ETC ICS9LPR502SGLFT 56-pin ck505 w/fully integrated voltage regulator integrated series resistor Datasheet

Datasheet
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE
REGULATOR + INTEGRATED SERIES RESISTOR
Recommended Application:
Key Specifications:
CK505 compliant clock with fully integrated voltage
regulator and Internal series resistor on differential outputs,
PCIe Gen 1 compliant
•
CPU outputs cycle-cycle jitter < 85ps
•
SRC output cycle-cycle jitter < 125ps
•
PCI outputs cycle-cycle jitter < 250ps
Output Features:
•
+/- 100ppm frequency accuracy on CPU & SRC
clocks
•
2 - CPU differential low power push-pull pairs
•
7 - SRC differential low power push-pull pairs
Features/Benefits:
•
1 - CPU/SRC selectable differential low power push-pull
pair
•
•
1 - SRC/DOT selectable differential low power push-pull
pair
•
Integrated series resistors on differential outputs,
Zo=50W
•
5 - PCI, 33MHz
•
•
1 - PCI_F, 33MHz free running
Supports spread spectrum modulation, default is 0.5%
down spread
•
1 - USB, 48MHz
•
•
1 - REF, 14.318MHz
Uses external 14.318MHz crystal, external crystal
load caps are required for frequency tuning
•
One differential push-pull pair selectable between
SRC and two single-ended outputs
2
FSLC
B0b7
0
0
0
0
1
1
1
1
1
FSLB
B0b6
0
0
1
1
0
0
1
1
1
FSLA
B0b5
0
1
0
1
0
1
0
1
regulator
Pin Configuration
CPU
MHz
SRC
MHz
PCI
MHz
REF
MHz
USB
MHz
DOT
MHz
266.66
133.33
200.00
166.66
333.33
100.00
400.00
100.00
33.33
14.318
48.00
96.00
PCICLK0/CR#_A
VDDPCI
PCICLK1/CR#_B
PCICLK2/LTE
PCICLK3
PCICLK4/SRC5_EN
PCI_F5/ITP_EN
GNDPCI
VDD48
USB_48MHz/FSLA
GND48
VDD96I/O
DOTT_96/SRCCLKT0
DOTC_96/SRCCLKC0
GND
VDD
SRCCLKT1/SE1
SRCCLKC1/SE2
GND
VDDPLL3I/O
SRCCLKT2/SATACLKT
SRCCLKC2/SATACLKC
GNDSRC
SRCCLKT3/CR#_C
SRCCLKC3/CR#_D
VDDSRCI/O
SRCCLKT4
SRCCLKC4
Reserved
1. FSLA and FSLB are low-threshold inputs.Please see VIL_FS and VIH_FS specifications in
the Input/Supply/Common Output Parameters Table for correct values.
Also refer to the Test Clarification Table.
2. FSLC is a three-level input. Please see the VIL_FS and VIH_FS
specifications in the Input/Supply/Common Output Parameters Table for correct values.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
ICS 9LPRS502
Table 1: CPU Frequency Select Table
Does not require external pass transistor for voltage
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
SCLK
SDATA
FSLC/TEST_SEL/REF0
VDDREF
X1
X2
GNDREF
FSLB/TEST_MODE
CK_PWRGD/PD#
VDDCPU
CPUCLKT0
CPUCLKC0
GNDCPU
CPUCLKT1
CPUCLKC1
VDDCPUI/O
NC
CPUCLKT2_ITP/SRCCLKT8
CPUCLKC2_ITP/SRCCLKC8
VDDSRCI/O
SRCCLKT7/CR#_F
SRCCLKC7/CR#_E
GNDSRC
SRCCLKT6
SRCCLKC6
VDDSRC
PCI_STOP#/SRCCLKT5
CPU_STOP#/SRCCLKC5
56-SSOP/TSSOP
* Internal Pull-Up Resistor
** Internal Pull-Down Resistor
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
1
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
SSOP/TSSOP Pin Description
PIN #
PIN NAME
TYPE
1
PCI0/CR#_A
2
VDDPCI
3
PCI1/CR#_B
I/O
4
PCI2/TME
I/O
5
PCI3
6
PCI4/SRC5_EN
I/O
PWR
OUT
I/O
I/O
DESCRIPTION
3.3V PCI clock output or Clock Request control A for either SRC0 or SRC2 pair
The power-up default is PCI0 output, but this pin may also be used as a Clock Request control of
SRC pair 0 or SRC pair 2 via SMBus. Before configuring this pin as a Clock Request Pin, the PCI
output must first be disabled in byte 2, bit 0 of SMBus address space . After the PCI output is
disabled (high-Z), the pin can then be set to serve as a Clock Request pin for either SRC pair 2 or
pair 0 using the CR#_A_EN bit located in byte 5 of SMBUs address space.
Byte 5, bit 7
0 = PCI0 enabled (default)
1= CR#_A enabled. Byte 5, bit 6 controls whether CR#_A controls SRC0 or SRC2 pair
Byte 5, bit 6
0 = CR#_A controls SRC0 pair (default),
1= CR#_A controls SRC2 pair
Power supply pin for the PCI outputs, 3.3V nominal
3.3V PCI clock output/Clock Request control B for either SRC1 or SRC4 pair
The power-up default is PCI1 output, but this pin may also be used as a Clock Request control of
SRC pair 1 or SRC pair 4 via SMBus. Before configuring this pin as a Clock Request Pin, the PCI
output must first be disabled in byte 2, bit 1 of SMBus address space . After the PCI output is
disabled (high-Z), the pin can then be set to serve as a Clock Request pin for either SRC pair 1 or
pair 4 using the CR#_B_EN bit located in byte 5 of SMBUs address space.
Byte 5, bit 5
0 = PCI1 enabled (default)
1= CR#_B enabled. Byte 5, bit 6 controls whether CR#_B controls SRC1 or SRC4 pair
Byte 5, bit 4
0 = CR#_B controls SRC1 pair (default)
1= CR#_B controls SRC4 pair
3.3V PCI clock output / Trusted Mode Enable (TME) Latched Input. This pin is sampled on powerup as follows
0 = Overclocking of CPU and SRC Allowed
1 = Overclocking of CPU and SRC NOT allowed
After being sampled on power-up, this pin becomes a 3.3V PCI Output
3.3V PCI clock output.
3.3V PCI clock output / SRC5 pair or PCI_STOP#/CPU_STOP# enable strap. On powerup, the
logic value on this pin determines if the SRC5 pair is enabled or if CPU_STOP#/PCI_STOP# is
enabled (pins 29 and 30). The latched value controls the pin function on pins 29 and 30 as follows
0 = PCI_STOP#/CPU_STOP#
1 = SRC5/SRC5#
Free running PCI clock output and ITP/SRC8 enable strap. This output is not affected by the state
of the PCI_STOP# pin. On powerup, the state of this pin determines whether pins 38 and 39 are an
ITP or SRC pair.
0 =SRC8/SRC8#
1 = ITP/ITP#
Ground for PCI clocks.
7
PCI_F5/ITP_EN
8
GNDPCI
PWR
9
VDD48
PWR
10
USB_48MHz/FSLA
11
GND48
PWR
12
VDD96_IO
PWR
13
DOTT_96/SRCT0
OUT
14
DOTC_96/SRCC0
OUT
15
GND
PWR
Power supply for DOT96 output. 1.05 to 3.3V +/-5%.
True clock of SRC or DOT96. The power-up default function is SRC0. After powerup, this pin
function may be changed to DOT96 via SMBus Byte 1, bit 7 as follows:
0= SRC0
1=DOT96
Complement clock of SRC or DOT96. The power-up default function is SRC0#. After powerup, this
pin function may be changed to DOT96# via SMBus Byte 1, bit 7 as follows
0= SRC0#
1=DOT96#
Ground pin for the DOT96 clocks.
16
VDD
PWR
Power supply for SRC / SE1 and SE2 clocks, 3.3V nominal.
I/O
Power supply for USB clock, nominal 3.3V.
Fixed 48MHz USB clock output. 3.3V./ 3.3V tolerant input for CPU frequency selection. Refer to
input electrical characteristics for Vil_FS and Vih_FS values.
Ground pin for the 48MHz outputs.
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
2
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
SSOP/TSSOP Pin Description (continued)
PIN #
PIN NAME
TYPE
DESCRIPTION
17
SRCT1/SE1
OUT
True clock of differential SRC1 clock pair / 3.3V single-ended output. The powerup default is 100
MHz SRC, -0.5% downspread. The pin function may be changed via SMBus B1b[4:1]
18
SRCC1/SE2
OUT
Complement clock of differential SRC1 clock pair / 3.3V single-ended output. The powerup default
is 100 MHz SRC, -0.5% downspread. The pin function may be changed via SMBus B1b[4:1]
19
GND
PWR
Ground pin for SRC / SE1 and SE2 clocks, PLL3.
20
VDDPLL3_IO
PWR
Power supply for PLL3 output. 1.05 to 3.3V +/-5%.
21
SRCT2/SATAT
OUT
True clock of differential SRC/SATA clock pair.
