AFBR-4526Z, AFBR-452BZ Plastic optical fiber duplex connector for AFBR-5972xZ Data Sheet Description Features The AFBR-452xZ duplex connectors are designed for use with Avago Technologies’ fast Ethernet transceiver AFBR5972xZ. The rugged design contains a latching mechanism for an increased retention force. The simple snaptogether concept saves the user labor and tool cost. • ULTEM Plastic Material (UL File #E121562) The connectors are made of a rugged, flame retardant plastic which is good for industrial and other harsh environments. The AFBR-452xZ duplex connectors are for use with Plastic Optical Fiber (POF) only. For termination of POF with AFBR-452xZ, we recommend to use the polishing kit AFBR-4594Z. • Available in two colors: black and blue • Suitable for 1mm diameter duplex plastic optical fiber (POF) • Latching mechanism for increased retention force • Easy installation of POF links with AFBR-5972xZ Applications • Industrial data links for factory automation and plant control • Intra-system links, board-to-board, rack-to-rack • Medical instruments • High voltage isolation Absolute maximum ratings Parameter Min Max Unit Note Storage and operating temperature -40 85 °C 1 Recommended operation temperature -40 85 °C 1 Installation temperature 0 70 °C 1 Unit Temp. [°C] Note Mechanical characteristics Parameter Min Typ. Retention force, connector to transceiver; latching button pressed 15 20 N 25 2 24 N 25 -40 to +85 2,3 Tensile force, connector to cable 90 N 2 Insertion force, connector to transceiver 20 N 2 Retention force, connector to transceiver; latching button NOT pressed 8 Max Notes: 1. Storage and operating temperatures refer to the ranges over which the connectors can be used when not subjected to mechanical stress. Installation temperature refers to the ranges over which connectors may be installed onto the fiber and over which connectors can be connected and disconnected from the trnasceiver. 2. Typical data at 25°C. 3. CAUTION - The latching mechanism release button should be pressed before attempting to disconnect the fiber. If the connector is pulled out of the transceiver without pressing the lever, damage will occur. Termination Guide for AFBR-452xZ Step-by-Step Plastic Cable Connectoring Instructions Step 2: Putting on the Connector The following step-by-step guide describes how to terminate plastic fiber optic cable. It is ideal for both field and factory installations. Connectors can be easily installed on cable ends with standard tools such as wire strippers and cutters. Place the connector on each end of the fiber, and slide the connector down until the fiber jacket stops it. The fiber should protrude no less than 1.5 mm (0.06 in) from the end of the connector. Finishing the cable is accomplished with the Avago Technologies AFBR-4594Z Polishing Kit, consisting of a three hole polishing fixture, 600 grit abrasive paper and 3 mm pink lapping film. The connector can be used immediately after polishing. Manually press connectors together. The connectors are secured when top halves latch into the ferrule halves. The following materials are needed for plastic fiber termination: 1. Plastic optical fiber cable (Example: HFBR-EUD500Z) 2. Wire cutters or scissors 3. 16 gauge wire stripper (Example: Ideal Stripmaster type 45-092) 4. AFBR-4594Z polishing kit 5. Duplex connectors AFBR-452xZ Step 1: Stripping the Fiber The zip cord structure of the duplex cable permits easy separation of the channels. The channels should be separated a minimum of 100 mm (4 in) to a maximum of 150 mm (6 in) back from the ends to permit connectoring, polishing and cable end flexibility. After cutting the cable to the desired length, strip off approximately 7 mm (0.3 in) of the outer jacket with the 16 gauge wire strippers. The separated duplex cable should be stripped to roughly equal lengths on each cable end. During insertion of the fiber into the connector, make sure that the orientation of the connector is correct (see next figure). So you make sure that the optical channels are connected correctly (Tx1 --> Rx2; Tx2 --> Rx1). Hinge Ok Untwisted fiber Not Ok 2 Step 3: Trimming and Polishing Any fiber in excess of 1.5 mm (0.06 in) protruding from the connector end should be cut off with wire cutters or scissors. Insert the connector fully into the polishing fixture with the trimmed fiber protruding from the bottom of the fixture. This plastic polishing fixture can be used to polish one or two simplex connectors or one duplex connector. Note: The four dots on the bottom of the polishing fixture are wear indicators. Replace the polishing fixture when any dot is no longer visible. Press the polishing tool down on the 600 grit abrasive paper. Polish the fiber using a figure eight pattern until the connector is flush with the bottom of the polishing fixture. Wipe the connector and fixture with a clean cloth or tissue. Step 4: Finishing Place the flush connector and polishing fixture on the dull side of the 3 μm pink lapping film and continue to polish the fiber in the same figure eight pattern for approximately 25 strokes. The fiber end should be flat, smooth and clean. Polishing kit AFBR-4594Z Note: Use of the pink lapping film fine polishing step results in up to 0,5 dB improvement in coupling performance of either a transmitter-receiver link or a bulkhead/splice over a 600 grit polish alone. This fine polish is comparable to the Avago Technologies factory polish. The fine polishing step may be omitted for short link lengths. 3 6.0 8.6 3.8 16.0 Package Dimensions 33.5 7.35 11.7 Part Number Connector Color AFBR-4526Z Black AFBR-452BZ Blue Note: Dimensions are in mm Ordering Guide for POF Cable AFBR - x x D 0 0 Cable Code R = Standard Attenuation POF E = Low Attenuation POF [1] Connector Code S = With AFBR-4526Z Black Connectors B = With AFBR-452BZ Blue Connectors D = With AFBR-4526Z/452BZ Connectors x Z RoHS Compliant Length Code (measured from connector tip to tip of connector) Maximum 500 meters (not in 1meter increments) X = 1 meters or 2 meters or 5 meters only. e.g 001 = 1 meters Channel Code D = Duplex Zipcord Cable Notes: 1. Standard (type = “R”) and Low Attenuation (type = “E”) cables comply with UL VW-1 flame retardant specification (UL file # E89328) 2. For other cable lengths please contact Avago representative For Example: HFBR-RSD002Z is a Standard attenuation, AFBR-4526Z Duplex connectors, 2 meters cable. Cable Length Tolerances The plastic cable length tolerances are: +10% / 0% For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2015 Avago Technologies. All rights reserved. AV02-2926EN - March 10, 2015