MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER DESCRIPTION The 3851 group is the 8-bit microcomputer based on the 740 family core technology. The 3851 group is designed for the household products and office automation equipment and includes serial I/O functions, 8-bit timer, A-D converter, and I2 C-bus interface. FEATURES ●Basic machine-language instructions ...................................... 71 ●Minimum instruction execution time .................................. 0.5 µs (at 8 MHz oscillation frequency) ●Memory size ROM ............................................................................. 16 Kbytes RAM .............................................................................. 512 bytes ●Programmable input/output ports ............................................ 34 ●Interrupts ................................................. 16 sources, 16 vectors ●Timers ............................................................................. 8-bit ✕ 4 ●Serial I/O ....................... 8-bit ✕ 1(UART or Clock-synchronized) ●Multi-master I2 C-bus interface (option) ....................... 1 channel ●PWM ............................................................................... 8-bit ✕ 1 ●A-D converter ............................................... 10-bit ✕ 5 channels ●Watchdog timer ............................................................ 16-bit ✕ 1 ●Clock generating circuit ..................................... Built-in 2 circuits (connect to external ceramic resonator or quartz-crystal oscillator) ●Power source voltage In high-speed mode .................................................. 4.0 to 5.5 V (at 8 MHz oscillation frequency) In high-speed mode .................................................. 2.7 to 5.5 V (at 4 MHz oscillation frequency) In middle-speed mode ............................................... 2.7 to 5.5 V (at 8 MHz oscillation frequency) In low-speed mode .................................................... 2.7 to 5.5 V (at 32 kHz oscillation frequency) ●Power dissipation In high-speed mode .......................................................... 34 mW (at 8 MHz oscillation frequency, at 5 V power source voltage) In low-speed mode ............................................................ 60 µW (at 32 kHz oscillation frequency, at 3 V power source voltage) ●Operating temperature range.................................... –20 to 85°C APPLICATION Office automation equipment, FA equipment, Household products, Consumer electronics, etc. PIN CONFIGURATION (TOP VIEW) 1 42 2 41 3 40 4 39 5 38 6 37 7 8 9 10 11 12 13 14 15 16 M38513M4-XXXFP M38513M4-XXXSP VCC VREF AVSS P44/INT3/PWM P43/INT2 P42/INT1 P41/INT0 P40/CNTR1 P27/CNTR0/SRDY P26/SCLK P25/SCL2/TxD P24/SDA2/RxD P23/SCL1 P22/SDA1 CNVSS P21/XCIN P20/XCOUT RESET XIN XOUT VSS 36 35 34 33 32 31 30 29 28 27 17 26 18 25 19 24 20 23 21 22 P30/AN0 P31/AN1 P32/AN2 P33/AN3 P34/AN4 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13/(LED0) P14/(LED1) P15/(LED2) P16/(LED3) P17/(LED4) Package type : FP ........................... 42P2R-A (42-pin plastic-molded SSOP) Package type : SP ........................... 42P4B (42-pin shrink plastic-molded DIP) Fig. 1 M38513M4-XXXFP/SP pin configuration 2 Fig. 2 Functional block diagram Sub-clock Sub-clock input output XCIN XCOUT 3 AVSS VREF 2 A-D converter (10) PWM (8) Reset Clock generating circuit 20 Main-clock output XOUT Watchdog timer 19 Main-clock input XIN I/O port P4 4 5 6 7 8 P4(5) RAM FUNCTIONAL BLOCK DIAGRAM INT0– INT3 ROM I/O port P3 38 39 40 41 42 P3(5) 21 VSS PC H A SI/O(8) PS 2 I C PC L S Y X 18 C P U RESET 1 CNTR0 Reset input VCC P2(8) CNTR1 I/O port P2 XCOUT XCIN Prescaler Y(8) Prescaler X(8) Prescaler 12(8) 9 10 11 12 13 14 16 17 15 CNVSS I/O port P1 22 23 24 25 26 27 28 29 P1(8) P0(8) I/O port P0 30 31 32 3334 35 36 37 Timer Y( 8 ) Timer X( 8 ) Timer 2( 8 ) Timer 1( 8 ) MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FUNCTIONAL BLOCK MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PIN DESCRIPTION Table 1 Pin description Pin Name VCC, VSS Power source CNV SS CNVSS input RESET Reset input XIN Clock input XOUT Clock output P00 –P07 I/O port P0 P10 –P17 I/O port P1 P20 /XCOUT P21 /XCIN P22 /SDA1 P23 /SCL1 P24 /SDA2/RxD P25 /SCL2/TxD P26 /SCLK P27 /CNTR0 / SRDY I/O port P2 Functions Function except a port function •Apply voltage of 2.7 V – 5.5 V to Vcc, and 0 V to Vss. •This pin controls the operation mode of the chip. •Normally connected to VSS . •Reset input pin for active “L.” •Input and output pins for the clock generating circuit. •Connect a ceramic resonator or quartz-crystal oscillator between the X IN and XOUT pins to set the oscillation frequency. •When an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open. •8-bit CMOS I/O port. •I/O direction register allows each pin to be individually programmed as either input or output. •CMOS compatible input level. •CMOS 3-state output structure. •P1 3 to P17 (5 bits) are enabled to output large current for LED drive. •8-bit CMOS I/O port. •I/O direction register allows each pin to be individually programmed as either input or output. •CMOS compatible input level. •P22 to P2 5 can be switched between CMOS compatible input level or SMBUS input level in the I2C-BUS interface function. •P20, P21, P24 to P27 : CMOS3-state output structure. •P24, P2 5 : N-channel open-drain structure in the I2 CBUS interface function. • Sub-clock generating circuit I/O pins (connect a resonator) • I2 C-BUS interface function pins • I2 C-BUS interface function pin/ Serial I/O function pins • Serial I/O function pin • Serial I/O function pin/ Timer X function pin •P22, P23: N-channel open-drain structure. P30 /AN0– P34 /AN4 P40 /CNTR1 P41 /INT0 – P43 /INT2 P44 /INT3 /PWM I/O port P3 I/O port P4 •8-bit CMOS I/O port with the same function as port P0. •CMOS compatible input level. •CMOS 3-state output structure. •8-bit CMOS I/O port with the same function as port P0. •CMOS compatible input level. •CMOS 3-state output structure. • A-D converter input pin • Timer Y function pin • Interrupt input pins • Interrupt input pin • PWM output pin 3 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GROUP EXPANSION Packages Mitsubishi plans to expand the 3851 group as follows: 42P2R-A ............................................ 42-pin plastic molded SSOP 42P4B ......................................... 42-pin shrink plastic-molded DIP Memory Type Support for mask ROM and One Time PROM versions. Memory Size ROM/PROM size ............................................................ 16 K bytes RAM size ......................................................................... 512 bytes Memory Expansion Plan ROM size (bytes) 48K 32K 28K Under development M38514E6FP/SP M38514M6-XXXFP/SP 24K 20K Mass production M38513E4FP/SP M38513M4-XXXFP/SP 16K 12K 8K 128 192 256 384 512 RAM size (bytes) Fig. 3 Memory expansion plan 4 640 768 896 1024 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FUNCTIONAL DESCRIPTION CENTRAL PROCESSING UNIT (CPU) The 3851 group uses the standard 740 Family instruction set. Refer to the table of 740 Family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction set. Machine-resident 740 Family instructions are as follows: The FST and SLW instructions cannot be used. The STP, WIT, MUL, and DIV instructions can be used. [CPU Mode Register (CPUM)] 003B16 The CPU mode register contains the stack page selection bit, etc. The CPU mode register is allocated at address 003B 16. b7 b0 CPU mode register (CPUM : address 003B16) Processor mode bits b1 b0 0 0 : Single-chip mode 0 1 : 1 0 : Not available 1 1 : Stack page selection bit 0 : 0 page 1 : 1 page Not used (return “1” when read) (Do not write “0” to this bit.) Port X C switch bit 0 : I/O port function (stop oscillating) 1 : X CIN–XCOUT oscillating function Main clock (X IN–XOUT ) stop bit 0 : Oscillating 1 : Stopped Main clock division ratio selection bits b7 b6 0 0 : φ = f(X IN)/2 (high-speed mode) 0 1 : φ = f(X IN)/8 (middle-speed mode) 1 0 : φ = f(X CIN)/2 (low-speed mode) 1 1 : Not available Fig. 4 Structure of CPU mode register 5 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MEMORY Special Function Register (SFR) Area Zero Page Access to this area with only 2 bytes is possible in the zero page addressing mode. The Special Function Register area in the zero page contains control registers such as I/O ports and timers. Special Page RAM Access to this area with only 2 bytes is possible in the special page addressing mode. RAM is used for data storage and for stack area of subroutine calls and interrupts. ROM The first 128 bytes and the last 2 bytes of ROM are reserved for device testing and the rest is user area for storing programs. Interrupt Vector Area The interrupt vector area contains reset and interrupt vectors. RAM area RAM size (bytes) Address XXXX16 192 256 384 512 640 768 896 1024 1536 2048 3072 4032 00FF16 013F16 01BF16 023F16 02BF16 033F16 03BF16 043F16 063F16 083F16 0C3F16 0FFF16 000016 SFR area RAM 010016 XXXX16 Reserved area 044016 Not used YYYY16 ROM area Reserved ROM area ROM size (bytes) Address YYYY16 Address ZZZZ16 4096 8192 12288 16384 20480 24576 28672 32768 36864 40960 45056 49152 53248 57344 61440 F00016 E00016 D00016 C00016 B00016 A00016 900016 800016 700016 600016 500016 400016 300016 200016 100016 F08016 E08016 D08016 C08016 B08016 A08016 908016 808016 708016 608016 508016 408016 308016 208016 108016 Fig. 5 Memory map diagram 6 Zero page 004016 (128 bytes) ZZZZ16 ROM FF0016 FFDC16 Interrupt vector area FFFE16 FFFF16 Reserved ROM area Special page MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 000016 Port P0 (P0) 002016 Prescaler 12 (PRE12) 000116 Port P0 direction register (P0D) 002116 Timer 1 (T1) 000216 Port P1 (P1) 002216 Timer 2 (T2) 000316 Port P1 direction register (P1D) 002316 Timer XY mode register (TM) 000416 Port P2 (P2) 002416 Prescaler X (PREX) 000516 Port P2 direction register (P2D) 002516 Timer X (TX) 000616 Port P3 (P3) 002616 Prescaler Y (PREY) 000716 Port P3 direction register (P3D) 002716 Timer Y (TY) 000816 Port P4 (P4) 002816 Timer count source selection register (TCSS) 000916 Port P4 direction register (P4D) 002916 000A16 002A16 000B16 002B16 I2C data shift register (S0) 000C16 002C16 I2C address register (S0D) 000D16 002D16 I2C status register (S1) 000E16 002E16 I2C control register (S1D) 000F16 002F16 I2C clock control register (S2) 001016 003016 I2C start/stop condition control register (S2D) 001116 003116 001216 003216 001316 003316 001416 003416 A-D control register (ADCON) 001516 Reserved ✽ 003516 A-D conversion low-order register (ADL) 001616 Reserved ✽ 003616 A-D conversion high-order register (ADH) 001716 Reserved ✽ 003716 001816 Transmit/Receive buffer register (TB/RB) 003816 001916 Serial I/O status register (SIOSTS) 003916 Watchdog timer control register (WDTCON) 001A16 Serial I/O control register (SIOCON) 003A16 Interrupt edge selection register (INTEDGE) 001B16 UART control register (UARTCON) 003B16 CPU mode register (CPUM) 001C16 Baud rate generator (BRG) 003C16 Interrupt request register 1 (IREQ1) 001D16 PWM control register (PWMCON) 003D16 Interrupt request register 2 (IREQ2) 001E16 PWM prescaler (PREPWM) 003E16 Interrupt control register 1 (ICON1) 001F16 PWM register (PWM) 003F16 Interrupt control register 2 (ICON2) MISRG ✽ Reserved : Do not write “1” to this address. Fig. 6 Memory map of special function register (SFR) 7 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER I/O PORTS The I/O ports have direction registers which determine the input/ output direction of each individual pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input port or output port. When “0” is written to the bit corresponding to a pin, that pin becomes an input pin. When “1” is written to that bit, that pin becomes an output pin. If data is read from a pin which is set to output, the value of the port output latch is read, not the value of the pin itself. Pins set to input are floating. If a pin set to input is written to, only the port output latch is written to and the pin remains floating. Table 2 I/O port function Pin Name P00–P07 Port P0 P10 –P17 Port P1 Input/Output CMOS compatible input level CMOS 3-state output P20 /XCOUT P21 /XCIN Non-Port Function Related SFRs Ref.No. (1) Sub-clock generating circuit CPU mode register (2) (3) I 2C-BUS interface function I/O I 2C control register (4) (5) I 2C-BUS interface function I/O Serial I/O function I/O I 2C control register Serial I/O control register (6) (7) P26 /SCLK Serial I/O function I/O Serial I/O control register (8) P27 /CNTR0 /SRDY Serial I/O function I/O Timer X function I/O Serial I/O control register Timer XY mode register (9) A-D conversion input A-D control register (10) Timer Y function I/O Timer XY mode register (11) External interrupt input Interrupt edge selection register (12) External interrupt input PWM output Interrupt edge selection register PWM control register (13) P22 /SDA1 P23 /SCL1 Port P2 P24 /SDA2/RxD P25 /SCL2/TxD P30 /AN0— P34 /AN4 P40/CNTR 1 P41 /INT0 — P43 /INT2 P44 /INT3 /PWM 8 I/O Structure Input/output, individual bits Port P3 CMOS compatible input level CMOS/SMBUS input level (when selecting I 2C-BUS interface function) N-channel open-drain output CMOS compatible input level CMOS/SMBUS input level (when selecting I 2C-BUS interface function) CMOS 3-state output N-channel open-drain output (when selecting I 2C-BUS interface function) CMOS compatible input level CMOS 3-state output Port P4 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (2) Port P20 (1) Port P0, P1 Port XC switch bit Direction register Data bus Direction register Port latch Data bus Port latch Oscillator Port P21 (3) Port P21 Port XC switch bit Port XC switch bit Direction register (4) Port P22 I2 C-BUS interface enable bit SDA/SCL pin selection bit Data bus Port latch Direction register Data bus Port latch Sub-clock generating circuit input SDA output (5) Port P23 SDA input I 2 C-BUS interface enable bit SDA/SCL pin selection bit (6) Port P24 Direction register Data bus I 2 C-BUS interface enable bit SDA/SCL pin selection bit Serial I/O enable bit Receive enable bit Port latch Direction register Data bus Port latch SCL output SCL input (7) Port P25 SDA output P-channel