Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32651 ... B32656 Date: December 2012 © EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Metallized polypropylene film capacitors (MKP) B32651 ... B32656 High pulse (wound) Typical applications Electronic ballasts Switch-mode power supplies Dimensional drawing Climatic Max. operating temperature: 110 °C Climatic category (IEC 60068-1): 55/100/56 Construction Dielectric: polypropylene (PP) Wound capacitor technology with internal series connection for VR ≥1250 V DC Plastic case (UL 94 V-0) Epoxy resin sealing Dimensions in mm Features High pulse strength High contact reliability RoHS-compatible Halogen-free capacitors available on request Terminals Parallel wire leads, lead-free tinned Special lead lengths available on request Lead spacing ±0.4 10 15 22.5 27.5 37.5 Marking Manufacturer's logo, lot number ( ≤27.5 mm), series number (e.g. 651), rated capacitance (coded), cap. tolerance (code letter), rated DC voltage (AC voltage for 1600 V DC/700 V AC and 2000 V DC/1000 V AC), date of manufacture (coded) Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to chapter "Taping and packing“. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 39 Lead diameter d1 0.6 0.8 0.8 0.8 1.0 Type B32651 B32652 B32653 B32654 B32656 B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 10 mm Type B32651 Page 8 VR (V DC) 1250 VRMS (V AC) 450 CR (nF) 2.2 3.3 4.7 6.8 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 39 B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 15 mm Type B32652 Page 9 VR (V DC) 250 400 630 1000 1250 1600 1600 2000 VRMS (V AC) 160 200 250 250 500 500 700 700 CR (nF) 1.0 1.5 2.2 3.3 4.7 5.6 6.8 10 12 15 22 33 47 56 68 100 120 150 220 330 390 470 560 680 820 1000 Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 39 B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 22.5 mm Type B32653 Page 12 VR (V DC) 250 400 630 1000 1250 1600 2000 2000 VRMS (V AC) 160 200 250 250 500 500 700 1000 CR (nF) 2.2 3.3 4.7 6.8 10 12 15 22 33 47 56 68 82 100 120 150 220 330 470 560 680 1000 1200 1500 2200 3300 Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 39 B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 27.5 mm Type B32654 Page 15 VR (V DC) 250 400 630 1000 1250 1600 2000 VRMS (V AC) 160 200 250 250 500 500 700 CR (nF) 22 33 47 68 82 100 150 220 330 470 560 680 820 1000 1200 1500 2200 2700 3300 4700 5600 6800 8200 Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 39 B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 37.5 mm Type B32656 Page 17 VR (V DC) 850 1000 1250 1600 2000 VRMS (V AC) 450 500 500 600 700 CR (nF) 100 120 150 220 270 330 390 470 560 680 820 1000 1200 1500 2200 Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 39 B32651 High pulse (wound) Ordering codes and packing units (lead spacing 10 mm) VR V DC1) 1250 VRMS CR f ≤1 kHz V AC nF 450 2.2 3.3 4.7 6.8 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 Ordering code (composition see below) B32651A7222+*** B32651A7332+*** B32651A7472+*** B32651A7682+*** Ammo pack pcs./MOQ 4000 3320 3320 2720 Reel Untaped pcs./MOQ 6800 5200 5200 4400 pcs./MOQ 4000 4000 4000 4000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) 1) For pulse loads (pulse width ≤ 1000 µs), a peak voltage of 1400 Vp can be permitted. Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 39 B32652 High pulse (wound) Ordering codes and packing units (lead spacing 15 mm) VR V DC 250 400 630 VRMS CR f ≤1 kHz V AC nF 160 150 220 330 470 680 820 1000 200 68 100 150 220 330 470 560 680 250 33 47 68 100 150 220 330 390 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32652A3154+*** B32652A3224+*** B32652A3334+*** B32652A3474+*** B32652A3684+*** B32652A3824+*** B32652A3105+*** B32652A4683+*** B32652A4104+*** B32652A4154+*** B32652A4224+*** B32652A4334+*** B32652A4474+*** B32652A4564+*** B32652A4684+*** B32652A6333+*** B32652A6473+*** B32652A6683+*** B32652A6104+*** B32652A6154+*** B32652A6224+*** B32652A6334+*** B32652A6394+*** Ammo pack pcs./MOQ 4680 3840 3320 2720 2560 4680 4680 3840 3320 2720 2560 4680 4680 3840 3320 2720 2560 Reel pcs./ MOQ 5200 4400 3600 2800 2800 2200 2200 5200 5200 4400 3600 2800 2800 2200 2200 5200 2800 4400 3600 2800 2800 2200 2200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 9 of 39 Untaped pcs./ MOQ 4000 4000 1000 2000 2000 1000 1000 4000 4000 4000 4000 2000 2000 1000 1000 4000 4000 4000 4000 2000 2000 1000 1000 B32652 High pulse (wound) Ordering codes and packing units (lead spacing 15 mm) VR V DC 1000 1250 1600 1600 VRMS CR f ≤1 kHz V AC nF 250 10 15 22 33 47 68 100 120 150 500 6.8 10 15 22 33 47 56 500 3.3 4.7 6.8 10 15 22 700 2.2 3.3 4.7 6.8 10 12 15 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32652A0103+*** B32652A0153+*** B32652A0223+*** B32652A0333+*** B32652A0473+*** B32652A0683+*** B32652A0104+*** B32652A0124+*** B32652A0154+*** B32652A7682+*** B32652A7103+*** B32652A7153+*** B32652A7223+*** B32652A7333+*** B32652A7473+*** B32652A7563+*** B32652A1332+*** B32652A1472+*** B32652A1682+*** B32652A1103+*** B32652A1153+*** B32652A1223+*** B32652J1222+*** B32652J1332+*** B32652J1472+*** B32652J1682+*** B32652J1103+*** B32652J1123+*** B32652J1153+*** Ammo pack pcs./MOQ 4680 4680 4680 3840 3320 2720 2560 4680 3840 3320 2720 2560 4680 3840 3320 2720 2560 4680 3840 3320 2720 2560 2560 Reel pcs./ MOQ 5200 5200 5200 4400 3600 2800 2800 2200 2200 5200 4400 3600 2800 2800 2200 2200 5200 4400 3600 2800 2800 2200 5200 4400 3600 2800 2800 2800 2200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 10 of 39 Untaped pcs./ MOQ 4000 4000 4000 4000 4000 2000 2000 1000 1000 4000 4000 4000 2000 2000 1000 1000 4000 4000 4000 2000 2000 1000 4000 4000 4000 2000 2000 2000 1000 B32652 High pulse (wound) Ordering codes and packing units (lead spacing 15 mm) VR V DC 2000 VRMS CR f ≤1 kHz V AC nF 700 1.0 1.5 2.2 3.3 4.7 5.6 6.8 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32652A2102+*** B32652A2152+*** B32652A2222+*** B32652A2332+*** B32652A2472+*** B32652A2562+*** B32652A2682+*** Ammo pack pcs./MOQ 4680 3840 3320 2720 2560 Reel pcs./ MOQ 5200 4400 3600 2800 2800 2200 2200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 11 of 39 Untaped pcs./ MOQ 4000 4000 4000 2000 2000 1000 1000 B32653 High pulse (wound) Ordering codes and packing units (lead spacing 22.5 mm) VR V DC 250 400 630 VRMS CR f ≤1 kHz V AC nF 160 220 330 470 680 1000 1200 1500 2200 3300 200 150 220 330 470 680 1000 1200 1500 2200 250 100 150 220 330 470 560 680 1000 1200 Max. dimensions w×h×l mm 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 12.0 × 22.0 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 Ordering code (composition see below) B32653A3224+*** B32653A3334+*** B32653A3474+*** B32653A3684+*** B32653A3105+*** B32653A3125+*** B32653A3155+*** B32653A3225+000 B32653A3335+000 B32653A4154+*** B32653A4224+*** B32653A4334+*** B32653A4474+*** B32653A4684+*** B32653A4105+*** B32653A4125+000 B32653A4155+000 B32653A4225+000 B32653A6104+*** B32653A6154+*** B32653A6224+*** B32653A6334+*** B32653A6474+*** B32653A6564+*** B32653A6684+000 B32653A6105+000 B32653A6125+000 Ammo pack pcs./MOQ 2720 2720 2320 1920 1560 1560 1480 2720 2720 2320 1920 1560 1480 2720 2720 1920 1560 1480 1480 Reel pcs./ MOQ 2800 2800 2400 2000 1600 1600 1400 2800 2800 2400 2000 1600 1400 2800 