Fairchild MM74HC148M 8-3 line priority encoder Datasheet

Revised February 1999
MM74HC148
8-3 Line Priority Encoder
General Description
The MM74HC148 priority encoder utilizes advanced silicon-gate CMOS technology. It has the high noise immunity
and low power consumption typical of CMOS circuits, as
well as the speeds and output drive similar to LB-TTL.
This priority encoder accepts 8 input request lines 0–7 and
outputs 3 lines A0–A2. The priority encoding ensures that
only the highest order data line is encoded. Cascading circuitry (enable input EI and enable output EO) has been
provided to allow octal expansion without the need for
external circuitry. All data inputs and outputs are active at
the low logic level.
All inputs are protected from damage due to static discharge by internal diode clamps to VCC and ground.
Features
■ Typical propagation delay: 13 ns
■ Wide supply voltage range: 2V–6V
Ordering Code:
Order Number
MM74HC148M
MM74HC148MTC
MM74HC148N
Package Number
M16A
MTC16
N16E
Package Description
16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150” Narrow
16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Connection Diagram
Truth Table
Inputs
Pin Assignments for DIP, SOIC and TSSOP
Outputs
EI 0 1 2 3 4 5 6 7 A2 A1 A0 GS EO
H X X X X X X X X H
H
H
H
L H H H H H H H H H
H
H
H
H
L
L X X X X X X X L
L
L
L
L
H
L X X X X X X L H
L
L
H
L
H
L X X X X X L H H
L
H
L
L
H
L X X X X L H H H
L
H
H
L
H
L X X X L H H H H H
L
L
L
H
L X X L H H H H H H
L
H
L
H
L X L H H H H H H H
H
L
L
H
L L H H H H H H H H
H
H
L
H
H = HIGH
L = LOW
X = Irrelevant
© 1999 Fairchild Semiconductor Corporation
DS009390.prf
www.fairchildsemi.com
MM74HC148 8-3 Line Priority Encoder
October 1987
MM74HC148
Schematic Diagram
www.fairchildsemi.com
2
MM74HC148
Logic Diagram
3
www.fairchildsemi.com
MM74HC148
Absolute Maximum Ratings(Note 1)
Recommended Operation
Conditions
(Note 2)
−0.5 to +7.0V
Supply Voltage (VCC )
DC Input Voltage (VIN)
−1.5 to VCC +1.5V
DC Output Voltage (VOUT)
−0.5 to VCC +0.5V
Clamp Diode Current (IIK, IOK)
±20 mA
DC Output Current, per pin (IOUT)
±25 mA
(VIN, VOUT)
Operating Temperature Range (TA)
Power Dissipation (PD)
600 mW
S.O. Package only
500 mW
Max
Units
2
6
V
0
VCC
V
−40
+85
°C
Input Rise or Fall Times
−65°C to +150°C
(Note 3)
Min
DC Input or Output Voltage
±50 mA
DC VCC or GND Current, per pin (ICC)
Storage Temperature Range (TSTG)
Supply Voltage (VCC)
(tr, tf) VCC = 2.0V
1000
ns
VCC = 4.5V
500
ns
VCC = 6.0V
400
ns
Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur.
Lead Temperature (TL)
(Soldering 10 seconds)
260°C
Note 2: Unless otherwise specified all voltages are referenced to ground.
Note 3: Power Dissipation temperature derating—plastic “N” package: −12
mW/°C from 65°C to 85°C.