output disable bit SDA input Serial I/O input Serial I/O enable bit Transmit enable bit I2C bus interface enable bit SDA/SCL pin selection bit (8) Port P26 Serial I/O enable bit Serial I/O clock selection bit Direction register Serial I/O mode selection bit Data bus Port latch Serial I/O enable bit Direction register Data bus Port latch SCL input Serial I/O output SCL output Serial clock output External clock input Fig. 7 Port block diagram (1) 9 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (9) Port P27 (10) Port P30–P34 Pulse output mode Serial I/O mode selection bit Serial I/O enable bit SRDY output enable bit Direction register Data bus Direction register Data bus Port latch Port latch A-D converter input Analog input pin selection bit Pulse output mode Serial ready output CNTR0 interrupt input (12) Port P41–P43 Direction register Timer output Data bus Port latch (11) Port P40 Direction register Interrupt input Data bus Port latch Pulse output mode Timer output CNTR1 interrupt input (13) Port P44 PWM output enable bit Direction register Data bus Port latch PWM output Fig. 8 Port block diagram (2) 10 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER INTERRUPTS ■Notes Interrupts occur by 16 sources among 16 sources: seven external, eight internal, and one software. When the active edge of an external interrupt (INT0–INT3, SCL/ SDA, CNTR0, CNTR1) is set, the corresponding interrupt request bit may also be set. Therefore, take the following sequence: Interrupt Control Each interrupt is controlled by an interrupt request bit, an interrupt enable bit, and the interrupt disable flag except for the software interrupt set by the BRK instruction. An interrupt occurs if the corresponding interrupt request and enable bits are “1” and the interrupt disable flag is “0”. Interrupt enable bits can be set or cleared by software. Interrupt request bits can be cleared by software, but cannot be set by software. The BRK instruction cannot be disabled with any flag or bit. The I (interrupt disable) flag disables all interrupts except the BRK instruction interrupt. When several interrupts occur at the same time, the interrupts are received according to priority. 1. Disable the interrupt 2. Change the interrupt edge selection register (SCL/SDA interrupt pin polarity selection bit for SCL/SDA; the timer XY mode register for CNTR0 and CNTR 1) 3. Clear the interrupt request bit to “0” 4. Accept the interrupt. Interrupt Operation By acceptance of an interrupt, the following operations are automatically performed: 1. The contents of the program counter and the processor status register are automatically pushed onto the stack. 2. The interrupt disable flag is set and the corresponding interrupt request bit is cleared. 3. The interrupt jump destination address is read from the vector table into the program counter. 11 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 3 Interrupt vector addresses and priority Interrupt Source Reset (Note 2) Priority 1 Vector Addresses (Note 1) High Low FFFD 16 FFFC 16 Interrupt Request Generating Conditions Remarks At reset Non-maskable External interrupt (active edge selectable) INT0 2 FFFB16 FFFA16 At detection of either rising or falling edge of INT0 input SCL, SDA 3 FFF916 FFF816 At detection of either rising or falling edge of SCL or SDA input External interrupt (active edge selectable) INT1 4 FFF716 FFF616 At detection of either rising or falling edge of INT1 input External interrupt (active edge selectable) INT2 5 FFF516 FFF416 At detection of either rising or falling edge of INT2 input External interrupt (active edge selectable) INT3 6 FFF316 FFF216 At detection of either rising or falling edge of INT3 input External interrupt (active edge selectable) I 2C Timer X Timer Y Timer 1 Timer 2 7 8 9 FFF116 FFEF16 FFED16 10 11 FFEB16 FFE916 FFF016 FFEE 16 FFEC 16 FFEA 16 FFE816 Serial I/O reception 12 FFE716 FFE616 At completion of serial I/O data reception Valid when serial I/O is selected Serial I/O Transmission 13 FFE516 FFE416 At completion of serial I/O transfer shift or when transmission buffer is empty Valid when serial I/O is selected CNTR 0 14 FFE316 FFE216 At detection of either rising or falling edge of CNTR0 input External interrupt (active edge selectable) CNTR 1 15 FFE116 FFE016 At detection of either rising or falling edge of CNTR1 input External interrupt (active edge selectable) A-D converter BRK instruction 16 FFDF 16 FFDE 16 At completion of A-D conversion 17 FFDD16 FFDC16 At BRK instruction execution At completion of data transfer At timer X underflow At timer Y underflow At timer 1 underflow Notes 1: Vector addresses contain interrupt jump destination addresses. 2: Reset function in the same way as an interrupt with the highest priority. 12 STP release timer underflow At timer 2 underflow Non-maskable software interrupt MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Interrupt request bit Interrupt enable bit Interrupt disable flag (I) BRK instruction Reset Interrupt request Fig. 9 Interrupt control b7 b0 Interrupt edge selection register (INTEDGE : address 003A16) INT0 active edge selection bit INT1 active edge selection bit INT2 active edge selection bit INT3 active edge selection bit Not used (returns “0” when read) 0 : Falling edge active 1 : Rising edge active b7 b0 Interrupt request register 1 (IREQ1 : address 003C16) b7 b0 Interrupt request register 2 (IREQ2 : address 003D16) INT0 interrupt request bit SCL/SDA interrupt request bit INT1 interrupt request bit INT2 interrupt request bit INT3 interrupt request bit I2C interrupt request bit Timer X interrupt request bit Timer Y interrupt request bit Timer 1 interrupt request bit Timer 2 interrupt request bit Serial I/O reception interrupt request bit Serial I/O transmit interrupt request bit CNTR0 interrupt request bit CNTR1 interrupt request bit AD converter interrupt request bit Not used (returns “0” when read) 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued b7 b0 Interrupt control register 1 (ICON1 : address 003E16) INT0 interrupt enable bit SCL/SDA interrupt enable bit INT1 interrupt enable bit INT2 interrupt enable bit INT3 interrupt enable bit I2C interrupt enable bit Timer X interrupt enable bit Timer Y interrupt enable bit 0 : Interrupts disabled 1 : Interrupts enabled b7 b0 Interrupt control register 2 (ICON2 : address 003F16) Timer 1 interrupt enable bit Timer 2 interrupt enable bit Serial I/O reception interrupt enable bit Serial I/O transmit interrupt enable bit CNTR0 interrupt enable bit CNTR1 interrupt enable bit AD converter interrupt enable bit Not used (returns “0” when read) (Do not write “1” to this bit) 0 : Interrupts disabled 1 : Interrupts enabled Fig. 10 Structure of interrupt-related registers (1) 13 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TIMERS Timer 1 and Timer 2 The 3851 group has four timers: timer X, timer Y, timer 1, and timer 2. The division ratio of each timer or prescaler is given by 1/(n + 1), where n is the value in the corresponding timer or prescaler latch. All timers are count down. When the timer reaches “00 16”, an underflow occurs at the next count pulse and the corresponding timer latch is reloaded into the timer and the count is continued. When a timer underflows, the interrupt request bit corresponding to that timer is set to “1”. The count source of prescaler 12 is the oscillation frequency divided by 16. The output of prescaler 12 is counted by timer 1 and timer 2, and a timer underflow sets the interrupt request bit. Timer X and Timer Y Timer X and Timer Y can each select in one of four operating modes by setting the timer XY mode register. (1) Timer Mode The timer counts the count source selected by Timer count source selection bit. (2) Pulse Output Mode b0 b7 Timer XY mode register (TM : address 002316) Timer X operating mode bit b1b0 0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR0 active edge selection bit 0: Interrupt at falling edge Count at rising edge in event counter mode 1: Interrupt at rising edge Count at falling edge in event counter mode Timer X count stop bit 0: Count start 1: Count stop Timer Y operating mode bit b5b4 0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR1 active edge selection bit 0: Interrupt at falling edge Count at rising edge in event counter mode 1: Interrupt at rising edge Count at falling edge in event counter mode Timer Y count stop bit 0: Count start 1: Count stop The timer counts the count source selected by Timer count source selection bit. Whenever the contents of the timer reach “0016 ”, the signal output from the CNTR0 (or CNTR1) pin is inverted. If the CNTR0 (or CNTR 1 ) active edge selection bit is “0”, output begins at “ H”. If it is “1”, output starts at “L”. When using a timer in this mode, set the corresponding port P27 ( or port P40 ) direction register to output mode. (3) Event Counter Mode Operation in event counter mode is the same as in timer mode, except that the timer counts signals input through the CNTR0 or CNTR1 pin. When the CNTR0 (or CNTR1 ) active edge selection bit is “0”, the rising edge of the CNTR0 (or CNTR 1) pin is counted. When the CNTR0 (or CNTR1 ) active edge selection bit is “1”, the falling edge of the CNTR0 (or CNTR1) pin is counted. (4) Pulse Width Measurement Mode If the CNTR0 (or CNTR 1) active edge selection bit is “0”, the timer counts the selected signals by the count source selection bit while the CNTR0 (or CNTR1) pin is at “H”. If the CNTR0 (or CNTR 1) active edge selection bit is “1”, the timer counts it while the CNTR 0 (or CNTR1 ) pin is at “L”. Fig. 11 Structure of timer XY mode register b7 b0 Timer count source selection register (TCSS : address 002816) Timer X count source selection bit 0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode) 1 : f(XIN)/2 (f(XCIN)/2 at low-speed mode) Timer Y count source selection bit 0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode) 1 : f(XIN)/2 (f(XCIN)/2 at low-speed mode) Timer 12 count source selection bit 0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode) 1 : f(XCIN) Not used (returns “0” when read) Fig. 12 Structure of timer count source selection register 14 The count can be stopped by setting “1” to the timer X (or timer Y) count stop bit in any mode. The corresponding interrupt request bit is set each time a timer overflows. ■Note When switching the count source by the timer 12, X and Y count source bit, the value of timer count is altered in unconsiderable amount owing to generating of a thin pulses in the count input signals. Therefore, select the timer count source before set the value to the prescaler and the timer. MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Data bus f(XIN)/16 f(XIN)/2 Prescaler X latch (8) Timer X latch (8) Pulse width Timer X count source selection bit measurement Timer mode Pulse output mode mode Prescaler X (8) CNTR0 active edge selection bit “0” P27/CNTR0 Event counter mode “1” Timer X (8) Timer X count stop bit To CNTR0 interrupt request bit CNTR0 active edge selection “1” bit “0” Q Toggle flip-flop T Q R Timer X latch write pulse Pulse output mode Port P27 latch Port P27 direction register To timer X interrupt request bit Pulse output mode Data bus Prescaler Y latch (8) f(XIN)/16 f(XIN)/2 Timer Y count source selection bit Pulse width measurement mode Timer mode Pulse output mode Prescaler Y (8) CNTR1 active edge selection bit “0” P40/CNTR1 Event counter mode “1” Port P40 direction register Timer Y (8) To timer Y interrupt request bit Timer Y count stop bit To CNTR1 interrupt request bit CNTR1 active edge selection “1” bit Q Toggle flip-flop T Q Port P40 latch Timer Y latch (8) “0” R Timer Y latch write pulse Pulse output mode Pulse output mode Data bus Prescaler 12 latch (8) f(XIN)/16 f(XCIN) Prescaler 12 (8) Timer 1 latch (8) Timer 2 latch (8) Timer 1 (8) Timer 2 (8) To timer 2 interrupt request bit Timer 12 count source selection bit To timer 1 interrupt request bit Fig. 13 Block diagram of timer X, timer Y, timer 1, and timer 2 15 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER SERIAL I/O (1) Clock Synchronous Serial I/O Mode Serial I/O can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer is also provided for baud rate generation. Clock synchronous serial I/O mode can be selected by setting the serial I/O mode selection bit of the serial I/O control register (bit 6 of address 001A16) to “1”. For clock synchronous serial I/O, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the TB/RB. Data bus Serial I/O control register Address 001816 Receive buffer register Receive interrupt request (RI) Receive shift register P24/RXD Address 001A16 Receive buffer full flag (RBF) Shift clock Clock control circuit P26/SCLK XIN Serial I/O synchronous clock selection bit Frequency division ratio 1/(n+1) BRG count source selection bit Baud rate generator Address 001C16 1/4 P27/SRDY F/F 1/4 Clock control circuit Falling-edge detector Shift clock P25/TXD Transmit shift register Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Transmit buffer register Transmit buffer empty flag (TBE) Serial I/O status register Address 001916 Address 001816 Data bus Fig. 14 Block diagram of clock synchronous serial I/O Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output TxD D0 D1 D2 D3 D4 D5 D6 D7 Serial input RxD D0 D1 D2 D3 D4 D5 D6 D7 Receive enable signal SRDY Write pulse to receive/transmit buffer register (address 001816) TBE = 0 TBE = 1 TSC = 0 RBF = 1 TSC = 1 Overrun error (OE) detection Notes 1: As the transmit interrupt (TI), either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O control register. 2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TxD pin. 3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” . Fig. 15 Operation of clock synchronous serial I/O function 16 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (2) Asynchronous Serial I/O (UART) Mode two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive buffer register can hold a character while the next character is being received. Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O mode selection bit (b6) of the serial I/O control register to “0”. Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift registers each have a buffer, but the Data bus Address 0018 16 Serial I/O control register P24/RXD Address 001A 16 Receive buffer full flag (RBF) Receive interrupt request (RI) Receive buffer register OE Character length selection bit ST detector 7 bits Receive shift register 1/16 8 bits PE FE SP detector Clock control circuit UART control register Address 001B 16 Serial I/O synchronous clock selection bit P26/SCLK1 XIN BRG count source selection bit Frequency division ratio 1/(n+1) Baud rate generator Address 001C 16 1/4 ST/SP/PA generator 1/16 P25/TXD Transmit shift register Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Character length selection bit Transmit buffer register Address 001816 Transmit buffer empty flag (TBE) Serial I/O status register Address 001916 Data bus Fig.16 Block diagram of UART serial I/O 17 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Transmit or receive clock Transmit buffer write signal TBE=0 TSC=0 TBE=1 Serial output TXD TBE=0 TBE=1 ST D0 D1 SP TSC=1 ST D0 D1 1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit (s) Receive buffer read signal SP Generated at 2nd bit in 2-stop-bit mode RBF=0 RBF=1 Serial input RXD ST D0 D1 SP RBF=1 ST D0 D1 SP Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception). 2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit interrupt source selection bit (TIC) of the serial I/O control register. 3: The receive interrupt (RI) is set when the RBF flag becomes “1.” 4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0. Fig. 17 Operation of UART serial I/O function [Transmit Buffer Register/Receive Buffer Register (TB/RB)] 001816 The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is “0”. [Serial I/O Status Register (SIOSTS)] 001916 The read-only serial I/O status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to “0” when the receive buffer register is read. If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O status register clears all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively). Writing “0” to the serial I/O enable bit SIOE (bit 7 of the serial I/O control register) also clears all the status flags, including the error flags. Bits 0 to 6 of the serial I/O status register are initialized to “0” at reset, but if the transmit enable bit (bit 4) of the serial I/O control register has been set to “1”, the transmit shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become “1”. 18 Serial I/O Control Register (SIOCON)] 001A16 The serial I/O control register consists of eight control bits for the serial I/O function. [UART Control Register (UARTCON)] 001B16 The UART control register consists of four control bits (bits 0 to 3) which are valid when asynchronous serial I/O is selected and set the data format of an data transfer and one bit (bit 4) which is always valid and sets the output structure of the P2 5/T XD pin. [Baud Rate Generator (BRG)] 001C16 The baud rate generator determines the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator. ■Note When using the serial I/O, clear the I2 C-BUS interface enable bit to “0” or the SCL/SDA interrupt pin selection bit to “0”. MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 Serial I/O status register (SIOSTS : address 0019 16) Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns “1” when read) b7 b0 UART control register (UARTCON : address 001B 16) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits b7 b0 Serial I/O control register (SIOCON : address 001A 16) BRG count source selection bit (CSS) 0: f(X IN) 1: f(X IN)/4 Serial I/O synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O is selected, BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O is selected, external clock input divided by 16 when UART is selected. SRDY output enable bit (SRDY) 0: P2 7 pin operates as ordinary I/O pin 1: P2 7 pin operates as S RDY output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O mode selection bit (SIOM) 0: Clock asynchronous (UART) serial I/O 1: Clock synchronous serial I/O Serial I/O enable bit (SIOE) 0: Serial I/O disabled (pins P2 4 to P2 7 operate as ordinary I/O pins) 1: Serial I/O enabled (pins P2 4 to P2 7 operate as serial I/O pins) Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits P25/TXD P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) Not used (return “1” when read) Fig. 18 Structure of serial I/O control registers 19 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MULTI-MASTER I2C-BUS INTERFACE Table 4 Multi-master I2 C-BUS interface functions I 2C-BUS The multi-master interface is a serial communications circuit, conforming to the Philips I2 C-BUS data transfer format. This interface, offering both arbitration lost detection and a synchronous functions, is useful for the multi-master serial communications. Figure 19 shows a block diagram of the multi-master I2C-BUS interface and Table 4 lists the multi-master I 2C-BUS interface functions. This multi-master I2 C-BUS interface consists of the I 2C address register, the I2C data shift register, the I2C clock control register, the I2 C control register, the I2C status register, the I2 C start/stop condition control register and other control circuits. When using the multi-master I 2C-BUS interface, set 1 MHz or more to φ. Item Format Communication mode SCL clock frequency Function In conformity with Philips I2 C-BUS standard: 10-bit addressing format 7-bit addressing format High-speed clock mode Standard clock mode In conformity with Philips I2 C-BUS standard: Master transmission Master reception Slave transmission Slave reception 16.1 kHz to 400 kHz (at φ= 4 MHz) System clock φ = f(X IN)/2 (high-speed mode) φ = f(XIN)/8 (middle-speed mode) Note: Mitsubishi Electric Corporation assumes no responsibility for infringement of any third-party’s rights or originating in the use of the connection control function between the I 2C-BUS interface and the ports SCL 1, SCL2 , SDA1 and SDA2 with the bit 6 of I2C control register (002E 16). b7 I2C address register b0 Interrupt generating circuit SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW S0D Interrupt request signal (IICIRQ) Address comparator Serial data (SDA) Noise elimination circuit Data control circuit b0 b7 I2C data shift register b7 b0 S0 MST TRX BB PIN SIS SIP SSC4 SSC3 SSC2 SSC1 SSC0 S2D AL circuit A L AAS AD0 LRB I2C status register S1 I2C start/stop condition control register Internal data bus BB circuit Serial clock (SCL) Noise elimination circuit Clock control circuit b7 ACK b0 ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE S2 I2C clock control register Clock division I2C clock control register S1D b0 b7 TISS CLK STP 10BIT SAD ALS S1D I2 C control register System clock (φ) ES0 BC2 BC1 BC0 Bit counter Fig. 19 Block diagram of multi-master I2C-BUS interface ✽ : Purchase of MITSUBISHI ELECTRIC CORPORATIONS I2 C components conveys a license under the Philips I 2C Patent Rights to use these components an I2 C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. 20 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [I2C Data Shift Register (S0)] 002B16 The I2 C data shift register (S0 : address 002B16 ) is an 8-bit shift register to store receive data and write transmit data. When transmit data is written into this register, it is transferred to the outside from bit 7 in synchronization with the SCL clock, and each time one-bit data is output, the data of this register are shifted by one bit to the left. When data is received, it is input to this register from bit 0 in synchronization with the SCL clock, and each time one-bit data is input, the data of this register are shifted by one bit to the left. The minimum 2 machine cycles are required from the rising of the SCL clock until input to this register. The I2C data shift register is in a write enable status only when the I 2C-BUS interface enable bit (ES0 bit : bit 3 of address 002E16 ) of the I2C control register is “1”. The bit counter is reset by a write instruction to the I 2C data shift register. When both the ES0 bit and the MST bit of the I2C status register (address 002D16) are “1,” the SCL is output by a write instruction to the I2 C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ES0 bit value. b7 b0 SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RWB I2C address register (S0D: address 002C 16) Read/write bit Slave address Fig. 20 Structure of I2C address register [I2C Address Register (S0D)] 002C16 The I2 C address register (address 002C 16) consists of a 7-bit slave address and a read/write bit. In the addressing mode, the slave address written in this register is compared with the address data to be received immediately after the START condition is detected. •Bit 0: Read/write bit (RWB) This is not used in the 7-bit addressing mode. In the 10-bit addressing mode, the first address data to be received is compared with the contents (SAD6 to SAD0 + RBW) of the I2 C address register. The RBW bit is cleared to “0” automatically when the stop condition is detected. •Bits 1 to 7: Slave address (SAD0–SAD6) These bits store slave addresses. Regardless of the 7-bit address 21 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER I2 C Note: Do not write data into the clock control register during transfer. If data is written during transfer, the I 2 C clock generator is reset, so that data cannot be transferred normally. 22 I2C clock control register (S2 : address 002F 16) SCL frequency control bits Refer to Table 5. SCL mode specification bit 0 : Standard clock mode 1 : High-speed clock mode ACK bit 0 : ACK is returned. 1 : ACK is not returned. ACK clock bit 0 : No ACK clock 1 : ACK clock Fig. 21 Structure of I2C clock control register Table 5 Set values of I 2C clock control register and SCL frequency Setting value of CCR4–CCR0 SCL frequency (at φ = 4 MHz, unit : kHz) Standard clock High-speed clock CCR4 CCR3 CCR2 CCR1 CCR0 mode mode Setting disabled Setting disabled 0 0 0 0 0 Setting disabled Setting disabled 0 0 0 0 1 Setting disabled Setting disabled 0 0 0 1 0 0 0 1 1 – (Note 2) 333 0 0 1 0 0 – (Note 2) 250 0 0 1 0 1 100 400 (Note 3) 0 0 1 1 0 83.3 166 … 0 … •Bit 7: ACK clock bit (ACK) This bit specifies the mode of acknowledgment which is an acknowledgment response of data transfer. When this bit is set to “0,” the no ACK clock mode is selected. In this case, no ACK clock occurs after data transmission. When the bit is set to “1,” the ACK clock mode is selected and the master generates an ACK clock each completion of each 1-byte data transfer. The device for transmitting address data and control data releases the SDA at the occurrence of an ACK clock (makes SDA “H”) and receives the ACK bit generated by the data receiving device. b0 ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE … ✽ACK clock: Clock for acknowledgment b7 ACK … The I2C clock control register (address 002F16 ) is used to set ACK control, SCL mode and SCL frequency. •Bits 0 to 4: SCL frequency control bits (CCR0–CCR4) These bits control the SCL frequency. Refer to Table 5. •Bit 5: SCL mode specification bit (FAST MODE) This bit specifies the SCL mode. When this bit is set to “0,” the standard clock mode is selected. When the bit is set to “1,” the high-speed clock mode is selected. When connecting the bus of the high-speed mode I 2C bus standard (maximum 400 kbits/s), use 8 MHz or more oscillation frequency f(XIN) and 2 division clock. •Bit 6: ACK bit (ACK BIT) This bit sets the SDA status when an ACK clock✽ is generated. When this bit is set to “0,” the ACK return mode is selected and SDA goes to “L” at the occurrence of an ACK clock. When the bit is set to “1,” the ACK non-return mode is selected. The SDA is held in the “H” status at the occurrence of an ACK clock. However, when the slave address agree with the address data in the reception of address data at ACK BIT = “0,” the SDA is automatically made “L” (ACK is returned). If there is a disagreement between the slave address and the address data, the SDA is automatically made “H” (ACK is not returned). … [I2C Clock Control Register (S2)] 002F16 500/CCR value (Note 3) 1 1 1 0 1 17.2 1000/CCR value (Note 3) 34.5 1 1 1 1 0 16.6 33.3 1 1 1 1 1 16.1 32.3 Notes 1: Duty of SCL clock output is 50 %. The duty becomes 35 to 45 % only when the high-speed clock mode is selected and CCR value = 5 (400 kHz, at φ = 4 MHz). “H” duration of the clock fluctuates from –4 to +2 machine cycles in the standard clock mode, and fluctuates from –2 to +2 machine cycles in the high-speed clock mode. In the case of negative fluctuation, the frequency does not increase because “L” duration is extended instead of “H” duration reduction. These are value when S CL clock synchronization by the synchronous function is not performed. CCR value is the decimal notation value of the SCL frequency control bits CCR4 to CCR0. 