Micrel MIC5335-3.3/2.7YMT Dual, high performance 300ma ucap uldo Datasheet

MIC5335
Dual, High Performance 300mA µCap
ULDOTM
General Description
The MIC5335 is a high current density, dual Ultra Low
Dropout (ULDO™) linear regulator. The MIC5335 is
ideally suited for portable electronics which demand
overall high performance in a very small form factor.
The MIC5335 is offered in the ultra small 1.6mm x
®
1.6mm 6-ld Thin MLF package which is only
2.56mm2 in area of the SOT-23, TSOP and the 3mm x
®
3mm MLF
package. The MIC5335 delivers
exceptional thermal performances for those
applications that demand higher power dissipation
requirements in a very small foot print. In addition, the
MIC5335 integrates two high performance 300mA
LDOs with independent enable functions and offers
high PSRR eliminating the need for a bypass
capacitor.
The MIC5335 is a µCap design which enables
operation with very small output capacitors for
stability, thereby reducing required board space and
component cost.
Features
•
•
•
•
•
•
•
•
•
•
•
2.3V to 5.5V input voltage range
Ultra-low dropout voltage: 75mV at 300mA
Ultra Thin 1.6mm x 1.6mm 6 lead MLF® package
Independent enable pins
High PSRR - >65dB
300mA output current per LDO
µCap Stable with 1µF ceramic capacitor
Low quiescent current: 90µA/LDO
Fast turn-on time: 30µs
Thermal Shutdown Protection
Current Limit Protection
Applications
• Mobile Phones
• PDAs
• GPS Receivers
The MIC5335 is available in fixed-output voltages.
Additional voltages are available. For more
information, contact Micrel’s Marketing department.
Data sheets and support documentation can be found
on Micrel’s web site at: www.micrel.com.
Typical Application
MicroLead Frame and MLF are registered trademarks of Amkor Technologies. ULDO is a trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
January 2007
M9999-010407
(408) 955-1690
Micrel, Inc.
MIC5335
MIC5335 Block Diagram
January 2007
2
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Ordering Information
Part number
Manufacturing
Part Number
Marking*
Voltage**
Junction
Temp. Range
Package
MIC5335-1.8/1.5YMT
MIC5335-GFYMT
AGF
1.8V/1.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-1.8/1.6YMT
MIC5335-GWYMT
AGW
1.8V/1.6V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.5/1.8YMT
MIC5335-JGYMT
AJG
2.5V/1.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.5/2.5YMT
MIC5335-JJYMT
AJJ
2.5V/2.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.6/1.85YMT
MIC5335-KDYMT
AKD
2.6V/1.85
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.6/1.8YMT
MIC5335-KGYMT
AKG
2.6V/1.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.7/2.7YMT
MIC5335-LLYMT
ALL
2.7V/2.7V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.8/1.5YMT
MIC5335-MFYMT
AMF
2.8V/1.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.8/1.8YMT
MIC5335-MGYMT
AMG
2.8V/1.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.8/2.6YMT
MIC5335-MKYMT
AMK
2.8V/2.6V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.8/2.8YMT
MIC5335-MMYMT
AMM
2.8V/2.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF
MIC5335-2.8/2.85YMT
MIC5335-MNYMT
AMN
2.8V/2.85V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.85/1.85YMT
MIC5335-NDYMT
AND
2.85V/1.85V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.85/2.6YMT
MIC5335-NKYMT
ANK
2.85V/2.6V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.85/2.85YMT
MIC5335-NNYMT
ANN
2.85V/2.85V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.9/1.5YMT
MIC5335-OFYMT
AOF
2.9V/1.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.9/1.8YMT
MIC5335-OGYMT
AOG
2.9V/1.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-2.9/2.9YMT
MIC5335-OOYMT
AOO
2.9V/2.9V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.0/1.8YMT
MIC5335-PGYMT
APG
3.0V/1.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.0/2.5YMT
MIC5335-PJYMT
APJ
3.0V/2.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.0/2.6YMT
MIC5335-PKYMT
APK
3.0V/2.6V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.0/2.8YMT
MIC5335-PMYMT
APM
3.0V/2.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.0/2.85YMT
MIC5335-PNYMT
APN
3.0V/2.85V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.0/3.0YMT
MIC5335-PPYMT
APP
3.0V/3.0V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/1.5YMT
MIC5335-SFYMT
ASF
3.3V/1.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/1.8YMT
MIC5335-SGYMT
ASG
3.3V/1.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/2.5YMT
MIC5335-SJYMT
ASJ
3.3V/2.5V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/2.6YMT
MIC5335-SKYMT
ASK
3.3V/2.6V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/2.7YMT
MIC5335-SLYMT
ASL
3.3V/2.7V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/2.8YMT
MIC5335-SMYMT
ASM
3.3V/2.8V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/2.85YMT
MIC5335-SNYMT
ASN
3.3V/2.85V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/2.9YMT
MIC5335-SOYMT
ASO
3.3V/2.9V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/3.0YMT
MIC5335-SPYMT
ASP
3.3V/3.0V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/3.2YMT
MIC5335-SRYMT
ASR
3.3V/3.2V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
MIC5335-3.3/3.3YMT
MIC5335-SSYMT
ASS
3.3V/3.3V
–40°C to +125°C
6-Pin 1.6x1.6 Thin MLF®
®
Note:
*
Under bar/Over bar symbol may not be to scale.