2800 2000 1600 1400 1400 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 12 of 39 Untaped pcs./ MOQ 2880 2880 2520 2040 2160 2160 2040 1040 1040 2880 2880 2520 2040 2160 2040 1800 1040 1040 2880 2880 2040 2160 2040 2040 1040 1040 1040 B32653 High pulse (wound) Ordering codes and packing units (lead spacing 22.5 mm) VR V DC 1000 1250 1600 VRMS CR f ≤1 kHz V AC nF 250 33 47 68 100 150 220 330 470 560 500 22 33 47 68 100 120 150 220 500 6.8 10 15 22 33 47 56 68 82 100 Max. dimensions w×h×l mm 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 12.0 × 22.0 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 12.0 × 22.0 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 Ordering code (composition see below) B32653A0333+*** B32653A0473+*** B32653A0683+*** B32653A0104+*** B32653A0154+*** B32653A0224+*** B32653A0334+000 B32653A0474+000 B32653A0564+000 B32653A7223+*** B32653A7333+*** B32653A7473+*** B32653A7683+*** B32653A7104+*** B32653A7124+000 B32653A7154+000 B32653A7224+000 B32653A1682+*** B32653A1103+*** B32653A1153+*** B32653A1223+*** B32653A1333+*** B32653A1473+*** B32653A1563+000 B32653A1683+000 B32653A1823+000 B32653A1104+000 Ammo pack pcs./MOQ 2720 2720 2720 1920 1560 1480 2720 2720 1920 1560 1480 2720 2720 2320 1920 1560 1480 Reel pcs./ MOQ 2800 2800 2800 2000 1600 1400 2800 2800 2000 1600 1400 2800 2800 2400 2000 1600 1400 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 13 of 39 Untaped pcs./ MOQ 2880 2880 2880 2040 2160 2040 2160 2160 2160 2880 2880 2040 2160 2040 1800 1040 1040 2880 2880 2520 2040 2160 2040 1800 1040 1040 1040 B32653 High pulse (wound) Ordering codes and packing units (lead spacing 22.5 mm) VR V DC 2000 2000 VRMS CR f ≤1 kHz V AC nF 700 3.3 4.7 6.8 10 15 22 33 1000 2.2 3.3 4.7 6.8 10 12 15 22 Max. dimensions w×h×l mm 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 10.5 × 20.5 × 26.5 12.0 × 22.0 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 Ordering code (composition see below) B32653A2332+*** B32653A2472+*** B32653A2682+*** B32653A2103+*** B32653A2153+*** B32653A2223+000 B32653A2333+000 B32653A8222+*** B32653A8332+*** B32653A8472+*** B32653A8682+*** B32653A8103+*** B32653A8123+000 B32653A8153+000 B32653A8223+000 Ammo pack pcs./MOQ 2720 2720 1920 1560 1480 2720 2720 1920 1560 1560 Reel pcs./ MOQ 2800 2800 2000 1600 1400 2800 2800 2000 1600 1600 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 14 of 39 Untaped pcs./ MOQ 2880 2880 2040 2160 2040 2160 2160 2880 2880 2040 2160 2160 1800 2160 2160 B32654 High pulse (wound) Ordering codes and packing units (lead spacing 27.5 mm) VR V DC 250 400 630 1000 VRMS CR f ≤1 kHz V AC nF 160 1500 2200 3300 4700 5600 6800 8200 200 1000 1500 2200 3300 4700 5600 250 680 1000 1500 2200 2700 3300 250 220 330 470 680 820 1000 1200 1500 Max. dimensions w×h×l mm 11.0 × 21.0 × 31.5 12.5 × 21.5 × 31.5 15.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 19.0 × 30.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 11.0 × 21.0 × 31.5 12.5 × 21.5 × 31.5 14.0 × 24.5 × 31.5 19.0 × 30.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 11.0 × 21.0 × 31.5 13.5 × 23.0 × 31.5 18.0 × 27.5 × 31.5 18.0 × 33.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 11.0 × 21.0 × 31.5 11.0 × 21.0 × 31.5 14.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 19.0 × 30.0 × 31.5 21.0 × 31.