Document 284-1 SMT Power Inductors - DO5010H Series • Irms ratings up to 15 A; saturation currents up to 30 A • Heavy gauge wire for low DC resistance Designer’s Kit C355 contains 3 of each part Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant tin-silver over copper. Other terminations available at additional cost. Weight 3.2 – 4.0 g Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 250 per 13″ reel Plastic tape: 32 mm wide, 0.38 mm thick, 24 mm pocket spacing, 7.8 mm pocket depth PCB washing Only pure water or alcohol recommended DCR SRF Inductance2 max typ3 Part Number1 ±20% (µH) (mOhm) (MHz) DO5010H-781ML_ 0.78 2.6 156 DO5010H-152ML_ 1.5 4.0 100 DO5010H-222ML_ 2.2 6.1 75 DO5010H-332ML_ 3.3 8.6 60 DO5010H-392ML_ 3.9 10 55 DO5010H-472ML_ 4.7 14 40 DO5010H-602ML_ 6.0 17 35 DO5010H-782ML_ 7.8 18 35 DO5010H-103ML_ 10 26 28 DO5010H-123ML_ 12 28 26 DO5010H-153ML_ 15 32 20 DO5010H-223ML_ 22 47 20 DO5010H-333ML_ 33 66 15 DO5010H-473ML_ 47 86 9 DO5010H-683ML_ 68 130 8 DO5010H-104ML_ 100 190 7 DO5010H-154ML_ 150 250 6 DO5010H-224ML_ 220 380 5 DO5010H-334ML_ 330 560 4 DO5010H-474ML_ 470 850 3 DO5010H-684ML_ 680 1100 2.5 DO5010H-105ML_ 1000 1800 2.0 Isat4 (A) 30 25 20 17 15 13 12 11 10 8.5 8.0 7.0 5.5 4.5 3.5 3.0 2.6 2.4 1.9 1.4 1.2 1.0 Irms5 (A) 15 15 12 10 9.0 8.4 7.5 7.5 6.0 5.2 4.4 3.5 3.0 2.6 2.3 1.8 1.5 1.2 1.0 0.82 0.72 0.56 1. When ordering, please specify termination and packaging codes: DO5010H-105MLD = RoHS compliant tin-silver over copper. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape. B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4284A LCR meter or equivalent. 3. SRF measured using Agilent/HP 8753D network analyzer. 4. DC current at which the inductance drops 10% (typ) from its value without current. 5. Current that causes a 40°C temperature rise from 25°C ambient. 6. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Termination: L Document 284-1 Revised 10/14/08 Document 284-2 SMT Power Inductors - DO5010H Series Typical L vs Frequency Typical L vs Current 10000 10000 1000 µH 100 µH 100 10 µH 10 100 µH 100 10 µH 10 0.78 µH 1 0.78 µH 1 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 0.1 0.1 0.01 1 0.1 10 Frequency (MHz) 0.1 1 Current (A) 0.500 12,70 Irms Derating 120 Note: Maximum height: 0.315 for -781 to -153 8,00 0.300 for -223 to -683 7,62 0.280 for -104 to -105 7,11 Note 110 0.730 max 18,54 90 0.561 min 14,25 80 0.075 1,90 70 60 0.250 6,35 0.600 max 15,24 50 40 25°C Percent of rated Irms 100 100 10 30 0.065 max 1,65 20 0.200 max 5,08 0.710 max 18,03 10 0 -40 -20 0 20 40 60 80 100 Internal code 120 140 0.626 15,90 Recommended Land Pattern Dash number Ambient temperature (°C) XXX X Part Marking Part marking since Feb. 2005. Parts manufactured prior to that date may have color dots. Visit www.coilcraft.com/colrpowr.cfm for color dot marking details. Dimensions are in inches mm Document 284-2 Revised 10/14/08