** For other voltages available. Contact Micrel Marketing for details.
January 2007
3
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Pin Configuration
6-pin 1.6mm × 1.6mm Thin MLF
Top View
®
Pin Description
Pin Number
Thin MLF-6
Pin Name
Pin Function
1
VIN
Supply Input.
2
GND
Ground
3
EN2
Enable Input (regulator 2). Active High Input. Logic High = On; Logic Low = Off;
Do not leave floating.
4
EN1
Enable Input (regulator 1). Active High Input. Logic High = On; Logic Low = Off;
Do not leave floating.
5
VOUT2
Regulator Output – LDO2
6
VOUT1
Regulator Output – LDO1
January 2007
4
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN) .....................................0V to +6V
Enable Input Voltage (VEN)...........................0V to +6V
Power Dissipation...........................Internally Limited(3)
Lead Temperature (soldering, 3sec ...................260°C
Storage Temperature (TS) ................. -65°C to +150°C
ESD Rating(4) .........................................................2kV
Supply voltage (VIN)............................... +2.3V to +5.5V
Enable Input Voltage (VEN).............................. 0V to VIN
Junction Temperature ......................... -40°C to +125°C
Junction Thermal Resistance
Thin MLF®-6 (θJA) ................................... 100°C/W
Electrical Characteristics(5)
VIN = EN1 = EN2 = VOUT + 1.0V; higher of the two regulator outputs, IOUTLDO1 = IOUTLDO2 = 100µA; COUT1 = COUT2 =
1µF;; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +125°C, unless noted.
Parameter
Output Voltage Accuracy
Conditions
Min
Typ
Max
Units
Variation from nominal VOUT
-2.0
+2.0
%
Variation from nominal VOUT; –40°C to +125°C
-3.0
+3.0
%
0.02
0.3
0.6
%/V
%/V
2.0
Line Regulation
VIN = VOUT + 1V to 5.5V; IOUT = 100µA
Load Regulation
IOUT = 100µA to 300mA
0.3
Dropout Voltage (Note 6)
IOUT = 100µA
0.1
IOUT = 100mA
25
75
mV
IOUT = 150mA
35
100
mV
IOUT = 300mA
75
200
mV
%
mV
EN1 = High; EN2 = Low; IOUT = 100µA to 300mA
90
120
µA
EN1 = Low; EN2 = High; IOUT = 100µA to 300mA
90
120
µA
EN1 = EN2 = High; IOUT1 = 300mA, IOUT2 = 300mA
150
190
µA
Ground Current in Shutdown
EN1 = EN2 = 0V
0.01
2
µA
Ripple Rejection
f = 1kHz; COUT = 1.0µF
Current Limit
VOUT = 0V
Output Voltage Noise
COUT = 1.0µF; 10Hz to 10MHz
Ground Current
65
350
550
dB
950
90
mA
µVRMS
Enable Inputs (EN1 / EN2)
Enable Input Voltage
Logic Low
0.2
Logic High
Enable Input Current
V
V
1.1
VIL ≤ 0.2V
0.01
1
µA
VIH ≥ 1.0V
0.01
1
µA
30
100
µs
Turn-on Time (See Timing Diagram)
Turn-on Time (LDO1 and 2)
COUT = 1.0µF
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any TA (ambient temperature) is PD(max) = (TJ(max) – TA) / θJA. Exceeding the maximum allowable
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF.
5. Specification for packaged product only.
6. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal VOUT. For outputs below
2.3V, the dropout voltage is the input-to-output differential with the minimum input voltage 2.3V.
