Document 548-1 Shielded Power Inductors – LPS4414 • Very low DCR; excellent current handling • 4.4 × 4.4 mm footprint; only 1.4 mm tall Designer’s Kit C340 contains 3 of each values Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 82.3 – 89.8 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.52 mm pocket depth Recommended pick and place nozzle: OD: 4.5 mm; ID: ≤ 2 mm PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. Isat (A)5 Irms (A)6 DCR SRF Inductance2 max3 typ4 10% 20% 30% 20°C 40°C Part number1 ±20% (µH) (Ohms) (MHz) drop drop drop rise rise LPS4414-301ML_ LPS4414-501ML_ LPS4414-701ML_ LPS4414-102ML_ LPS4414-152ML_ LPS4414-182ML_ LPS4414-222ML_ LPS4414-332ML_ LPS4414-472ML_ LPS4414-562ML_ LPS4414-682ML_ LPS4414-822ML_ LPS4414-103ML_ LPS4414-123ML_ LPS4414-153ML_ LPS4414-183ML_ LPS4414-223ML_ LPS4414-333ML_ LPS4414-473ML_ LPS4414-563ML_ LPS4414-683ML_ LPS4414-104ML_ LPS4414-124ML_ LPS4414-154ML_ LPS4414-224ML_ LPS4414-334ML_ LPS4414-474ML_ LPS4414-564ML_ LPS4414-684ML_ LPS4414-824ML_ LPS4414-105ML_ LPS4414-155ML_ LPS4414-185ML_ LPS4414-225ML_ LPS4414-335ML_ 0.30 0.50 0.70 1.0 1.5 1.8 2.2 3.3 4.7 5.6 6.8 8.2 10 12 15 18 22 33 47 56 68 100 120 150 220 330 470 560 680 820 1000 1500 1800 2200 3300 0.040 0.050 0.055 0.060 0.078 0.087 0.110 0.165 0.215 0.260 0.270 0.350 0.380 0.380 0.440 0.530 0.590 0.715 0.935 1.15 1.35 1.90 2.60 3.10 4.10 6.00 9.50 10.7 11.7 15.1 16.3 26.4 35.0 42.5 56.0 470 330 225 190 150 130 115 85.0 68.0 58.0 54.0 50.0 43.0 38.0 36.0 31.0 27.0 23.0 18.0 16.0 14.6 11.0 10.0 9.0 6.7 5.6 4.3 4.0 3.5 3.0 2.6 2.2 1.9 1.9 1.3 5.6 4.3 3.7 3.0 2.9 2.7 2.2 1.8 1.4 1.4 1.2 1.1 1.1 0.94 0.85 0.76 0.69 0.47 0.39 0.37 0.32 0.26 0.23 0.22 0.18 0.14 0.13 0.12 0.10 0.10 0.10 0.096 0.089 0.082 0.072 5.7 4.4 3.75 3.1 3.1 2.8 2.3 1.9 1.5 1.4 1.3 1.3 1.2 0.97 0.89 0.80 0.72 0.49 0.42 0.39 0.33 0.28 0.24 0.23 0.20 0.16 0.14 0.13 0.11 0.105 0.102 0.099 0.094 0.089 0.078 5.8 4.5 3.8 3.2 3.2 2.9 2.35 1.95 1.55 1.5 1.4 1.3 1.3 1.0 0.92 0.82 0.74 0.51 0.43 0.40 0.34 0.285 0.25 0.24 0.20 0.165 0.145 0.14 0.12 0.11 0.106 0.100 0.097 0.092 0.083 2.35 2.10 1.85 1.75 1.55 1.50 1.25 1.15 0.90 0.75 0.70 0.70 0.70 0.66 0.63 0.56 0.53 0.49 0.44 0.42 0.36 0.31 0.27 0.24 0.22 0.17 0.14 0.13 0.13 0.11 0.10 0.085 0.075 0.065 0.055 3.25 2.80 2.50 2.30 2.00 1.90 1.60 1.50 1.20 1.10 1.00 0.98 0.95 0.88 0.82 0.75 0.68 0.65 0.58 0.54 0.48 0.40 0.34 0.32 0.29 0.23 0.23 0.17 0.17 0.14 0.13 0.11 0.10 0.080 0.070 1. Please specify termination and packaging codes: LPS4414-223MLC Termination: L = RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 8753ES or equivalent. 5. DC current at which the inductance drops the specified amount from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 548-1 Revised 11/21/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 548-2 Shielded Power Inductors – LPS4414 Series Typical L vs Current Typical L vs Frequency 10000 10000 3300 µH 3300 µH 330 µH 100 100 µH 33 µH 10 10 µH 3.3 µH 1 0.1 0.1 Current (A) 1 330 µH 100 µH 100 33 µH 10 µH 10 3.3 µH 1 µH 1 1 µH 0.01 1000 µH 1000 1000 µH Inductance (µH) Inductance (µH) 1000 10 Current Derating 0.1 0.01 1 0.1 10 Frequency (MHz) 0.169 ±0.004 4,30 ±0,10 0.169 ±0.004 4,30 ±0,10 100 XXX X 90 80 70 Dash number 60 0.0551 max * 1,40 40 30 20 10 0 Winding direction Internal code 50 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 Recommended Land Pattern 0.128 3,25 0.059 1,50 40 60 80 100 120 140 0.030 typ 0,75 Ambient temperature (°C) 0.185 4,70 0.118 3,00 0.030 typ 0,75 * For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional 0.005 inch (0,13 mm). Dimensions are in 0.124 3,15 0.055 1,40 0.059 1,50 0.118 3,00 0.185 4,70 inches mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 548-2 Revised 11/21/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.