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 Ordering code (composition see below) B32654A3155+*** B32654A3225+*** B32654A3335+000 B32654A3475+000 B32654A3565+000 B32654A3685+000 B32654A3825+000 B32654A4105+*** B32654A4155+*** B32654A4225+*** B32654A4335+000 B32654A4475+000 B32654A4565+000 B32654A6684+*** B32654A6105+*** B32654A6155+000 B32654A6225+000 B32654A6275+000 B32654A6335K000 B32654A0224+*** B32654A0334+*** B32654A0474+*** B32654A0684+000 B32654A0824+000 B32654A0105+000 B32654A0125+000 B32654A0155K000 Ammo pack pcs./MOQ Reel pcs./ MOQ 1400 1200 1400 1200 1040 1400 1000 1400 1400 1040 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 15 of 39 Untaped pcs./ MOQ 1280 1120 960 800 720 640 640 1280 1120 1040 720 640 640 1280 1040 800 800 640 640 1280 1280 1040 800 720 720 640 640 B32654 High pulse (wound) Ordering codes and packing units (lead spacing 27.5 mm) VR V DC 1250 1600 2000 VRMS CR f ≤1 kHz V AC nF 500 100 150 220 330 470 560 680 500 47 68 100 150 220 700 22 33 47 68 82 100 Max. dimensions w×h×l mm 11.0 × 21.0 × 31.5 11.0 × 21.0 × 31.5 14.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 21.0 × 31.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 11.0 × 21.0 × 31.5 11.0 × 21.0 × 31.5 14.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 21.0 × 31.0 × 31.5 11.0 × 21.0 × 31.5 13.5 × 23.0 × 31.5 18.0 × 27.5 × 31.5 19.0 × 30.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 Ordering code (composition see below) B32654A7104+*** B32654A7154+*** B32654A7224+*** B32654A7334+000 B32654A7474+000 B32654A7564+000 B32654A7684+000 B32654A1473+*** B32654A1683+*** B32654A1104+*** B32654A1154+000 B32654A1224+000 B32654A2223+*** B32654A2333+*** B32654A2473+000 B32654A2683+000 B32654A2823+000 B32654A2104+000 Ammo pack pcs./MOQ Reel pcs./ MOQ 1400 1400 1040 1400 1400 1040 1400 1000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 189 = Reel 000 = Untaped (lead length 6 1 mm) Page 16 of 39 Untaped pcs./ MOQ 1280 1280 1040 800 720 640 640 1280 1280 1040 800 784 1280 1040 800 720 640 640 B32656 High pulse (wound) Ordering codes and packing units (lead spacing 37.5 mm) VR V DC 850 1000 1250 VRMS CR f ≤1 kHz V AC nF 450 220 330 470 680 680 820 1000 500 470 470 680 680 1000 1200 1500 2200 500 220 270 330 390 470 680 820 1000 1200 Max. dimensions w×h×l mm 12.0 × 22.0 × 42.0 12.0 × 22.0 × 42.0 12.0 × 22.0 × 42.0 16.0 × 28.5 × 42.0 24.0 × 15.0 × 41.5 24.0 × 19.0 × 41.5 18.0 × 32.5 × 42.0 14.0 × 25.0 × 42.0 24.0 × 15.0 × 41.5 16.0 × 28.5 × 42.0 24.0 × 19.0 × 41.5 20.0 × 39.5 × 42.0 28.0 × 37.0 × 42.0 28.0 × 37.0 × 42.0 30.0 × 45.0 × 42.0 14.0 × 25.0 × 42.0 24.0 × 15.0 × 41.5 16.0 × 28.5 × 42.0 24.0 × 19.0 × 41.5 18.0 × 32.5 × 42.0 20.0 × 39.5 × 42.0 28.0 × 37.0 × 42.0 28.0 × 37.0 × 42.0 28.0 × 42.5 × 41.5 Ordering code (composition see below) B32656A8224+000 B32656A8334+000 B32656A8474+000 B32656A8684+000 B32656T8684+000 B32656T8824+000 B32656A8105+000 B32656A0474+000 B32656T0474+000 B32656A0684+000 B32656T0684+000 B32656A0105+000 B32656A0125+000 B32656A0155+000 B32656A0225+000 B32656A7224+000 B32656T7274+000 B32656A7334+000 B32656T7394+000 B32656A7474+000 B32656A7684+000 B32656A7824+000 B32656A7105+000 B32656A7125+000 Untaped pcs./MOQ 1620 1620 1620 800 1040 780 720 1380 1040 800 780 640 440 440 400 1380 1040 800 780 720 640 440 440 440 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 000 = Untaped (lead length 6 1 mm) Page 17 of 39 B32656 High pulse (wound) VR V DC 1600 2000 VRMS CR f ≤1 kHz V AC nF 600 100 150 150 220 220 330 470 560 680 820 700 100 100 120 150 220 330 470 Max. dimensions w×h×l mm 12.0 × 22.0 × 42.0 14.0 × 25.0 × 42.0 24.0 × 15.0 × 41.5 16.0 × 28.5 × 42.0 24.0 × 19.0 × 41.5 20.0 × 39.5 × 41.5 28.0 × 37.0 × 42.0 28.0 × 37.0 × 42.0 28.0 × 42.5 × 41.5 30.0 × 45.0 × 42.0 14.0 × 25.0 × 42.0 24.0 × 15.0 × 41.5 24.0 × 19.0 × 41.5 18.0 × 32.5 × 42.0 20.0 × 39.5 × 42.0 28.0 × 37.0 × 42.0 30.0 × 45.0 × 42.0 Ordering code (composition see below) B32656J1104+000 B32656J1154+000 B32656T1154+000 