22
SRCC2/SATAC
OUT
Complement clock of differential SRC/SATA clock pair.
23
GNDSRC
PWR
Ground pin for SRC clocks.
24
25
SRCT3/CR#_C
SRCC3/CR#_D
I/O
I/O
PWR
True clock of differential SRC clock pair/ Clock Request control C for either SRC0 or SRC2 pair
The power-up default is SRCCLK3 output, but this pin may also be used as a Clock Request
control of SRC pair 0 or SRC pair 2 via SMBus. Before configuring this pin as a Clock Request Pin,
the SRC3 output must first be disabled in byte 4, bit 7 of SMBus address space . After the SRC3
output is disabled, the pin can then be set to serve as a Clock Request pin for either SRC pair 2 or
pair 0 using the CR#_C_EN bit located in byte 5 of SMBUs address space.
Byte 5, bit 3
0 = SRC3 enabled (default)
1= CR#_C enabled. Byte 5, bit 2 controls whether CR#_C controls SRC0 or SRC2 pair
Byte 5, bit 2
0 = CR#_C controls SRC0 pair (default),
1= CR#_C controls SRC2 pair
Complementary clock of differential SRC clock pair/ Clock Request control D for either SRC1 or
SRC4 pair
The power-up default is SRCCLK3 output, but this pin may also be used as a Clock Request
control of SRC pair 1 or SRC pair 4 via SMBus. Before configuring this pin as a Clock Request Pin,
the SRC3 output must first be disabled in byte 4, bit 7 of SMBus address space . After the SRC3
output is disabled, the pin can then be set to serve as a Clock Request pin for either SRC pair 1 or
pair 4 using the CR#_D_EN bit located in byte 5 of SMBUs address space.
Byte 5, bit 1
0 = SRC3 enabled (default)
1= CR#_D enabled. Byte 5, bit 0 controls whether CR#_D controls SRC1 or SRC4 pair
Byte 5, bit 0
0 = CR#_D controls SRC1 pair (default),
1= CR#_D controls SRC4 pair
Power supply for SRC clocks. 1.05 to 3.3V +/-5%.
26
VDDSRC_IO
27
SRCT4
I/O
True clock of differential SRC clock pair 4
28
SRCC4
I/O
Complement clock of differential SRC clock pair 4
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
3
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
SSOP/TSSOP Pin Description (Continued)
PIN #
PIN NAME
TYPE
29
CPU_STOP#/SRCC5
I/O
30
PCI_STOP#/SRCT5
I/O
DESCRIPTION
Stops all CPU Clocks, except those set to be free running clocks /
Complement clock of differential SRC pair. The function of this pin is set up by the power-up strap
on pin 6, PCI4/SRC5_EN. The logic value sampled on pin 6 at power-up sets the function as
follows:
0= CPU_STOP#
1 = SRC5
In AMT mode 3 bits are shifted in from the ICH to set the FSC, FSB, FSA values
Stops all PCI Clocks, except those set to be free running clocks /
Complement clock of differential SRC pair. The function of this pin is set up by the power-up strap
on pin 6, PCI4/SRC5_EN. The logic value sampled on pin 6 at power-up sets the function as
follows:
0= PCI_STOP#
1 = SRC5#
In AMT mode, this pin is a clock input which times the FSC, FSB, FSA bits shifted in on pin 37.
31
VDDSRC
PWR
VDD pin for SRC Pre-drivers, 3.3V nominal
32
SRCC6
OUT
Complement clock of low power differential SRC clock pair.
33
SRCT6
OUT
True clock of low power differential SRC clock pair.
34
GNDSRC
PWR
35
SRCC7/CR#_E
I/O
36
SRCT7/CR#_F
I/O
37
VDDSRC_IO
PWR
38
CPUC2_ITP/SRCC8
OUT
39
CPUT2_ITP/SRCT8
OUT
Ground for SRC clocks
SRC7 complement or Clock Request control E for SRC6 pair
The power-up default is SRC7#, but this pin may also be used as a Clock Request control of
SRC6 via SMBus. Before configuring this pin as a Clock Request Pin, the SRC7 output pair must
first be disabled in byte 3, bit 3 of SMBus configuration space . After the SRC output is disabled
(high-Z), the pin can then be set to serve as a Clock Request for SRC6 pair using byte 6, bit 7 of
SMBus configuration space
Byte 6, bit 7
0 = SRC7# enabled (default)
1= CR#_E controls SRC6.
SRC7 true or Clock Request control 8 for SRC8 pair
The power-up default is SRC7, but this pin may also be used as a Clock Request control of SRC8
via SMBus. Before configuring this pin as a Clock Request Pin, the SRC7 output pair must first be
disabled in byte 3, bit 3 of SMBus configuration space After the SRC output is disabled (high-Z),
the pin can then be set to serve as a Clock Request for SRC8 pair using byte 6, bit 6 of SMBus
configuration space
Byte 6, bit 6
0 = SRC7# enabled (default)
1 = CR#_F controls SRC8.
Power supply for SRC outputs. 1.05 to 3.3V +/-5%.
Complement clock of low power differential CPU2/Complement clock of differential SRC pair. The
function of this pin is determined by the latched input value on pin 7, PCIF5/ITP_EN on powerup.
The function is as follows:
Pin 7 latched input Value
0 = SRC8#
1 = ITP#
True clock of low power differential CPU2/True clock of differential SRC pair. The function of this
pin is determined by the latched input value on pin 7, PCIF5/ITP_EN on powerup. The function is
as follows:
Pin 7 latched input Value
0 = SRC8
1 = ITP
No Connect
40
NC
N/A
41
VDDCPU_IO
PWR
42
CPUC1_F
OUT
43
CPUT1_F
OUT
Supply for CPU outputs. 1.05 to 3.3V +/-5%.
Complement clock of low power differenatial CPU clock pair. This clock will be free-running during
iAMT.
True clock of low power differential CPU clock pair. This clock will be free-running during iAMT.
44
GNDCPU
PWR
Ground Pin for CPU Outputs
45
CPUC0
OUT
Complement clock of low power differential CPU clock pair.
46
CPUT0
OUT
True clock of low power differential CPU clock pair.
47
VDDCPU
PWR
Power Supply 3.3V nominal.
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
4
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
SSOP/TSSOP Pin Description (Continued)
PIN #
TYPE
DESCRIPTION
48
CK_PWRGD/PD#
PIN NAME
IN
49
FSLB/TEST_MODE
IN
50
GNDREF
PWR
Notifies CK505 to sample latched inputs, or iAMT entry/exit, or PWRDWN# mode
3.3V tolerant input for CPU frequency selection. Refer to input electrical characteristics for Vil_FS
and Vih_FS values. TEST_MODE is a real time input to select between Hi-Z and REF/N divider
mode while in test mode. Refer to Test Clarification Table.
Ground pin for crystal oscillator circuit
51
X2
OUT
Crystal output, nominally 14.318MHz.
52
X1
IN
Crystal input, Nominally 14.318MHz.
53
VDDREF
54
REF0/FSLC/TEST_SEL
I/O
55
SDATA
I/O
Power pin for the REF outputs, 3.3V nominal.
3.3V 14.318MHz reference clock/3.3V tolerant low threshold input for CPU frequency selection.
Refer to input electrical characteristics for Vil_FS and Vih_FS values/ TEST_SEL: 3-level latched
input to enable test mode. Refer to Test Clarification Table.
Data pin for SMBus circuitry, 5V tolerant.
56
SCLK
IN
Clock pin of SMBus circuitry, 5V tolerant.
PWR
Fully Integrated Regulator Connection for Desktop/Mobile Applications
ICS9LPR502
ICS9LPRS502
VDDCPU_IO, Pin 41
1.05V to 3.3V
(+/-5%)
CPU_IO Decoupling
Network
96_IO Decoupling
Network
NC
PIN 40
PLL3_IO Decoupling
Network
SRC_IO Decoupling
Network
VDDSRC_IO Pin 37, 26
VDDPLL3_IO, Pin 20
VDD96_IO, Pin 12
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
5
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
VDDSRCI/O
CPUC2_ITP/SRCC8
CPUT2_ITP/SRCT8
NC
VDDI/OCPU
CPUC1
CPUT1
GNDCPU
CPUC0
CPUT0
VDDCPU
CK_PWRGD/PD#
FSLB/TEST_MODE
GNDREF
SSOP/TSSOP Pin Description (Continued)
56 55 54 53 52 51 50 49 48 47 46 45 44 43
X2
X1
VDDREF
REF0/FSLC/TEST_SEL
1
2
3
4
SDATA 5
SCLK
PCI0/CR#_A
VDDPCI
PCI1/CR#_B
PCI2/TME
PCI3
PCI4/SRC5_EN
PCI_F5/ITP_EN
GNDPCI
6
7
8
9
10
11
12
13
14
ICS9LPRS502
42
41
40
39
38
SRCT7/CR#_F
SRCC7/CR#_E
GNDSRC
VDDSRC
37
36
35
34
33
32
31
30
29
CPU_STOP#/SRCC5
SRCT11
SRCC11
SRCC4
SRCT4
VDDSRCI/O
SRCC3/CR#_D
SRCT3/CR#_C
GNDSRC
PCI_STOP#/SRCT5
SRCC2/SATAC
SRCT2/SATAT
VDDPLL3I/O
GND
SRCC1/SE2
SRCT1/SE1
VDD
GND
DOTC_96/SRCC0
DOTT_96/SRCT0
VDDI/O96Mhz
GND48
USB_48MHz/FSLA
VDD48
15 16 17 18 19 20 21 22 23 24 25 26 27 28
56-pin MLF
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
6
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
MLF Pin Description
PIN #
PIN NAME
TYPE
1
X2
OUT
2
X1
3
VDDREF
4
REF0/FSLC/TEST_SEL
I/O
5
SDATA
I/O
6
SCLK
IN
7
PCI0/CR#_A
I/O
8
VDDPCI
9
PCI1/CR#_B
I/O
10
PCI2/TME
I/O
11
PCI3
12
PCI4/SRC5_EN
I/O
13
PCI_F5/ITP_EN
I/O
14
GNDPCI
IN
PWR
PWR
OUT
PWR
DESCRIPTION
Crystal output, nominally 14.318MHz.
