ON MC78PC28NTRG Low noise 150 ma low drop out (ldo) linear voltage regulator Datasheet

MC78PC00 Series
Low Noise 150 mA
Low Drop Out (LDO)
Linear Voltage Regulator
The MC78PC00 are a series of CMOS linear voltage regulators with
high output voltage accuracy, low supply current, low dropout voltage,
and high Ripple Rejection. Each of these voltage regulators consists of
an internal voltage reference, an error amplifier, resistors, a current
limiting circuit and a chip enable circuit.
The dynamic Response to line and load is fast, which makes these
products ideally suited for use in hand−held communication
equipment. The MC78PC00 series are housed in the SOT−23 5 lead
package, for maximum board space saving.
http://onsemi.com
5
1
SOT−23−5
N SUFFIX
CASE 1212
MC78PC00 Features:
•
•
•
•
•
•
•
•
•
•
•
•
Ultra−Low Supply Current: typical 35 mA in ON mode with no load.
Standby Mode: typical 0.1 mA.
Low Dropout Voltage: typical 0.2 V @ IOUT = 100 mA.
High Ripple Rejection: typical 70 dB @ f = 1 kHz.
Low Temperature−Drift Coefficient of Output Voltage:
typical ±100 ppm/°C.
Excellent Line Regulation: typical 0.05%/V.
High Accuracy Output Voltage: ±2.0%.
Fast Dynamic Response to Line and Load.
Small Package: SOT−23 5 leads.
Built−in Chip Enable circuit (CE input pin).
Identical Pinout to the LP2980/1/2.
Pb−Free Packages are Available
PIN CONNECTIONS
VIN
•
2
CE
3
5 VOUT
2
3
4 N/C
4
DEVICE MARKING
(4 digits are available for device marking)
1
2
• Power source for cellular phones (GSM, CDMA, TDMA), Cordless
•
GND
1
(Top View)
MC78PC00 Applications:
Phones (PHS, DECT) and 2−way radios.
Power source for domestic appliances such as cameras, VCRs and
camcorders.
Power source for battery−powered equipment.
1
Marking
Voltage Version
K8
1.8 V
F5
2.5 V
F8
2.8 V
G0
3.0 V
G3
3.3 V
J0
3
4
5.0 V
Lot Number
Block Diagram
VIN
MC78PCxx
1
VOUT
Vref
CURRENT LIMIT
CE
© Semiconductor Components Industries, LLC, 2005
Pin #
Symbol
Description
1
VIN
2
GND
Input Pin
3
CE
Chip Enable Pin
4
N/C
No Connection
5
VOUT
Output Pin
Ground Pin
ORDERING INFORMATION
2
3
June, 2005 − Rev. 6
PIN DESCRIPTION
5
1
GND
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
Publication Order Number:
MC78PC00/D
MC78PC00 Series
MAXIMUM RATINGS
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁ
Symbol
Value
Unit
Input Voltage
Rating
VIN
9.0
V
Input Voltage
VCE
−0.3 ~VIN +0.3
V
Output Voltage
VOUT
−0.3 ~VIN +0.3
V
Power Dissipation
PD
250
mW
Operating Temperature Range
TA
−40 to +85
°C
Operating Junction Temperature
TJ
+125
°C
Maximum Junction Temperature
TJmax
+150
°C
Tstg
−55 to +125
°C
Storage Temperature Range
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS (TA = 25°C)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
Characteristic
Symbol
Min
Typ
Max
1.764
2.450
2.744
2.94
3.234
4.9
1.80
2.50
2.80
3.00
3.3
5.0
1.836
2.550
2.856
3.06
3.366
5.1
Unit
Output Voltage (VIN = VOUT + 1.0 V, IOUT = 30 mA)
MC78PC18
