. If the bipolar input signal is biased about REFIN and twos complement output coding is selected, then REFIN becomes the zero code point, −REFIN is negative full scale and +REFIN becomes positive full scale, with a dynamic range of 2 × REFIN. VDD VREF 0.1µF AVDD VDD VDRIVE R4 AD7927 R3 0V V VIN0 R2 R1 R1 = R2 = R3 = R4 DOUT DSP/ MICROPROCESSOR TWOS COMPLEMENT VIN7 +REFIN Rev. D | Page 16 of 28 011…111 000…000 REFIN –REFIN Figure 19. Handling Bipolar Signals (= 2 × REFIN) (= 0V) 100…000 03088-019 REFIN V 03088-018 D2 C2 30pF ADC CODE C1 4pF +VREF – 1LSB ANALOG INPUT Figure 17. Straight Binary Transfer Characteristic 03088-016 D1 1LSB NOTES VREF IS EITHER REFIN OR 2 × REFIN. AVDD VIN 1LSB = VREF /4096 03088-017 For ac applications, removing high frequency components from the analog input signal is recommended by use of an RC lowpass filter on the relevant analog input pin. In applications where harmonic distortion and signal-to-noise ratio are critical, the analog input should be driven from a low impedance source. Large source impedances significantly affect the ac performance of the ADC. This may necessitate the use of an input buffer amplifier. The choice of the op amp is a function of the particular application. Data Sheet AD7927 TYPICAL CONNECTION DIAGRAM Figure 20 shows a typical connection diagram for the AD7927. In this setup, the AGND pin is connected to the analog ground plane of the system. In Figure 20, REFIN is connected to a decoupled 2.5 V supply from a reference source, the AD780, to provide an analog input range of 0 V to 2.5 V (if the RANGE bit is 1) or 0 V to 5 V (if the RANGE bit is 0). Although the AD7927 is connected to a AVDD of 5 V, the serial interface is connected to a 3 V microprocessor. The VDRIVE pin of the AD7927 is connected to the same 3 V supply of the microprocessor to allow a 3 V logic interface (see the Digital Inputs section). The conversion result is output in a 16-bit word. This 16-bit data stream consists of one leading zero, three address bits indicating which channel the conversion result corresponds to, followed by the 12 bits of conversion data. For applications where power consumption is of concern, the power-down modes should be used between conversions or bursts of several conversions to improve power performance (see the Modes of Operation section). AVDD 0.1µF SCLK DOUT AD7927 AGND SERIAL INTERFACE CS VDRIVE DIN REFIN 2.5V 0.1µF 10µF AD780 NOTES ALL UNUSED INPUT CHANNELS SHOULD BE CONNECTED TO AGND. 3V SUPPLY 03088-020 0V TO REFIN VIN0 • • • • • VIN7 5V SUPPLY 10µF MICROCONTROLLER/ MICROPROCESSOR 0.1µF Figure 20. Typical Connection Diagram ANALOG INPUT SELECTION Any one of eight analog input channels may be selected for conversion by programming the multiplexer with the address bits (ADD2 though ADD0) in the control register. The channel configurations are shown in Table 7. The AD7927 may also be configured to automatically cycle through a number of channels as selected. The sequencer feature is accessed via the SEQ and SHADOW bits in the control register (see Table 9). The AD7927 can be programmed to continuously convert on a selection of channels in ascending order. The analog input channels to be converted on are selected through programming the relevant bits in the shadow register (see Table 10). The next serial transfer then acts on the sequence programmed by executing a conversion on the lowest channel in the selection. The next serial transfer results in the conversion on the next highest channel in the sequence, and so on. It is not necessary to write to the control register once a sequencer operation has been initiated. The WRITE bit must be set to zero or the DIN line tied low to ensure that the control register is not accidentally overwritten, or the sequence operation interrupted. If the control register is written to at any time during the sequence, the user must ensure that the SEQ and SHADOW bits are set to 1, 0, respectively to avoid interrupting the automatic conversion sequence. This pattern continues until such time as the AD7927 is written to and the SEQ and SHADOW bits are configured with any bit combination except 1, 0. On completion of the sequence, the AD7927 sequencer returns to the first selected channel in the shadow register and commence the sequence again. Rather than selecting a particular sequence of channels, a number of consecutive channels beginning with Channel 0 may also be programmed via the control register alone without needing to write to