Crystal input, Nominally 14.318MHz.
Power pin for the REF outputs, 3.3V nominal.
3.3V 14.318MHz reference clock/3.3V tolerant low threshold input for CPU frequency selection. Refer to input
electrical characteristics for Vil_FS and Vih_FS values/ TEST_SEL: 3-level latched input to enable test mode.
Refer to Test Clarification Table.
Data pin for SMBus circuitry, 5V tolerant.
Clock pin of SMBus circuitry, 5V tolerant.
3.3V PCI clock output or Clock Request control A for either SRC0 or SRC2 pair
The power-up default is PCI0 output, but this pin may also be used as a Clock Request control of SRC pair 0 or
SRC pair 2 via SMBus. Before configuring this pin as a Clock Request Pin, the PCI output must first be disabled in
byte 2, bit 0 of SMBus address space . After the PCI output is disabled (high-Z), the pin can then be set to serve
as a Clock Request pin for either SRC pair 2 or pair 0 using the CR#_A_EN bit located in byte 5 of SMBUs
address space.
Byte 5, bit 7
0 = PCI0 enabled (default)
1= CR#_A enabled. Byte 5, bit 6 controls whether CR#_A controls SRC0 or SRC2 pair
Byte 5, bit 6
0 = CR#_A controls SRC0 pair (default),
1= CR#_A controls SRC2 pair
Power supply pin for the PCI outputs, 3.3V nominal
3.3V PCI clock output/Clock Request control B for either SRC1 or SRC4 pair
The power-up default is PCI1 output, but this pin may also be used as a Clock Request control of SRC pair 1 or
SRC pair 4 via SMBus. Before configuring this pin as a Clock Request Pin, the PCI output must first be disabled in
byte 2, bit 1 of SMBus address space . After the PCI output is disabled (high-Z), the pin can then be set to serve
as a Clock Request pin for either SRC pair 1 or pair 4 using the CR#_B_EN bit located in byte 5 of SMBUs
address space.
Byte 5, bit 5
0 = PCI1 enabled (default)
1= CR#_B enabled. Byte 5, bit 6 controls whether CR#_B controls SRC1 or SRC4 pair
Byte 5, bit 4
0 = CR#_B controls SRC1 pair (default)
1= CR#_B controls SRC4 pair
3.3V PCI clock output / Trusted Mode Enable (TME) Latched Input. This pin is sampled on power-up as follows
0 = Overclocking of CPU and SRC Allowed
1 = Overclocking of CPU and SRC NOT allowed
After being sampled on power-up, this pin becomes a 3.3V PCI Output
3.3V PCI clock output.
3.3V PCI clock output / SRC5 pair or PCI_STOP#/CPU_STOP# enable strap. On powerup, the logic value on this
pin determines if the SRC5 pair is enabled or if CPU_STOP#/PCI_STOP# is enabled (pins 29 and 30). The latched
value controls the pin function on pins 29 and 30 as follows
0 = PCI_STOP#/CPU_STOP#
1 = SRC5/SRC5#
Free running PCI clock output and ITP/SRC8 enable strap. This output is not affected by the state of the
PCI_STOP# pin. On powerup, the state of this pin determines whether pins 38 and 39 are an ITP or SRC pair.
0 =SRC8/SRC8#
1 = ITP/ITP#
Ground for PCI clocks.
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
7
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
MLF Pin Description (Continued)
PIN #
15
PIN NAME
VDD48
TYPE
PWR
I/O
DESCRIPTION
Power supply for USB clock, nominal 3.3V.
Fixed 48MHz USB clock output. 3.3V./ 3.3V tolerant input for CPU frequency selection. Refer to input electrical
characteristics for Vil_FS and Vih_FS values.
Ground pin for the 48MHz outputs.
16
USB_48MHz/FSLA
17
GND48
PWR
18
VDD96_IO
PWR
19
DOTT_96/SRCT0
OUT
20
DOTC_96/SRCC0
OUT
21
GND
PWR
22
VDD
PWR
23
SRCT1/SE1
OUT
24
SRCC1/SE2
OUT
25
GND
PWR
26
VDDPLL3_IO
PWR
Power supply for PLL3 output. 1.05 to 3.3V +/-5%.
27
SRCT2/SATAT
OUT
True clock of differential SRC/SATA clock pair.
28
SRCC2/SATAC
OUT
Complement clock of differential SRC/SATA clock pair.
Power supply for DOT96 output. 1.05 to 3.3V +/-5%.
True clock of SRC or DOT96. The power-up default function is SRC0. After powerup, this pin function may be
changed to DOT96 via SMBus Byte 1, bit 7 as follows:
0= SRC0
1=DOT96
Complement clock of SRC or DOT96. The power-up default function is SRC0#. After powerup, this pin function
may be changed to DOT96# via SMBus Byte 1, bit 7 as follows
0= SRC0#
1=DOT96#
Ground pin for the DOT96 clocks.
Power supply for SRC / SE1 and SE2 clocks, 3.3V nominal.
True clock of differential SRC1 clock pair / 3.3V single-ended output. The powerup default is 100 MHz SRC, -0.5%
downspread. The pin function may be changed via SMBus B1b[4:1]
Complement clock of differential SRC1 clock pair / 3.3V single-ended output. The powerup default is 100 MHz
SRC, -0.5% downspread. The pin function may be changed via SMBus B1b[4:1]
Ground pin for SRC / SE1 and SE2 clocks, PLL3.
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
8
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
MLF Pin Description (Continued)
PIN #
PIN NAME
TYPE
DESCRIPTION
PWR
Ground pin for SRC clocks.
True clock of differential SRC clock pair/ Clock Request control C for either SRC0 or SRC2 pair
The power-up default is SRCCLK3 output, but this pin may also be used as a Clock Request control of SRC pair 0
or SRC pair 2 via SMBus. Before configuring this pin as a Clock Request Pin, the SRC3 output must first be
disabled in byte 4, bit 7 of SMBus address space . After the SRC3 output is disabled, the pin can then be set to
serve as a Clock Request pin for either SRC pair 2 or pair 0 using the CR#_C_EN bit located in byte 5 of SMBUs
address space.
Byte 5, bit 3
0 = SRC3 enabled (default)
1= CR#_C enabled. Byte 5, bit 2 controls whether CR#_C controls SRC0 or SRC2 pair
Byte 5, bit 2
0 = CR#_C controls SRC0 pair (default),
1= CR#_C controls SRC2 pair
Complementary clock of differential SRC clock pair/ Clock Request control D for either SRC1 or SRC4 pair
The power-up default is SRCCLK3 output, but this pin may also be used as a Clock Request control of SRC pair 1
or SRC pair 4 via SMBus. Before configuring this pin as a Clock Request Pin, the SRC3 output must first be
disabled in byte 4, bit 7 of SMBus address space . After the SRC3 output is disabled, the pin can then be set to
serve as a Clock Request pin for either SRC pair 1 or pair 4 using the CR#_D_EN bit located in byte 5 of SMBUs
address space.
Byte 5, bit 1
0 = SRC3 enabled (default)
1= CR#_D enabled. Byte 5, bit 0 controls whether CR#_D controls SRC1 or SRC4 pair
Byte 5, bit 0
0 = CR#_D controls SRC1 pair (default),
1= CR#_D controls SRC4 pair
Power supply for SRC outputs. 1.05 to 3.3V +/-5%.
29
GNDSRC
30
SRCT3/CR#_C
I/O
31
SRCC3/CR#_D
I/O
32
VDDSRC_IO
33
SRCT4
PWR
I/O
True clock of differential SRC clock pair 4
34
SRCC4
I/O
Complement clock of differential SRC clock pair 4
35
SRCC11
OUT
Complement clock of low power differential SRC clock pair.
36
SRCT11
OUT
37
CPU_STOP#/SRCC5
I/O
38
PCI_STOP#/SRCT5
I/O
True clock of low power differential SRC clock pair.