MC78PC25
MC78PC28
MC78PC30
MC78PC33
MC78PC50
VOUT
V
Nominal Output Current
(VIN = VOUT + 1.0 V, VOUT = VOUT(nom) − 0.1 V)
IOUT
150
−
−
mA
Load Regulation (VIN = VOUT + 1.0 V, 1.0 mA ≤ IOUT ≤ 80 mA)
DVOUT/DIOUT
−
12
40
mV
Supply Current in ON mode (VIN = VOUT + 1.0 V, IOUT = 0 mA)
ISS
−
35
70
mA
Istandby
−
0.1
1.0
mA
Ripple Rejection (f = 1.0 kHz, Ripple 0.5 Vp−p, VIN = VOUT + 1.0 V)
RR
−
70
−
dB
Input Voltage
VIN
−
−
8.0
V
Output Voltage Temperature Coefficient
(IOUT = 30 mA, −40°C ≤ TA ≤ +85°C)
DVOUT/DT
−
±100
−
ppm/°C
Short Circuit Current Limit (VOUT = 0 V)
Ilim
−
50
−
mA
CE Pull−down Resistance
RPD
2.5
5.0
10
MW
CE Input Voltage “H” (ON Mode)
VIH
1.5
−
VIN
V
CE Input Voltage “L” (OFF Mode)
VIL
0
−
0.25
V
Output Noise Voltage (f = 10 Hz to 100 kHz)
en
−
30
−
mVrms
Min
Typ
Max
Unit
−
−
−
−
−
0.60
0.35
0.24
0.20
0.17
1.40
0.70
0.35
0.30
0.26
−
0.05
0.20
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
Supply Current in OFF mode, i.e. VCE = GND
(VIN = VOUT + 1.0 V, IOUT = 0 mA)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE VOUT (TA = 25°C)
Characteristic
Symbol
Dropout Voltage (IOUT = 100 mA)
1.8 ≤ VOUT ≤ 1.9
2.0 ≤ VOUT ≤ 2.4
2.5 ≤ VOUT ≤ 2.7
2.8 ≤ VOUT ≤ 3.3
3.4 ≤ VOUT ≤ 6.0
VDIF
V
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
DVOUT/DVIN
Line Regulation
(VOUT + 0.5 V ≤ VIN ≤ 8.0 V, IOUT = 30 mA)
http://onsemi.com
2
%/V
MC78PC00 Series
OPERATION
MC78PC00
VIN
1
5
VOUT
ERROR AMP.
R1
Vref
CURRENT LIMIT
3
R2
2
CE
GND
In the MC78PC00, the output voltage VOUT is detected by R1, R2. The detected output voltage is then compared to the
internal voltage reference by the error amplifier. Both a current limiting circuit for short circuit protection, and a chip enable
circuit are included.
http://onsemi.com
3
MC78PC00 Series
TEST CIRCUITS
3
IN
1
VIN
0.1 mF
CE
MC78PCxx
Series
2
3
OUT
5
VOUT
IN
IOUT
0.1 mF
Figure 1. Standard Test Circuits
3
IN
1
VIN
3
OUT
5
VOUT
IN
GND
1
VIN
IOUT
P.G.
2
2
OUT
5
VOUT
IOUT
2.2 mF
GND
Figure 2. Supply Current Test Circuit
CE
MC78PCxx
Series
MC78PCxx
Series
VIN
ISS
2.2 mF
GND
1
CE
1 mF
10 mF
CE
MC78PCxx
Series
2
GND
OUT
5
VOUT
10 mF
I1
Figure 3. Ripple Rejection, Line
Transient Response Test Circuit
Figure 4. Load Transient Response
Test Circuit
http://onsemi.com
4
I2
MC78PC00 Series
3.5
1.8
VOUT, OUTPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
2.0
3.8 V
1.6
2.8 V
1.4
1.2
2.3 V
1.0
0.8
0.6
VIN = 2.1 V
0.4
TA = 25°C
0.2
0
100
3.5 V
2.0
VIN = 3.3 V
1.5
1.0
0.5
TA = 25°C
200
300
400
500
0
100
200
300
400
500
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 5. MC78PC18 Output Voltage versus
Output Current
Figure 6. MC78PC30 Output Voltage versus
Output Current
4.5
6.0
6.0 V
4.0
3.5
VOUT, OUTPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
4.0 V
2.5
0
0
5.0 V
3.0
4.5 V
2.5
VIN = 4.3 V
2.0
1.5
1.0
TA = 25°C
0.5
0
7.0 V
5.0
6.0 V
4.0
3.0
VIN = 5.3 V
5.5 V
2.0
1.0
TA = 25°C
0
100
0
200
300
400
100
0
500
200
300
400
