Taiyo Yuden FBMH1608HM151-T Chip bead inductors for power lines (fb series m type) Datasheet

Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products.
Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification.
■ Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification
is available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDEN s official sales channel ).
It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel.
■ Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may
occur in connection with a third party's intellectual property rights and other related rights arising from your usage
of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Law of Japan, U.S. Export Administration Regulations , and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
14
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE)
CHIP BEAD INDUCTORS FOR POWER LINES （FB SERIES M TYPE）
■PARTS NUMBER
F
B
△
①
WAVE
REFLOW
*Operating Temp. : -40～+125℃（Including self-generated heat）
M J
② ③
3
2
1
6
H
④
①Series name
Code
FB
S
⑤
8
0 0
⑥
Shape
Rectangular chip
④Dimensions（L×W）
Type（inch）
1608
2125
2012
2016
3216
3225
4516
4525
4532
1608（0603）
2125（0805）
2012（0805）
2016（0806）
3216（1206）
3225（1210）
4516（1806）
4525（1810）
4532（1812）
Refer to impedance curves
for material differences
⑥Nominal impedance
Code
（example）
330
111
132
Characteristics
Standard
High Impedance type
Code
Material
⑦Impedance tolerance
Code
－
N
Dimensions
（L×W）［mm］
1.6×0.8
2.0×1.25
Nominal impedance［Ω］
33
110
1300
Impedance tolerance
±25％
±30％
⑧Packaging
Code
T
2.0×1.6
3.2×1.6
3.2×2.5
4.5×1.6
4.5×2.5
4.5×3.2
Packaging
Taping
⑨Internal code
Code
△
Internal code
Standard
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
Type
FB MJ1608
FB MJ2125
FB MJ3216
FB MJ4516
FB MH1608
FB MH2012
FB MH2016
FB MH3216
FB MH3225
FB MH4516
FB MH4525
FB MH4532
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be
checked beforehand.
A
1.0
1.4
1.4
1.75
1.0
1.4
1.4
1.4
1.4
1.75
1.75
1.75
B
1.0
1.2
2.2
3.5
1.0
1.2
1.2
2.2
2.2
3.5
3.5
3.5
C
1.0
1.65
2.0
2.0
1.0
1.65
2.0
2.0
2.9
2.0
2.9
3.7
Unit：mm
Standard quantity [pcs]
Paper tape
Embossed tape
Type
L
W
T
e
FB MJ1608
（0603）
FB MJ2125
（0805）
FB MJ3216
（1206）
FB MJ4516
（1806）
FB MH1608
（0603）
FB MH2012
（0805）
FB MH2016
（0806）
FB MH3216
（1206）
FB MH3225
（1210）
FB MH4516
（1806）
FB MH4525
（1810）
FB MH4532
（1812）
1.6±0.2
（0.063±0.008）
2.0±0.2
（0.079±0.008）
3.2±0.3
（0.126±0.012）
4.5±0.3
（0.177±0.012）
1.6±0.1
（0.063±0.004）
2.0±0.2
（0.079±0.008）
2.0±0.2
（0.079±0.008）
3.2±0.3
（0.126±0.012）
3.2±0.3
（0.126±0.012）
4.5±0.3
（0.177±0.012）
4.5±0.4
（0.177±0.016）
4.5±0.4
（0.177±0.016）
0.8±0.2
（0.031±0.008）
1.25±0.2
（0.049±0.008）
1.6±0.2
（0.063±0.008）
1.6±0.2
（0.063±0.008）
0.8±0.1