DC Electrical Characteristics
Symbol
VIH
VIL
VOH
Parameter
Conditions
(Note 4)
VCC
TA = 25°C
Typ
TA = −40 to 85°C TA = −55 to 125°C
Guaranteed Limits
Units
Minimum HIGH Level
2.0V
1.5
1.5
1.5
V
Input Voltage
4.5V
3.15
3.15
3.15
V
6.0V
4.2
4.2
4.2
V
Maximum LOW Level
2.0V
0.5
0.5
0.5
V
Input Voltage
4.5V
1.35
1.35
1.35
V
6.0V
1.8
1.8
1.8
V
Minimum HIGH Level
VIN = V IH or VIL
Output Voltage
|IOUT| ≤ 20 µA
2.0V
2.0
1.9
1.9
1.9
V
4.5V
4.5
4.4
4.4
4.4
V
6.0V
6.0
5.9
5.9
5.9
V
|IOUT| ≤ 4.0 mA
4.5V
4.7
3.96
3.84
3.7
V
|IOUT| ≤ 5.2 mA
6.0V
5.2
5.48
5.34
5.2
V
VIN = V IH or VIL
VOL
Maximum LOW Level
VIN = V IH or VIL
Output Voltage
|IOUT| ≤ 20 µA
2.0V
0
0.1
0.1
0.1
V
4.5V
0
0.1
0.1
0.1
V
6.0V
0
0.1
0.1
0.1
V
V
VIN = V IH or VIL
IIN
|IOUT| ≤ 4.0 mA
4.5V
0.2
0.26
0.33
0.4
|IOUT| ≤ 5.2 mA
6.0V
0.2
0.26
0.33
0.4
V
VIN = V CC or GND
6.0V
±0.1
±1.0
±1.0
µA
Maximum Quiescent
VIN = V CC or GND
6.0V
8.0
80
160
µA
Supply Current
IOUT = 0 µA
Maximum Input
Current
ICC
Note 4: For a power supply of 5V ±10% the worst case output voltages (VOH, and VOL) occur for HC at 4.5V. Thus the 4.5V values should be used when
designing with this supply. Worst case VIH and VIL occur at VCC = 5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current (IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0V values should be used.
www.fairchildsemi.com
4
MM74HC148
AC Electrical Characteristics
Symbol
tPHL, tPLH
Parameter
Conditions
Typ
Maximum Propagation Delay,
Guaranteed
Limits
14
Units
ns
Any Input to Any Output
AC Electrical Characteristics
VCC = 2.0V to 6.0V, CL = 50 pF, tr = tf = 6 ns (unless otherwise specified)
Symbol
Parameter
Conditions
tPHL, tPLH Inputs 0–7
2.0V
to Outputs
4.5V
A0, A1, A2
6.0V
tPHL, tPLH Inputs 0–7
4.5V
Output EO
6.0V
4.5V
Output GS
6.0V
4.5V
A0, A1, A2
6.0V
tf, tr
Cpd
17
17
2.0V
to
4.5V
Output GS
6.0V
tPHL, tPLH Input EI
15
2.0V
to Outputs
tPHL, tPLH Input EI
14
2.0V
to
tPHL, tPLH Input EI
Typ
2.0V
to
tPHL, tPLH Inputs 0–7
TA = 25°C
VCC
12
2.0V
to
4.5V
Output EO
6.0V
Maximum
2.0V
Output Rise
4.5V
and Fall Time
6.0V
12
7
Power Dissipation
TA = −40°C to +85°C TA = −55°C to +125°C
Guaranteed Limits
Units
140
175
210
28
35
42
ns
24
30
36
ns
140
175
210
ns
28
35
42
ns
24
30
36
ns
160
200
240
ns
32
40
48
ns
27
34
41
ns
160
200
240
ns
32
40
48
ns
27
34
41
ns
100
125
150
ns
20
25
30
ns
17
21
26
ns
100
125
150
ns
20
25
30
ns
17
21
26
ns
75
95
110
ns
15
19
22
ns
13
16
19
52
ns
ns
pF
Capacitance (Note 5)
Cin
Maximum Input
5
10
10
10
pF
Capacitance
Note 5: Cpd determines the no load dynamic power consumption, and the no load dynamic current consumption.
5
www.fairchildsemi.com
MM74HC148
Physical Dimensions inches (millimeters) unless otherwise noted
16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150” Narrow
Package Number M16A
www.fairchildsemi.com
6
MM74HC148
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC16
7
www.fairchildsemi.com
MM74HC148 8-3 Line Priority Encoder
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Package Number N16E
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
1. Life support devices or systems are devices or systems
device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the
sonably expected to cause the failure of the life support
body, or (b) support or sustain life, and (c) whose failure
device or system, or to affect its safety or effectiveness.
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
www.fairchildsemi.com
user.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
Similar pages