2: Each value of S CL frequency exceeds the limit at φ = 4 MHz or more. When using these setting value, use φ of 4 MHz or less. 3: The data formula of SCL frequency is described below: φ/(8 ✕ CCR value) Standard clock mode φ/(4 ✕ CCR value) High-speed clock mode (CCR value ≠ 5) φ/(2 ✕ CCR value) High-speed clock mode (CCR value = 5) Do not set 0 to 2 as CCR value regardless of φ frequency. Set 100 kHz (max.) in the standard clock mode and 400 kHz (max.) in the high-speed clock mode to the SCL frequency by setting the SCL frequency control bits CCR4 to CCR0. MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [I2C Control Register (S1D)] 002E16 The I2 C control register (address 002E16 ) controls data communication format. •Bits 0 to 2: Bit counter (BC0–BC2) These bits decide the number of bits for the next 1-byte data to be transmitted. The I2 C interrupt request signal occurs immediately after the number of count specified with these bits (ACK clock is added to the number of count when ACK clock is selected by ACK clock bit (bit 7 of address 002F 16)) have been transferred, and BC0 to BC2 are returned to “0002 ”. Also when a START condition is received, these bits become “0002” and the address data is always transmitted and received in 8 bits. •Bit 3: I2C interface enable bit (ES0) This bit enables to use the multi-master I2C-BUS interface. When this bit is set to “0,” the use disable status is provided, so that the SDA and the SCL become high-impedance. When the bit is set to “1,” use of the interface is enabled. When ES0 = “0,” the following is performed. • PIN = “1,” BB = “0” and AL = “0” are set (which are bits of the I2 C status register at address 002D16 ). • Writing data to the I2C data shift register (address 002B16 ) is disabled. •Bit 4: Data format selection bit (ALS) This bit decides whether or not to recognize slave addresses. When this bit is set to “0,” the addressing format is selected, so that address data is recognized. When a match is found between a slave address and address data as a result of comparison or when a general call (refer to “I 2C Status Register,” bit 1) is received, transfer processing can be performed. When this bit is set to “1,” the free data format is selected, so that slave addresses are not recognized. •Bit 5: Addressing format selection bit (10BIT SAD) This bit selects a slave address specification format. When this bit is set to “0,” the 7-bit addressing format is selected. In this case, only the high-order 7 bits (slave address) of the I2C address register (address 002C16 ) are compared with address data. When this bit is set to “1,” the 10-bit addressing format is selected, and all the bits of the I2 C address register are compared with address data. •Bit 6: SDA/SCL pin selection bit This bit selects the input/output pins of SCL and SDA of the multimaster I2C-BUS interface. •Bit 7: I2C-BUS interface pin input level selection bit This bit selects the input level of the SCL and SDA pins of the multi-master I2C-BUS interface. TSEL SCL1/P23 SCL SCL2/TxD/P25 Multi-master I2C-BUS interface TSEL TSEL SDA1/P22 SDA SDA2/RxD/P24 TSEL Fig. 22 SDA/SCL pin selection bit b7 TISS TSEL b0 10 BIT SAD I2C control register ALS ES0 BC2 BC1 BC0 (S1D : address 002E 16) Bit counter (Number of transmit/receive bits) b2 b1 b0 0 0 0 : 8 0 0 1 : 7 0 1 0 : 6 0 1 1 : 5 1 0 0 : 4 1 0 1 : 3 1 1 0 : 2 1 1 1 : 1 I2C-BUS interface enable bit 0 : Disabled 1 : Enabled Data format selection bit 0 : Addressing format 1 : Free data format Addressing format selection bit 0 : 7-bit addressing format 1 : 10-bit addressing format SDA/SCL pin selection bit 0 : Connect to ports P2 2, P23 1 : Connect to ports P2 4, P25 I2C-BUS interface pin input level selection bit 0 : CMOS input 1 : SMBUS input Fig. 23 Structure of I2C control register 23 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [I2C Status Register (S1)] 002D16 The I2 C status register (address 002D16 ) controls the I2 C-BUS interface status. The low-order 4 bits are read-only bits and the high-order 4 bits can be read out and written to. Set “00002 ” to the low-order 4 bits, because these bits become the reserved bits at writing. •Bit 0: Last receive bit (LRB) This bit stores the last bit value of received data and can also be used for ACK receive confirmation. If ACK is returned when an ACK clock occurs, the LRB bit is set to “0.” If ACK is not returned, this bit is set to “1.” Except in the ACK mode, the last bit value of received data is input. The state of this bit is changed from “1” to “0” by executing a write instruction to the I2C data shift register (address 002B16 ). •Bit 1: General call detecting flag (AD0) When the ALS bit is “0”, this bit is set to “1” when a general call ✽ whose address data is all “0” is received in the slave mode. By a general call of the master device, every slave device receives control data after the general call. The AD0 bit is set to “0” by detecting the STOP condition or START condition, or reset. ✽General call: The master transmits the general call address “0016” to all slaves. •Bit 2: Slave address comparison flag (AAS) This flag indicates a comparison result of address data when the ALS bit is “0”. ➀ In the slave receive mode, when the 7-bit addressing format is selected, this bit is set to “1” in one of the following conditions: • The address data immediately after occurrence of a START condition agrees with the slave address stored in the high-order 7 bits of the I2 C address register (address 002C16). • A general call is received. ➁ In the slave receive mode, when the 10-bit addressing format is selected, this bit is set to “1” with the following condition: • When the address data is compared with the I2C address register (8 bits consisting of slave address and RBW bit), the first bytes agree. ➂ This bit is set to “0” by executing a write instruction to the I2 C data shift register (address 002B 16 ) when ES0 is set to “1” or reset. •Bit 3: Arbitration lost✽ detecting flag (AL) In the master transmission mode, when the SDA is made “L” by any other device, arbitration is judged to have been lost, so that this bit is set to “1.” At the same time, the TRX bit is set to “0,” so that immediately after transmission of the byte whose arbitration was lost is completed, the MST bit is set to “0.” The arbitration lost can be detected only in the master transmission mode. When arbitration is lost during slave address transmission, the TRX bit is set to “0” and the reception mode is set. Consequently, it becomes possible to detect the agreement of its own slave address and address data transmitted by another master device. ✽Arbitration lost :The status in which communication as a master is disabled. 24 •Bit 4: SCL pin low hold bit (PIN) This bit generates an interrupt request signal. Each time 1-byte data is transmitted, the PIN bit changes from “1” to “0.” At the same time, an interrupt request signal occurs to the CPU. The PIN bit is set to “0” in synchronization with a falling of the last clock (including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling of the PIN bit. When the PIN bit is “0,” the SCL is kept in the “0” state and clock generation is disabled. Figure 25 shows an interrupt request signal generating timing chart. The PIN bit is set to “1” in one of the following conditions: • Executing a write instruction to the I 2C data shift register (address 002B16 ). (This is the only condition which the prohibition of the internal clock is released and data can be communicated except for the start condition detection.) • When the ES0 bit is “0” • At reset • When writing “1” to the PIN bit by software The conditions in which the PIN bit is set to “0” are shown below: • Immediately after completion of 1-byte data transmission (including when arbitration lost is detected) • Immediately after completion of 1-byte data reception • In the slave reception mode, with ALS = “0” and immediately after completion of slave address agreement or general call address reception • In the slave reception mode, with ALS = “1” and immediately after completion of address data reception •Bit 5: Bus busy flag (BB) This bit indicates the status of use of the bus system. When this bit is set to “0,” this bus system is not busy and a START condition can be generated. The BB flag is set/reset by the SCL, SDA pins input signal regardless of master/slave. This flag is set to “1” by detecting the start condition, and is set to “0” by detecting the stop condition. The condition of these detecting is set by the start/stop condition setting bits (SSC4–SSC0) of the I2 C start/stop condition control register (address 003016). When the ES0 bit of the I2C control register (address 002E16 ) is “0” or reset, the BB flag is set to “0.” For the writing function to the BB flag, refer to the sections “START Condition Generating Method” and “STOP Condition Generating Method” described later. MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER •Bit 6: Communication mode specification bit (transfer direction specification bit: TRX) This bit decides a direction of transfer for data communication. When this bit is “0,” the reception mode is selected and the data of a transmitting device is received. When the bit is “1,” the transmission mode is selected and address data and control data are output onto the SDA in synchronization with the clock generated on the SCL . This bit is set/reset by software and hardware. About set/reset by hardware is described below. This bit is set to “1” by hardware when all the following conditions are satisfied: • When ALS is “0” • In the slave reception mode or the slave transmission mode • When the R/W bit reception is “1” This bit is set to “0” in one of the following conditions: • When arbitration lost is detected. • When a STOP condition is detected. • When writing “1” to this bit by software is invalid by the START condition duplication preventing function (Note). • With MST = “0” and when a START condition is detected. • With MST = “0” and when ACK non-return is detected. • At reset •Bit 7: Communication mode specification bit (master/slave specification bit: MST) This bit is used for master/slave specification for data communication. When this bit is “0,” the slave is specified, so that a START condition and a STOP condition generated by the master are received, and data communication is performed in synchronization with the clock generated by the master. When this bit is “1,” the master is specified and a START condition and a STOP condition are generated. Additionally, the clocks required for data communication are generated on the SCL. This bit is set to “0” in one of the following conditions. • Immediately after completion of 1-byte data transfer when arbitration lost is detected • When a STOP condition is detected. • Writing “1” to this bit by software is invalid by the START condition duplication preventing function (Note). • At reset Note: START condition duplication preventing function The MST, TRX, and BB bits is set to “1” at the same time after confirming that the BB flag is “0” in the procedure of a START condition occurrence. However, when a START condition by another master device occurs and the BB flag is set to “1” immediately after the contents of the BB flag is confirmed, the START condition duplication preventing function makes the writing to the MST and TRX bits invalid. The duplication preventing function becomes valid from the rising of the BB flag to reception completion of slave address. b7 b0 MST TRX BB PIN AL AAS AD0 LRB I2C status register (S1 : address 002D 16) Last receive bit (Note) 0 : Last bit = “0” 1 : Last bit = “1” General call detecting flag (Note) 0 : No general call detected 1 : General call detected Slave address comparison flag (Note) 0 : Address disagreement 1 : Address agreement Arbitration lost detecting flag (Note) 0 : Not detected 1 : Detected SCL pin low hold bit 0 : SCL pin low hold 1 : SCL pin low release Bus busy flag 0 : Bus free 1 : Bus busy Communication mode specification bits 00 : Slave receive mode 01 : Slave transmit mode 10 : Master receive mode 11 : Master transmit mode Note: These bits and flags can be read out, but cannot be written. Write “0” to these bits at writing. Fig. 24 Structure of I2C status register SCL PIN IICIRQ Fig. 25 Interrupt request signal generating timing 25 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER START Condition Generating Method START/STOP Condition Detecting Operation When writing “1” to the MST, TRX, and BB bits of the I 2C status register (address 002D 16) at the same time after writing the slave address to the I2C data shift register (address 002B16) with the condition in which the ES0 bit of the I2 C control register (address 002E16 ) and the BB flag are “0”, a START condition occurs. After that, the bit counter becomes “0002 ” and an SCL for 1 byte is output. The START condition generating timing is different in the standard clock mode and the high-speed clock mode. Refer to Figure 26, the START condition generating timing diagram, and Table 6, the START condition generating timing table. The START/STOP condition detection operations are shown in Figures 28, 29, and Table 8. The START/STOP condition is set by the START/STOP condition set bit. The START/STOP condition can be detected only when the input signal of the SCL and SDA pins satisfy three conditions: S CL release time, setup time, and hold time (see Table 8). The BB flag is set to “1” by detecting the START condition and is reset to “0” by detecting the STOP condition. The BB flag set/reset timing is different in the standard clock mode and the high-speed clock mode. Refer to Table 8, the BB flag set/ reset time. Note: When a STOP condition is detected in the slave mode (MST = 0), an interrupt request signal “IICIRQ” occurs to the CPU. I2C status register write signal SCL SDA Setup time SCL release time Hold time SCL SDA Fig. 26 START condition generating timing diagram Table 6 START condition generating timing table Item Standard clock mode High-speed clock mode Setup time 5.0 µs (20 cycles) 2.5 µs (10 cycles) Hold time 5.0 µs (20 cycles) 2.5 µs (10 cycles) Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the number of φ cycles. STOP Condition Generating Method When the ES0 bit of the I 2C control register (address 002E 16) is “1,” write “1” to the MST and TRX bits, and write “0” to the BB bit of the I2C status register (address 002D16 ) simultaneously. Then a STOP condition occurs. The STOP condition generating timing is different in the standard clock mode and the high-speed clock mode. Refer to Figure 27, the STOP condition generating timing diagram, and Table 7, the STOP condition generating timing table. SCL Fig. 28 START/STOP condition detecting timing diagram SCL release time SCL SDA BB flag SDA Hold time Fig. 27 STOP condition generating timing diagram Table 7 STOP condition generating timing table Standard clock mode High-speed clock mode Item 5.0 µs (20 cycles) 3.0 µs (12 cycles) Setup time 4.5 µs (18 cycles) 2.5 µs (10 cycles) Hold time Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the number of φ cycles. 