（0.031±0.004）
1.25±0.2
（0.049±0.008）
1.6±0.2
（0.063±0.008）
1.6±0.2
（0.063±0.008）
2.5±0.3
（0.098±0.012）
1.6±0.2
（0.063±0.008）
2.5±0.3
（0.098±0.012）
3.2±0.3
（0.126±0.012）
0.8±0.2
（0.031±0.008）
0.85±0.2
（0.033±0.008）
1.1±0.2
（0.043±0.008）
1.1±0.2
（0.043±0.008）
0.8±0.1
（0.031±0.004）
0.85±0.2
（0.033±0.008）
1.6±0.2
（0.063±0.008）
1.6±0.2
（0.063±0.008）
2.5±0.3
（0.098±0.012）
1.6±0.2
（0.063±0.008）
2.5±0.3
（0.098±0.012）
3.2±0.3
（0.126±0.012）
0.3±0.2
（0.012±0.008）
0.5±0.3
（0.020±0.012）
0.5±0.3
（0.020±0.012）
0.5±0.3
（0.020±0.012）
0.3±0.15
（0.012±0.006）
0.5±0.3
（0.020±0.012）
0.5±0.3
（0.020±0.012）
0.5±0.3
（0.020±0.012）
0.5±0.3
（0.020±0.012）
0.5±0.3
（0.020±0.012）
0.9±0.6
（0.035±0.024）
0.9±0.6
（0.035±0.024）
4000
－
4000
－
－
2000
－
2000
4000
－
4000
－
－
2000
－
2000
－
1000
－
2000
－
1000
－
2000
／ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
③Characteristics
Code
J
H
△＝Blank space
⑤Material
Code
HS
HM
HL
Series name
Ferrite bead
②Shape
Code
M
－ T △
⑦ ⑧ ⑨
Unit：mm（inch）
chipbeads_e-E02R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
14
109
■PARTS NUMBER
Standard type
●FB MJ1608
Parts number
FB MJ1608HS280NT
FB MJ1608HM230NT
EHS
RoHS
RoHS
Nominal impedance
（Ω）
28
23
Impedance tolerance
±30％
±30％
Measuring frequency
［MHz］
100
100
DC Resistance
［Ω］（max.）
0.007
0.007
Rated current
［A］（max.）
4.0
4.0
Thickness
［mm］
0.8 ±0.2
0.8 ±0.2
Measuring frequency
［MHz］
100
100
100
100
100
DC Resistance
［Ω］（max.）
0.004
0.008
0.004
0.008
0.008
Rated current
［A］（max.）
6.0
4.0
6.0
4.0
4.0
Thickness
［mm］
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
Measuring frequency
［MHz］
100
100
100
100
100
DC Resistance
［Ω］（max.）
0.005
0.010
0.005
0.010
0.012
Rated current
［A］（max.）
6.0
4.0
6.0
4.0
4.0
Thickness
［mm］
1.1 ±0.2
1.1 ±0.2
1.1 ±0.2
1.1 ±0.2
1.1 ±0.2
Measuring frequency
［MHz］
100
100
100
100
100
DC Resistance
［Ω］（max.）
0.007
0.014
0.007
0.014
0.014
Rated current
［A］（max.）
6.0
4.0
6.0
4.0
3.5
Thickness
［mm］
1.1 ±0.2
1.1 ±0.2
1.1 ±0.2
1.1 ±0.2
1.1 ±0.2
Measuring frequency
［MHz］
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
DC Resistance
［Ω］（max.）
0.020
0.025
0.035
0.050
0.070
0.130
0.150
0.170
0.350
0.028
0.045
0.130
0.170
0.210
0.350
0.450
Rated current
［A］（max.）
3.5
3.0
2.5
2.1
1.8
1.2
1.0
0.9
0.6
2.6
2.1
1.2
0.9
0.8
0.6
0.5
Thickness
［mm］
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
Measuring frequency
［MHz］
100
100
100
100
DC Resistance
［Ω］（max.）
0.025
0.032
0.060
0.080
Rated current
［A］（max.）
2.7
2.5
2.0
1.8
Thickness
［mm］
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
Measuring frequency
［MHz］
100
100
DC Resistance
［Ω］（max.）
0.015
0.050
Rated current
［A］（max.）
4.5
2.0
Thickness
［mm］
1.6 ±0.2
1.6 ±0.2
Measuring frequency
［MHz］
100
100
DC Resistance
［Ω］（max.）
