1.6X0.8mm SMD CHIP LED LAMP Part Number: APT1608LSYCK/J3-PRV Super Bright Yellow Features Description z 1.6mmX0.8mm SMT LED, 0.75mm thickness. The Super Bright Yellow device is based on light emitting z Low power consumption. diode chip made from AlGaInP. z Wide viewing angle. z Ideal for backlight and indicator. z Package: 2000pcs / reel . z Moisture sensitivity level : level 3. z Low current IF=2mA operating. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAN8389 REV NO: V.2B DATE: MAR/09/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014457 Selection Guide Part No. Dice APT1608LSYCK/J3-PRV Lens Type Super Bright Yellow (AlGaInP) Water Clear Viewing Angle [1] Iv (mcd) [2] @ 2mA Min. Typ. 2θ1/2 15 25 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Min. Symbol Parameter Device λpeak Peak Wavelength Super Bright Yellow λD [1] Dominant Wavelength Δλ1/2 Units Test Conditions 590 nm IF=2mA Super Bright Yellow 590 nm IF=2mA Spectral Line Half-width Super Bright Yellow 20 nm IF=2mA C Capacitance Super Bright Yellow 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Yellow 2.1 V IF=2mA IR Reverse Current Super Bright Yellow 10 uA VR=5V 1.5 Typ. 1.85 Max. Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Yellow Units Power dissipation 63 mW DC Forward Current 30 mA Peak Forward Current [1] 140 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAN8389 REV NO: V.2B DATE: MAR/09/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014457 Super Bright Yellow APT1608LSYCK/J3-PRV SPEC NO: DSAN8389 REV NO: V.2B DATE: MAR/09/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014457 APT1608LSYCK/J3-PRV Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAN8389 REV NO: V.2B DATE: MAR/09/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014457 PACKING & LABEL SPECIFICATIONS APT1608LSYCK/J3-PRV Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAN8389 REV NO: V.2B DATE: MAR/09/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014457