26 Setup time Hold time BB flag reset time Fig. 29 STOP condition detecting timing diagram Table 8 START condition/STOP condition detecting conditions Standard clock mode High-speed clock mode SCL release time SCC value + 1 cycle (6.25 µs) 4 cycles (1.0 µs) Setup time BB flag set/ reset time Setup time Hold time BB flag reset time BB flag Hold time I2C status register write signal Setup time SCC value + 1 cycle < 4.0 µs (3.125 µs) 2 cycles (1.0 µs) 2 SCC value + 1 cycle < 4.0 µs (3.125 µs) 2 cycles (0.5 µs) 2 SCC value –1 + 2 cycles (3.375 µs) 3.5 cycles (0.875 µs) 2 Note: Unit : Cycle number of system clock φ SSC value is the decimal notation value of the START/STOP condition set bits SSC4 to SSC0. Do not set “0” or an odd number to SSC value. The value in parentheses is an example when the I2C START/ STOP condition control register is set to “1816” at φ = 4 MHz. MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [I2C START/STOP Condition Control Register (S2D)] 003016 The I 2C START/STOP condition control register (address 003016 ) controls START/STOP condition detection. •Bits 0 to 4: START/STOP condition set bit (SSC4–SSC0) SCL release time, setup time, and hold time change the detection condition by value of the main clock divide ratio selection bit and the oscillation frequency f(XIN ) because these time are measured by the internal system clock. Accordingly, set the proper value to the START/STOP condition set bits (SSC4 to SSC0) in considered of the system clock frequency. Refer to Table 8. Do not set “000002” or an odd number to the START/STOP condition set bit (SSC4 to SSC0). Refer to Table 9, the recommended set value to START/STOP condition set bits (SSC4–SSC0) for each oscillation frequency. •Bit 5: SCL/SDA interrupt pin polarity selection bit (SIP) An interrupt can occur when detecting the falling or rising edge of the SCL or SDA pin. This bit selects the polarity of the SCL or SDA pin interrupt pin. •Bit 6: SCL/SDA interrupt pin selection bit (SIS) This bit selects the pin of which interrupt becomes valid between the SCL pin and the SDA pin. Note: When changing the setting of the SCL /S DA interrupt pin polarity selection bit, the S CL/SDA interrupt pin selection bit, or the I 2 C-BUS interface enable bit ES0, the S CL/SDA interrupt request bit may be set. When selecting the SCL /S DA interrupt source, disable the interrupt before the S CL /S DA interrupt pin polarity selection bit, the S CL/ S DA interrupt pin selection bit, or the I2 C-BUS interface enable bit ES0 is set. Reset the request bit to “0” after setting these bits, and enable the interrupt. Address Data Communication There are two address data communication formats, namely, 7-bit addressing format and 10-bit addressing format. The respective address communication formats are described below. ➀ 7-bit addressing format To adapt the 7-bit addressing format, set the 10BIT SAD bit of the I2 C control register (address 002E16 ) to “0.” The first 7-bit address data transmitted from the master is compared with the high-order 7-bit slave address stored in the I2C address register (address 002C16). At the time of this comparison, address comparison of the RWB bit of the I 2C address register (address 002C16) is not performed. For the data transmission format when the 7-bit addressing format is selected, refer to Figure 31, (1) and (2). ➁ 10-bit addressing format To adapt the 10-bit addressing format, set the 10BIT SAD bit of the I 2C control register (address 002E 16) to “1.” An address comparison is performed between the first-byte address data transmitted from the master and the 8-bit slave address stored in the I2C address register (address 002C16 ). At the time of this comparison, an address comparison between the RWB bit of the I 2 C address register (address 002C16 ) and the R/W bit which is the last bit of the address data transmitted from the master is made. In the 10-bit addressing mode, the RWB bit which is the last bit of the address data not only specifies the direction of communication for control data, but also is processed as an address data bit. When the first-byte address data agree with the slave address, the AAS bit of the I2C status register (address 002D16 ) is set to “1.” After the second-byte address data is stored into the I2C data shift register (address 002B 16 ), perform an address comparison between the second-byte data and the slave address by software. When the address data of the 2 bytes agree with the slave address, set the RBW bit of the I2 C address register (address 002C 16) to “1” by software. This processing can make the 7-bit slave address and R/W data agree, which are received after a RESTART condition is detected, with the value of the I 2C address register (address 002C16 ). For the data transmission format when the 10-bit addressing format is selected, refer to Figure 31, (3) and (4). 27 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 SIS SIP I2C START/STOP condition control register (S2D : address 0030 16) SSC4 SSC3 SSC2 SSC1 SSC0 START/STOP condition set bit SCL/SDA interrupt pin polarity selection bit 0 : Falling edge active 1 : Rising edge active SCL/SDA interrupt pin selection bit 0 : SDA valid 1 : SCL valid Reserved Do not write “1” to this bit. Fig. 30 Structure of I2C START/STOP condition control register Table 9 Recommended set value to START/STOP condition set bits (SSC4–SSC0) for each oscillation frequency Oscillation frequency f(XIN) (MHz) Main clock divide ratio System clock φ (MHz) 8 2 4 8 8 1 4 2 2 2 2 1 START/STOP condition control register SCL release time (µs) Setup time (µs) Hold time (µs) XXX11010 XXX11000 XXX00100 XXX01100 XXX01010 XXX00100 6.75 µs (27 cycles) 6.25 µs (25 cycles) 5.0 µs (5 cycles) 6.5 µs (13 cycles) 5.5 µs (11 cycles) 5.0 µs (5 cycles) 3.375 µs (13.5 cycles) 3.125 µs (12.5 cycles) 2.5 µs (2.5 cycles) 3.25 µs (6.5 cycles) 2.75 µs (5.5 cycles) 2.5 µs (2.5 cycles) 3.375 µs (13.5 cycles) 3.125 µs (12.5 cycles) 2.5 µs (2.5 cycles) 3.25 µs (6.5 cycles) 2.75 µs (5.5 cycles) 2.5 µs (2.5 cycles) Note: Do not set an odd number to the START/STOP condition set bit (SSC4 to SSC0). S Slave address R/W 7 bits A “0” Data A 1 to 8 bits Data A/A P A P 1 to 8 bits (1) A master-transmitter transnmits data to a slave-receiver S Slave address R/W 7 bits A “1” Data A 1 to 8 bits Data 1 to 8 bits (2) A master-receiver receives data from a slave-transmitter S Slave address R/W 1st 7 bits 7 bits A “0” Slave address 2nd bytes A Data 1 to 8 bits 8 bits A Data A/A P 1 to 8 bits (3) A master-transmitter transmits data to a slave-receiver with a 10-bit address S Slave address R/W 1st 7 bits A Slave address 2nd bytes A Sr Slave address R/W 1st 7 bits “1” 7 bits “0” 8 bits 7 bits (4) A master-receiver receives data from a slave-transmitter with a 10-bit address S : START condition A : ACK bit Sr : Restart condition P : STOP condition R/W : Read/Write bit Fig. 31 Address data communication format 28 : Master to slave : Slave to master A Data 1 to 8 bits A Data 1 to 8 bits A P MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Example of Master Transmission An example of master transmission in the standard clock mode, at the SCL frequency of 100 kHz and in the ACK return mode is shown below. ➀ Set a slave address in the high-order 7 bits of the I2C address register (address 002C16 ) and “0” into the RWB bit. ➁ Set the ACK return mode and SCL = 100 kHz by setting “8516 ” in the I2 C clock control register (address 002F16 ). ➂ Set “0016” in the I2 C status register (address 002D16) so that transmission/reception mode can become initializing condition. ➃ Set a communication enable status by setting “0816 ” in the I2C control register (address 002E16 ). ➄ Confirm the bus free condition by the BB flag of the I2 C status register (address 002D16 ). ➅ Set the address data of the destination of transmission in the high-order 7 bits of the I 2C data shift register (address 002B16) and set “0” in the least significant bit. ➆ Set “F016 ” in the I2C status register (address 002D16 ) to generate a START condition. At this time, an SCL for 1 byte and an ACK clock automatically occur. ➇ Set transmit data in the I2C data shift register (address 002B 16 ). At this time, an SCL and an ACK clock automatically occur. ➈ When transmitting control data of more than 1 byte, repeat step ➇. ➉ Set “D016” in the I 2C status register (address 002D16 ) to generate a STOP condition if ACK is not returned from slave reception side or transmission ends. Example of Slave Reception An example of slave reception in the high-speed clock mode, at the SCL frequency of 400 kHz, in the ACK non-return mode and using the addressing format is shown below. ➀ Set a slave address in the high-order 7 bits of the I2C address register (address 002C16 ) and “0” in the RWB bit. ➁ Set the no ACK clock mode and SCL = 400 kHz by setting “6516 ” in the I2 C clock control register (address 002F16 ). ➂ Set “0016” in the I2 C status register (address 002D16) so that transmission/reception mode can become initializing condition. ➃ Set a communication enable status by setting “0816 ” in the I2C control register (address 002E16 ). ➄ When a START condition is received, an address comparison is performed. ➅ •When all transmitted addresses are “0” (general call): AD0 of the I2 C status register (address 002D16) is set to “1” and an interrupt request signal occurs. • When the transmitted addresses agree with the address set in ➀: ASS of the I2C status register (address 002D16) is set to “1” and an interrupt request signal occurs. • In the cases other than the above AD0 and AAS of the I2C status register (address 002D16) are set to “0” and no interrupt request signal occurs. ➆ Set dummy data in the I2C data shift register (address 002B16 ). ➇ When receiving control data of more than 1 byte, repeat step ➆. ➈ When a STOP condition is detected, the communication ends. 29 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ■Precautions when using multi-master I2 C-BUS interface (1) Read-modify-write instruction The precautions when the read-modify-write instruction such as SEB, CLB etc. is executed for each register of the multi-master I 2C-BUS interface are described below. • I 2C data shift register (S0: address 002B16 ) When executing the read-modify-write instruction for this register during transfer, data may become a value not intended. • I 2C address register (S0D: address 002C16 ) When the read-modify-write instruction is executed for this register at detecting the STOP condition, data may become a value not intended. It is because H/W changes the read/write bit (RBW) at the above timing. • I 2C status register (S1: address 002D16 ) Do not execute the read-modify-write instruction for this register because all bits of this register are changed by H/W. • I 2C control register (S1D: address 002E16 ) When the read-modify-write instruction is executed for this register at detecting the START condition or at completing the byte transfer, data may become a value not intended. Because H/W changes the bit counter (BC0-BC2) at the above timing. • I 2C clock control register (S2: address 002F 16) The read-modify-write instruction can be executed for this register. • I 2 C START/STOP condition control register (S2D: address 0030 16) The read-modify-write instruction can be executed for this register. (2) START condition generating procedure using multi-master 1. Procedure example (The necessary conditions of the generating procedure are described as the following 2 to 5. :: LDA — (Taking out of slave address value) SEI (Interrupt disabled) BBS 5, S1, BUSBUSY (BB flag confirming and branch process) BUSFREE: STA S0 (Writing of slave address value) LDM #$F0, S1 (Trigger of START condition generating) CLI (Interrupt enabled) :: BUSBUSY: CLI (Interrupt enabled) :: 2. Use “Branch on Bit Set” of “BBS 5, $002D, –” for the BB flag confirming and branch process. 3. Use “STA $2B, STX $2B” or “STY $2B” of the zero page addressing instruction for writing the slave address value to the I2 C data shift register. 4. Execute the branch instruction of above 2 and the store instruction of above 3 continuously shown the above procedure example. 30 5. Disable interrupts during the following three process steps: • BB flag confirming • Writing of slave address value • Trigger of START condition generating When the condition of the BB flag is bus busy, enable interrupts immediately. (3) RESTART condition generating procedure 1. Procedure example (The necessary conditions of the generating procedure are described as the following 2 to 4.) Execute the following procedure when the PIN bit is “0.” :: LDM #$00, S1 (Select slave receive mode) LDA — (Taking out of slave address value) SEI (Interrupt disabled) STA S0 (Writing of slave address value) LDM #$F0, S1 (Trigger of RESTART condition generating) CLI (Interrupt enabled) :: 2. Select the slave receive mode when the PIN bit is “0.” Do not write “1” to the PIN bit. Neither “0” nor “1” is specified for the writing to the BB bit. The TRX bit becomes “0” and the SDA pin is released. 3. The SCL pin is released by writing the slave address value to the I2 C data shift register. 