0.020
0.070
Rated current
［A］（max.）
4.0
2.0
Thickness
［mm］
1.6 ±0.2
1.6 ±0.2
Measuring frequency
［MHz］
100
100
100
DC Resistance
［Ω］（max.）
0.042
0.100
0.130
Rated current
［A］（max.）
3.0
2.0
1.2
Thickness
［mm］
2.5 ±0.3
2.5 ±0.3
2.5 ±0.3
●FB MJ2125
FB
FB
FB
FB
FB
Parts number
EHS
MJ2125HS250NT
MJ2125HS420-T
MJ2125HM210NT
MJ2125HM330-T
MJ2125HL8R0NT
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
25
42
21
33
8
Impedance tolerance
±30％
±25％
±30％
±25％
±30％
●FB MJ3216
／ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
FB
FB
FB
FB
FB
Parts number
EHS
MJ3216HS480NT
MJ3216HS800-T
MJ3216HM380NT
MJ3216HM600-T
MJ3216HL160NT
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
48
80
38
60
16
Impedance tolerance
±30％
±25％
±30％
±25％
±30％
●FB MJ4516
FB
FB
FB
FB
FB
Parts number
EHS
MJ4516HS720NT
MJ4516HS111-T
MJ4516HM560NT
MJ4516HM900-T
MJ4516HL230NT
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
72
110
56
90
23
Impedance tolerance
±30％
±25％
±30％
±25％
±30％
High impedance type
●FB MH1608
Parts number
FB MH1608HM470-T
FB MH1608HM600-T
FB MH1608HM101-T
FB MH1608HM151-T
FB MH1608HM221-T
FB MH1608HM331-T
FB MH1608HM471-T
FB MH1608HM601-T
FB MH1608HM102-T
FB MH1608HL300-T
FB MH1608HL600-T
FB MH1608HL121-T
FB MH1608HL221-T
FB MH1608HL331-T
FB MH1608HL471-T
FB MH1608HL601-T
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
47
60
100
150
220
330
470
600
1000
30
60
120
220
330
470
600
Impedance tolerance
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
±25％
●FB MH2012
FB
FB
FB
FB
Parts number
EHS
MH2012HM800-T
MH2012HM121-T
MH2012HM221-T
MH2012HM331-T
RoHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
80
120
220
330
Impedance tolerance
±25％
±25％
±25％
±25％
●FB MH2016
Parts number
FB MH2016HM121NT
FB MH2016HM251NT
EHS
RoHS
RoHS
Nominal impedance
（Ω）
120
250
Impedance tolerance
±30％
±30％
●FB MH3216
Parts number
FB MH3216HM221NT
FB MH3216HM501NT
EHS
RoHS
RoHS
Nominal impedance
（Ω）
220
500
Impedance tolerance
±30％
±30％
●FB MH3225
Parts number
FB MH3225HM601NT
FB MH3225HM102NT
FB MH3225HM202NT
EHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
600
1000
2000
Impedance tolerance
±30％
±30％
±30％
chipbeads_e-E02R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
110
14
■PARTS NUMBER
●FB MH4516
Parts number
FB MH4516HM851NT
EHS
RoHS
Nominal impedance
（Ω）
850
Impedance tolerance
±30％
Measuring frequency
［MHz］
100
DC Resistance
［Ω］（max.）
0.100
Rated current
［A］（max.）
1.5
Thickness
［mm］
1.6 ±0.2
Measuring frequency
［MHz］
100
100
DC Resistance
［Ω］（max.）
0.060
0.130
Rated current
［A］（max.）
3.0
2.0
Thickness
［mm］
2.5 ±0.3
2.5 ±0.3
Measuring frequency
［MHz］
100
100
100
DC Resistance
［Ω］（max.）
0.028
0.060
0.130
Rated current
［A］（max.）
4.0
3.0
1.3
Thickness
