MUR520 THRU MUR560 R GLASS PASSIVATED SUPER FAST RECTIFIER Reverse Voltage - 200 -600 Volts Forward Current - 5.0Amperes S E M I C O N D U C T O R FEATURES TO-220AC Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Fast switching for high efficiency Low forward voltage drop Single rectifier construction High surge capability For use in low voltage ,high frequency inverters, free wheeling ,and polarity protection applications JF MUR560 High temperature soldering guaranteed:260°C/10 seconds, 0.25"(6.35mm)from case Component in accordance to RoHS 2011/65/EU 0.159(4.05) 0.185(4.70) 0.410(10.42) 0.161(4.10) 0.388(9.85) 0.147(3.74) DIA 0.175(4.44) 0.055(1.39) 0.045(1.14) 0.113(2.88) 0.102(2.60) 0.283(7.20) 0.244(6.20) 0.610(15.50) 0.571(14.50) 1 PIN 2 1.161(29.50) 0.114(2.90) 1.106(28.10) 0.140(3.55) 0.560(14.22) 0.053(1.34) 0.098(2.50) 0.512(13.00) 0.047(1.20) 0.037(0.94) MECHANICAL DATA 0.027(0.68) 0.023(0.58) Case: JEDEC TO-220AC molded plastic body 0.014(0.35) 0.208(5.28) Terminals: Lead solderable per MIL-STD-750,method 2026 0.192(4.88) Polarity: As marked Mounting Position: Any Dimensions in inches and (millimeters) Weight: 0.08ounce, 2.24 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Ratings at 25°C ambient temperature unless otherwise specified ,Single phase ,half wave ,resistive or inductive load. For capacitive load,derate by 20%.) Symbols MUR520 MUR540 MUR560 Units 200 400 600 140 280 420 Maximum DC blocking voltage VRRM VRMS VDC 200 400 600 Volts Volts Volts Maximum average forward rectified current(see Fig.1) I(AV) 5.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150.0 75 Amps Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum instantaneous forward voltage at 10.0 A(Note 1 ) Maximum instantaneous reverse current at rated DC blocking voltage(Note 1) VF T A =25°C R Operating junction temperature range TJ TSTG 1.7 Volts uA 500 Trr Typical thermal resistance (Note 3) 1.3 5 IR TA =125°C Maximum Reverse Recovery Time (Note 2) Storage temperature range 0.975 JC 35 ns 2.5 °C/W -40 to+150 °C -40 to+150 °C Notes: 1. Pulse test: 300μs pulse width,1% duty cycle 2. Reverse recovery test conditions IF=0.5A,IR=1.0A, Irr=0.25A 3. Thermal resistance from junction to case JINAN JINGHENG ELECTRONICS CO., LTD. 9-10 HTTP://WWW.JINGHENGGROUP.COM RATINGS AND CHARACTERISTIC CURVES MUR520 THRU MUR560 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES FIG.1-FORWARD CURRENT DERATING CURVE 6 5 RESISTIVE OR INDUCTVE LOAD 4 3 2 1 0 0 20 40 60 80 100 120 180 150 LEAD TEMPERATURE (°C) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 105 8.3ms Single Half Sine-Wave (JEDEC Method) 90 75 60 45 30 15 0 1 2 20 50 100 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 50 10 200V 400V 10 INSTANTANEOUS REVERSE CURRENT (UA) INSTANTANEOUS FORWARD CURRENT( AMPERES) 10 5 NUMBER OF CYCLES AT 60Hz 600V PULSE WIDTH=300μS 1% DUTY CYCLE 1 0.1 TJ=100°C 1 TJ=25°C 0.1 0.01 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.001 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE% FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/ W FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 400 TJ=25°C f=1.0MHZ Vsig=50mVp-p 100 10 0.1 1 10 100 REVERSE VOLTAGE. VOLTS JINAN JINGHENG ELECTRONICS CO., LTD. 100 10 1 0.1 0.01 0.1 1 10 100 T, PULSE DURATION ,sec. 9-11 HTTP://WWW.JINGHENGGROUP.COM