Stops all CPU Clocks, except those set to be free running clocks /
Complement clock of differential SRC pair. The function of this pin is set up by the power-up strap on pin 6,
PCI4/SRC5_EN. The logic value sampled on pin 6 at power-up sets the function as follows:
0= CPU_STOP#
1 = SRC5
In AMT mode 3 bits are shifted in from the ICH to set the FSC, FSB, FSA values
Stops all PCI Clocks, except those set to be free running clocks /
Complement clock of differential SRC pair. The function of this pin is set up by the power-up strap on pin 6,
PCI4/SRC5_EN. The logic value sampled on pin 6 at power-up sets the function as follows:
0= PCI_STOP#
1 = SRC5#
In AMT mode, this pin is a clock input which times the FSC, FSB, FSA bits shifted in on pin 37.
VDD pin for SRC Pre-drivers, 3.3V nominal
39
VDDSRC
PWR
40
GNDSRC
PWR
41
SRCC7/CR#_E
I/O
42
SRCT7/CR#_F
I/O
Ground for SRC clocks
SRC7 complement or Clock Request control E for SRC6 pair
The power-up default is SRC7#, but this pin may also be used as a Clock Request control of SRC6 via SMBus.
Before configuring this pin as a Clock Request Pin, the SRC7 output pair must first be disabled in byte 3, bit 3 of
SMBus configuration space . After the SRC output is disabled (high-Z), the pin can then be set to serve as a Clock
Request for SRC6 pair using byte 6, bit 7 of SMBus configuration space
Byte 6, bit 7
0 = SRC7# enabled (default)
1= CR#_E controls SRC6.
SRC7 true or Clock Request control 8 for SRC8 pair
The power-up default is SRC7, but this pin may also be used as a Clock Request control of SRC8 via SMBus.
Before configuring this pin as a Clock Request Pin, the SRC7 output pair must first be disabled in byte 3, bit 3 of
SMBus configuration space After the SRC output is disabled (high-Z), the pin can then be set to serve as a Clock
Request for SRC8 pair using byte 6, bit 6 of SMBus configuration space
Byte 6, bit 6
0 = SRC7# enabled (default)
1 = CR#_F controls SRC8.
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
9
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
MLF Pin Description (Continued)
PIN #
43
44
PIN NAME
VDDSRC_IO
CPUC2_ITP/SRCC8
TYPE
DESCRIPTION
PWR
Power supply for SRC outputs. 1.05 to 3.3V +/-5%.
OUT
Complement clock of low power differential CPU2/Complement clock of differential SRC pair. The function of this
pin is determined by the latched input value on pin 7, PCIF5/ITP_EN on powerup. The function is as follows:
Pin 7 latched input Value
0 = SRC8#
1 = ITP#
45
CPUT2_ITP/SRCT8
OUT
46
47
NC
VDDCPU_IO
NC
PWR
True clock of low power differential CPU2/True clock of differential SRC pair. The function of this pin is determined
by the latched input value on pin 7, PCIF5/ITP_EN on powerup. The function is as follows:
Pin 7 latched input Value
0 = SRC8
1 = ITP
Not Connected
Power supply for CPU outputs. 1.05 to 3.3V +/-5%.
48
CPUC1_F
OUT
Complement clock of low power differenatial CPU clock pair. This clock will be free-running during iAMT.
49
CPUT1_F
OUT
True clock of low power differential CPU clock pair. This clock will be free-running during iAMT.
50
GNDCPU
PWR
Ground Pin for CPU Outputs
51
CPUC0
OUT
Complement clock of low power differential CPU clock pair.
52
CPUT0
OUT
True clock of low power differential CPU clock pair.
53
VDDCPU
PWR
Power Supply 3.3V nominal.
54
CK_PWRGD/PD#
IN
55
FSLB/TEST_MODE
IN
56
GNDREF
PWR
Notifies CK505 to sample latched inputs, or iAMT entry/exit, or PWRDWN# mode
3.3V tolerant input for CPU frequency selection. Refer to input electrical characteristics for Vil_FS and Vih_FS
values. TEST_MODE is a real time input to select between Hi-Z and REF/N divider mode while in test mode. Refer
to Test Clarification Table.
Ground pin for crystal oscillator circuit
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
10
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
General Description
ICS9LPRS502 follows Intel CK505 Yellow Cover specification. This clock synthesizer provides a single chip solution for
next generation Intel processors and Intel chipsets. ICS9LPRS502 is driven with a 14.318MHz crystal. It also provides a
tight ppm accuracy output for Serial ATA and PCI-Express support.
Funtional Block Diagram
X1
REF
R EF
X2
OSC
CPU(1:0)
SRC8/ITP
CPU
CPU PLL1
SS
SRC
SRC(7:3)
SR C _M A IN
PCI33MHz
SRC
PLL3
SS
PCI(5:0)
PCI33MHz
SRC2/SATA
FSLA
CKPWRGD/PD#
PCI_STOP#
SRC1/SE(2:1)
CPU_STOP#
CR#_(A:F)
SRC5_EN
Control
Logic
Differential Output
ITP_EN
SE Outputs
7
FSLC/TESTSEL
FSLB/TESTMODE
SRC0/DOT96
SATA
PLL2
Non-SS
DOT96MHz
48MHz
48MHz
Power Groups
Pin Number
VDD
GND
41
44
47
44
26, 37
23,34
31
23,34
20
19
16
19
12
11
9
11
53
50
2
8
Description
CPUCLK
Low power outputs
Master Clock, Analog
Low power outputs
SRCCLK
PLL 1
Low power outputs
PLL3/SE
PLL 3
DOT 96Mhz
Low power outputs
USB 48
Xtal, REF
PCICLK
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
11
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Absolute Maximum Ratings
PARAMETER
SYMBOL
CONDITIONS
Maximum Supply Voltage
VDDxxx
Supply Voltage
MIN
MAX
4.6
V
Maximum Supply Voltage
VDDxxx_IO
Low-Voltage Differential I/O Supply
3.8
V
1,7
Maximum Input Voltage
VIH
3.3V LVCMOS Inputs
4.6
V
1,7,8
Minimum Input Voltage
VIL
Any Input
GND - 0.5
V
1,7
Storage Temperature
Ts
-
-65
Input ESD protection
ESD prot
Human Body Model
2000
150
UNITS Notes
°
1,7
C
1,7
V
1,7
Electrical Characteristics - Input/Supply/Common Output Parameters
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
UNITS Notes
Ambient Operating Temp
Tambient
-
0
70
°C
1
Supply Voltage
VDDxxx
Supply Voltage
3.135
3.465
V
1
Supply Voltage
VDDxxx_IO
Low-Voltage Differential I/O Supply
1.05
3.465
V
1
Input High Voltage
VIHSE
Single-ended inputs
2
VDD + 0.3
V
1
Input Low Voltage
VILSE
Single-ended inputs
VSS - 0.3
0.8
V
1
Input Leakage Current
IIN
-5
5
uA
1
Input Leakage Current
IINRES
VIN = VDD , VIN = GND
Inputs with pull or pull down
resistors
VIN = VDD , VIN = GND
-200
200
uA
1
Output High Voltage
VOHSE
Single-ended outputs, IOH = -1mA
Output Low Voltage
VOLSE
Single-ended outputs, IOL = 1 mA
Output High Voltage
VOHDIF
Differential Outputs
Output Low Voltage
Low Threshold InputHigh Voltage (Test Mode)
Low Threshold InputHigh Voltage
Low Threshold InputLow Voltage
VOLDIF
Differential Outputs
VIH_FS_TEST
3.3 V +/-5%
VIH_FS
Operating Supply Current
V
1
0.4
V
1
0.9
V
1
0.4
V
1
2
VDD + 0.3
V
1
3.3 V +/-5%
0.7
1.5
V
1
VIL_FS
3.3 V +/-5%
VSS - 0.3
0.35
V
1
IDD_DEFAULT
3.3V supply, PLL3 off
250
mA
1
IDD_PLL3DIF
250
mA
1
250
mA
1
80
mA
1
IDD_PD3.3
3.3V supply, PLL3 Differential Out
3.3V supply, PLL3 Single-ended
Out
0.8V supply, Differential IO current,
all outputs enabled
3.3V supply, Power Down Mode
10
mA
1
IDD_PDIO
0.8V IO supply, Power Down Mode
0.1
mA
1
IDD_PLL3SE
IDD_IO
Power Down Current
2.4
0.7
25
IDD_iAMT3.3
3.3V supply, iAMT Mode
26
mA
1
IDD_iAMT0.8
0.8V IO supply, iAMTMode
8
mA
1
Input Frequency
