FERROXCUBE DATA SHEET E30/15/7 E cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube E cores and accessories E30/15/7 CORE SETS Effective core parameters SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 1.12 mm−1 Ve effective volume 4000 mm3 Ie effective length 67.0 mm Ae effective area 60.0 mm2 Amin minimum area 49.0 mm2 m mass of core half ≈ 11 g 0 −1.4 +1.0 19.5 0 0 7.2 −0.5 30.8 handbook, halfpage 9.7 R ≤ 0.5 +0.5 0 15 ±0.2 R1 7.3 0 −0.5 CBW032 Dimensions in mm. Fig.1 E30/15/7 core half. Core halves AL measured in combination with a non-gapped core half, clamping force for AL measurements 20 ±10 N, unless stated otherwise. GRADE 3C81 3C90 AL (nH) 100 ±5%(1) TOTAL AIR GAP (µm) µe TYPE NUMBER ≈ 89 ≈ 1100 E30/15/7-3C81-E100 160 ±5% ≈142 ≈ 580 E30/15/7-3C81-A160 250 ±5% ≈ 222 ≈ 330 E30/15/7-3C81-A250 315 ±5% ≈ 280 ≈ 240 E30/15/7-3C81-A315 400 ±8% ≈ 355 ≈ 180 E30/15/7-3C81-A400 630 ±15% ≈ 560 ≈ 100 E30/15/7-3C81-A630 2500 ±25% ≈ 2220 ≈0 ±5%(1) E30/15/7-3C81 ≈ 89 ≈ 1100 E30/15/7-3C90-E100 160 ±5% ≈142 ≈ 580 E30/15/7-3C90-A160 250 ±5% ≈ 222 ≈ 330 E30/15/7-3C90-A250 100 315 ±5% ≈ 280 ≈ 240 E30/15/7-3C90-A315 400 ±8% ≈ 355 ≈ 180 E30/15/7-3C90-A400 630 ±15% ≈ 560 ≈ 100 E30/15/7-3C90-A630 1900 ±25% ≈ 1690 ≈0 E30/15/7-3C90 3C91 2500 ±25% ≈ 2220 ≈0 E30/15/7-3C91 3C92 1400 ±25% ≈ 1250 ≈0 E30/15/7-3C92 3C94 1900 ±25% ≈ 1690 ≈0 E30/15/7-3C94 3C96 1600 ±25% ≈ 1420 ≈0 E30/15/7-3C96 2008 Sep 01 388 Ferroxcube E cores and accessories AL (nH) µe 100 ±5%(1) ≈ 89 GRADE 3F3 3F35 E30/15/7 TOTAL AIR GAP (µm) TYPE NUMBER ≈ 1100 E30/15/7-3F3-E100 160 ±5% ≈142 ≈ 580 E30/15/7-3F3-A160 250 ±5% ≈ 222 ≈ 330 E30/15/7-3F3-A250 315 ±5% ≈ 280 ≈ 240 E30/15/7-3F3-A315 400 ±8% ≈ 355 ≈ 180 E30/15/7-3F3-A400 630 ±15% ≈ 560 ≈ 100 E30/15/7-3F3-A630 1600 ±25% ≈1420 ≈0 E30/15/7-3F3 1250 ±25% ≈1110 ≈0 E30/15/7-3F35 Note 1. Measured in combination with an equal gapped core half, clamping force for AL measurements, 20 ±10 N. Core halves of high permeability grades Clamping force for AL measurements 20 ±10 N. AL (nH) GRADE AIR GAP (µm) µe TYPE NUMBER 3C11 3300 ±25% ≈ 2930 ≈0 E30/15/7-3C11 3E27 4100 ±25% ≈ 3640 ≈0 E30/15/7-3E27 Properties of core sets under power conditions B (mT) at CORE LOSS (W) at H = 250 A/m; f = 25 kHz; T = 100 °C f = 25 kHz; ˆ = 200 mT; B T = 100 °C 3C81 ≥320 3C90 ≥330 3C91 ≥320 − 3C92 ≥370 − ≤ 0.36 ≤ 2.0 − 3C94 ≥330 − ≤ 0.36 ≤ 2.0 − 3C96 ≥340 − ≤ 0.27 ≤ 1.6 − 3F3 ≥320 − ≤ 0.47 − ≤ 0.80 3F35 ≥300 − − − − GRADE f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C ≤ 0.82 − − − ≤ 0.45 ≤ 0.48 − − ≤ 0.27 (1) ≤ 1.6(1) − Properties of core sets