［mm］
3.2 ±0.3
3.2 ±0.3
3.2 ±0.3
Measuring frequency
［MHz］
100
100
100
100
DC Resistance
［Ω］（max.）
0.004
0.006
0.004
0.006
Rated current
［A］（max.）
7.5
6.0
7.5
6.0
Thickness
［mm］
0.8 ±0.2
0.8 ±0.2
0.8 ±0.2
0.8 ±0.2
●FB MH4525
Parts number
FB MH4525HM102NT
FB MH4525HM162NT
EHS
RoHS
RoHS
Nominal impedance
（Ω）
1000
1600
Impedance tolerance
±30％
±30％
●FB MH4532
Parts number
FB MH4532HM681-T
FB MH4532HM132-T
FB MH4532HM202-T
EHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
680
1300
2000
Impedance tolerance
±25％
±25％
±25％
●High current type
Parts number
MJ1608HS220NTR
MJ1608HS280NTR
MJ1608HM180NTR
MJ1608HM230NTR
RoHS
RoHS
RoHS
RoHS
Nominal impedance
（Ω）
22
28
18
23
Impedance tolerance
±30％
±30％
±30％
±30％
／ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
FB
FB
FB
FB
EHS
chipbeads_e-E02R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
14
111
■ ELECTRICAL CHARACTERISTICS
■ FB MJ1608
■ FB MJ2125
■ FB MJ3216
／ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
FB MJ3216HL160NT
70
60
50
40
30
20
10
0
■ FB MJ4516
FB MJ4516HL230NT
100
90
80
70
60
50
40
30
20
10
0
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
112
14
■ ELECTRICAL CHARACTERISTICS
Standard type
■ FB MH1608
FB MH1608HM470-T
200
FB MH1608HM600-T
200
180
180
160
160
160
140
140
140
120
120
120
100
100
100
80
80
Z
60
X
20
0
1
10
600
100
10000
FB MH1608HM221-T
0
1
10
500
100
1000
10000
400
400
R
200
10
100
1000
10000
FB MH1608HM102-T
1600
1200
Z
1000
800
10
100
1200
1000
1000
10000
FB MH1608HL300-T
200
100
1000
10000
Z
R
R
X
10
100
1000
10
100
1000
10000
0
1
R
X
10
100
1000
10000
FB MH1608HL121-T
600
Z
400
R
150
300
100
200
300
0
1
10
100
1000
10000
FB MH1608HL471-T
1000
10000
0
10
100
1000
10000
FB MH1608HL601-T
2500
Z
1200
Z
R
Z
1500
R
1000
800
R
1000
600
X
400
X
200
100
0
1
2000
1400
400
X
200
X
1800
600
400
R
100
2000
800
Z
100
Z
500
FB MH1608HL331-T
1000
R
10
FB MH1608HM601-T
200
10000
1600
700
0
1
10000
X
1200
800
500
1000
400
50
X
0
1
1400
900
600
100
600
FB MH1608HL600-T
300
10
800
Z
0
1
250
X
FB MH1608HL221-T
1000
1400
200
150
100
1600
1200
400
1000
X
0
1
1400
250
R
200
10
10000
FB MH1608HM471-T
200
0
1
50
0
1
1000
Z
600
400
X
300
1400
100
600
100
X
10
800
R
200
100
0
1
Z
300
Z
0
1
500
X
200
1
10
100
1000
10000
0
1
10
100
1000
10000
0
1
10
100
1000
10000
■ FBMH2012
FB MH2012HM800-T
400
400
FB MH2012HM121-T
350
350
300
300
300
250
250
250
200
200
200
150
100
10
100
1000
10000
0
1
100
1000
10000
■ FB MH2016
200
400
R
X
200
X
0
1
10
100
1000
10000
0
1
10
100
1000
10000
■ FB MH3216
FB MH2016HM121NT
800
FB MH2016HM251NT
350
180
FB MH3216HM221NT
800
FB MH3216HM501NT
300
160
600
120
200
Z
100
R
400
Z
60
X
100
1000
10000
0
1
10
Z
400
R
100
X
100
200
50
X
20
R
R
200
40
Z
150
80
10
600
250
