MURF2020CT THRU MURF2060CT R GLASS PASSIVATED SUPER FAST RECTIFIER Reverse Voltage - 200 -600 Volts Forward Current - 20.0Amperes S E M I C O N D U C T O R FEATURES ITO-220AB Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Fast switching for high efficiency Low forward voltage drop Single rectifier construction High surge capability For use in low voltage ,high frequency inverters, free wheeling ,and polarity protection applications JF MURF2020CT High temperature soldering guaranteed:260°C/10 seconds, 0.25"(6.35mm)from case 0.177(4.50) Component in accordance to RoHS 2011/65/EU 0.138(3.50) 0.410(10.41) 0.140(3.55) 0.390(9.91) 0.128(3.25) DIA 0.187(4.75) 0.167(4.25) 0.130(3.31) 0.111(2.81) 0.111(2.83) 0.101(2.57) 0.272(6.90) 0.256(6.50) 1 PIN 2 3 1.161(29.5) 0.110(2.80) 1.083(27.5) 0.056(1.43) 0.043(1.10) 0.102(2.60) 0.551(14.00) 0.067(1.70) 0.059(1.50) 0.512(13.00) 0.029(0.73) MECHANICAL DATA 0.019(0.47) 0.104(2.64) 0.096(2.44) Case: JEDEC ITO-220AB molded plastic body 0.029(0.73) 0.019(0.47) Terminals: Lead solderable per MIL-STD-750,method 2026 Polarity: As marked. Mounting Position: Any Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Ratings at 25°C ambient temperature unless otherwise specified ,Single phase ,half wave ,resistive or inductive load. For capacitive load,derate by 20%.) Symbols MURF 2020CT MURF 2040CT MURF 2060CT VRRM VRMS VDC 200 400 600 140 280 420 400 600 Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current(see Fig.1) Per leg Total device Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 10.0 A per leg(Note 1 ) Maximum instantaneous reverse current at rated DC blocking voltage(Note 1) T A =25°C TA =125°C Maximum Reverse Recovery Time (Note 2) Typical thermal resistance (Note 3) Operating junction temperature range Storage temperature range 200 Units Volts Volts Volts I(AV) 10.0 20.0 Amps IFSM 150.0 150 Amps VF 0.975 1.3 1.5 5 IR 250 Volts μA 35 ns RθJC 2.5 °C/W TJ TSTG -55 to+150 °C -55 to+175 °C Trr Notes: 1. Pulse test: 300μs pulse width,1% duty cycle 2. Reverse recovery test conditions IF=0.5A,IR=1.0A, Irr=0.5A 3. Thermal resistance from junction to case JINAN JINGHENG ELECTRONICS CO., LTD. 9-36 HTTP://WWW.JINGHENGGROUP.COM RATINGS AND CHARACTERISTIC CURVES MURF2020CT THRU MURF2060CT FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES FIG.1-FORWARD CURRENT DERATING CURVE 24 20 RESISTIVE OR INDUCTVE LOAD 16 12 8 4 0 0 20 40 60 80 100 120 180 150 LEAD TEMPERATURE (°C) 175 8.3ms Single Half Sine-Wave (JEDEC Method) 150 125 100 75 50 25 0 1 2 5 100 50 20 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 50 10 400V 10 TJ=100°C (uA) 200V 600V INSTANTANEOUS REVERSE CURRENT INSTANTANEOUS FORWARD CURRENT( AMPERES) 10 NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PULSE WIDTH=300μS 1% DUTY CYCLE 1 0.1 1 TJ=25°C 0.1 0.01 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.001 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE% FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/ W FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 4000 TJ=25°C f=1.0MHZ Vsig=50mVp-p 1000 100 0.1 1 10 100 REVERSE VOLTAGE. VOLTS JINAN JINGHENG ELECTRONICS CO., LTD. 100 10 1 0.1 0.01 0.1 1 10 100 T, PULSE DURATION ,sec. 9-37 HTTP://WWW.JINGHENGGROUP.COM