the shadow register. This is possible if the SEQ and SHADOW bits are set to 1, 1, respectively. The channel address bits, ADD2 through ADD0, then determine the final channel in the consecutive sequence. The next conversion is on Channel 0, then Channel 1, and so on until the channel selected via the Address Bit ADD2 through Address Bit ADD0 is reached. The cycle begins again on the next serial transfer provided the WRITE bit is set to low, or if high, that the SEQ and SHADOW bits are set to 1, 0, respectively; then the ADC continues its preprogrammed automatic sequence uninterrupted. Regardless of which channel selection method is used, the 16-bit word output from the AD7927 during each conversion always contains one leading zero, three channel address bits that the conversion result corresponds to, followed by the 12-bit conversion result (see the Serial Interface section). DIGITAL INPUTS The digital inputs applied to the AD7927 are not limited by the maximum ratings that limit the analog inputs. Instead, the digital inputs applied can go to 7 V and are not restricted by the AVDD + 0.3 V limit as on the analog inputs. Another advantage of SCLK, DIN, and CS not being restricted by the AVDD + 0.3 V limit is that possible power supply sequencing issues are avoided. If CS, DIN, or SCLK are applied before AVDD, there is no risk of latch-up as there would be on the analog inputs if a signal greater than 0.3 V was applied prior to AVDD. Rev. D | Page 17 of 28 AD7927 Data Sheet VDRIVE THE REFERENCE The AD7927 also has the VDRIVE feature. VDRIVE controls the voltage at which the serial interface operates. VDRIVE allows the ADC to easily interface to both 3 V and 5 V processors. For example, if the AD7927 were operated with an AVDD of 5 V, the VDRIVE pin could be powered from a 3 V supply. The AD7927 has a larger dynamic range with an AVDD of 5 V while still being able to interface to 3 V processors. Take care to ensure VDRIVE does not exceed AVDD by more than 0.3 V (see the Absolute Maximum Ratings section). An external reference source should be used to supply the 2.5 V reference to the AD7927. Errors in the reference source result in gain errors in the AD7927 transfer function and add to the specified full-scale errors of the part. A capacitor of at least 0.1 μF should be placed on the REFIN pin. Suitable reference sources for the AD7927 include the AD780, REF192, and the AD1582. If 2.5 V is applied to the REFIN pin, the analog input range can be either 0 V to 2.5 V or 0 V to 5 V, depending on the setting of the RANGE bit in the control register. Rev. D | Page 18 of 28 Data Sheet AD7927 MODES OF OPERATION For specified performance, the throughput rate should not exceed 200 kSPS, which means there should be no less than 5 μs between consecutive falling edges of CS when converting. The actual frequency of SCLK used determines the duration of the conversion within this 5 μs cycle; however, once a conversion is complete and CS has returned high, a minimum of the quiet time, tQUIET, must elapse before bringing CS low again to initiate another conversion. The AD7927 has a number of different modes of operation, which are designed to provide flexible power management options. These options can be chosen to optimize the power dissipation/throughput rate ratio for differing application requirements. The mode of operation of the AD7927 is controlled by the power management bits, PM1 and PM0, in the control register, as detailed in Table 8. When power supplies are first applied to the AD7927, care should be taken to ensure that the part is placed in the required mode of operation (see the Powering Up the AD7927 section). CS 12 16 1 LEADING ZERO + 3 CHANNEL IDENTIFIER BITS + CONVERSION RESULT DOUT DATA IN TO CONTROL REGISTER/ SHADOW REGISTER DIN NOTES 1. CONTROL REGISTER DATA IS LOADED ON FIRST 12 SCLK CYCLES. 2. SHADOW REGISTER DATA IS LOADED ON FIRST 16 SCLK CYCLES. The conversion is initiated on the falling edge of CS and the trackand-hold enters hold mode as described in the Serial Interface section. The data presented to the AD7927 on the DIN line during the first 12 clock cycles of the data transfer are loaded into the control register (provided the WRITE bit is 1). If data is to be written to the shadow register (SEQ = 0, SHADOW = 1 on the previous write), data presented on the DIN line during the first 16 SCLK cycles is loaded into the shadow register. The part remains fully powered up in normal mode at the end of the conversion as long as PM1 and PM0 are set to 1 in the write transfer during that conversion. To ensure continued operation in normal mode, PM1 and PM0 are both loaded with 1 on every data transfer. Sixteen serial clock cycles are required to complete the conversion and access the conversion result. The track-and-hold goes back into track on the 14th SCLK falling edge. CS may then idle high until the next conversion or may idle low until sometime prior to the next conversion (effectively idling CS low). 