Fi
VDD = 3.3 V
15
MHz
2
Pin Inductance
Lpin
7
nH
1
CIN
Logic Inputs
5
pF
1
Input Capacitance
COUT
Output pin capacitance
6
pF
1
CINX
X1 & X2 pins
6
pF
1
fSSMOD
Triangular Modulation
33
kHz
1
iAMT Mode Current
Spread Spectrum Modulation
Frequency
1.5
30
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
12
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
AC Electrical Characteristics - Input/Common Parameters
PARAMETER
SYMBOL
Clk Stabilization
TSTAB
Tdrive_SRC
T DRSRC
Tdrive_PD#
TDRPD
Tdrive_CPU
T DRSRC
Tfall_PD#
T FALL
Trise_PD#
T RISE
CONDITIONS
From VDD Power-Up or deassertion of PD# to 1st clock
SRC output enable after
PCI_STOP# de-assertion
Differential output enable after
PD# de-assertion
CPU output enable after
CPU_STOP# de-assertion
MIN
Fall/rise time of PD#, PCI_STOP#
and CPU_STOP# inputs
MAX
UNITS Notes
1.8
ms
1
15
ns
1
300
us
1
10
ns
1
5
ns
1
5
ns
1
AC Electrical Characteristics - Low Power Differential Outputs
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
UNITS NOTES
Rising Edge Slew Rate
tSLR
Differential Measurement
2.5
8
V/ns
1,2
Falling Edge Slew Rate
tFLR
Differential Measurement
2.5
8
V/ns
1,2
Slew Rate Variation
tSLVAR
Single-ended Measurement
20
%
1
Maximum Output Voltage
VHIGH
Includes overshoot
1150
mV
1
Minimum Output Voltage
VLOW
Includes undershoot
-300
mV
1
Differential Voltage Swing
VSWING
Differential Measurement
300
mV
1
Crossing Point Voltage
VXABS
Single-ended Measurement
300
Crossing Point Variation
VXABSVAR
Single-ended Measurement
550
mV
1,3,4
140
mV
1,3,5
Duty Cycle
DCYC
Differential Measurement
55
%
1
CPU Jitter - Cycle to Cycle
CPUJ C2C
Differential Measurement
85
ps
1
SRC Jitter - Cycle to Cycle
SRCJ C2C
Differential Measurement
125
ps
1
DOT Jitter - Cycle to Cycle
DOTJ C2C
Differential Measurement
250
ps
1
CPU[1:0] Skew
CPUSKEW10
Differential Measurement
100
ps
1
CPU[2_ITP:0] Skew
CPUSKEW20
Differential Measurement
150
ps
1
SRC[10:0] Skew
SRCSKEW
Differential Measurement
3000
ps
1
45
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
13
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Electrical Characteristics - PCICLK/PCICLK_F
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
Long Accuracy
ppm
see Tperiod min-max values
-300
300
Clock period
Tperiod
Absolute min/max period
Tabs
33.33MHz output nominal/spread
29.49100
Output High Voltage
VOH
IOH = -1 mA
2.4
Output Low Voltage
VOL
IOL = 1 mA
Output High Current
33.33MHz output nominal
33.33MHz output spread
30.00900
ns
6
30.15980
ns
6
30.65980
ns
6
V
1
V
1
mA
1
mA
1
0.4
V OH @MIN = 1.0 V
IOH
29.99100
-33
VOH@MAX = 3.135 V
VOL @ MIN = 1.95 V
UNITS NOTES
1,6
ppm
-33
30
mA
1
38
mA
1
4
V/ns
1
Output Low Current
IOL
Rising Edge Slew Rate
tSLR
Measured from 0.8 to 2.0 V
Falling Edge Slew Rate
tFLR
Measured from 2.0 to 0.8 V
1
4
V/ns
1
Duty Cycle
dt1
VT = 1.5 V
45
55
%
1
250
ps
1
ps
1,9
ps
1
VOL @ MAX = 0.4 V
Skew
tskew
VT = 1.5 V
Intentional PCI-PCI delay
tdelay
VT = 1.5 V
Jitter, Cycle to cycle
tjcyc-cyc
VT = 1.5 V
1
200 nominal
500
Intentional PCI Clock to Clock Delay
200 ps nominal steps
PCI0
PCI1
PCI2
PCI3
PCI4
PCI_F5
1.0ns
Electrical Characteristics - USB48MHz
PARAMETER
Long Accuracy
SYMBOL
ppm
CONDITIONS
see Tperiod min-max values
MIN
-100
MAX
100
UNITS NOTES
ppm
1,2
Clock period
Tperiod
48.00MHz output nominal
20.83125
20.83542
ns
2
Absolute min/max period
Tabs
48.00MHz output nominal
20.48130
21.18540
ns
2
Output High Voltage
VOH
IOH = -1 mA
2.4
V
1
Output Low Voltage
VOL
IOL = 1 mA
0.4
V
1
Output High Current
IOH
mA
1
-23
mA
1
Output Low Current
IOL
mA
1
27
mA
1
V OH @MIN = 1.0 V
-29
VOH@MAX = 3.135 V
VOL @ MIN = 1.95 V
29
VOL @ MAX = 0.4 V
Rising Edge Slew Rate
tSLR
Measured from 0.8 to 2.0 V
1
2
V/ns
1
Falling Edge Slew Rate
tFLR
Measured from 2.0 to 0.8 V
1
2
V/ns
1
Duty Cycle
dt1
VT = 1.5 V
45
55
%
1
Jitter, Cycle to cycle
tjcyc-cyc
VT = 1.5 V
350
ps
1
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
14
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Electrical Characteristics - REF-14.318MHz
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
Long Accuracy
ppm
see Tperiod min-max values
-300
300
ppm
1,2
Clock period
Tperiod
14.318MHz output nominal
69.8203
69.8622
ns
2
Absolute min/max period
Tabs
14.318MHz output nominal
69.8203
70.86224
ns
2
Output High Voltage
VOH
IOH = -1 mA
2.4
Output Low Voltage
VOL
IOL = 1 mA
Output High Current
IOH
Output Low Current
IOL
Rising Edge Slew Rate
tSLR
Measured from 0.8 to 2.0 V
Falling Edge Slew Rate
tFLR
Measured from 2.0 to 0.8 V
Duty Cycle
dt1
VT = 1.5 V
Jitter
tjcyc-cyc
VT = 1.5 V
VOH @MIN = 1.0 V,
VOH@MAX = 3.135 V
VOL @MIN = 1.95 V,
VOL @MAX = 0.4 V
UNITS Notes
V
1
0.4
V
1
-33
-33
mA
1
30
38
mA
1
1
4
V/ns
1
1
4
V/ns
1
45
55
%
1
1000
ps
1
Electrical Characteristics - SMBus Interface
PARAMETER
SYMBOL
SMBus Voltage
VDD
CONDITIONS
Low-level Output Voltage
Current sinking at
VOLSMB = 0.4 V
SCLK/SDATA
Clock/Data Rise Time
SCLK/SDATA
Clock/Data Fall Time
Maximum SMBus Operating
Frequency
VOLSMB
@ IPULLUP
IPULLUP
SMB Data Pin
T FI2C
(Max VIL - 0.15) to
(Min VIH + 0.15)
(Min VIH + 0.15) to
(Max VIL - 0.15)
F SMBUS
Block Mode
T RI2C
MIN
MAX
2.7
5.5
V
1
0.4
V
1
mA
1
1000
ns
1
300
ns
1
100
kHz
1
4
UNITS Notes
Notes on Electrical Characteristics:
1Guaranteed
by design and characterization, not 100% tested in production.
2
Slew rate measured through Vswing centered around differential zero
3
Vxabs is defined as the voltage where CLK = CLK#
4
Only applies to the differential rising edge (CLK rising and CLK# falling)
Defined as the total variation of all crossing voltages of CLK rising and CLK# falling. Matching applies to rising edge rate of
CLK and falling edge of CLK#. It is measured using a +/-75mV window centered on the average cross point where CLK meets
CLK#. The average cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate
calculations.
6 All Long Term Accuracy and Clock Period specifications are guaranteed assuming that REFOUT is at 14.31818MHz
5
7
Operation under these conditions is neither implied, nor guaranteed.
8
Maximum input voltage is not to exceed maximum VDD
9
See PCI Clock-to-Clock Delay Figure
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
15
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Table 1: CPU Frequency Select Table
2
FSLC
B0b7
0
0
0
0
1
1
1
1
1
FSLB
B0b6
0
0
1
1
0
0
1
1
1
FS LA
B0b5
0
1
0
1
0
1
0
1
CPU
MHz
SRC
MHz
PCI
MHz
REF
MHz
USB
MHz
DOT
MHz
266.66
133.33
200.00
166.66
333.33
100.00
400.00
100.00
33.33
14.318
48.00
96.00
Reserved
1. FSLA and FSLB are low-threshold inputs.Please see VIL_FS and VIH_FS specifications in
the Input/Supply/Common Output Parameters Table for correct values.
Also refer to the Test Clarification Table.
2. FSLC is a three-level input. Please see the VIL_FS and VIH_FS
specifications in the Input/Supply/Common Output Parameters Table for correct values.