January 2007
5
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Typical Characteristics
January 2007
6
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Functional Characteristics
January 2007
7
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Thermal Considerations
The MIC5335 is designed to provide 300mA of
continuous current for both outputs in a very small
package. Maximum ambient operating temperature
can be calculated based upon the output current and
the voltage drop across the part. Given that the input
voltage is 3.3V, the output voltage is 2.8V for VOUT1,
2.5V for VOUT2 and the output current = 300mA. The
actual power dissipation of the regulator circuit can be
determined using the equation:
Applications Information
Enable/Shutdown
The MIC5335 comes with dual active-high enable pins
that allow each regulator to be disabled
independently. Forcing the enable pin low disables the
regulator and sends it into a “zero” off-mode-current
state. In this state, current consumed by the regulator
goes nearly to zero. Forcing the enable pin high
enables the output voltage. The active-high enable pin
uses CMOS technology and the enable pin cannot be
left floating; a floating enable pin may cause an
indeterminate state on the output.
PD = (VIN – VOUT1) IOUT1 + (VIN – VOUT2) IOUT2+ VIN IGND
Because this device is CMOS and the ground current
is typically <100µA over the load range, the power
dissipation contributed by the ground current is < 1%
and can be ignored for this calculation.
Input Capacitor
The MIC5335 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1µF capacitor is
required from the input-to-ground to provide stability.
Low-ESR ceramic capacitors provide optimal
performance at a minimum of space. Additional highfrequency capacitors, such as small-valued NPO
dielectric-type capacitors, help filter out highfrequency noise and are good practice in any RFbased circuit.
PD = (3.3V – 2.8V) × 300mA + (3.3V – 2.5V) × 300mA
PD = 0.39W
To determine the maximum ambient operating
temperature of the package, use the junction-toambient thermal resistance of the device and the
following basic equation:
⎛ TJ(max) − TA
PD(max) = ⎜
⎜
θ JA
⎝
Output Capacitor
The MIC5335 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized
for use with low-ESR ceramic chip capacitors. High
ESR capacitors may cause high frequency oscillation.
The output capacitor can be increased, but
performance has been optimized for a 1µF ceramic
output capacitor and does not improve significantly
with larger capacitance.
TJ(max) = 125°C, the maximum junction temperature of
the die θJA thermal resistance = 100°C/W.
The table that follows shows junction-to-ambient
thermal resistance for the MIC5335 in the Thin MLF®
package.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature
performance.
X7R-type
capacitors
change
capacitance by 15% over their operating temperature
range and are the most stable type of ceramic
capacitors on the market. Z5U and Y5V dielectric
capacitors change value by as much as 50% and
60%, respectively, over their operating temperature
ranges. To use a ceramic chip capacitor with Y5V
dielectric, the value must be much higher than an X7R
ceramic capacitor to ensure the same minimum
capacitance
over
the
equivalent
operating
temperature range.
Package
6-Pin 1.6 X1.6
Thin MLF™
θJA
Recommended
Minimum
Footprint
θJC
100°C/W
2°C/W
Thermal Resistance
Substituting PD for PD(max) and solving for the ambient
operating temperature will give the maximum
operating conditions for the regulator circuit. The
junction-to-ambient thermal resistance for the
minimum footprint is 100°C/W.
No-Load Stability
Unlike many other voltage regulators, the MIC5335
will remain stable and in regulation with no load. This
is especially important in CMOS RAM keep-alive
applications.
January 2007
⎞
⎟
⎟
⎠
The maximum power dissipation must not be
exceeded for proper operation.
For example, when operating the MIC5335-MFYML at
an input voltage of 3.3V and 300mA loads at each
8
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
temperature of 86°C in a 1.6mm x 1.6mm Thin MLF®
package. For a full discussion of heat sinking and
thermal effects on voltage regulators, refer to the
“Regulator Thermals” subsection of Micrel’s Designing
with Low-Dropout Voltage Regulators handbook. This
information can be found on Micrel's website at:
output with a minimum footprint layout, the maximum
ambient operating temperature TA can be determined
as follows:
0.39W = (125°C – TA)/(100°C/W)
TA=86°C
http://www.micrel.com/_PDF/other/LDOBk_ds.pdf
Therefore, a 2.8V/2.5V application with 300mA at
each output current can accept an ambient operating
January 2007
9
M9999-010407
(408) 944-0800
Micrel, Inc.
MIC5335
Package Information
6-Pin 1.6mm x 1.6mm Thin MLF® (MT)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for
its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a
product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for
surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant
injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk
and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale.
© 2006 Micrel, Inc.
January 2007
10
M9999-010407
(408) 944-0800
Similar pages