under power conditions (continued) B (mT) at CORE LOSS (W) at H = 250 A/m; f = 25 kHz; T = 100 °C f = 500 kHz; ˆ = 50 mT; B T = 100 °C f = 500 kHz; ˆ = 100 mT; B T = 100 °C f = 1 MHz; ˆ = 30 mT; B T = 100 °C f = 3 MHz; ˆ = 10 mT; B T = 100 °C 3C96 ≥340 ≤ 1.5 − − − 3F3 ≥320 − − − − 3F35 ≥300 ≤ 0.54 ≤ 4.2 − − GRADE Note 1. Measured at 60 °C. 2008 Sep 01 389 Ferroxcube E cores and accessories E30/15/7 COIL FORMERS GENERAL DATA FOR E30/15/7 COIL FORMER WITHOUT PINS PARAMETER SPECIFICATION Coil former material polyamide (PA6.6), glass reinforced, flame retardant in accordance with “UL 94-HB” ; UL file number E41613(M) Maximum operating temperature 120 °C handbook, full pagewidth 20.1 max. 7.5 +0.1 0 9 0 −0.2 CBW033 17 min. 19.1 max. 19 Dimensions in mm. Fig.2 E30/15/7 coil former. WINDING DATA AND AREA PRODUCT FOR E30/15/7 COIL FORMER WITHOUT PINS (E) NUMBER OF SECTIONS WINDING AREA (mm2) MINIMUM WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm4) 1 80 17.0 56 4800 2008 Sep 01 390 TYPE NUMBER CP-E30/15/7-1S Ferroxcube E cores and accessories E30/15/7 GENERAL DATA FOR 10-PINS E30/15/7 COIL FORMER PARAMETER SPECIFICATION Coil former material phenolformaldehyde (PF), glass reinforced, flame retardant in accordance with “UL 94V-0” ; UL file number E167521(M) Pin material copper-tin alloy (CuSn), tin (Sn) plated Maximum operating temperature 180 °C, “IEC 60085”, class H Resistance to soldering heat “IEC 60068-2-20”, Part 2, Test Tb, method 1B: 350 °C, 3.5 s Solderability “IEC 60068-2-20”, Part 2, Test Ta, method 1: 235 °C, 2 s 19 0 −0.3 9.3 0 −0.2 19 (17.1 min.) 7.5 19 max. 2 0 −0.3 +0.2 0 0.8 0 −0.1 5.08 7.5 +0.2 9.3 0 0 −0.2 +0.1 0 3 0.8 ±0.02 29.1 max. CBW034 24.1 max. 1.3 +0.15 0 Dimensions in mm. Fig.3 E30/15/7 coil former; 10-pins. WINDING DATA AND AREA PRODUCT FOR 10-PINS E30/15/7 COIL FORMER (E) NUMBER OF NECTIONS WINDING AREA (mm2) MINIMUM WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm4) 1 80 17.1 56 4800 2008 Sep 01 391 TYPE NUMBER CSH-E30/15/7-1S-10P Ferroxcube E cores and accessories E30/15/7 MOUNTING PARTS General data and ordering information ITEM REMARKS FIGURE TYPE NUMBER Clasp CuZn alloy, Ni plated 4 CLA-E30/15/7 Spring stainless steel (CrNi) 5 SPR-E30/15/7 10.5 3.9 0.8 7.6 min. 8.8 ±0.1 2.5 2.9 7.5 0 −0.1 2 ; ;; ;; ;; ;;;;; 0.65 0.9 28 CBW036 0.4 (2×) 3.3 0 −0.15 CBW035 0.5 24 31.1 max. Dimensions in mm. Dimensions in mm. Fig.4 E30/15/7 clasp. 2008 Sep 01 2.2 32.2 ±0.2 5 32 12.8 0.6 Fig.5 E30/15/7 spring. 392 Ferroxcube E cores and accessories E30/15/7 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 393