03088-021 This mode is intended for the fastest throughput rate performance because the user does not have to worry about any powerup times with the AD7927 remaining fully powered at all times. Figure 21 shows the general diagram of the operation of the AD7927 in this mode. Figure 21. Normal Mode Operation FULL SHUTDOWN (PM1 = 1, PM0 = 0) In this mode, all internal circuitry on the AD7927 is powered down. The part retains information in the control register during full shutdown. The AD7927 remains in full shutdown until the power management bits, PM1 and PM0, in the control register are changed. If a write to the control register occurs while the part is in full shutdown, with the power management bits changed to PM0 = CS rising edge. The track-and-hold that was in hold while the part was in full shutdown returns to track on the 14th SCLK falling edge. A full 16-SCLK transfer must occur to ensure the control register contents are updated; however, the DOUT line is not driven during this wake-up transfer. To ensure that the part is fully powered up, tPOWER UP should have elapsed before the next CS falling edge; otherwise, invalid data is read if a conversion is initiated before this time. Figure 22 shows the general diagram for this sequence. PART BEGINS TO POWER UP ON CS RISING EDGE AS PM1 = PM0 = 1 PART IS IN FULL SHUTDOWN 1 SCLK NORMAL MODE (PM1 = PM0 = 1) THE PART IS FULLY POWERED UP ONCE tPOWER UP HAS ELAPSED t12 CS 1 14 16 1 14 16 SCLK DOUT DATA IN TO CONTROL REGISTER/SHADOW REGISTER DATA IN TO CONTROL REGISTER TO KEEP THE PART IN NORMAL MODE, LOAD PM1 = PM0 = 1 IN CONTROL REGISTER CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS. PM1 = 1, PM0 = 1 Figure 22. Full Shutdown Mode Operation Rev. D | Page 19 of 28 03088-022 DIN CHANNEL IDENTIFIER BITS + CONVERSION RESULT AD7927 Data Sheet AUTO SHUTDOWN (PM1 = 0, PM0 = 1) Depending on the SCLK frequency used, this dummy transfer may affect the achievable throughput rate of the part, with every other data transfer being a valid conversion result. If, for example, the maximum SCLK frequency of 20 MHz was used, the auto shutdown mode could be used at the full throughput rate of 200 kSPS without affecting the throughput rate at all. Only a portion of the cycle time is taken up by the conversion time and the dummy transfer for wake-up. In this mode, the AD7927 automatically enters shutdown at the end of each conversion when the control register is updated. When the part is in shutdown, the track-and-hold is in hold mode. Figure 23 shows the general diagram of the operation of the AD7927 in this mode. In shutdown mode all internal circuitry on the AD7927 is powered down. The part retains information in the control register during shutdown. The AD7927 remains in shutdown until the next CS falling edge it receives. On this CS falling edge, the track-and-hold that was in hold while the part was in shutdown returns to track. Wake-up time from auto shutdown is 1 μs maximum, and the user should ensure that 1 μs has elapsed before attempting a valid conversion. When running the AD7927 with a 20 MHz clock, one dummy 16 SCLK transfer should be sufficient to ensure the part is fully powered up. During this dummy transfer, the contents of the control register should remain unchanged; therefore, the WRITE bit should be 0 on the DIN line. PART ENTERS SHUTDOWN ON CS RISING EDGE AS PM1 = 0, PM0 = 1 PART BEGINS TO POWER UP ON CS FALLING EDGE CS DOUT DIN PART IS FULLY POWERED UP PART ENTERS SHUTDOWN ON CS RISING EDGE AS PM1 = 0, PM0 = 1 DUMMY CONVERSION 1 12 16 CHANNEL IDENTIFIER BITS + CONVERSION RESU LT 1 12 16 INVALID DATA 12 16 CHANNEL IDENTIFIER BITS + CONVERSION RESU LT DATA INTO CONTROL/SHADOW REGISTER DATA IN TO CONTROL/SHADOW REGISTER CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS, PM1 = 0, PM0 = 1 1 CONTROL REGISTER SHOULD NOT CHANGE, WRITE BIT = 0 Figure 23. Auto Shutdown Mode Operation Rev. D | Page 20 of 28 TO KEEP PART IN THIS MODE, LOAD PM1 = 0, PM0 = 1 IN CONTROL REGISTER OR SET WRITE