4. Disable interrupts during the following two process steps: • Writing of slave address value • Trigger of RESTART condition generating (4) Writing to I 2C status register Do not execute an instruction to set the PIN bit to “1” from “0” and an instruction to set the MST and TRX bits to “0” from “1” simultaneously. It is because it may enter the state that the SCL pin is released and the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to “0” from “1” simultaneously when the PIN bit is “1.” It is because it may become the same as above. (5) Process of after STOP condition generating Do not write data in the I2C data shift register S0 and the I2C status register S1 until the bus busy flag BB becomes “0” after generating the STOP condition in the master mode. It is because the STOP condition waveform might not be normally generated. Reading to the above registers do not have the problem. MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PULSE WIDTH MODULATION (PWM) PWM Operation The 3851 group has a PWM function with an 8-bit resolution, based on a signal that is the clock input XIN or that clock input divided by 2. When bit 0 (PWM enable bit) of the PWM control register is set to “1”, operation starts by initializing the PWM output circuit, and pulses are output starting at an “H”. If the PWM register or PWM prescaler is updated during PWM output, the pulses will change in the cycle after the one in which the change was made. Data Setting The PWM output pin also functions as port P4 4. Set the PWM period by the PWM prescaler, and set the “H” term of output pulse by the PWM register. If the value in the PWM prescaler is n and the value in the PWM register is m (where n = 0 to 255 and m = 0 to 255) : PWM period = 255 ✕ (n+1) / f(XIN) = 31.875 ✕ (n+1) µs (when f(X IN) = 8 MHz) Output pulse “H” term = PWM period ✕ m / 255 = 0.125 ✕ (n+1) ✕ m µs (when f(XIN) = 8 MHz) 31.875 ✕ m ✕ (n+1) µs 255 PWM output T = [31.875 ✕ (n+1)] µs m: Contents of PWM register n : Contents of PWM prescaler T : PWM period (when f(X IN) = 8 MHz) Fig. 32 Timing of PWM period Data bus PWM prescaler pre-latch PWM register pre-latch Transfer control circuit PWM prescaler latch PWM register latch PWM prescaler PWM register Count source selection bit “0” XIN 1/2 Port P44 “1” Port P44 latch PWM enable bit Fig. 33 Block diagram of PWM function 31 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 PWM control register (PWMCON : address 001D 16) PWM function enable bit 0: PWM disabled 1: PWM enabled Count source selection bit 0: f(XIN) 1: f(XIN)/2 Not used (return “0” when read) Fig. 34 Structure of PWM control register A B B = C T2 T C PWM output T PWM register write signal PWM prescaler write signal T T2 (Changes “H” term from “A” to “B”.) (Changes PWM period from “T” to “T2”.) When the contents of the PWM register or PWM prescaler have changed, the PWM output will change from the next period after the change. Fig. 35 PWM output timing when PWM register or PWM prescaler is changed 32 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER A-D CONVERTER [A-D Conversion Registers (ADL, ADH)] 003516, 003616 b7 b0 AD control register (ADCON : address 0034 16) The A-D conversion registers are read-only registers that store the result of an A-D conversion. Do not read these registers during an A-D conversion Analog input pin selection bits b2 b1 b0 0 0 0 0 1 [AD Control Register (ADCON)] 003416 The AD control register controls the A-D conversion process. Bits 0 to 2 select a specific analog input pin. Bit 4 indicates the completion of an A-D conversion. The value of this bit remains at “0” during an A-D conversion and changes to “1” when an A-D conversion ends. Writing “0” to this bit starts the A-D conversion. 0 0 1 1 0 0: P30/AN0 1: P31/AN1 0: P32/AN2 1: P33/AN3 0: P34/AN4 Not used (returns “0” when read) A-D conversion completion bit 0: Conversion in progress 1: Conversion completed Not used (returns “0” when read) Comparison Voltage Generator Fig. 36 Structure of AD control register The comparison voltage generator divides the voltage between AVSS and VREF into 1024 and outputs the divided voltages. Channel Selector 10-bit reading (Read address 003616 before 003516) The channel selector selects one of ports P3 0/AN0 to P34 /AN4 and inputs the voltage to the comparator. b7 b0 b9 b8 b7 b0 (Address 003616) Comparator and Control Circuit The comparator and control circuit compare an analog input voltage with the comparison voltage, and the result is stored in the A-D conversion registers. When an A-D conversion is completed, the control circuit sets the A-D conversion completion bit and the A-D interrupt request bit to “1”. Note that because the comparator consists of a capacitor coupling, set f(XIN) to 500 kHz or more during an A-D conversion. (Address 003516) b7 b6 b5 b4 b3 b2 b1 b0 Note : The high-order 6 bits of address 0036 16 become “0” at reading. 8-bit reading (Read only address 003516) b7 b0 (Address 003516) b9 b8 b7 b6 b5 b4 b3 b2 Fig. 37 Structure of A-D conversion registers Data bus AD control register (Address 0034 16) b7 b0 3 A-D interrupt request A-D control circuit Channel selector P30/AN0 P31/AN 1 P32/AN 2 P33/AN 3 P34/AN 4 Comparator A-D conversion high-order register (Address 0036 16) A-D conversion low-order register (Address 0035 16) 10 Resistor ladder VREF AV SS Fig. 38 Block diagram of A-D converter 33 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER WATCHDOG TIMER ●Watchdog timer H count source selection bit operation Bit 7 of the watchdog timer control register (address 003916) permits selecting a watchdog timer H count source. When this bit is set to “0”, the count source becomes the underflow signal of watchdog timer L. The detection time is set to 131.072 ms at f(XIN) = 8 MHz frequency and 32.768 s at f(XCIN ) = 32 kHz frequency. When this bit is set to “1”, the count source becomes the signal divided by 16 for f(XIN) (or f(XCIN )). The detection time in this case is set to 512 µs at f(XIN) = 8 MHz frequency and 128 ms at f(XCIN ) = 32 kHz frequency. This bit is cleared to “0” after resetting. The watchdog timer gives a mean of returning to the reset status when a program cannot run on a normal loop (for example, because of a software run-away). The watchdog timer consists of an 8-bit watchdog timer L and an 8-bit watchdog timer H. Standard Operation of Watchdog Timer When any data is not written into the watchdog timer control register (address 003916) after resetting, the watchdog timer is in the stop state. The watchdog timer starts to count down by writing an optional value into the watchdog timer control register (address 003916 ) and an internal reset occurs at an underflow of the watchdog timer H. Accordingly, programming is usually performed so that writing to the watchdog timer control register (address 0039 16) may be started before an underflow. When the watchdog timer control register (address 003916) is read, the values of the high-order 6 bits of the watchdog timer H, STP instruction disable bit, and watchdog timer H count source selection bit are read. ●Operation of STP instruction disable bit Bit 6 of the watchdog timer control register (address 003916) permits disabling the STP instruction when the watchdog timer is in operation. When this bit is “0”, the STP instruction is enabled. When this bit is “1”, the STP instruction is disabled, once the STP instruction is executed, an internal reset occurs. When this bit is set to “1”, it cannot be rewritten to “0” by program. This bit is cleared to “0” after resetting. ●Initial value of watchdog timer At reset or writing to the watchdog timer control register (address 003916 ), each watchdog timer H and L is set to “FF16.” “FF16” is set when watchdog timer control register is written to. XCIN XIN “FF16” is set when watchdog timer control register is written to. “0” “10” Main clock division ratio selection bits (Note) Data bus Watchdog timer L (8) 1/16 “1” “00” “01” Watchdog timer H (8) Watchdog timer H count source selection bit STP instruction disable bit STP instruction Reset circuit RESET Internal reset Note: Any one of high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. Fig. 39 Block diagram of Watchdog timer b7 b0 Watchdog timer control register (WDTCON : address 0039 16) Watchdog timer H (for read-out of high-order 6 bit) STP instruction disable bit 0: STP instruction enabled 1: STP instruction disabled Watchdog timer H count source selection bit 0: Watchdog timer L underflow 1: f(XIN)/16 or f(XCIN)/16 Fig. 40 Structure of Watchdog timer control register 34 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER RESET CIRCUIT To reset the microcomputer, RESET pin must be held at an "L" level for 2 µs or more. Then the RESET pin is returned to an "H" level (the power source voltage must be between 2.7 V and 5.5 V, and the oscillation must be stable), reset is released. After the reset is completed, the program starts from the address contained in address FFFD16 (high-order byte) and address FFFC 16 (low-order byte). Make sure that the reset input voltage is less than 0.54 V for VCC of 2.7 V. Poweron RESET Power source voltage 0V VCC Reset input voltage 0V (Note) 0.2VCC Note : Reset release voltage ; Vcc=2.7 V RESET VCC Power source voltage detection circuit Fig. 41 Reset circuit example XIN φ RESET RESETOUT ? ? Address ? ? FFFC FFFD ADH,L Reset address from the vector table. ? Data ? ? ? ADL ADH SYNC XIN: 8 to 13 clock cycles Notes 1: The frequency relation of f(X IN) and f(φ) is f(XIN) = 2 • f(φ). 2: The question marks (?) indicate an undefined state that depends on the previous state. 3: All signals except X IN and RESET are internals. Fig. 42 Reset sequence 35 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Address Register contents (1) Port P0 direction register (P0D) 000116 0016 (2) Port P1 direction register (P1D) 000316 0016 (3) Port P2 direction register (P2D) 000516 0016 (4) Port P3 direction register (P3D) 000716 0016 (5) Port P4 direction register (P4D) 000916 0016 (6) Serial I/O status register (SIOSTS) 001916 1 0 0 0 0 0 0 0 (7) Serial I/O control register (SIOCON) 001A16 (8) UART control register (UARTCON) 001B16 1 1 1 0 0 0 0 0 (9) PWM control register (PWMCON) 001D16 0016 (10) Prescaler 12 (PRE12) 002016 FF16 (11) Timer 1 (T1) 002116 0116 (12) Timer 2 (T2) 002216 0016 (13) Timer XY mode register (TM) 002316 0016 (14) Prescaler X (PREX) 002416 FF16 (15) Timer X (TX) 002516 FF16 (16) Prescaler Y (PREY) 002616 FF16 (17) Timer Y (TY) 002716 FF16 (18) Timer count source select register 002816 0016 (19) I2C address register (S0D) 002C16 0016 (20) I2C status register (S1) 002D16 0 0 0 1 0 0 0 X (21) I2C control register (S1D) 002E16 0016 (22) I2C clock control register (S2) 002F16 0016 (23) I2C start/stop condition control register (S2D) 003016 0 0 0 1 1 0 1 0 (24) AD control register (ADCON) 003416 0 0 0 1 0 0 0 0 (25) MISRG 003816 (26) Watchdog timer control register (WDTCON) 003916 0 0 1 1 1 1 1 1 (27) Interrupt edge selection register (INTEDGE) 003A16 (28) CPU mode register (CPUM) 003B16 0 1 0 0 1 0 0 0 (29) Interrupt request register 1 (IREQ1) 003C16 0016 (30) Interrupt request register 2 (IREQ2) 003D16 0016 (31) Interrupt control register 1 (ICON1) 003E16 0016 (32) Interrupt control register 2 (ICON2) 003F16 0016 (33) Processor status register (34) Program counter Note : X indicates Not fixed . Fig. 43 Internal status at reset 36 0016 0016 0016 (PS) X X X X X 1 X X (PCH) FFFD16 contents (PCL) FFFC16 contents MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER CLOCK GENERATING CIRCUIT The 3851 group has two built-in oscillation circuits. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT (XCIN and X COUT). Use the circuit constants in accordance with the resonator manufacturer’s recommended values. No external resistor is needed between XIN and XOUT since a feed-back resistor exists on-chip. However, an external feed-back resistor is needed between XCIN and X COUT. Immediately after power on, only the XIN oscillation circuit starts oscillating, and XCIN and X COUT pins function as I/O ports. Frequency Control (1) Middle-speed mode The internal clock φ is the frequency of X IN divided by 8. After reset, this mode is selected. (2) High-speed mode be generated. (2) Wait mode If the WIT instruction is executed, the internal clock φ stops at an “H” level, but the oscillator does not stop. The internal clock φ restarts at reset or when an interrupt is received. Since the oscillator does not stop, normal operation can be started immediately after the clock is restarted. To ensure that the interrupts will be received to release the STP or WIT state, their interrupt enable bits must be set to “1” before executing of the STP or WIT instruction. When releasing the STP state, the prescaler 12 and timer 1 will start counting the clock XIN divided by 16. Accordingly, set the timer 1 interrupt enable bit to “0” before executing the STP instruction. The internal clock φ is half the frequency of XIN . ■Note (3) Low-speed mode When using the oscillation stabilizing time set after STP instruction released bit set to “1”, evaluate time to stabilize oscillation of the used oscillator and set the value to the timer 1 and prescaler 12. The internal clock φ is half the frequency of XCIN . ■Note If you switch the mode between middle/high-speed and lowspeed, stabilize both X IN and XCIN oscillations. The sufficient time is required for the sub-clock to stabilize, especially immediately after power on and at returning from the stop mode. When switching the mode between middle/high-speed and low-speed, set the frequency on condition that f(XIN) > 3•f(XCIN). XCIN XCOUT Rf XIN XOUT Rd (4) Low power dissipation mode The low power consumption operation can be realized by stopping the main clock XIN in low-speed mode. To stop the main clock, set bit 5 of the CPU mode register to “1.” When the main clock XIN is restarted (by setting the main clock stop bit to “0”), set sufficient time for oscillation to stabilize. The sub-clock XCIN -XCOUT oscillating circuit can not directly input clocks that are generated externally. Accordingly, make sure to cause an external resonator to oscillate. Oscillation Control (1) Stop mode If the STP instruction is executed, the internal clock φ stops at an “H” level, and XIN and XCIN oscillation stops. When the oscillation stabilizing time set after STP instruction released bit is “0,” the prescaler 12 is set to “FF16 ” and timer 1 is set to “0116 .” When the oscillation stabilizing time set after STP instruction released bit is “1,” set the sufficient time for oscillation of used oscillator to stabilize since nothing is set to the prescaler 12 and timer 1. Either XIN or X CIN divided by 16 is input to the prescaler 12 as count source. Oscillator restarts when an external interrupt is received, but the internal clock φ is not supplied to the CPU (remains at “H”) until timer 1 underflows. The internal clock φ is supplied for the first time, when timer 1 underflows. This ensures time for the clock oscillation using the ceramic resonators to be stabilized. When the oscillator is restarted by reset, apply “L” level to the RESET pin until the oscillation is stable since a wait time will not CCIN CCOUT CIN COUT Fig. 44 Ceramic resonator circuit XCIN XCOUT Rf XIN XOUT Open Rd External oscillation circuit CCIN CCOUT Vcc Vss Fig. 45 External clock input circuit 37 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 MISRG (MISRG : address 0038 16) Oscillation stabilizing time set after STP instruction released bit 0: Automatically set “01 16 ” to Timer 1, “FF 16 ” to Prescaler 12 1: Automatically set nothing Reserved bit “0” Do not write “1“. Not used (return “0” when read) Fig. 46 Structure of MISRG XCOUT XCIN “0” “1” Port XC switch bit XOUT XIN Main clock division ratio selection bits (Note) Low-speed mode 1/2 1/4 Prescaler 12 1/2 High-speed or middle-speed mode FF16 Timer 1 0116 Reset or STP instruction Main clock division ratio selection bits (Note) Middle-speed mode Timing φ (internal clock) High-speed or low-speed mode Main clock stop bit Q S R S Q STP instruction WIT instruction R Q S R STP instruction Reset Interrupt disable flag l Interrupt request Note: Any one of high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. When low-speed mode is selected, set port Xc switch bit (b1) to “1”. Fig. 47 System clock generating circuit block diagram (Single-chip mode) 38 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Reset 4 CM7=0 CM6=0 CM5=0(8 MHz oscillating) CM4=0(32 kHz stopped) C “0 M4 CM ”← “1 6 →“ 1” ”← → “0 ” ” “0 → CM ”← 0” “1 M6 →“ C ”← “1 High-speed mode (f(φ)=4 MHz) CM 6 “1”←→“0” “1 C “0 M7 CM ”←→ 6 ”← → CM 4 “1”←→“0” CM 4 “1”←→“0” CM7=0 CM6=1 CM5=0(8 MHz oscillating) CM4=0(32 kHz stopped) Middle-speed mode (f(φ)=1 MHz) CM7=0 CM6=1 CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) High-speed mode (f(φ)=4 MHz) CM 6 “1”←→“0” CM7=0 CM6=0 CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) “1 ” “0 ” CM 7 “1”←→“0” Middle-speed mode (f(φ)=1 MHz) Low-speed mode (f(φ)=16 kHz) CM 5 “1”←→“0” CM7=1 CM6=0 CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) Low-speed mode (f(φ)=16 kHz) CM7=1 CM6=0 CM5=1(8 MHz stopped) CM4=1(32 kHz oscillating) b7 b4 CPU mode register (CPUM : address 003B 16) CM4 : Port Xc switch bit 0 : I/O port function (stop oscillating) 1 : X CIN-XCOUT oscillating function CM5 : Main clock (X IN- XOUT) stop bit 0 : Operating 1 : Stopped CM7, CM6: Main clock division ratio selection bit b7 b6 0 0 : φ = f(XIN)/2 ( High-speed mode) 0 1 : φ = f(XIN)/8 (Middle-speed mode) 1 0 : φ = f(XCIN)/2 (Low-speed mode) 1 1 : Not available Notes 1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the modes directly without an allow.) 