B32656J1224+000 B32656T1224+000 B32656J1334+000 B32656J1474+000 B32656J1564+000 B32656J1684+000 B32656J1824+000 B32656J2104+000 B32656T2104+000 B32656T2124+000 B32656J2154+000 B32656J2224+000 B32656J2334+000 B32656J2474+000 Untaped pcs./MOQ 1620 1380 1040 800 780 640 440 440 440 400 1380 1040 780 720 640 440 400 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 000 = Untaped (lead length 6 1 mm) Page 18 of 39 B32651 ... B32656 High pulse (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR Dissipation factor tan δ (in 10-3) at at 20 °C (upper limit values) ≤27 nF 27 nF<CR≤0.1 µF 1 kHz 0.8 10 kHz 1.0 100 kHz 2.0 0.8 1.0 3.0 CR ≤ 0.33 µF CR > 0.33 µF Insulation resistance Rins or time constant τ = CR Rins 100 GΩ 30000 s at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage 1.6 VR, 2 s TA (°C) DC voltage derating Category voltage VC (continuous operation with VDC TA ≤ 85 VC = VR or VAC at f ≤ 1 kHz) 85<TA≤100 VC = VR (165TA)/80 TA (°C) DC voltage (max. hours) Operating voltage Vop for short operating periods TA ≤ 85 Vop = 1.25 VC (2000 h) (VDC or VAC at f ≤ 1 kHz) 85<TA≤100 Vop = 1.25 VC (2000 h) Damp heat test 56 days/40 °C/93% relative humidity Limit values after damp Capacitance change ∆C/C heat test Dissipation factor change ∆ tan δ Insulation resistance Rins or time constant τ = CR Rins Reliability: Failure rate λ Service life tSL Failure criteria: Total failure Failure due to variation of parameters Please read Cautions and warnings and Important notes at the end of this document. +110 °C +100 °C 55 °C +85 °C 0.1 µF<CR≤1 µF >1 µF 0.8 1.0 0.8 AC voltage derating VC,RMS = VRMS VC,RMS=VRMS (165TA)/80 AC voltage (max. hours) Vop = 1.0 VC,RMS (2000 h) Vop = 1.0 VC,RMS (2000 h) ≤ 3% ≤ 0.5 10-3 (at 1 kHz) ≤ 1.0 10-3 (at 10 kHz) ≥ 50% of minimum as-delivered values 1 fit (≤ 1 10-9/h) at 0.5 VR, 40 °C 200 000 h at 1.0 VR, 85 °C For conversion to other operating conditions and temperatures, refer to chapter "Quality, 2 Reliability". Short circuit or open circuit Capacitance change ∆C/C Dissipation factor tan δ Insulation resistance Rins or time constant τ = CR Rins Page 19 of 39 > 10% > 4 upper limit value < 1500 MΩ (CR≤0.33 µF) < 500 s (CR>0.33 µF) B32651 ... B32656 High pulse (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt values Lead spacing VR VRMS V DC V AC 250 160 400 200 630 250 850 450 1000 250 500 1250 450 500 1600 500 600 700 2000 700 1000 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm dV/dt in V/µs 4000 200 300 400 975 1850 4500 5200 8000 120 180 300 600 1150 2400 7000 7500 50 100 150 300 600 1000 2300 90 100 140 210 200 Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 39 B32651 ... B32656 High pulse (wound) k0 values Lead spacing VR VRMS V DC V AC 250 160 400 200 630 250 850 450 1000 250 500 1250 450 500 1600 500 600 700 2000 700 1000 10 mm k0 in V2/µs 25 000 000 15 mm 22.5 mm 100 000 250 000 500 000 60 000 200 000 350 000 25 000 110 000 250 000 3 000 000 9 000 000 20 000 000 28 000 000 60 000 000 1 500 000 3 750 000 10 000 000 1 000 000 2 000 000 4 000 000 15 000 000 40 000 000 50 000 000 Impedance Z versus frequency f (typical values) Please read Cautions and warnings and Important notes at the end of this document. 