MHI200DI5.7Series High Isolation, 2W SIP Single & Dual Output DC/DC Converters Electrical Specifications Key Features: • 2W Output Power Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 15 VDC Input 13.5 24 VDC Input 21.6 Capacitor Filter • 5.7 kV Isolation • 15 kV/µS CMTI Input Voltage Range • 40 Standard Models • Miniature SIP Case Input Filter Typ. 5.0 12.0 15.0 24.0 Max. 5.5 13.2 16.5 26.4 Units Typ. Max. ±5.0 ±1.0 Units % % % 100 ±0.02 mV P - P %/°C Max. Units VDC • -40°C to +80°C Operation Output • Industry Standard Pin-Out Parameter • Low Cost Conditions Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 2 Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit Min. Dual Output, Balanced Loads ±0.1 For VIN Change of 1% ±1.2 See Model Selection Guide See Note 3 ±0.01 Momentary (0.5S Max) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Common Mode Transient Immunity Switching Frequency Conditions Rated For 60 Sec Tested For 1 Sec 500 VDC 100 kHz, 1V Min. 5,200 5,700 10 Typ. VDC G pF kV/µS kHz 7 15 100 Environmental Parameter Conditions Ambient Case Operating Temperature Range MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Min. -40 Typ. +25 -55 Free Air Convection RH, Non-condensing Max. +80 +95 +125 Units 95 % °C °C See Mechanical Diagram (Page 3) Non-Conductive Black Plastic (UL94-V0) 0.08 Oz (2.4g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 2.0 Typ. Max. Units MHours Min. Typ. Max. 9.0 18.0 20.0 30.0 260 Units Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Conditions Input Voltage Surge (0.1 Sec) Lead Temperature 5 VDC Input 12 VDC Input 15 VDC Input 24 VDC Input 1.5 mm From Case for 10 Sec Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Nominal 5 5 5 5 5 5 5 5 5 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 MHI205D-1509DI5.7 5 4.5 - 5.5 MHI212S-03DI5.7 MHI212S-05DI5.7 MHI212S-09DI5.7 MHI212S-12DI5.7 MHI212S-15DI5.7 MHI212D-05DI5.7 MHI212D-09DI5.7 MHI212D-12DI5.7 MHI212D-15DI5.7 12 12 12 12 12 12 12 12 12 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 MHI212D-1509DI5.7 12 10.8 - 13.2 MHI215S-03DI5.7 MHI215S-05DI5.7 MHI215S-09DI5.7 MHI215S-12DI5.7 MHI215S-15DI5.7 MHI215D-05DI5.7 MHI215D-09DI5.7 MHI215D-12DI5.7 MHI215D-15DI5.7 15 15 15 15 15 15 15 15 15 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 MHI215D-1509DI5.7 15 13.5 - 16.5 MHI224S-03DI5.7 MHI224S-05DI5.7 MHI224S-09DI5.7 MHI224S-12DI5.7 MHI224S-15DI5.7 MHI224D-05DI5.7 MHI224D-09DI5.7 MHI224D-12DI5.7 MHI224D-15DI5.7 24 24 24 24 24 24 24 24 24 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 MHI224D-1509DI5.7 24 21.6 - 26.4 MHI205S-03DI5.7 MHI205S-05DI5.7 MHI205S-09DI5.7 MHI205S-12DI5.7 MHI205S-15DI5.7 MHI205D-05DI5.7 MHI205D-09DI5.7 MHI205D-12DI5.7 MHI205D-15DI5.7 Output Current (mA) Voltage Full-Load No-Load (VDC) 446 35 3.3 500 35 5.0 493 35 9.0 492 35 12.0 501 35 15.0 513 35 ±5.0 504 35 ±9.0 504 35 ±12.0 501 35 ±15.0 +15.0 495 35 -9.0 181 17 3.3 211 17 5.0 206 17 9.0 202 17 12.0 201 17 15.0 211 17 ±5.0 207 17 ±9.0 205 17 ±12.0 199 17 ±15.0 +15.0 204 17 -9.0 143 16 3.3 169 16 5.0 160 16 9.0 162 16 12.0 155 16 15.0 165 16 ±5.0 160 16 ±9.0 164 16 ±12.0 161 16 ±15.0 +15.0 159 16 -9.0 90 12 3.3 108 12 5.0 103 12 9.0 102 12 12.0 101 12 15.0 108 12 ±5.0 104 12 ±9.0 104 12 ±12.0 103 12 ±15.0 +15.0 102 12 -9.0 Notes: 1. The specified maximum capacitive load is for each output. 2. Load regulation is measured over a range of 20% IOUT to 100% IOUT. 3. When measuring output ripple & noise, it is recommended that an external capacitor (1 µF typ.) be placed from the +VOUT to the -VOUT pins for single output units and from each output to common for dual output models. 4. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR <1.0⍀ at 100 kHz) capacitor be mounted close to the converter. For 5V input units a 2.2 µF is recommended; for 12V & 15V input units, a 1.0 µF; and for 24V units a 0.47 µF. 5. Operation at no-load will not damage the unit, but they may not meet all specifications. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection tables for the correct rating. MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 Current Current (mA, Max) (mA, Min) 500 400 222 168 132 ±200 ±112 ±84 ±66 66 -110 500 400 222 168 132 ±200 ±112 ±84 ±66 66 -110 500 400 222 168 132 ±200 ±112 ±84 ±66 66 -110 500 400 222 168 132 ±200 ±112 ±84 ±66 66 -110 10.0 8.0 4.4 3.4 2.6 ±4.0 ±2.2 ±1.7 ±1.3 1.3 -2.2 10.0 8.0 4.4 3.4 2.6 ±4.0 ±2.2 ±1.7 ±1.3 1.3 -2.2 10.0 8.0 4.4 3.4 2.6 ±4.0 ±2.2 ±1.7 ±1.3 1.3 -2.2 10.0 8.0 4.4 3.4 2.6 ±4.0 ±2.2 ±1.7 ±1.3 1.3 -2.2 Fuse Capacitive Load Efficiency Regulation Rating Load (%, Typ) Slow-Blow (%, Max) (µF, Max) (mA) 74 80 81 82 79 78 80 80 79 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 80 ±10.0 76 79 81 83 82 79 81 82 83 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 81 ±10.0 77 79 83 83 85 81 84 82 82 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 83 ±10.0 76 77 81 82 82 77 81 81 80 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 81 ±10.0 1,650 940 940 440 440 440 440 200 200 200 440 1,650 940 940 440 440 440 440 200 200 200 440 1,650 940 940 440 440 440 440 200 200 200 440 1,650 940 940 440 440 440 440 200 200 200 440 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 500 500 500 500 300 300 300 300 300 300 300 300 300 300 300 200 200 200 200 200 200 200 200 200 200 200 Derating Curve • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com IGBT Applications Notes: The MHI200x-xxD series is a good choice for IGBT applications. They are designed to withstand the extra stress caused by the high voltage switching transients present in IGBT drive circuits. The MHI2xxD-1509DI5.7 models are specifically designed for use with “962” type drivers. The IGD962 (available from MPD) is a hybrid integrated circuit specifically designed to drive N-channel IGBT modules. It provides the I/O isolation, high speed, drive voltage stability and fault protection required to control most MOS gated power devices. The drawing at right illustrates a typical connection of the MHI205D-1509DI5.7 to the IGD962. For more information on this connection, please contact the factory. Mechanical Dimensions Pin Connections Pin 1 2 5 6 7 Single Output +VIN -VIN -VOUT No Pin +VOUT Pin 1 2 5 6 7 Dual Output +VIN -VIN -VOUT Common +VOUT Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]