2 : The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is ended. 3 : Timer operates in the wait mode. 4 : When the stop mode is ended, a delay of approximately 1 ms occurs by connecting prescaler 12 in middle/high-speed mode. 5 : When the stop mode is ended, a delay of approximately 16 ms occurs by Timer 1 and Timer 2 in low-speed mode. 6 : Wait until oscillation stabilizes after oscillating the main clock X IN before the switching from the low-speed mode to middle/high-speed mode. 7 : The example assumes that 8 MHz is being applied to the X IN pin and 32 kHz to the X CIN pin. φ indicates the internal clock. Fig. 48 State transitions of system clock 39 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER NOTES ON PROGRAMMING Processor Status Register A-D Converter The contents of the processor status register (PS) after a reset are undefined, except for the interrupt disable flag (I) which is “1.” After a reset, initialize flags which affect program execution. In particular, it is essential to initialize the index X mode (T) and the decimal mode (D) flags because of their effect on calculations. The comparator uses internal capacitors whose charge will be lost if the clock frequency is too low. Therefore, make sure that f(XIN) is at least on 500 kHz during an A-D conversion. Do not execute the STP or WIT instruction during an A-D conversion. Interrupts Instruction Execution Time The contents of the interrupt request bits do not change immediately after they have been written. After writing to an interrupt request register, execute at least one instruction before performing a BBC or BBS instruction. The instruction execution time is obtained by multiplying the frequency of the internal clock φ by the number of cycles needed to execute an instruction. The number of cycles required to execute an instruction is shown in the list of machine instructions. The frequency of the internal clock φ is half of the XIN frequency in high-speed mode. Decimal Calculations • To calculate in decimal notation, set the decimal mode flag (D) to “1”, then execute an ADC or SBC instruction. After executing an ADC or SBC instruction, execute at least one instruction before executing a SEC, CLC, or CLD instruction. • In decimal mode, the values of the negative (N), overflow (V), and zero (Z) flags are invalid. Timers If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1). Multiplication and Division Instructions • The index X mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instruction. • The execution of these instructions does not change the contents of the processor status register. Ports The contents of the port direction registers cannot be read. The following cannot be used: • The data transfer instruction (LDA, etc.) • The operation instruction when the index X mode flag (T) is “1” • The addressing mode which uses the value of a direction register as an index • The bit-test instruction (BBC or BBS, etc.) to a direction register • The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a direction register. Use instructions such as LDM and STA, etc., to set the port direction registers. Serial I/O In clock synchronous serial I/O, if the receive side is using an external clock and it is to output the S RDY signal, set the transmit enable bit, the receive enable bit, and the SRDY output enable bit to “1.” Serial I/O continues to output the final bit from the TXD pin after transmission is completed. When an external clock is used as synchronous clock in serial I/O, write transmission data to the transmit buffer register while the transfer clock is “H.” 40 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER DATA REQUIRED FOR MASK ORDERS ROM PROGRAMMING METHOD The following are necessary when ordering a mask ROM production: 1.Mask ROM Order Confirmation Form 2.Mark Specification Form 3.Data to be written to ROM, in EPROM form (three identical copies) The built-in PROM of the blank One Time PROM version and builtin EPROM version can be read or programmed with a general-purpose PROM programmer using a special programming adapter. Set the address of PROM programmer in the user ROM area. Table 10 Programming adapter D ATA REQUIRE D FOR ROM WRI T I NG ORDERS The following are necessary when ordering a ROM writing: 1.ROM Writing Confirmation Form 2.Mark Specification Form 3.Data to be written to ROM, in EPROM form (three identical copies) Package Name of Programming Adapter 42P2R-A PCA4738F-42A 42P4B PCA4738S-42A The PROM of the blank One Time PROM version is not tested or screened in the assembly process and following processes. To ensure proper operation after programming, the procedure shown in Figure 49 is recommended to verify programming. Programming with PROM programmer Screening (Caution) (150 °C for 40 hours) Verification with PROM programmer Functional check in target device Caution : The screening temperature is far higher than the storage temperature. Never expose to 150 °C exceeding 100 hours. Fig. 49 Programming and testing of One Time PROM version 41 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ELECTRICAL CHARACTERISTICS Table 11 Absolute maximum ratings Symbol VCC VI VI VI VI VO VO Pd Topr Tstg Parameter Power source voltage Input voltage P00–P07, P10 –P17, P20, P21, P24–P27, P30 –P34, P40–P44 , VREF Input voltage P22, P23 Input voltage RESET, XIN Input voltage CNVSS Output voltage P00–P07, P10 –P17, P20, P21, P24–P27, P30 –P34, P40–P44 , XOUT Output voltage P22, P23 Power dissipation Operating temperature Storage temperature Conditions All voltages are based on VSS. Output transistors are cut off. Ratings –0.3 to 7.0 Unit V –0.3 to VCC +0.3 V –0.3 to 5.8 –0.3 to VCC +0.3 –0.3 to 13 V V V –0.3 to VCC +0.3 V –0.3 to 5.8 300 –20 to 85 –40 to 125 V mW °C °C Ta = 25 °C Table 12 Recommended operating conditions (1) (VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol VCC VSS VREF AVSS VIA VIH VIH VIH VIH VIH VIH VIL VIL VIL VIL VIL ΣI OH(peak) ΣI OH(peak) ΣI OL(peak) ΣI OL(peak) ΣI OL(peak) ΣI OH(avg) ΣI OH(avg) ΣI OL(avg) ΣI OL(avg) ΣI OL(avg) Parameter Power source voltage (At 8 MHz) Power source voltage (At 4 MHz) Power source voltage A-D convert reference voltage Analog power source voltage Analog input voltage AN 0–AN4 “H” input voltage P00–P07, P10 –P17, P20–P27 , P30–P34, P40 –P44 “H” input voltage (when I2C-BUS input level is selected) SDA1, SCL1 “H” input voltage (when I2C-BUS input level is selected) SDA2, SCL2 “H” input voltage (when SMBUS input level is selected) SDA1, SCL1 “H” input voltage (when SMBUS input level is selected) SDA2, SCL2 “H” input voltage RESET, XIN, CNV SS “L” input voltage P00–P07, P10 –P17, P20–P27 , P30–P34, P40 –P44 “L” input voltage (when I2 C-BUS input level is selected) SDA1, SDA2, SCL1, SCL2 “L” input voltage (when SMBUS input level is selected) SDA1, SDA2, SCL1, SCL2 “L” input voltage RESET, CNV SS “L” input voltage XIN “H” total peak output current P00–P07 , P10–P17, P3 0–P34 (Note) “H” total peak output current P20, P2 1, P24–P27, P4 0–P44 (Note) “L” total peak output current P00–P07 , P10–P12, P3 0–P34 (Note) “L” total peak output current P13–P17 (Note) “L” total peak output current P20 –P27 ,P40 –P44 (Note) “H” total average output current P00–P07 , P10–P17, P3 0–P34 (Note) “H” total average output current P20, P2 1, P24–P27, P4 0–P44 (Note) “L” total average output current P00–P07 , P10–P12, P3 0–P34 (Note) “L” total average output current P13–P17 (Note) “L” total average output current P20 –P27 ,P40 –P44 (Note) Limits Min. 4.0 2.7 Typ. 5.0 5.0 0 Max. 5.5 5.5 Unit V AVSS 0.8VCC VCC VCC V V V V V 0.7VCC 5.8 V 0.7VCC VCC V 1.4 5.8 V 1.4 VCC V 0.8VCC 0 VCC 0.2V CC V V 0 0.3V CC V 0 0.6 V 0 0.2V CC 0.16VCC V V –80 –80 80 80 80 –40 –40 40 40 40 mA mA mA mA mA mA mA mA mA mA 2.0 VCC 0 0 Note : The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100 ms. The total peak current is the peak value of all the currents. 42 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 13 Recommended operating conditions (2) (VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol I OH(peak) I OL(peak) I OL(peak) I OH(avg) I OL(avg) I OL(avg) f(XIN ) f(XIN ) Parameter “H” peak output current P00 –P07, P10–P17 , P20, P21, P2 4–P27, P30–P34 , P40 –P44 (Note 1) “L” peak output current P00 –P07, P10–P12 , P20–P27, P30 –P34, P40–P44 (Note 1) “L” peak output current P13 –P17 (Note 1) “H” average output current P00 –P07, P10–P17 , P20, P21, P2 4–P27, P30–P34 , P40 –P44 (Note 2) “L” average output current P00 –P07, P10–P12 , P20–P27, P30 –P34, P40–P44 (Note 2) “L” peak output current P13 –P17 (Note 2) Internal clock oscillation frequency (VCC = 4.0 to 5.5V) (Note 3) Internal clock oscillation frequency (VCC = 2.7 to 5.5V) (Note 3) Min. Limits Typ. Max. Unit –10 mA 10 mA 20 mA –5 mA 5 mA 15 8 4 mA MHz kHz Notes 1: The peak output current is the peak current flowing in each port. 2: The average output current I OL(avg), IOH(avg) are average value measured over 100 ms. 3: When the oscillation frequency has a duty cycle of 50%. 43 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 14 Electrical characteristics (VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Limits Symbol VOH VOL VOL Parameter “H” output voltage P00–P07 , P10–P17, P20 , P21, P24–P27 , P30–P34, P40–P44 (Note) “L” output voltage P00–P07 , P10–P12, P20–P27 P30–P34 , P40–P44 “L” output voltage P13–P17 Test conditions I OH = –10 mA VCC = 4.0–5.5 V I OH = –1.0 mA VCC = 2.7–5.5 V I OL = 10 mA VCC = 4.0–5.5 V I OL = 1.0 mA VCC = 2.7–5.5 V I OL = 20 mA VCC = 4.0–5.5 V I OL = 10 mA VCC = 2.7–5.5 V Min. Typ. Max. Unit VCC–2.0 V VCC–1.0 V 2.0 V 1.0 V 2.0 V 1.0 V VT+–VT– Hysteresis CNTR0, CNTR 1, INT 0–INT3 0.4 V VT+–VT– Hysteresis RxD, SCLK, SDA1, SDA2, SCL1, SCL2 0.5 V 0.5 V VT+–VT– I IH I IH I IH I IL I IL I IL VRAM Hysteresis RESET “H” input current P00–P07 , P10–P17, P20 , P21, P24–P27 , P30–P34, P40–P44 “H” input current RESET, CNV SS “H” input current XIN “L” input current P00–P07 , P10–P17, P20–P27 P30–P34 , P40–P44 “L” input current RESET,CNVSS “L” input current XIN RAM hold voltage 5.0 µA 5.0 µA µA VI = V SS –5.0 µA VI = V SS VI = V SS When clock stopped –5.0 µA µA V VI = V CC VI = V CC VI = V CC 4 –4 2.0 Note: P25 is measured when the P25/TX D P-channel output disable bit of the UART control register (bit 4 of address 001B 16) is “0”. 44 5.5 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 15 Electrical characteristics (VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol I CC Limits Parameter Power source current Test conditions High-speed mode f(XIN ) = 8 MHz f(XCIN ) = 32.768 kHz Output transistors “off” High-speed mode f(XIN) = 8 MHz (in WIT state) f(XCIN ) = 32.768 kHz Output transistors “off” Low-speed mode f(XIN ) = stopped f(XCIN ) = 32.768 kHz Output transistors “off” Low-speed mode f(XIN) = stopped f(XCIN ) = 32.768 kHz (in WIT state) Output transistors “off” Low-speed mode (VCC = 3 V) f(XIN) = stopped f(XCIN ) = 32.768 kHz Output transistors “off” Low-speed mode (VCC = 3 V) f(XIN ) = stopped f(XCIN ) = 32.768 kHz (in WIT state) Output transistors “off” Middle-speed mode f(XIN ) = 8 MHz f(XCIN ) = stopped Output transistors “off” Middle-speed mode f(XIN) = 8 MHz (in WIT state) f(XCIN ) = stopped Output transistors “off” Increment when A-D conversion is executed f(XIN ) = 8 MHz All oscillation stopped (in STP state) Output transistors “off” Ta = 25 °C Ta = 85 °C Min. Typ. Max. 6.8 13 Unit mA mA 1.6 60 200 µA 20 40 µA 20 55 µA 5.0 10.0 µA 4.0 7.0 mA 1.5 mA 800 µA 0.1 1.0 µA 10 µA 45 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 16 A-D converter characteristics (VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, f(XIN) = 8 MHz, unless otherwise noted) Symbol Parameter – – Resolution Absolute accuracy (excluding quantization error) Conversion time Ladder resistor Reference power source input current A-D port input current t CONV RLADDER I VREF I I(AD) 46 Test conditions VREF = 5.0 V Limits Min. 50 Typ. 35 150 0.5 Max. 10 ±4 61 200 5.0 Unit bit LSB tc(φ) kΩ µA µA MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TIMING REQUIREMENTS Table 17 Timing requirements (1) (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol t W(RESET) t C(X IN) t WH (XIN) t WL (XIN) t C(CNTR) t WH (CNTR) t WL(CNTR) t C(S CLK) t WH (SCLK) t WL (SCLK) t su(Rx D-SCLK) t h(S CLK-Rx D) Parameter Reset input “L” pulse width External clock input cycle time External clock input “H” pulse width External clock input “L” pulse width CNTR0, CNTR1 input cycle time CNTR0, CNTR1, INT 0–INT3 input “H” pulse width CNTR0, CNTR1, INT0–INT3 input “L” pulse width Serial I/O clock input cycle time (Note) Serial I/O clock input “H” pulse width (Note) Serial I/O clock input “L” pulse width (Note) Serial I/O input setup time Serial I/O input hold time Min. 2 125 50 50 200 80 80 800 370 370 220 100 Limits Typ. Max. Unit µs ns ns ns ns ns ns ns ns ns ns ns Note : When f(XIN ) = 8 MHz and bit 6 of address 001A16 is “1” (clock synchronous). Divide this value by four when f(XIN ) = 8 MHz and bit 6 of address 001A16 is “0” (UART). Table 18 Timing requirements (2) (VCC = 2.7 to 4.0 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol t W(RESET) t C(X IN) t WH (XIN) t WL (XIN) t C(CNTR) t WH (CNTR) t WL(CNTR) t C(S CLK) t WH (SCLK) t WL (SCLK) t su(Rx D-SCLK) t h(S CLK-Rx D) Parameter Reset input “L” pulse width External clock input cycle time External clock input “H” pulse width External clock input “L” pulse width CNTR0, CNTR1 input cycle time CNTR0, CNTR1, INT 0–INT3 input “H” pulse width CNTR0, CNTR1, INT0–INT3 input “L” pulse width Serial I/O clock input cycle time (Note) Serial I/O clock input “H” pulse width (Note) Serial I/O clock input “L” pulse width (Note) Serial I/O input setup time Serial I/O input hold time Limits Min. 2 250 100 100 500 230 230 2000 950 950 400 200 Typ. Max. Unit µs ns ns ns ns ns ns ns ns ns ns ns Note : When f(XIN ) = 8 MHz and bit 6 of address 001A16 is “1” (clock synchronous). Divide this value by four when f(XIN ) = 8 MHz and bit 6 of address 001A16 is “0” (UART). 