140
0
1
Z
R
50
X
10
FB MH2012HM331-T
600
Z
100
50
X
800
150
R
100
R
50
0
1
Z
150
Z
FB MH2012HM221-T
400
350
／ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
300
R
100
X
1600
500
Z
200
20
FB MH1608HM331-T
600
300
R
40
X
20
1000
400
Z
60
R
40
FB MH1608HM151-T
600
500
80
Z
60
R
40
FB MH1608HM101-T
200
180
1000
0
1
X
10
100
1000
10000
0
1
10
100
1000
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
14
113
■ ELECTRICAL CHARACTERISTICS
Standard type
■ FB MH3225
1200
■ FB MH4516
FB MH3225HM601NT
1200
1000
1000
800
800
600
600
Z
400
1200
2500
Z
R
Z
1000
100
400
0
1
10
100
1000
0
1
10
100
0
1
1000
10
100
1000
■ FB MH4532
FB MH4525HM102NT
FB MH4525HM162NT
FB MH4532HM681-T
FB M4532HM132-T
／ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
1800
1800
1800
1800
1600
1600
1600
1600
1400
1400
1400
1400
1000
1000
1000
1000
1200
1200
1200
1200
Z
800
R
Z
800
R
600
800
600
400
10
100
0
Z
400
X
200
1000
800
600
400
X
200
1
X
200
X
■ FB MH4525
0
Z
600
500
X
200
1000
R
800
1500
R
FB MH4516HM851NT
1000
2000
400
X
10
FB MH3225HM202NT
R
200
0
1
FB MH3225HM102NT
R
200
1
10
100
1000
0
400
10
100
X
200
X
1
R
Z
600
0
1000
1
10
100
1000
■ High current type
FB M4532HM202-T
2500
30
FB MJ1608HS220NTR
40
FB J1608HM180NTR
35
25
2000
30
20
1500
Z
25
Z
1000
Z
20
R
15
R
R
15
10
10
500
X
5
0
1
10
100
1000
0
1
10
100
X
5
X
1000
0
1
10000
10
100
1000
10000
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
114
14
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE)
■PACKAGING
①Minimum Quantity
Standard Quantity［pcs］
Paper Tape
Embossed Tape
4000
－
4000
－
4000
－
－
2000
－
2000
－
1000
－
2000
－
1000
－
2000
Type
1608（0603）
2125（0805）
2012（0805）
2016（0806）
3216（1206）
3225（1210）
4516（1806）
4525（1810）
4532（1812）
②Tape Material
●Card board carrier tape
Top tape
Base tape
Chip Filled
Sprocket hole
Bottom tape
Chip cavity
Chip
●Embossed tape
Top tape
Chip Filled
Sprocket hole
Base tape
Chip cavity
Chip
③Taping Dimensions
●Paper tape (0.315 inches wide)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E02R01
A
Chip Cavity
B
Insertion Pitch
F
Tape Thickness
T
1.0±0.2
（0.039±0.008）
1.8±0.2
（0.071±0.008）
4.0±0.2
（0.157±0.008）
1.1max
（0.043max）
1.5±0.2
（0.059±0.008）
2.3±0.2
（0.091±0.008）
4.0±0.2
（0.157±0.008）
1.1max
（0.043max）
Type
FBMJ1608
FBMH1608
（0603）
FBMJ2125
FBMH2012
（0805）
Unit : mm（inch）
●Embossed tape (0.315 inches wide)
Type
FBMH2016
（0806）
FBMJ3216
（1206）
FBMH3216
（1206）
FBMH3225
（1210）
Chip Cavity
A
B
1.8±0.2
2.2±0.2
（0.071±0.008）
（0.087±0.008）
1.9±0.2
3.5±0.2
（0.075±0.008）
（0.138±0.008）
1.9±0.2
3.5±0.2
（0.075±0.008）
（0.138±0.008）
2.8±0.2
3.5±0.2
（0.110±0.008）
（0.138±0.008）
Insertion Pitch
F
4.0±0.2
（0.157±0.008）
4.0±0.2
（0.157±0.008）
4.0±0.2
（0.157±0.008）
4.0±0.2
（0.157±0.008）