BIT = 0 03088-023 SCLK In this mode, the power consumption of the part is greatly reduced with the part entering shutdown at the end of each conversion. When the control register is programmed to move into auto shutdown, it does so at the end of the conversion. The user can move the ADC in and out of the low power state by controlling the CS signal. Data Sheet AD7927 CORRECT VALUE IN CONTROL REGISTER, VALID DATA FROM NEXT CONVERSION, USER CAN WRITE TO SHADOW REGISTER IN NEXT CONVERSION CS DOUT 12 DUMMY CONVERSION 16 1 12 INVALID DATA 16 1 16 12 INVALID DATA INVALID DATA DATA INTO CONTROL REGISTER DIN 03088-024 SCLK DUMMY CONVERSION 1 CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCK EDGES KEEP DIN LINE TIED HIGH FOR FIRST TWO DUMMY CONVERSIONS Figure 24. Three-Dummy-Conversions to Place AD7927 into the Required Operating Mode After Power Supplies Are Applied The three-dummy-conversion operation outlined in Figure 24 must be performed to place the part into the auto shutdown mode. The first two conversions of this dummy cycle operation are performed with the DIN line tied high, and for the third conversion of the dummy cycle operation, the user should write the desired control register configuration to the AD7927 to place the part into the auto shutdown mode. On the third CS rising edge after the supplies are applied, the control register contains the correct information and valid data results from the next conversion. Therefore, to ensure the part is placed into the correct operating mode, when supplies are first applied to the AD7927, the user must first issue two serial write operations with the DIN line tied high, and on the third conversion cycle the user can then write to the control register to place to part into any of the operating modes. The user should not write to the shadow register until the fourth conversion cycle after the supplies are applied to the ADC, to guarantee the control register contains the correct data. If the user wishes to place the part into either the normal or full shutdown mode, the second dummy cycle with DIN tied high can be omitted from the three-dummy-conversion operation outlined in Figure 24. POWER VS. THROUGHPUT RATE In auto shutdown mode, the average power consumption of the ADC may be reduced at any given throughput rate. The power saving depends on the SCLK frequency used, that is, conversion time. In some cases where the conversion time is quite a proportion of the cycle time, the throughput rate needs to be reduced to take advantage of the power-down modes. Assuming a 20 MHz SCLK is used, the conversion time is 800 ns, but the cycle time is 5 μs when the sampling rate is at a For example, if the AD7927 is operated in a continuous sampling mode, with a throughput rate of 200 kSPS and an SCLK of 20 MHz (AVDD = 5 V), and the device is placed in auto shutdown mode, that is, if PM1 = 0 and PM0 = 1, then the power consumption is calculated as follows. The maximum power dissipation during the conversion time is 13.5 mW (IDD = 2.7 mA maximum, AVDD = 5 V). If the powerup time from auto shutdown is 1 μs and the remaining conversion time is another cycle, that is, 800 ns, the AD7927 can be said to dissipate 13.5 mW for 1.8 μs during each conversion cycle. For the remainder of the conversion cycle, 3.2 μs, the part remains in shutdown. The AD7927 can be said to dissipate 2.5 μW for the remaining 3.2 μs of the conversion cycle. If the throughput rate is 200 kSPS, the cycle time is 5 μs and the average power dissipated during each cycle is (1.8/5) × (13.5 mW) + (3.2/5) × (2.5 μW) = 4.8616 mW. Figure 25 shows the maximum power vs. throughput rate when using the auto shutdown mode with 3 V and 5 V supplies. 10 AVDD = 5V AVDD = 3V 1 Rev. D | Page 21 of 28 0.1 0.01 0 20 40 60 80 100 120 140 THROUGHPUT (kSPS) 160 Figure 25. Power vs. Throughput Rate 180 200 03088-025 When supplies are first applied to the AD7927, the ADC may power up in any of the operating modes of the part. To ensure that the part is placed into the required operating mode, the user should perform a dummy cycle operation as outlined in Figure 24. maximum of 200 kSPS. If the AD7927 is placed into shutdown for the remainder of the cycle time, then on average far less power is consumed in every cycle compared to leaving the device in normal mode. Furthermore, Figure 25 shows how as the throughput rate is reduced, the part remains in its shutdown longer and the average power consumption drops accordingly over time. POWER (mW) POWERING