27.5 mm Page 21 of 39 37.5 mm 153 000 180 000 350 000 672 000 800 000 B32651 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 10 mm 1250 V DC/450 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 39 B32652 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 15 mm 250 V DC/160 V AC 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 39 B32652 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 15 mm 1250 V DC/500 V AC 1600 V DC/500 V AC 1600 V DC/700 V AC 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 39 B32653 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 22.5 mm 250 V DC/160 V AC 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 25 of 39 B32653 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 22.5 mm 1250 V DC/500 V AC 1600 V DC/500 V AC 2000 V DC/700 V AC 2000 V DC/1000 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 26 of 39 B32654 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 27.5 mm 250 V DC/160 V AC 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 27 of 39 B32654 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 27.5 mm 1250 V DC/500 V AC 1600 V DC/500 V AC 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 28 of 39 B32656 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 37.5 mm 850 V DC/450 V AC 1000 V DC/500 V AC 1250 V DC/500 V AC 1600 V DC/600 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 29 of 39 B32656 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 37.5 mm 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 30 of 39 B32651 ... B32656 High pulse (wound) Mounting guidelines 1 Soldering 1.1 Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature 235 ±5 °C Soldering time 2.0 ±0.5 s Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane Evaluation criteria: Visual inspection Wetting of wire surface by new solder ≥90%, free-flowing solder 1.2 Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) Please read Cautions and warnings and Important notes at the end of this document. Page 31 of 39 10 ±1 s 5 ±1 s <4s recommended soldering profile for MKT uncoated (lead spacing ≤ 10 mm) and insulated (B32559) B32651 ... B32656 High pulse (wound) Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane Shield Heat-absorbing board, (1.5 ±0.5) mm thick, between capacitor body and liquid solder Evaluation criteria: Visual inspection ∆C/C0 tan δ Please read Cautions and warnings and Important notes at the end of this document. No visible damage 2% for MKT/MKP/MFP 5% for EMI suppression capacitors As specified in sectional specification Page 32 of 39 B32651 ... B32656 High pulse (wound) 1.3 General notes on soldering Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics. For short exposures (as in practical soldering processes) the heat load (and thus the possible effects on a capacitor) will also depend on other factors like: Pre-heating temperature and time Forced cooling immediately after soldering Terminal characteristics: diameter, length, thermal resistance, special configurations (e.g. crimping) Height of capacitor above solder bath Shadowing by neighboring components Additional heating due to heat dissipation by neighboring components Use of solder-resist coatings The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced cooling process may possibly have to be included. EPCOS recommends the following conditions: Pre-heating with a maximum temperature of 110 °C Temperature inside the capacitor should not exceed the following limits: MKP/MFP 110 °C MKT 160 °C When SMD components are used together with leaded ones, the leaded film capacitors should not pass into the SMD adhesive curing oven. The leaded components should be assembled after the SMD curing step. Leaded film capacitors are not suitable for reflow soldering. Uncoated capacitors For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following measures are recommended: pre-heating to not more than 110 °C in the preheater phase rapid cooling after soldering Please read Cautions and warnings and Important notes at the end of this document. Page 33 of 39 B32651 ... B32656 High pulse (wound) Cautions and warnings Do not exceed the upper category temperature (UCT). Do not apply any mechanical stress to the capacitor terminals. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after it has been soldered to the PC board. Do not pick up the PC board by the soldered capacitor. Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified lead spacing. Do not exceed the specified time or temperature limits during soldering. Avoid external energy inputs, such as fire or electricity. Avoid overload of the capacitors. The table below summarizes the safety instructions that must always be observed. A detailed description can be found in the relevant sections of the chapters "General technical information" and "Mounting guidelines". Topic Storage conditions Flammability Resistance to vibration Safety information Reference chapter "General technical information" Make sure that capacitors are stored within the 4.5 specified range of time, temperature and humidity "Storage conditions" conditions. Avoid external energy, such as fire or electricity 5.3 (passive flammability), avoid overload of the "Flammability" capacitors (active flammability) and consider the flammability of materials. Do not exceed the tested ability to withstand 5.2 vibration. The capacitors are tested to "Resistance to vibration" IEC 60068-2-6. EPCOS offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. Consult our catalog "Film Capacitors for Automotive Electronics". Please read Cautions and warnings and Important notes at the end of this document. Page 34 of 39 B32651 ... B32656 High pulse (wound) Topic Safety information Soldering Do not exceed the specified time or temperature limits during soldering. Cleaning Use only suitable solvents for cleaning capacitors. Embedding of When embedding finished circuit assemblies in capacitors in plastic resins, chemical and thermal influences finished assemblies must be taken into account. Caution: Consult us first, if you also wish to embed other uncoated component types! Please read Cautions and warnings and Important notes at the end of this document. Page 35 of 39 Reference chapter "Mounting guidelines" 1 "Soldering" 2 "Cleaning" 3 "Embedding of capacitors in finished assemblies" B32651 ... B32656 High pulse (wound) Symbols and terms Symbol α αC A βC C CR ∆C ∆C/C ∆C/CR dt ∆t ∆T ∆tan δ ∆V dV/dt ∆V/∆t E ESL ESR f f1 f2 fr FD FT i IC English Heat transfer coefficient Temperature coefficient of capacitance Capacitor surface area Humidity coefficient of capacitance Capacitance Rated capacitance Absolute capacitance change Relative capacitance change (relative deviation of actual value) Capacitance tolerance (relative deviation from rated capacitance) Time differential Time interval Absolute temperature change (self-heating) Absolute change of dissipation factor Absolute voltage change Time differential of voltage function (rate of voltage rise) Voltage change per time interval Activation energy for diffusion Self-inductance Equivalent series resistance Frequency Frequency limit for reducing permissible AC voltage due to thermal limits German Wärmeübergangszahl Temperaturkoeffizient der Kapazität Kondensatoroberfläche Feuchtekoeffizient der Kapazität Kapazität Nennkapazität Absolute Kapazitätsänderung Relative Kapazitätsänderung (relative Abweichung vom Ist-Wert) Kapazitätstoleranz (relative Abweichung vom Nennwert) Differentielle Zeit Zeitintervall Absolute Temperaturänderung (Selbsterwärmung) Absolute Änderung des Verlustfaktors Absolute Spannungsänderung Differentielle Spannungsänderung (Spannungsflankensteilheit) Spannungsänderung pro Zeitintervall Aktivierungsenergie