Tape Thickness
K
T
2.6max
0.6max
（0.102max）
（0.024max）
1.5max
0.3max
（0.059max）
（0.012max）
2.6max
0.6max
（0.102max）
（0.024max）
4.0max
0.6max
（0.157max）
（0.024max）
Unit : mm（inch）
Insertion Pitch
F
4.0±0.2
（0.157±0.008）
4.0±0.2
（0.157±0.008）
4.0±0.2
（0.157±0.008）
8.0±0.2
（0.315±0.008）
Tape Thickness
K
T
1.5max
0.3max
（0.059max）
（0.012max）
2.6max
0.6max
（0.102max）
（0.024max）
4.0max
0.6max
（0.157max）
（0.024max）
4.0max
0.6max
（0.157max）
（0.024max）
Unit : mm（inch）
●Embossed tape (0.472 inches wide)
Type
FBMJ4516
（1806）
FBMH4516
（1806）
FBMH4525
（1810）
FBMH4532
（1812）
Chip Cavity
A
B
1.9±0.2
4.9±0.2
（0.075±0.008）
（0.193±0.008）
1.9±0.2
4.9±0.2
（0.075±0.008）
（0.193±0.008）
2.9±0.2
4.9±0.2
（0.114±0.008）
（0.193±0.008）
3.6±0.2
4.9±0.2
（0.142±0.008）
（0.193±0.008）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E02R01
④Leader and Blank portion
⑤Reel size
2.0±0.5
（0.079±0.020）
t
φ13.0±0.5
（φ0.512±0.020）
R1.0
φd
φ21.0±0.8
（φ0.827±0.031）
φD
W
Type
FBMJ1608
FBMJ2125
FBMJ3216
φD
φd
FBMH4532
t
10.0±1.5
（0.394±0.059）
14.0±1.5
（0.551±0.059）
FBMJ4516
FBMH1608
FBMH2012
FBMH2016
FBMH3216
FBMH3225
FBMH4516
FBMH4525
W
180＋0/－3
（7.09＋0/－0.118 ）
330±2.0
（12.99±0.080）
60＋1/－0
（2.36＋0.039/－0 ）
100±1.0
（3.94±0.039）
10.0±1.5
（0.394±0.059）
14.0±1.5
（0.551±0.059）
14.0±2.0
（0.551±0.080）
2.5max
(0.098max)
3.0max
(1.181max)
Unit : mm（inch）
⑥Top tape strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E02R01
CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE)
■RELIABILITY DATA
1. Operating Temperature Range
Specified Value
－40℃～＋125℃
Including self-generated heat
2. Storage Temperature Range
Specified Value
－40℃～＋85℃
Test Methods and
Remarks
*Note: -5 to ＋40℃ in taped packaging
3. Impedance
Specified Value
Within the specified tolerance
Test Methods and
Remarks
Measuring equipment
Measuring frequency
: Impedance analyzer (HP4291A) or its equivalent
: 100±1 MHz
4. DC Resistance
Specified Value
Within the specified range
Test Methods and
Remarks
Four-terminal method
Measuring equipment : Milliohm High-Tester 3226 (Hioki Denki) or its equivalent
5. Rated Current
Specified Value
Within the specified range
6. Vibration
Specified Value
Appearance
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
According to JIS C 0040.
Vibration type
:A
Time
: 2 hrs each in X,Y, and Z directions Total: 6 hrs
Frequency range
: 10 to 55 to 10Hz (/min.)
Amplitude
: 1.5 mm (shall not exceed acceleration 196m/s2)
Mounting method
: Soldering onto PC board
7. Solderability
Specified Value
90% or more of immersed surface of terminal electrode shall be covered with fresh solder.
Test Methods and
Remarks
Solder temperature
Immersion time
Preconditioning
Immersion and Removal speed
:
:
:
:
230±5℃
4±1 sec.