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 7. MC78PC40 (4.0 V) Output Voltage
versus Output Current
Figure 8. MC78PC50 Output Voltage versus
Output Current
2.0
500
3.1
1.9
VOUT, OUTPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
5.0 V
3.0
IOUT = 1 mA
1.8
1.7
1.6
1.5
1.4
30 mA
1.3
TA = 25°C
50 mA
1.2
3.0
2.9
2.8
1.0 mA
2.7
30 mA
2.6
IOUT = 50 mA
TA = 25°C
2.5
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
2.0
3.0
4.0
5.0
6.0
7.0
VIN, INPUT VOLTAGE (VOLTS)
VIN, INPUT VOLTAGE (VOLTS)
Figure 9. MC78PC18 Output Voltage versus
Input Voltage
Figure 10. MC78PC30 Output Voltage versus
Input Voltage
http://onsemi.com
5
8.0
MC78PC00 Series
5.5
VOUT, OUTPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
4.5
4.0
3.5
IOUT =
1.0 mA
3.0
30 mA
50
mA
2.5
2.0
3.0
TA = 25°C
4.0
IOUT = 1.0 mA
3.5
3.0
50 mA
4.0
5.0
6.0
7.0
2.0
8.0
TA = 25°C
30 mA
3.0
4.0
5.0
6.0
7.0
8.0
VIN, INPUT VOLTAGE (VOLTS)
VIN, INPUT VOLTAGE (VOLTS)
Figure 11. MC78PC40 (4.0 V) Output Voltage
versus Input Voltage
Figure 12. MC78PC50 Output Voltage versus
Input Voltage
0.40
TA = 85°C
VDIF, DROPOUT VOLTAGE (VOLTS)
VDIF, DROPOUT VOLTAGE (VOLTS)
4.5
2.5
1.2
1.0
0.8
0.6
25°C
0.4
−40°C
0.2
0
TA = 85°C
0.35
0.30
25°C
0.25
−40°C
0.20
0.15
0.10
0.05
0
0
50
100
0
150
50
100
150
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 13. MC78PC18 Dropout Voltage versus
Output Current
Figure 14. MC78PC30 Dropout Voltage versus
Output Current
0.40
0.40
0.35
VDIF, DROPOUT VOLTAGE (VOLTS)
VDIF, DROPOUT VOLTAGE (VOLTS)
5.0
TA = 85°C
0.30
25°C
0.25
0.20
−40°C
0.15
0.10
0.05
0
0.35
0.30
TA = 85°C
0.25
25°C
0.20
0.15
−40°C
0.10
0.05
0
0
50
100
150
0
50
100
150
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 15. MC78PC40 (4.0 V) Dropout Voltage
versus Output Current
Figure 16. MC78PC50 Dropout Voltage versus
Output Current
http://onsemi.com
6
MC78PC00 Series
3.08
1.88
VIN = 2.8 V
IOUT = 30 mA
1.86
VOUT, OUTPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
1.90
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
−50
−25
0
25
50
75
100
3.04
3.02
3.00
2.98
2.96
2.94
2.92
2.90
−50
−25
0
25
50
75
TA, TEMPERATURE (°C)
Figure 17. MPC78PC18 Output Voltage
versus Temperature
Figure 18. MC78PC30 Output
Voltage versus Temperature
100
5.10
4.08
VOUT, OUTPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
VIN = 4.0 V
IOUT = 10 mA
3.05
TA, TEMPERATURE (°C)
4.10
VIN = 5.0 V
IOUT = 10 mA
4.06
4.04
4.02
4.00
3.98
3.96
3.94
3.92
3.90
−50
−25
0
25
50
75
100
5.08
VIN = 6.0 V
IOUT = 10 mA
5.06
5.04
5.02
5.00
4.98
4.96
4.94
4.92
4.90
−50
−25
0
25
50
75
TA, TEMPERATURE (°C)
TA, TEMPERATURE (°C)
Figure 19. MC78PC40 (4.0 V) Output
Voltage versus Temperature
Figure 20. MC78PC50 Output
Voltage versus Temperature
60
100
50
50
ISS , SUPPLY CURRENT (m A)
ISS , SUPPLY CURRENT (m A)
3.06
40
30
20
10
40
30
20
10
TA = 25°C
TA = 25°C
0
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
2.0
3.0
4.0
5.0
6.0
7.0
VIN, INPUT VOLTAGE (VOLTS)