Table 2: PLL3 Quick Configuration
B1b4
B1b3
B1b2
B1b1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Pin 17
Pin 18
MHz
MHz
100.00
100.00
100.00
100.00
100.00
100.00
N/A
24.576
24.576
98.304
27.000
25.000
N/A
N/A
N/A
100.00
100.00
100.00
100.00
100.00
100.00
N/A
24.576
98.304
98.304
27.000
25.000
N/A
N/A
N/A
Spread
Comment
%
PLL 3 disabled
0.5% Down Spread
SRCCLK1 from SRC_MAIN
0.5% Down Spread
Only SRCCLK1 from PLL3
1% Down Spread
Only SRCCLK1 from PLL3
1.5% Down Spread
Only SRCCLK1 from PLL3
2% Down Spread
Only SRCCLK1 from PLL3
2.5% Down Spread
Only SRCCLK1 from PLL3
N/A
N/A
None
24.576Mhz on SE1 and SE2
None
24.576Mhz on SE1, 98.304Mhz on SE2
None
98.304Mhz on SE1 and SE2
None
27Mhz on SE1 and SE2
None
25Mhz on SE1 and SE2
N/A
N/A
N/A
N/A
N/A
N/A
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
16
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Table 3: IO_Vout select table
B9b2
B9b1
B9b0 IO_Vout
0.3V
0
0
0
0.4V
0
0
1
0.5V
0
1
0
0.6V
0
1
1
0.7V
1
0
0
0.8V
1
0
1
0.9V
1
1
0
1.0V
1
1
1
Table 4: Device ID table
B8b7
B8b6
B8b5
B8b4
Comment
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
56 pin TSSOP/QFN
64 pin TSSOP/QFN
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
17
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
PCI_STOP# Power Management
Single-ended Clocks
SMBus OE Bit
PCI_STOP#
1
Stop Drive Mode
X
Stoppable
Running
Free running
Running
Low
Low
0
Enable
0
1
Disable
X
Low
X
Differential Clocks
(Except CPU)
Stoppable Free running
Running
Running
CK= High
Running
CK# = Low
CK= Pull
down
Running
CK# = Low
CK= Pull down, CK# = Low
CPU_STOP# Power Management
SMBus OE Bit
PCI_STOP#
Stop Drive Mode
1
X
0
Enable
0
1
Disable
X
X
CR#
1
0
X
Stop Drive Mode
Differential Clocks
Stoppable
Free running
Running
Running
CK= High
Running
CK# = Low
CK= Pull down
Running
CK# = Low
Low
CR# Power Management
SMBus OE Bit
Enable
Disable
X
Differential Clocks
Stoppable
Free running
Running
Running
CK= Pull down, CK# = Low
CK = Pull down, CK# = Low
PD# Power Management
Differential Clocks
(Except CPU1)
CPU1
Latches Open
CK= Pull down, CK# = Low
CK= Pull down, CK# = Low
Power Down
CK= Pull down
CK# = Low
CK= Pull down
CK# = Low
M1
CK= Pull down
CK# = Low
Running
Virtual Power Cycle
to Latches Open
CK= Pull down, CK# = Low
CK= Pull down, CK# = Low
Single-ended Clocks
Device State
w/o Latched input w/Latched input
Low
Hi-Z
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
18
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
General SMBus serial interface information for the ICS9LPRS502
How to Write:
How to Read:
Controller (host) sends a start bit.
Controller (host) sends the write address D2 (H)
ICS clock will acknowledge
Controller (host) sends the beginning byte location = N
ICS clock will acknowledge
Controller (host) sends the data byte count = X
ICS clock will acknowledge
Controller (host) starts sending Byte N through
Byte N + X -1
• ICS clock will acknowledge each byte one at a time
• Controller (host) sends a Stop bit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Controller (host) will send start bit.
Controller (host) sends the write address D2 (H)
ICS clock will acknowledge
Controller (host) sends the begining byte
location = N
ICS clock will acknowledge
Controller (host) will send a separate start bit.
Controller (host) sends the read address D3 (H)
ICS clock will acknowledge
ICS clock will send the data byte count = X
ICS clock sends Byte N + X -1
ICS clock sends Byte 0 through byte X (if X(H)
was written to byte 8).
Controller (host) will need to acknowledge each byte
Controller (host) will send a not acknowledge bit
Controller (host) will send a stop bit
Index Block Write Operation
Controller (Host)
starT bit
T
Slave Address D2(H)
WR
WRite
Index Block Read Operation
Controller (Host)
T
starT bit
Slave Address D2(H)
WR
WRite
ICS (Slave/Receiver)
ICS (Slave/Receiver)
ACK
ACK
Beginning Byte = N
Beginning Byte = N
ACK
ACK
RT
Repeat starT
Slave Address D3(H)
RD
ReaD
Data Byte Count = X
ACK
Beginning Byte N
ACK
X Byte
ACK
Data Byte Count = X
ACK
Beginning Byte N
Byte N + X - 1
ACK
X Byte
ACK
P
stoP bit
Byte N + X - 1
N
P
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
19
Not acknowledge
stoP bit
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Byte 0 FS Readback and PLL Selection Register
Bit
7
6
5
Pin
-
Name
FSLC
FSLB
FSLA
4
-
iAMT_EN
3
2
1
-
Reserved
SRC_Main_SEL
SATA_SEL
0
-
PD_Restore
Description
Type
0
1
CPU Freq. Sel. Bit (Most Significant)
R
See Table 1 : CPU Frequency Select Table
CPU Freq. Sel. Bit
R
CPU Freq. Sel. Bit (Least Significant)
R
Set via SMBus or dynamically by CK505 if detects
RW
Legacy Mode
iAMT Enabled
dynamic M1
Reserved
RW
Select source for SRC Main
RW
SRC Main = PLL1
SRC Main = PLL3
Select source for SATA clock
RW
SATA = SRC_Main
SATA = PLL2
1 = on Power Down de-assert return to last known
state
0 = clear all SMBus configurations as if cold power-on
Configuration Saved
RW Configuration Not Saved
and go to latches open state
This bit is ignored and treated at '1' if device is in iAMT
mode.
Default
Latch
Latch
Latch
0
0
0
0
1
Byte 1 DOT96 Select and PLL3 Quick Config Register
Bit
7
6
5
4
3
2
1
Pin
13/14
-
0
Name
SRC0_SEL
PLL1_SSC_SEL
PLL3_SSC_SEL
PLL3_CF3
PLL3_CF2
PLL3_CF1
PLL3_CF0
Description
Select SRC0 or DOT96
Select 0.5% down or center SSC
Select 0.5% down or center SSC
PLL3 Quick Config Bit 3
PLL3 Quick Config Bit 2
PLL3 Quick Config Bit 1
PLL3 Quick Config Bit 0
Type
RW
RW
RW
RW
RW
RW
RW
PCI_SEL
PCI_SEL
RW
Description
Output enable for REF, if disabled output is tri-stated
Output enable for USB
Output enable for PCI5
Output enable for PCI4
Output enable for PCI3
Output enable for PCI2
Output enable for PCI1
Output enable for PCI0
Type
RW
RW
RW
RW
RW
RW
RW
RW
Output
Output
Output
Output
Output
Output
Output
Output
0
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Output
Output
Output
Output
Output
Output
Output
Output
1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Default
1
1
1
1
1
1
1
1
Type
RW
RW
RW
RW
RW
RW
RW
RW
Output
Output
Output
Output
Output
Output
Output
Output
0
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Output
Output
Output
Output
Output
Output
Output
Output
1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Default
1
1
1
1
1
1
1
1
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
Output Disabled
Output Disabled
Output Disabled
Output Disabled
Output Disabled
Output Disabled
Spread Disabled
Spread Disabled
1
Output Enabled
Output Enabled
Output Enabled
Output Enabled
Output Enabled
Output Enabled
Spread Enabled
Spread Enabled
Default
1
1
1
1
1
1
1
1
0
SRC0
Down spread
Down spread
1
DOT96
Center spread
Center spread
See Table 2: PLL3 Quick Configuration
Only applies if Byte 0, bit 2 = 0.