Immersion into flux.
25mm/sec.
8. Resistance to Soldering Heat
Specified Value
Appearance
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
Preheating
Resistance to Soldering Heat
Duration
Preconditioning
Immersion and Removal speed
Recovery
:
:
:
:
:
:
150℃ for 3 min.
260±5℃
10±0.5 sec.
Immersion into flux.
25mm/sec.
2 to 3 hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E02R01
9. Thermal Shock
Specified Value
Test Methods and
Remarks
Appearance
Impedance change
: No significant abnormality
: Within＋50/－10% of the initial value
According to JIS C 0025.
Conditions for 1 cycle
Step
Temperature (℃)
1
－40±3℃
2
Room Temperature
3
85±2℃
4
Room Temperature
Number of cycles
Mounting method
Recovery
Duration (min.)
30±3
Within 3
30±3
Within 3
: 100
: Soldering onto PC board
: 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
10. Resistance to Humidity (steady state)
Specified Value
Appearances
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
Temperature
Humidity
Duration
Mounting method
Recovery
: 40±2℃
: 90 to 95% RH
: 500＋24/－0
: Soldering onto PC board
: 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
11. Loading under Damp Heat
Specified Value
Appearance
Impedance change
Test Methods and
Remarks
Temperature
Humidity
Applied current
Duration
Mounting method
Recovery
No significant abnormality
Within ±30% of the initial value
: 40±2℃
: 90 to 95%RH
: Rated current
: 500＋24/－0 hrs
: Soldering onto PC board
: 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
12. High Temperature Loading Test
Specified Value
Appearance
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
Temperature
Duration
Applied current
Mounting method
Recovery
:
:
:
:
:
85±2℃
500＋24/－0 hrs
Rated current
Soldering onto PC board
2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
13. Bending Strength
Specified Value
Appearance : No mechanical damage.
Warp
Testing board
Thickness
: 2mm
: Glass epoxy-resin substrate
: 0.8mm
Test Methods and
Remarks
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E02R01
14. Adhesion of Electrode
Specified Value
No separation or indication of separation of electrode.
Applied force
Duration
: 5N
: 10 sec.
Test Methods and
Remarks
Note on standard condition: "standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity and 86 to 106kPa of air
pressure. Unless otherwise specified, all the tests are conducted under the "standard condition."
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E02R01
CHIP BEAD INDUCTORS FOR POWER LINE （FB SERIES M TYPE）
■PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
◆Rated current
1. Rated current of this product is shown in this catalogue, but please be sure to have the base board designed with adequate inspection in
case of the generation of heat becomes high within the rated current range when the base board is in high resistance or in bad heating
conditions.
2. PCB Design
Precautions
◆Land pattern design
1. Please refer to a recommended land pattern.
3. Considerations for automatic placement
Precautions
Technical
considerations
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, etc. sufficiently.
◆Preheating when soldering
Heating : The temperature difference between soldering and remaining heat should not be greater than 150℃.
Cooling : The temperature difference between the components and cleaning process should not be greater than 100℃.
◆Recommended conditions for using a soldering iron
Put the soldering iron on the land-pattern.
Soldering iron's temperature - Below 350℃
Duration - 3 seconds or less
The soldering iron should not directly touch the inductor.
◆Wave, Reflow, Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
【Recommended reflow condition】
Technical
considerations
◆Preheating when soldering
1. There is a case that products get damaged by a heat shock.
◆Recommended conditions for using a soldering iron
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_prec_e-E02R01
5. Handling
Precautions
Technical
considerations
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Setting PC boards
1. When setting a chip mounted base board, please make sure that there is no residual stress to the chip by distortion in the board or at
screw part.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the
board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Setting PC boards
1. There is a case that a characteristic varies with residual stress.
◆Breakaway PC boards (splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
6. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
・Recommended conditions
Ambient temperature 0～40℃
Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within 6 months from the time of delivery.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_prec_e-E02R01