VIN, INPUT VOLTAGE (VOLTS)
Figure 21. MC78PC18 Supply Current
versus Input Voltage
Figure 22. MC78PC30 Supply Current
versus Input Voltage
http://onsemi.com
7
8.0
MC78PC00 Series
50
ISS , SUPPLY CURRENT (m A)
ISS , SUPPLY CURRENT (m A)
50
40
30
20
10
40
30
20
10
TA = 25°C
TA = 25°C
0
0
3.0
4.0
5.0
6.0
7.0
8.0
2.0
4.0
5.0
6.0
7.0
VIN, INPUT VOLTAGE (VOLTS)
Figure 23. MC78PC40 (4.0 V) Supply Current
versus Input Voltage
Figure 24. MC78PC50 Supply Current
versus Input Voltage
50
50
45
45
40
35
30
25
20
−50
−25
0
25
50
75
35
30
25
−25
0
25
50
75
TA, TEMPERATURE (°C)
TA, TEMPERATURE (°C)
Figure 25. MC78PC30 Supply Current
versus Temperature
Figure 26. MC78PC40 (4.0 V) Supply
Current versus Temperature
100
0.7
VDIF, DROPOUT VOLTAGE (VOLTS)
45
40
35
30
25
20
−50
8.0
40
20
−50
100
50
ISS , SUPPLY CURRENT (m A)
3.0
VIN, INPUT VOLTAGE (VOLTS)
ISS , SUPPLY CURRENT (m A)
ISS , SUPPLY CURRENT (m A)
2.0
−25
0
25
50
75
IOUT = 150 mA
0.6
0.5
TA = 25°C
0.4 100 mA
0.3
0.2
50 mA
0 10 mA
2.0
100
30 mA
0.1
3.0
4.0
5.0
TA, TEMPERATURE (°C)
VOUT, OUTPUT VOLTAGE (VOLTS)
Figure 27. MC78PC50 Supply Current
versus Temperature
Figure 28. Dropout Voltage versus
Output Voltage
http://onsemi.com
8
6.0
80
80
70
70
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
MC78PC00 Series
60
50
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 2.8 VDC + 0.5 Vp−p
COUT = 1.0 mF
10
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 2.8 VDC + 0.5 Vp−p
COUT = 1.0 mF
0
0.1
1.0
10
100
0.1
10
100
f, FREQUENCY (kHz)
Figure 29. MC78PC18 Ripple Rejection
versus Frequency
Figure 30. MC78PC18 Ripple Rejection
versus Frequency
80
80
70
70
60
50
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 4.0 VDC + 0.5 Vp−p
COUT = 4.7 mF
10
1.0
f, FREQUENCY (kHz)
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
50
10
0
60
50
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 4.0 VDC + 0.5 Vp−p
COUT = 10 mF
10
0
0
0.1
1.0
10
0.1
100
10
100
f, FREQUENCY (kHz)
Figure 31. MC78PC30 Ripple Rejection
versus Frequency
Figure 32. MC78PC30 Ripple Rejection
versus Frequency
80
80
70
70
60
50
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 5.0 VDC + 0.5 Vp−p
COUT = 4.7 mF
10
1.0
f, FREQUENCY (kHz)
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
60
60
50
40
30
VIN = 5.0 VDC + 0.5 Vp−p
COUT = 10 mF
10
0
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
0
0.1
1.0
10
100
0.1
1.0
10
f, FREQUENCY (kHz)
f, FREQUENCY (kHz)
Figure 33. MC78PC40 (4.0 V) Ripple
Rejection versus Frequency
Figure 34. MC78PC40 (4.0 V) Ripple
Rejection versus Frequency
http://onsemi.com
9
100
MC78PC00 Series
RR, RIPPLE REJECTION (dB)
80
70
60
50
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 6.0 VDC + 0.5 Vp−p
COUT = 4.7 mF
10
0
0.1
1.0
10
100
f, FREQUENCY (kHz)
80
80
70
70
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
Figure 35. MC78PC50 Ripple Rejection
versus Frequency
60
50
40
30
IOUT = 1.0 mA
IOUT = 30 mA
IOUT = 50 mA