PCI from PLL1
PCI from SRC_MAIN
Default
0
0
0
0
0
0
1
1
Byte 2 Output Enable Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
REF_OE
USB_OE
PCIF5_OE
PCI4_OE
PCI3_OE
PCI2_OE
PCI1_OE
PCI0_OE
Byte 3 Output Enable Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
SRC11_OE
SRC10_OE
SRC9_OE
SRC8/ITP_OE
SRC7_OE
SRC6_OE
SRC5_OE
SRC4_OE
Description
Output enable for SRC11
Output enable for SRC10
Output enable for SRC9
Output enable for SRC8 or ITP
Output enable for SRC7
Output enable for SRC6
Output enable for SRC5
Output enable for SRC4
Byte 4 Output Enable and Spread Spectrum Disable Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
SRC3_OE
SATA/SRC2_OE
SRC1_OE
SRC0/DOT96_OE
CPU1_OE
CPU0_OE
PLL1_SSC_ON
PLL3_SSC_ON
Description
Output enable for SRC3
Output enable for SATA/SRC2
Output enable for SRC1
Output enable for SRC0/DOT96
Output enable for CPU1
Output enable for CPU0
Enable PLL1's spread modulation
Enable PLL3's spread modulation
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
20
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Byte 5 Clock Request Enable/Configuration Register
Bit
Pin
Name
7
CR#_A_EN
6
5
4
3
2
1
0
CR#_A_SEL
CR#_B_EN
CR#_B_SEL
CR#_C_EN
CR#_C_SEL
CR#_D_EN
CR#_D_SEL
Description
Enable CR#_A (clk req),
PCI0_OE must be = 1 for this bit to take effect
Sets CR#_A to control either SRC0 or SRC2
Enable CR#_B (clk req)
Sets CR#_B -> SRC1 or SRC4
Enable CR#_C (clk req)
Sets CR#_C -> SRC0 or SRC2
Enable CR#_D (clk req)
Sets CR#_D -> SRC1 or SRC4
Type
0
1
Default
RW
Disable CR#_A
Enable CR#_A
0
RW
RW
RW
RW
RW
RW
RW
CR#_A -> SRC0
Disable CR#_B
CR#_B -> SRC1
Disable CR#_C
CR#_C -> SRC0
Disable CR#_D
CR#_D -> SRC1
CR#_A -> SRC2
Enable CR#_B
CR#_B -> SRC4
Enable CR#_C
CR#_C -> SRC2
Enable CR#_D
CR#_D -> SRC4
0
0
0
0
0
0
0
1
Enable CR#_E
Enable CR#_F
Enable CR#_G
Enable CR#_H
Default
0
0
0
0
0
0
Byte 6 Clock Request Enable/Configuration and Stop Control Register
Bit
7
6
5
4
3
2
Pin
1
0
Name
CR#_E_EN
CR#_F_EN
CR#_G_EN
CR#_H_EN
Reserved
Reserved
SSCD_STP_CRTL
(SRC1)
SRC_STP_CRTL
Description
Enable CR#_E (clk req) -> SRC6
Enable CR#_F (clk req) -> SRC8
Enable CR#_G (clk req) -> SRC9
Enable CR#_H (clk req) -> SRC10
Reserved
Reserved
Type
RW
RW
RW
RW
RW
RW
0
Disable CR#_E
Disable CR#_F
Disable CR#_G
Disable CR#_H
If set, SSCD (SRC1) stops with PCI_STOP#
RW
Free Running
If set, SRCs (except SRC1) stop with PCI_STOP#
RW
Free Running
Type
R
R
R
R
R
R
R
R
0
0
Reserved
Reserved
Output enable for SE1
Output enable for SE2
Type
R
R
R
R
RW
RW
RW
RW
Disabled
Disabled
Description
Type
Stops with PCI_STOP#
assertion
Stops with PCI_STOP#
assertion
0
0
Byte 7 Vendor ID/ Revision ID
Bit
7
6
5
4
3
2
1
0
Pin
Name
Rev Code Bit 3
Rev Code Bit 2
Rev Code Bit 1
Rev Code Bit 0
Vendor ID bit 3
Vendor ID bit 2
Vendor ID bit 1
Vendor ID bit 0
Description
Revision ID
Vendor ID
ICS is 0001, binary
1
Default
X
X
X
X
0
0
0
1
1
Enabled
Enabled
Default
0
0
0
0
0
0
0
0
0
1
Default
0
Vendor specific
Byte 8 Device ID and Output Enable Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
Device_ID3
Device_ID2
Device_ID1
Device_ID0
Reserved
Reserved
SE1_OE
SE2_OE
Description
Table of Device identifier codes, used for
differentiating between CK505 package options,
etc.
See Device ID Table
Byte 9 Output Control Register
Bit
Pin
Name
7
PCIF5 STOP EN
Allows control of PCIF5 with assertion of PCI_STOP#
RW
Free running
Stops with PCI_STOP#
assertion
6
5
4
3
2
1
0
TME_Readback
Reserved
Test Mode Select
Test Mode Entry
IO_VOUT2
IO_VOUT1
IO_VOUT0
Truested Mode Enable (TME) strap status
Reserved
Allows test select, ignores REF/FSC/TestSel
Allows entry into test mode, ignores FSB/TestMode
IO Output Voltage Select (Most Significant Bit)
IO Output Voltage Select
IO Output Voltage Select (Least Significant Bit)
R
RW
RW
RW
RW
RW
RW
normal operation
Outputs HI-Z
Normal operation
no overclocking
Outputs = REF/N
Test mode
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
21
See Table 3: V_IO Selection
(Default is 0.8V)
0
1
0
0
1
0
1
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Byte 10 CK505 Rev 0.85 functions (ICS Rev H silicon and higher)
Bit
7
6
5
4
3
2
1
0
Pin
Type
R
RW
RW
RW
RW
RW
RW
RW
0
CPU/PCI Stop Enabled
TBD
TBD
TBD
TBD
TBD
Free Running
Free Running
1
SRC5 Enabled
TBD
TBD
TBD
TBD
TBD
Stoppable
Stoppable
Default
Latch
0
0
0
0
0
1
1
Type
RW
RW
RW
RW
RW
RW
R
RW
0
TBD
TBD
TBD
TBD
Off in iAMT
Off in iAMT
non-Gen2
Free Running
1
TBD
TBD
TBD
TBD
Free running in iAMT
Free running in iAMT
PCIe Gen2 compliant
Stoppable
Default
0
0
0
0
0
1
0
1
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
1
Default
0
0
0
0
1
1
0
1
Type
RW
RW
RW
RW
The decimal representation of M and N Divider in Byte
RW
13 and 14 will configure the VCO frequency. Default
RW
at power up = latch-in or Byte 0 Rom table.
RW
RW
0
-
1
-
Default
X
X
X
X
X
X
X
X
0
-
1
-
Default
X
X
X
X
X
X
X
X
Name
SRC5_EN Readback
Reserved
Reserved
Reserved
Reserved
Reserved
CPU 1 Stop Enable
CPU 0 Stop Enable
Description
Readback of SRC5 enable latch
Reserved
Enables control of CPU1 with CPU_STOP#
Enables control of CPU 0 with CPU_STOP#
Byte 11 CK505 Rev 1.0 functions (ICS Rev P silicon and higher)
Bit
7
6
5
4
3
2
1
0
Pin
Name
Reserved
Reserved
Reserved
Reserved
CPU2_iAMT_EN
CPU1_iAMT_EN
PCIe-Gen2
CPU2 Stop Enable
Description
Reserved
Enables CPU2(ITP) output in iAMT state (M1)
Enables CPU1 output in iAMT state (M1)
PCIe-Gen2 status
Enables control of CPU2(ITP) with CPU_STOP#
Byte 12 Byte Count Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
Reserved
Reserved
BC5
BC4
BC3
BC2
BC1
BC0
Description
Read Back byte count register,
max bytes = 32
Byte 13 CK505 PLL1 M/N Programming Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
N Div8
N Div9
M Div5
M Div4
M Div3
M Div2
M Div1
M Div0
Description
N Divider 8
N Divider 9
Byte 14 CK505 PLL1 M/N Programming Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
N Div7
N Div6
N Div5
N Div4
N Div3
N Div2
N Div1
N Div0
Description
Type
RW
RW
RW
The decimal representation of M and N Divider in Byte
RW
13 and 14 will configure the VCO frequency. Default
RW
at power up = latch-in or Byte 0 Rom table.
RW
RW
RW
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
22
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Byte 15 CK505 PLL1 Spread Spectrum Control Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
SSP7
SSP6
SSP5
SSP4
SSP3
SSP2
SSP1
SSP0
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
-
1
-
Default
X
X
X
X
X
X
X
X
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
-
1
-
Default
0
x
X
X
X
X
X
X
Type
RW
RW
RW
RW
The decimal representation of M and N Divider in Byte
RW
17 and 18 will configure the VCO frequency. Default
RW
at power up = latch-in or Byte 0 Rom table.
RW
RW
0
-
1
-
Default
X
X
X
X
X
X
X
X
0
-
1
-
Default
X
X
X
X
X
X
X
X
0
-
1
-
Default
X
X
X
X
X
X
X
X
Description
These Spread Spectrum bits will program the spread
pecentage. Contact ICS for the correct values.
Byte 16 CK505 PLL1 Spread Spectrum Control Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
Reserved
SSP14
SSP13
SSP12
SSP11
SSP10
SSP9
SSP8
Description
Reserved
These Spread Spectrum bits will program the spread
pecentage. Contact ICS for the correct values.
Byte 17 CK505 PLL3 M/N Programming Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
N Div8
N Div9
M Div5
M Div4
M Div3
M Div2
M Div1
M Div0
Description
N Divider 8
N Divider 9
Byte 18 CK505 PLL3 M/N Programming Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
N Div7
N Div6
N Div5
N Div4
N Div3
N Div2
N Div1
N Div0
Description
Type
RW
RW
RW
The decimal representation of M and N Divider in Byte
RW
17 and 18 will configure the VCO frequency. Default
RW
at power up = latch-in or Byte 0 Rom table.
RW
RW
RW
Byte 19 CK505 PLL3 Spread Spectrum Control Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
SSP7
SSP6
SSP5
SSP4
SSP3
SSP2
SSP1
SSP0
Description
These Spread Spectrum bits will program the spread
pecentage. Contact ICS for the correct values.