UP THE AD7927 AD7927 Data Sheet SERIAL INTERFACE information to the shadow register takes place on all 16 SCLK falling edges in the next serial transfer as shown for example on the AD7927 in Figure 27. Two sequence options can be programmed in the shadow register. If the user does not want to program a second sequence, then the eight LSBs should be filled with zeros. The shadow register is updated upon the rising edge of CS and the track-and-hold begins to track the first channel selected in the sequence. Figure 26 shows the detailed timing diagram for serial interfacing to the AD7927. The serial clock provides the conversion clock and also controls the transfer of information to and from the AD7927 during each conversion. The CS signal initiates the data transfer and conversion process. The falling edge of CS puts the track-and-hold into hold mode and takes the bus out of three-state; the analog input is sampled at this point. The conversion is also initiated at this point and requires 16 SCLK cycles to complete. The track-and-hold goes back into track on the 14th SCLK falling edge as shown in Figure 26 at Point B, except when the write is to the shadow register, in which case the track-and-hold does not return to track until the rising edge of CS, that is, Point C in Figure 27. On the 16th SCLK falling edge the DOUT line goes back into three-state. If the rising edge of CS occurs before 16 SCLKs have elapsed, the conversion is terminated and the DOUT line goes back into three-state and the control register is not be updated; otherwise DOUT returns to three-state on the 16th SCLK falling edge, as shown in Figure 26. Sixteen serial clock cycles are required to perform the conversion process and to access data from the AD7927. For the AD7927, the 12 bits of data are preceded by a leading zero and the three-channel address bits (ADD2 to ADD0) identifying which channel the result corresponds to. CS going low provides the leading zero to be read in by the microcontroller or DSP. The three remaining address bits and data bits are then clocked out by subsequent SCLK falling edges beginning with the first address bit (ADD2) thus the first falling clock edge on the serial clock has a leading zero provided and also clocks out Address Bit ADD2. The final bit in the data transfer is valid on the 16th falling edge, having been clocked out on the previous (15th) falling edge. The 16-bit word read from the AD7927 always contains a leading zero and three-channel address bits that the conversion result corresponds to, followed by the 12-bit conversion result. WRITING BETWEEN CONVERSIONS As outlined in the Modes of Operation section, no less than 5 μs should be left between consecutive valid conversions. However, there is one case where this does not necessarily mean that at least 5 μs should always be left between CS falling edges. Consider the prior to a valid conversion. The user must write to the part to tell it to power up before it can convert successfully. Once the serial write to power up has finished, it may be desirable to perform the conversion as soon as possible and not have to wait a further 5 μs before bringing CS low for the conversion. In this case, as long as there is a minimum of 5 μs between each valid conversion, then only the quiet time between the CS rising edge at the end of the write to power up and the next CS falling edge for a valid conversion needs to be met (see Figure 28). Note that when writing to the AD7927 between these valid conversions, the DOUT line is not driven during the extra write operation, as shown in Figure 28. It is critical that an extra write operation as outlined previously is never issued between valid conversions when the AD7927 is executing through a sequence function, as the falling edge of CS in the extra write would move the mux on to the next channel in the sequence. This means when the next valid conversion takes place, a channel result would have been missed. Writing of information to the control register takes place on the first 12 falling edges of SCLK in a data transfer, assuming the MSB (that is, the WRITE bit) has been set to 1. If the control register is programmed to use the shadow register, then the writing of CS SCLK 1 2 3 4 t3 DOUT DIN THREESTATE ZERO WRITE 5 13 ADD1 ADD0 3 IDENTIFICATION BITS t9 SEQ DONTC ADD2 14 DB11 DB10 15 16 t5 t7 t4 ADD2 tQUIET B t11 t8 DB2 DB1 DB0 t10 ADD1 ADD0 DONTC Figure 26. Serial Interface Timing Diagram Rev. D | Page 22 of 28 DONTC DONTC