20
VIN = 6.0 VDC + 0.5 Vp−p
COUT = 10 mF
10
60
50
40
30
f = 400 Hz
f = 1.0 kHz
f = 10 kHz
20
10
0
0
0.1
1.0
10
100
3.1
3.2
3.3
3.4
3.5
f, FREQUENCY (kHz)
VIN, INPUT VOLTAGE (VOLTS)
Figure 36. MC78PC50 Ripple Rejection
versus Frequency
Figure 37. MC78PC30 Ripple Rejection
versus Input Voltage (DC Bias)
80
80
IOUT = 10 mA
COUT = 10 mF
70
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
IOUT = 1.0 mA
COUT = 10 mF
60
50
40
30
f = 400 Hz
f = 1.0 kHz
f = 10 kHz
20
10
IOUT = 50 mA
COUT = 10 mF
70
60
50
40
30
f = 400 Hz
f = 1.0 kHz
f = 10 kHz
20
10
0
0
3.1
3.2
3.3
3.4
3.1
3.5
3.2
3.3
3.4
VIN, INPUT VOLTAGE (VOLTS)
VIN, INPUT VOLTAGE (VOLTS)
Figure 38. MC78PC30 Ripple Rejection
versus Input Voltage (DC Bias)
Figure 39. MC78PC30 Ripple Rejection
versus Input Voltage (DC Bias)
http://onsemi.com
10
3.5
MC78PC00 Series
5.0
INPUT VOLTAGE
4.0
3.2
3.1
3.0
OUTPUT VOLTAGE
3.0
2.0
tr = tf = 5.0 ms
COUT = 4.7 mF (TANTALUM)
IOUT = 30 mA
2.9
2.8
20
40
60
80
100
3.3
5.0
INPUT VOLTAGE
4.0
3.2
3.1
3.0
OUTPUT VOLTAGE
3.0
2.0
tr = tf = 5.0 ms
COUT = 6.8 mF (TANTALUM)
IOUT = 30 mA
2.9
0
120
2.8
20
0
40
60
80
100
1.0
0
120
t, TIME (ms)
t, TIME (ms)
Figure 40. MC78PC30 Line Transient Response
Figure 41. MC78PC30 Line Transient Response
3.3
5.0
INPUT VOLTAGE
3.2
4.0
3.1
3.0
OUTPUT VOLTAGE
3.0
2.0
tr = tf = 5.0 ms
COUT = 10 mF (TANTALUM)
IOUT = 30 mA
2.9
2.8
0
20
40
60
80
100
3.4
1.0
0
150
VOUT, OUTPUT VOLTAGE (VOLTS)
6.0
3.3
100
OUTPUT CURRENT
3.2
50
3.1
0
OUTPUT VOLTAGE −50
3.0
CIN = 1.0 mf (TANTALUM)
COUT = 4.7 mF (TANTALUM)
VIN = 4.0 V
2.9
−100
−150
2.8
120
0
2.0
4.0
6.0
8.0
10
12
14
16
18
20
t, TIME (ms)
t, TIME (ms)
Figure 42. MC78PC30 Line Transient Response
Figure 43. MC78PC30 Load Transient Response
3.2
50
3.1
0
OUTPUT VOLTAGE −50
3.0
CIN = 1.0 mf (TANTALUM)
COUT = 6.8 mF (TANTALUM)
VIN = 4.0 V
2.9
−100
−150
2.8
0
2.0
4.0
6.0
8.0
10
12
14
16
18
20
150
3.3
100
OUTPUT CURRENT
3.2
50
3.1
0
OUTPUT VOLTAGE −50
3.0
CIN = 1.0 mf (TANTALUM)
COUT = 10 mF (TANTALUM)
VIN = 4.0 V
2.9
−100
−150
2.8
0
2.0
4.0
6.0
8.0
10
12
14
16
18
20
t, TIME (ms)
t, TIME (ms)
Figure 44. MC78PC30 Load Transient Response
Figure 45. MC78PC30 Load Transient Response
http://onsemi.com
11
IOUT, OUTPUT CURRENT (mA)
100
OUTPUT CURRENT
IOUT, OUTPUT CURRENT (mA)
3.3
3.4
VOUT, OUTPUT VOLTAGE (VOLTS)
150
VOUT, OUTPUT VOLTAGE (VOLTS)
3.4
IOUT, OUTPUT CURRENT (mA)
3.4
V IN, INPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
0
1.0
6.0
V IN, INPUT VOLTAGE (VOLTS)
3.3
3.4
VOUT, OUTPUT VOLTAGE (VOLTS)
6.0
V IN, INPUT VOLTAGE (VOLTS)
VOUT, OUTPUT VOLTAGE (VOLTS)
3.4
MC78PC00 Series
APPLICATION HINTS
When using these circuits, please be sure to observe the
following points:
• Phase compensation is made for securing stable operation
even if the load current varies. For this reason, be sure to
use a capacitor COUT with good frequency characteristics
and ESR (Equivalent Series Resistance) as described in
the graphs on page 11.