Type
RW
RW
RW
RW
RW
RW
RW
RW
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
23
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Byte 20 CK505 PLL3 Spread Spectrum Control Register
Bit
7
6
5
4
3
2
1
0
Pin
Name
Reserved
SSP14
SSP13
SSP12
SSP11
SSP10
SSP9
SSP8
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
-
1
-
Default
0
X
X
X
X
X
X
X
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
1
Disable
Disable
Enable
Enable
Default
0
0
0
0
0
0
0
0
Description
PLL 1 M/N Programming
(Intel PLL1 CPU)
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
-
1
-
Default
X
X
X
X
X
X
X
X
Description
PLL 1 M/N Programming
(Intel PLL1 CPU)
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
-
1
-
Default
X
X
X
X
X
X
X
X
0
1
off
off
on
on
Default
0
0
0
0
0
0
Note
1
Description
Reserved
These Spread Spectrum bits will program the spread
pecentage. Contact ICS for the correct values.
Byte 21 M/N Enables
Bit
7
6
5
4
3
2
1
0
Pin
Name
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
M/N Enable CPU
M/N Enable
Description
Byte 22 CPU M/N Programming
Bit
7
6
5
4
3
2
1
0
Pin
Name
N Div bit 8
N Div bit 9
M Div Bit 5
M Div Bit 4
M Div Bit 3
M Div Bit 2
M Div Bit 1
M Div Bit 0
Byte 23 CPU M/N Programming
Bit
7
6
5
4
3
2
1
0
Pin
Name
N Div bit 7
N Div bit 6
N Div bit 5
N Div bit 4
N Div bit 3
N Div bit 2
N Div bit 1
N Div Bit 0
Bytes 24-62 Reserved
Byte 63 Special Power Management Features (Rev P Silicon and Higher)
Bit
7
6
5
4
3
2
1
0
Pin
Name
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SATA PLL
XTAL PD Control
Description
Power Management Feature
Controls XTAL on/off in legacy PD
RW
RW
RW
RW
RW
RW
RW
RW
RW
Note: Default is "off" for Rev P Silicon and higher.
*Accessing any SMBus bytes not shown in the datasheet could result in incorrect clock functions.
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
24
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
Test Clarification Table
Comments
HW
SW
FSLB/
TEST
TEST_MOD
FSLC/
ENTRY BIT
E
TEST_SEL
B9b3
HW PIN
HW PIN
Power-up w/ TEST_SEL = 1 to enter test mode
Cycle power to disable test mode
FSLC./TEST_SEL -->3-level latched input
If power-up w/ V>2.0V then use TEST_SEL
If power-up w/ V<2.0V then use FSLC
FSLB/TEST_MODE -->low Vth input
TEST_MODE is a real time input
If TEST_SEL HW pin is 0 during power-up,
test mode can be invoked through B9b3.
If test mode is invoked by B9b3, only B9b4
is used to select HI-Z or REF/N
FSLB/TEST_Mode pin is not used.
Cycle power to disable test mode, one shot control
REF/N or
HI-Z
B9b4
<2.0V
>2.0V
>2.0V
>2.0V
X
0
0
1
0
X
X
X
0
0
1
0
OUTPUT
NORMAL
HI-Z
REF/N
REF/N
>2.0V
1
X
1
REF/N
<2.0V
X
1
0
HI-Z
<2.0V
X
1
1
REF/N
B9b3: 1= ENTER TEST MODE, Default = 0 (NORMAL OPERATION)
B9b4: 1= REF/N, Default = 0 (HI-Z)
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
25
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
56-Lead, 300 mil Body, 25 mil, SSOP
SYMBOL
A
A1
b
c
D
E
E1
e
h
L
N
α
In Millimeters
COMMON DIMENSIONS
MIN
MAX
2.41
2.80
0.20
0.40
0.20
0.34
0.13
0.25
SEE VARIATIONS
10.03
10.68
7.40
7.60
0.635 BASIC
0.38
0.64
0.50
1.02
SEE VARIATIONS
0°
8°
In Inches
COMMON DIMENSIONS
MIN
MAX
.095
.110
.008
.016
.008
.0135
.005
.010
SEE VARIATIONS
.395
.420
.291
.299
0.025 BASIC
.015
.025
.020
.040
SEE VARIATIONS
0°
8°
VARIATIONS
N
56
D (inch)
D mm.
MIN
18.31
MAX
18.55
MIN
.720
MAX
.730
Reference Doc.: JEDEC Publication 95, MO-118
10-0034
Ordering Information
9LPRS502yFLFT
Example:
XXXX y F LF T
Designation for tape and reel packaging
Lead Free, RoHS Compliant (Optional)
Package Type
F = SSOP
Revision Designator (will not correlate with datasheet revision)
Device Type
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
26
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
c
N
56-Lead 6.10 mm. Body, 0.50 mm. Pitch TSSOP
(240 mil)
(20 mil)
In Millimeters
In Inches
SYMBOL COMMON DIMENSIONS COMMON DIMENSIONS
MIN
MAX
MIN
MAX
A
-1.20
-.047
A1
0.05
0.15
.002
.006
A2
0.80
1.05
.032
.041
b
0.17
0.27
.007
.011
c
0.09
0.20
.0035
.008
D
SEE VARIATIONS
SEE VARIATIONS
E
8.10 BASIC
0.319 BASIC
E1
6.00
6.20
.236
.244
e
0.50 BASIC
0.020 BASIC
L
0.45
0.75
.018
.030
N
SEE VARIATIONS
SEE VARIATIONS
α
0°
8°
0°
8°
aaa
-0.10
-.004
L
E1
INDEX
AREA
E
1 2
a
D
A
A2
A1
-Ce
VARIATIONS
SEATING
PLANE
b
N
aaa C
56
D mm.
MIN
MAX
13.90
14.10
D (inch)
MIN
.547
MAX
.555
Ref erence Doc.: JEDEC Publicat ion 95, M O-153
10-0039
Ordering Information
9LPRS502yGLFT
Example:
XXXX y G LF T
Designation for tape and reel packaging
Lead Free, RoHS Compliant
Package Type
G = TSSOP
Revision Designator (will not correlate with datasheet revision)
Device Type
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
27
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Advance Information
(Ref. )
Seating Plane
(N D - 1)x e
(Ref. )
A1
Index Area
A3
N
L
N
Anvil
Singulation
1
(Ref. )
b
(Ref.)
A
D
(N E - 1)x e
E2
2
Sawn
Singulation
Top View
e (Typ.)
2 If N D & N
E
are Even
1
2
E2
OR
E
ND & NE
Even
e
D2
2
ND & NE
Odd
Thermal
Base
D2
Chamfer 4x
0.6 x 0.6 max
OPTIONAL
C
0.08
C
THERMALLY ENHANCED, VERY THIN, FINE PITCH
QUAD FLAT / NO LEAD PLASTIC PACKAGE
DIMENSIONS
SYMBOL
A
A1
A3
b
e
DIMENSIONS
MIN.
MAX.
0.8
1.0
0
0.05
0.25 Reference
0.18
0.3
0.50 BASIC
SYMBOL
N
ND
NE
D x E BASIC
D2 MIN. / MAX.
E2 MIN. / MAX.
L MIN. / MAX.
Ordering Information
ICS 56L
TOLERANCE
56
14
14
8.00 x 8.00
4.35 / 4.65
5.05 / 5.35
0.30 / 0.50
9LPRS502yKLFT
Example:
XXXX y K LF T
Designation for tape and reel packaging
Lead Free, RoHS Compliant
Package Type
K = MLF
Revision Designator (will not correlate with datasheet revision)
Device Type
IDTTM/ICSTM 56-pin CK505 w/Fully Integrated Voltage Regulator + Integrated Series Resistor
28
1125E—02/26/09
ICS9LPRS502
56-PIN CK505 W/FULLY INTEGRATED VOLTAGE REGULATOR + INTEGRATED SERIES RESISTOR
Revision History
Rev.
A
B
C
D
E
Issue Date Description
1. Updated PLL3 Configuration Table.
2/19/2008 2. Release to Final.
4/25/2008 Updated Note on Byte 63
1. Updated Electrical Table.
9/3/2008 2. Udpated SMBus Byte 9.
2/23/2009 Updated Note under Byte 63 table.
2/26/2009 Updated Byte 8 table.
Page #
24
12,
21
24
21
This product is protected by United States Patent NO. 7,342,420 and other patents.
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
TM
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
408-284-6578
[email protected]
Corporate Headquarters
Asia Pacific and Japan
Europe
Integrated Device Technology, Inc.
6024 Silver Creek Valley Road
San Jose, CA 95138
United States
800 345 7015
+408 284 8200 (outside U.S.)
Integrated Device Technology
Singapore (1997) Pte. Ltd.
Reg. No. 199707558G
435 Orchard Road
#20-03 Wisma Atria
Singapore 238877
+65 6 887 5505
IDT Europe, Limited
Prime House
Barnett Wood Lane
Leatherhead, Surrey
United Kingdom KT22 7DE
+44 1372 363 339
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated
Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks
or registered trademarks used to identify products or services of their respective owners.
Printed in USA
29