THREE-STATE 03088-026 tCONVERT t6 t2 Data Sheet AD7927 C CS tCONVERT t6 t2 2 3 4 t3 DOUT DIN 13 VIN1 VIN2 14 DB11 15 t5 t7 t4 ADD2 ADD1 ADD0 THREE3 IDENTIFICATION BITS STATE t9 ZERO VIN0 5 DB10 DB2 16 t11 t8 DB1 DB0 THREE-STATE t10 VIN3 VIN4 VIN5 VIN5 SEQUENCE 1 VIN6 VIN7 SEQUENCE 2 Figure 27. Writing to Shadow Register Timing Diagram tCYCLE 5µs MINIMUM tQUIET MINIMUM CS 1 16 1 16 1 16 SCLK DOUT DIN VALID DATA VALID DATA POWER-UP Figure 28. General Timing Diagram Rev. D | Page 23 of 28 03088-027 1 03088-028 SCLK AD7927 Data Sheet MICROPROCESSOR INTERFACING The serial interface on the AD7927 allows the part to be directly connected to a range of many different microprocessors. This section explains how to interface the AD7927 with some of the more common microcontroller and DSP serial interface protocols. AD7927 TO TMS320C541 INVRFS = INVTFS = 1, active low frame signal CLKX DOUT CLKR DR DIN DT CS FSX SLEN = 1111, 16-bit data-words ISCLK = 1, internal serial clock TFSR = RFSR = 1, frame every word IRFS = 0 ITFS = 1 The connection diagram is shown in Figure 30. The ADSP-218x has the TFS and RFS of the SPORT0 tied together, with TFS set as an output and RFS set as an input. The DSP operates in alternate framing mode and the SPORT0 control register is set up as described. The frame synchronization signal generated on the TFS is tied to CS, and as with all signal processing applications equidistant sampling is necessary. However, in this example, the timer interrupt is used to control the sampling rate of the ADC, and under certain conditions, equidistant sampling may not be achieved. AD7927* SCLK DR DOUT RFS CS FSR TFS 03088-029 *ADDITIONAL PINS REMOVED FOR CLARITY. ADSP-218x* SCLK VDD VDRIVE DIN DT Figure 29. Interfacing to the TMS320C541 *ADDITIONAL PINS REMOVED FOR CLARITY. AD7927 TO ADSP-21xx VDD 03088-030 TMS320C541* SCLK VDRIVE TFSW = RFSW = 1, alternate framing DTYPE = 00, right justify data The serial interface on the TMS320C541 uses a continuous serial clock and frame synchronization signals to synchronize the data transfer operations with peripheral devices like the AD7927. The CS input allows easy interfacing between the TMS320C541 and the AD7927 without any glue logic required. The serial port of the TMS320C541 is set up to operate in burst mode with internal CLKX0 (TX serial clock on Serial Port 0) and FSX0 (TX frame sync from Serial Port 0). The serial port control register (SPC) must have the following setup: FO = 0, FSM = 1, MCM = 1, and TXM = 1. The connection diagram is shown in Figure 29. It should be noted that for signal processing applications, it is imperative that the frame synchronization signal from the TMS320C541 provides equidistant sampling. The VDRIVE pin of the AD7927 takes the same supply voltage as that of the TMS320C541. This allows the ADC to operate at a higher voltage than the serial interface, that is, TMS320C541, if necessary. AD7927* The SPORT0 control register should be set up as follows: Figure 30. Interfacing to the ADSP-218x The ADSP-21xx family of DSPs is interfaced directly to the AD7927 without any glue logic required. The VDRIVE pin of the AD7927 takes the same supply voltage as that of the ADSP-218x. This allows the ADC to operate at a higher voltage than the serial interface, that is, ADSP-218x, if necessary. The timer register, for instance, is loaded with a value that provides an interrupt at the required sample interval. When an interrupt is received, a value is transmitted with TFS or DT, (ADC control word). The TFS is used to control the RFS and therefore the reading of data. The frequency of the serial clock is set in the SCLKDIV register. When the instruction to transmit with TFS is given (that is, AX0 = TX0), the state of the SCLK is checked. The DSP waits until the SCLK has gone high, low, and high before transmission starts. If the timer and SCLK values are chosen such that the instruction to transmit occurs on or near the rising edge of SCLK, then the data may be transmitted or it may wait until the next clock edge. Rev. D | Page 24 of 28 Data Sheet AD7927 WL1 = 1 and WL0 = 0 in CRA. The FSP bit in the CRB should be set to 1 so the frame sync is negative. It should be noted that for signal processing applications, it is imperative that the frame synchronization signal from the DSP563xx provides equidistant sampling. In the example shown in Figure 31, the serial clock is taken from the ESSI so the SCK0 pin must be set as an output, SCKD = 1. The VDRIVE pin of the AD7927 