On page 11, the relations between IOUT (Output Current)
3
and ESR of Output Capacitor are shown. The conditions
where the white noise level is under 40 mV (Avg.) are
marked by the shaded area in the graph. (note: When
additional ceramic capacitors are connected to the Output
Pin with Output capacitor for phase compensation, there
is a possibility that the operation will be unstable. Because
of this, test these circuits with as same external
components as ones to be used on the PCB).
CE
5
1
VIN
VOUT
CERAMIC
CAPACITOR
1.0 mF
4.0 V
2
S.A.
CERAMIC
CAPACITOR
GND
ESR
SPECTRUM
ANALYSER
IOUT
MEASURING CONDITIONS: (1) FREQUENCY RANGE: 10 Hz TO 1.0 MHz
MEASURING CONDITIONS: (2) TEMPERATURE: 25°C
Figure 46. Measuring Circuit for White Noise: MC78PC30
• Set external components, especially the Output Capacitor,
as close as possible to the circuit, and make the wiring as
short as possible.
• Please be sure the Vin and GND lines are sufficiently
wide. When the impedance of these lines is high, there is
a chance to pick up noise or to malfunction.
• Connect the capacitor with a capacitance of 1.0 mF or
more between Vin and GND as close as possible to Vin or
GND.
CE
IN
VIN
MC78PCxx
+
CAP.
OUT
VOUT
+
GND
CAP.
Figure 47. Typical Application
http://onsemi.com
12
MC78PC00 Series
10
10
ESR (W )
100
ESR (W )
100
1.0
1.0
0.1
0.1
50
100
150
50
0
100
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 48. Ceramic Capacitor 4.7 mF
Figure 49. Ceramic Capacitor 6.8 mF
100
10
ESR (W )
0
1.0
0.1
0
50
100
IOUT, OUTPUT CURRENT (mA)
Figure 50. Ceramic Capacitor 10 mF
http://onsemi.com
13
150
150
MC78PC00 Series
TAPE AND REEL INFORMATION
Component Taping Orientation for 5L SOT−23 Devices
USER DIRECTION OF FEED
DEVICE
MARKING
PIN 1
Standard Reel Component Orientation
for TR Suffix Device
(Mark Right Side Up)
Tape & Reel Specifications Table
Package
5L SOT−23
Tape Width (W)
8 mm
Pitch (P)
Part Per Full Reel
4 mm
3000
Reel Diameter
7 inches
ORDERING INFORMATION
Device
Package
MC78PC18NTR
SOT−23 5 Leads
MC78PC18NTRG
SOT−23 5 Leads
(Pb−Free)
MC78PC25NTR
SOT−23 5 Leads
MC78PC25NTRG
SOT−23 5 Leads
(Pb−Free)
MC78PC28NTR
SOT−23 5 Leads
MC78PC28NTRG
SOT−23 5 Leads
(Pb−Free)
MC78PC30NTR
SOT−23 5 Leads
MC78PC30NTRG
SOT−23 5 Leads
(Pb−Free)
MC78PC33NTR
SOT−23 5 Leads
MC78PC33NTRG
SOT−23 5 Leads
(Pb−Free)
MC78PC50NTR
SOT−23 5 Leads
MC78PC50NTRG
SOT−23 5 Leads
(Pb−Free)
Shipping †
3000 Units/Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Other voltages are available. Consult your ON Semiconductor representative.
http://onsemi.com
14
MC78PC00 Series
PACKAGE DIMENSIONS
SOT−23−5
N SUFFIX
PLASTIC PACKAGE
CASE 1212−01
ISSUE O
A
5
E
1
A2
0.05 S
B
D
A1
4
2
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DATUM C IS A SEATING PLANE.
DIM
A1
A2
B
C
D
E
E1
e
e1
L
L1
L
3
E1
L1
B
e
e1
C
5X
0.10
M
C B
S
A
C
S
SOLDERING FOOTPRINT*
0.7 MAX.
1.0
2.4
0.95
0.95
(Unit: mm)
1.9
Figure 51. SOT−23−5
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
15
MILLIMETERS
MIN
MAX
0.00
0.10
1.00
1.30
0.30
0.50
0.10
0.25
2.80
3.00
2.50
3.10
1.50
1.80
0.95 BSC
1.90 BSC
0.20
−−−
0.45
0.75
MC78PC00 Series
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
16
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC78PC00/D
Similar pages