zur Diffusion Eigeninduktivität Ersatz-Serienwiderstand Frequenz Grenzfrequenz für thermisch bedingte Reduzierung der zulässigen Wechselspannung Frequency limit for reducing permissible Grenzfrequenz für strombedingte AC voltage due to current limit Reduzierung der zulässigen Wechselspannung Resonant frequency Resonanzfrequenz Thermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur Diffusion Derating factor Deratingfaktor Current (peak) Stromspitze Category current (max. continuous Kategoriestrom (max. Dauerstrom) current) Please read Cautions and warnings and Important notes at the end of this document. Page 36 of 39 B32651 ... B32656 High pulse (wound) Symbol IRMS iz k0 LS λ λ0 λtest Pdiss Pgen Q ρ R R Ri Rins RP RS S t T τ tan δ tan δD tan δP tan δS TA Tmax Tmin tOL Top TR Tref tSL VAC English (Sinusoidal) alternating current, root-mean-square value Capacitance drift Pulse characteristic Series inductance Failure rate Constant failure rate during useful service life Failure rate, determined by tests Dissipated power Generated power Heat energy Density of water vapor in air Universal molar constant for gases Ohmic resistance of discharge circuit Internal resistance Insulation resistance Parallel resistance Series resistance severity (humidity test) Time Temperature Time constant Dissipation factor Dielectric component of dissipation factor Parallel component of dissipation factor Series component of dissipation factor Ambient temperature Upper category temperature Lower category temperature Operating life at operating temperature and voltage Operating temperature Rated temperature Reference temperature Reference service life AC voltage Please read Cautions and warnings and Important notes at the end of this document. German (Sinusförmiger) Wechselstrom Inkonstanz der Kapazität Impulskennwert Serieninduktivität Ausfallrate Konstante Ausfallrate in der Nutzungsphase Experimentell ermittelte Ausfallrate Abgegebene Verlustleistung Erzeugte Verlustleistung Wärmeenergie Dichte von Wasserdampf in Luft Allg. Molarkonstante für Gas Ohmscher Widerstand des Entladekreises Innenwiderstand Isolationswiderstand Parallelwiderstand Serienwiderstand Schärfegrad (Feuchtetest) Zeit Temperatur Zeitkonstante Verlustfaktor Dielektrischer Anteil des Verlustfaktors Parallelanteil des Verlfustfaktors Serienanteil des Verlustfaktors Umgebungstemperatur Obere Kategorietemperatur Untere Kategorietemperatur Betriebszeit bei Betriebstemperatur und -spannung Beriebstemperatur Nenntemperatur Referenztemperatur Referenz-Lebensdauer Wechselspannung Page 37 of 39 B32651 ... B32656 High pulse (wound) Symbol VC VC,RMS English Category voltage Category AC voltage VCD Vch VDC VFB Vi Vo Vop Vp Vpp VR Corona-discharge onset voltage Charging voltage DC voltage Fly-back capacitor voltage Input voltage Output voltage Operating voltage Peak pulse voltage Peak-to-peak voltage Impedance Rated voltage Amplitude of rated AC voltage R VRMS German Kategoriespannung (Sinusförmige) Kategorie-Wechselspannung Teilentlade-Einsatzspannung Ladespannung Gleichspannung Spannung (Flyback) Eingangsspannung Ausgangssspannung Betriebsspannung Impuls-Spitzenspannung Spannungshub Nennspannung Amplitude der Nenn-Wechselspannung VSC Vsn (Sinusoidal) alternating voltage, root-mean-square value S-correction voltage Snubber capacitor voltage Z Impedance Spannung bei Anwendung "S-correction" Spannung bei Anwendung "Beschaltung" Scheinwiderstand Lead spacing Rastermaß Please read Cautions and warnings and Important notes at the end of this document. (Sinusförmige) Wechselspannung Page 38 of 39 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 39 of 39