takes the same supply voltage as that of the DSP563xx. This allows the ADC to operate at a higher voltage than the serial interface, that is, DSP563xx, if necessary. AD7927* AD7927 TO DSP563xx The connection diagram in Figure 31 shows how the AD7927 can be connected to the enhanced synchronous serial interface (ESSI) of the DSP563xx family of DSPs from Motorola. Each ESSI (two on board) is operated in synchronous mode (SYN bit in CRB = 1) with internally generated word length frame sync for both TX and RX (Bit FSL1 = 0 and Bit FSL0 = 0 in CRB). Normal operation of the ESSI is selected by making MOD = 0 in the CRB. Set the word length to 16 by setting bits VDRIVE DSP563xx* SCLK SCK DOUT SRD CS STD DIN SC2 *ADDITIONAL PINS REMOVED FOR CLARITY. Rev. D | Page 25 of 28 Figure 31. Interfacing to the DSP563xx VDD 03088-031 For example, if the ADSP-2189 had a 20 MHz crystal such that it had a master clock frequency of 40 MHz, then the master cycle time would be 25 ns. If the SCLKDIV register is loaded with the value of 3, then an SCLK of 5 MHz is obtained and eight master clock periods elapse for every one SCLK period. Depending on the throughput rate selected, if the timer registers are loaded with the value, of 803, for example, then 100.5 SCLKs occur between interrupts and subsequently between transmit instructions. This situation results in sampling that is not equidistant as the transmit instruction is occurring on a SCLK edge. If the number of SCLKs between interrupts is a whole integer figure of N, then equidistant sampling is implemented by the DSP. AD7927 Data Sheet APPLICATION HINTS GROUNDING AND LAYOUT The AD7927 has very good immunity to noise on the power supplies as can be seen in Figure 6. However, care should still be taken with regard to grounding and layout. The printed circuit board that houses the AD7927 should be designed such that the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of ground planes that can be separated easily. A minimum etch technique is generally best for ground planes as it gives the best shielding. All three AGND pins of the AD7927 should be sunk in the AGND plane. Digital and analog ground planes should be joined at only one place. If the AD7927 is in a system where multiple devices require an AGND to DGND connection, the connection should still be made at one point only, a star ground point that should be established as close as possible to the AD7927. Avoid running digital lines under the device as these couple noise onto the die. The analog ground plane should be allowed to run under the AD7927 to avoid noise coupling. The power supply lines to the AD7927 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals, like clocks, should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. A microstrip technique is by far the best, but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes while signals are placed on the solder side. Good decoupling is also important. All analog supplies should be decoupled with 10 μF tantalum in parallel with 0.1 μF capacitors to AGND. To achieve the best from these decoupling components, they must be placed as close as possible to the device, ideally right up against the device. The 0.1 μF capacitors should have low effective series resistance (ESR) and effective series inductance (ESI), such as the common ceramic types or surface mount types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Rev. D | Page 26 of 28 Data Sheet AD7927 OUTLINE DIMENSIONS 6.60 6.50 6.40 20 11 4.50 4.40 4.30 6.40 BSC 1 10 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 COPLANARITY 0.10 0.30 0.19 0.20 0.09 SEATING PLANE 0.75 0.60 0.45 8° 0° COMPLIANT TO JEDEC STANDARDS MO-153-AC Figure 32. 20-Lead Thin Shrink Small Outline Package [TSSOP] (RU-20) Dimensions shown in millimeters ORDERING GUIDE Model1, 2 AD7927BRU AD7927BRU-REEL AD7927BRUZ AD7927BRUZ-REEL AD7927BRUZ–REEL7 AD7927WYRUZ-REEL7 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +125°C Linearity Error (LSB)3 ±1 ±1 ±1 ±1 ±1 ±1 Package Description 20-Lead TSSOP 20-Lead TSSOP 20-Lead TSSOP 20-Lead TSSOP 20-Lead TSSOP 20-Lead TSSOP Package Option RU-20 RU-20 RU-20 RU-20 RU-20 RU-20 1 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. 3 Linearity error refers to integral linearity error. 2 AUTOMOTIVE PRODUCTS The AD7927W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. D | Page 27 of 28 AD7927 Data Sheet NOTES ©2003–2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03088-0-6/13(D) Rev. D | Page 28 of 28