47 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 19 Switching characteristics 1 (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol t WH (S CLK) t WL (S CLK) t d (SCLK -TXD) t V (S CLK-TXD) t r (SCLK ) t f (S CLK) t r (CMOS) t f (CMOS) Parameter Serial I/O clock output “H” pulse width Serial I/O clock output “L” pulse width Serial I/O output delay time (Note 1) Serial I/O output valid time (Note 1) Serial I/O clock output rising time Serial I/O clock output falling time CMOS output rising time (Note 2) CMOS output falling time (Note 2) Limits Min. Typ. Max. t C(SCLK )/2–30 t C(SCLK )/2–30 140 –30 10 10 30 30 30 30 Unit ns ns ns ns ns ns ns ns Notes 1: For t WH(SCLK), tWL (SCLK), when the P51/TX D P-channel output disable bit of the UART control register (bit 4 of address 001B16) is “0”. 2: The XOUT pin is excluded. Table 20 Switching characteristics 2 (VCC = 2.7 to 4.0 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol t WH (S CLK) t WL (SCLK ) t d (SCLK -TXD) t V (S CLK-TXD) t r (SCLK ) t f (S CLK) t r (CMOS) t f (CMOS) Parameter Serial I/O clock output “H” pulse width Serial I/O clock output “L” pulse width Serial I/O output delay time (Note 1) Serial I/O output valid time (Note 1) Serial I/O clock output rising time Serial I/O clock output falling time CMOS output rising time (Note 2) CMOS output falling time (Note 2) Limits Min. Typ. tC (SCLK)/2–50 tC (SCLK)/2–50 Max. 350 –30 20 20 50 50 50 50 Notes 1: For t WH(SCLK), tWL (SCLK), when the P51/TX D P-channel output disable bit of the UART control register (bit 4 of address 001B16) is “0”. 2: The XOUT pin is excluded. 48 Unit ns ns ns ns ns ns ns ns MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 1kΩ Measurement output pin Measurement output pin 100pF 100pF CMOS output Fig. 50 Circuit for measuring output switching characteristics (1) N-channel open-drain output Fig. 51 Circuit for measuring output switching characteristics (2) 49 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER tC(CNTR) tWL(CNTR) tWH(CNTR) 0.8VCC CNTR0, CNTR1 0.2VCC tWL(INT) tWH(INT) 0.8VCC INT0 to INT3 0.2VCC tW(RESET) RESET 0.8VCC 0.2VCC tC(XIN) tWL(XIN) tWH(XIN) 0.8VCC XIN tf SCLK 0.2VCC tWL(S CLK) tC(SCLK) tr 0.8VCC 0.2VCC tsu(RxD-SCLK) td(SCLK-TXD) Fig. 52 Timing diagram 50 th(SCLK-RxD) 0.8VCC 0.2VCC RXD TX D tWH(SCLK) tv(SCLK-TXD) MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MULTI-MASTER I2C-BUS BUS LINE CHARACTERISTICS Table 21 Multi-master I2C-BUS bus line characteristics Standard clock mode Symbol Parameter Min. Max. High-speed clock mode Max. Unit t BUF Bus free time 4.7 Min. 1.3 t HD;STA Hold time for START condition 4.0 0.6 µs t LOW Hold time for S CL clock = “0” 4.7 1.3 µs tR Rising time of both SCL and SDA signals t HD;DAT Data hold time t HIGH Hold time for S CL clock = “1” tF Falling time of both S CL and SDA signals t SU;DAT Data setup time 1000 20+0.1Cb 0 0 4.0 0.6 300 250 µs 300 ns 0.9 µs µs 20+0.1Cb 300 ns 100 ns t SU;STA Setup time for repeated START condition 4.7 0.6 µs t SU;STO Setup time for STOP condition 4.0 0.6 µs Note: C b = total capacitance of 1 bus line SDA tHD:STA tBUF tLOW SCL P tR tF S tHD:STA Sr tHD:DAT tsu:STO tHIGH tsu:DAT P tsu:STA S : START condition Sr : RESTART condition P : STOP condition Fig. 53 Timing diagram of multi-master I2C-BUS 51 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MASK ROM CONFIRMATION FORM GZZ-SH52-61B<83A0> Mask ROM number 740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38513M4-XXXSP/FP MITSUBISHI ELECTRIC Date: Receipt Section head Supervisor signature signature Note : Please fill in all items marked ❈. Date issued ) Date: Submitted by Issuance signature ❈ Customer TEL ( Company name Supervisor ❈ 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name: M38513M4-XXXSP M38513M4-XXXFP Checksum code for entire EPROM (hexadecimal notation) EPROM type (indicate the type used) 27512 27256 EPROM address 000016 Product name 000F16 001016 407F16 408016 7FFD16 7FFE16 7FFF16 ASCII code : ‘M38513M4-’ data ROM (16K-130) bytes In the address space of the microcomputer, the internal ROM area is from address C08016 to FFFD16. The reset vector is stored in addresses FFFC16 and FFFD16. EPROM address 000016 Product name 000F16 001016 C07F16 C08016 FFFD16 FFFE16 FFFF16 ASCII code : ‘M38513M4-’ data ROM (16K-130) bytes Address 000016 000116 000216 000316 000416 000516 000616 000716 (1) Set the data in the unused area (the shaded area of the diagram) to “FF16 ”. (2) The ASCII codes of the product name “M38513M4–” must be entered in addresses 0000 16 to 0008 16. And set the data “FF 16” in addresses 000916 to 000F 16. The ASCII codes and addresses are listed to the right in hexadecimal notation. (1/2) 52 ‘M’ = 4D16 ‘3’ = 33 16 ‘8’ = 38 16 ‘5’ = 35 16 ‘1’ = 31 16 ‘3’ = 33 16 ‘M’ = 4D16 ‘4’ = 34 16 Address 000816 000916 000A16 000B16 000C 16 000D 16 000E16 000F 16 ‘–’ = 2D16 FF 16 FF 16 FF 16 FF 16 FF 16 FF 16 FF 16 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GZZ-SH52-61B<83A0> Mask ROM number 740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38513M4-XXXSP/FP MITSUBISHI ELECTRIC We recommend the use of the following pseudo-command to set the start address of the assembler source program because ASCII codes of the product name are written to addresses 000016 to 0008 16 of EPROM. EPROM type 27256 27512 The pseudo-command *= $8000 .BYTE ‘M38513M4–’ *= $0000 .BYTE ‘M38513M4–’ Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation form, the ROM will not be processed. ❈ 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Fill out the appropriate mark specification form (42P4B for M38513M4-XXXSP, 42P2R for M38513M4-XXXFP) and attach it to the mask ROM confirmation form. ❈ 3. Usage conditions Please answer the following questions about usage for use in our product inspection : (1) How will you use the X IN-XOUT oscillator? Ceramic resonator Quartz crystal External clock input Other ( At what frequency? ) MHz f(XIN) = (2) Which function will you use the pins P21/X CIN and P20/XCOUT as P21 and P20 , or XCIN and XCOUT ? Ports P21 and P20 function XCIN and XCOUT function (external resonator) (3) Will you use the I2C-BUS function or the SM-BUS function ? I2C-BUS function used SM-BUS function used Not used ❈ 4. Comments (2/2) 53 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ROM PROGRAMMING CONFIRMATION FORM GZZ-SH11-43A<6YB0> ROM number Date: Section head Supervisor signature signature Receipt 740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38513E4-XXXSP/FP MITSUBISHI ELECTRIC Note : Please fill in all items marked ❈. Date issued Date: ) Submitted by Issuance signature ❈ Customer TEL ( Company name Supervisor ❈ 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce ROM programming based on this data. We shall assume the responsibility for errors only if the programming data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name: M38513E4-XXXSP M38513E4-XXXFP Checksum code for entire EPROM (hexadecimal notation) EPROM type (indicate the type used) 27512 27256 EPROM address 000016 Product name 000F16 001016 407F16 408016 7FFD16 7FFE16 7FFF16 ASCII code : ‘M38513E4-’ data ROM (16K-130) bytes In the address space of the microcomputer, the internal ROM area is from address C08016 to FFFD16. The reset vector is stored in addresses FFFC16 and FFFD16. EPROM address 000016 Product name 000F16 001016 C07F16 C08016 FFFD16 FFFE16 FFFF16 ASCII code : ‘M38513E4-’ data ROM (16K-130) bytes Address 000016 000116 000216 000316 000416 000516 000616 000716 (1) Set the data in the unused area (the shaded area of the diagram) to “FF16 ”. (2) The ASCII codes of the product name “M38513E4–” must be entered in addresses 0000 16 to 0008 16. And set the data “FF 16” in addresses 000916 to 000F 16. The ASCII codes and addresses are listed to the right in hexadecimal notation. (1/2) 54 ‘M’ = 4D16 ‘3’ = 33 16 ‘8’ = 38 16 ‘5’ = 35 16 ‘1’ = 31 16 ‘3’ = 33 16 ‘E’ = 45 16 ‘4’ = 34 16 Address 000816 000916 000A16 000B16 000C 16 000D 16 000E16 000F 16 ‘–’ = 2D16 FF 16 FF 16 FF 16 FF 16 FF 16 FF 16 FF 16 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GZZ-SH11-43A<6YB0> ROM number 740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38513E4-XXXSP/FP MITSUBISHI ELECTRIC We recommend the use of the following pseudo-command to set the start address of the assembler source program because ASCII codes of the product name are written to addresses 000016 to 0008 16 of EPROM. EPROM type 27256 27512 The pseudo-command *= $8000 .BYTE ‘M38513E4–’ *= $0000 .BYTE ‘M38513E4–’ Note : If the name of the product written to the EPROMs does not match the name of the ROM programming confirmation form, the ROM will not be processed. ❈ 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Fill out the appropriate mark specification form; 42P2R for the M38513E4-XXXFP, the shrink DIP package Mark Specification Form (only for built-in One Time PROM microcomputer) for the M38513E4-XXXSP; and attach it to the ROM programming confirmation form. ❈ 3. Usage conditions Please answer the following questions about usage for use in our product inspection : (1) How will you use the X IN-XOUT oscillator? Ceramic resonator Quartz crystal External clock input Other ( At what frequency? ) MHz f(XIN) = (2) Which function will you use the pins P21/X CIN and P20/XCOUT as P21 and P20 , or XCIN and XCOUT ? Ports P21 and P20 function (3) Will you use the I2C-BUS XCIN and XCOUT function (external resonator) function or the SM-BUS function ? I2C-BUS function used SM-BUS function used Not used ❈ 4. Comments (2/2) 55 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MARK SPECIFICATION FORM 56 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 57 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER SHRINK DIP MARK SPECIFICATION FORM for One Time PROM version microcomputers Enter the catalog number of the microcomputer for which this mark specification is intended. (If you do not know the ROM code number, enter XXX in its place.) The catalog number of the microcomputer M A. Standard Mitsubishi Mark Customer specified part number will be printed together with the ROM code number on the top line. Enter the desired part number left aligned in the box below. (up to 10 characters) Note2 : RXXX Mitsubishi catalog name (blank model number before writing) Mitsubishi lot number (6-digit or 7-digit) Note1 : The following characters can be used in the part number : Uppercase alphabet, numbers, ampersand, hyphen, period, comma, +, /, (, ), ( will be printed at 1.5 x character width) 2 : XXX is the ROM code number. B. Special Mark Required If you desire anything other than the standard Mitsubishi mark, it will be treated as a special mark. Special marks will take longer to produce and should be avoided if possible. If a special mark is to be printed, indicate the desired layout of the mark in the figure below. The layout will be duplicated as closely as possible. Note1 : If the customer’s trademark logo must be used in the Special Mark, please submit a clean original logo. Note that special marks require extra cost and time to produce. 58 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PACKAGE OUTLINE 42P2R-A Plastic 42pin 450mil SSOP EIAJ Package Code SSOP42-P-450-0.80 Weight(g) 0.63 JEDEC Code – Lead Material Alloy 42/Cu Alloy e b2 22 E HE e1 I2 42 F Recommended Mount Pad Symbol 21 1 A D y b L L1 e A1 A2 c A A1 A2 b c D E e HE L L1 y b2 e1 I2 Detail F 42P4B Dimension in Millimeters Min Nom Max – – 2.4 0.05 – – – 2.0 – 0.35 0.4 0.5 0.13 0.15 0.2 17.3 17.5 17.7 8.2 8.4 8.6 – 0.8 – 11.63 11.93 12.23 0.3 0.5 0.7 – 1.765 – – – 0.15 0° – 10° – 0.5 – – 11.43 – – 1.27 – Plastic 42pin 600mil SDIP Weight(g) 4.1 JEDEC Code – Lead Material Alloy 42/Cu Alloy 22 1 21 E 42 e1 c EIAJ Package Code SDIP42-P-600-1.78 Symbol L A1 A A2 D e SEATING PLANE b1 b b2 A A1 A2 b b1 b2 c D E e e1 L Dimension in Millimeters Min Nom Max – – 5.5 0.51 – – – 3.8 – 0.35 0.45 0.55 0.9 1.0 1.3 0.63 0.73 1.03 0.22 0.27 0.34 36.5 36.7 36.9 12.85 13.0 13.15 – 1.778 – – 15.24 – 3.0 – – 0° – 15° 59 MITSUBISHI MICROCOMPUTERS 3851 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Keep safety first in your circuit designs! ● Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials ● These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. ● Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. ● All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. ● Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. ● The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. ● If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. ● Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein. © 1998 MITSUBISHI ELECTRIC CORP. New publication, effective May. 1998. Specifications subject to change without notice. REVISION DESCRIPTION LIST Rev. No. 1.0 3851 GROUP DATA SHEET Revision Description First Edition Rev. date 980515 (1/1)