TI1 DRV8837 Low-voltage h-bridge driver Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
DRV883x Low-Voltage H-Bridge Driver
1 Features
3 Description
•
The DRV883x provides an integrated motor driver
solution for cameras, consumer products, toys, and
other low-voltage or battery-powered motion control
applications. The device can drive one DC motor or
other devices like solenoids. The output driver block
consists of N-channel power MOSFET’s configured
as an H-bridge to drive the motor winding. An internal
charge pump generates needed gate drive voltages.
1
•
•
•
•
•
•
H-Bridge Motor Driver
– Drives a DC Motor or Other Loads
– Low MOSFET On-resistance: HS + LS
280 mΩ
1.8-A Maximum Drive Current
Separate Motor and Logic Supply Pins:
– Motor VM: 0 to 11 V
– Logic VCC: 1.8 to 7 V
PWM or PH/EN Interface
– DRV8837: PWM, IN1/IN2
– DRV8838: PH/EN
Low-power Sleep Mode With 120-nA Maximum
Sleep Current
– nSLEEP pin
Small Package and Footprint
– 8 WSON (PowerPAD™)
– 2.0 × 2.0 mm
Protection Features
– VCC Undervoltage Lockout (UVLO)
– Overcurrent Protection (OCP)
– Thermal Shutdown (TSD)
The DRV883x can supply up to 1.8 A of output
current. It operates on a motor power supply voltage
from 0 to 11 V, and a device power supply voltage of
1.8 V to 7.0 V.
The DRV8837 has a PWM (IN/IN) input interface; the
DRV8837 has a PH/EN input interface. Both
interfaces are compatible with industry-standard
devices.
Internal shutdown functions are provided for
overcurrent protection, short circuit protection,
undervoltage lockout, and overtemperature.
Device Information
ORDER NUMBER
PACKAGE
BODY SIZE
DRV8837DSGR
WSON (8)
2.0 × 2.0 mm
DRV8838DSGR
WSON (8)
2.0 × 2.0 mm
2 Applications
•
•
•
•
•
•
Cameras
DSLR Lenses
Consumer Products
Toys
Robotics
Medical Devices
DRV883x
1.8 to 7 V
PWM
VCC
or
PH and EN
Controller
0 to 11 V
nSLEEP
VM
DRV8837
and
DRV8838
Brushed DC
Motor Driver
1.8 A
M
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features .................................................................
Applications ..........................................................
Description ............................................................
Revision History ...................................................
Terminal Configuration and Functions ...............
Specifications ........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
4
5
6
8
Absolute Maximum Ratings .....................................
Handling Ratings ......................................................
Recommended Operating Conditions ......................
Thermal Information .................................................
Electrical Characteristics ..........................................
Timing Requirements ...............................................
Typical Characteristics .............................................
Detailed Description ............................................. 9
7.1 Overview .................................................................. 9
7.2 Functional Block Diagram ........................................ 9
7.3 Feature Description ................................................ 11
7.4 Device Functional Modes ....................................... 12
8
Applications and Implementation ..................... 13
8.1 Application Information .......................................... 13
8.2 Typical Applications ............................................... 13
9 Power Supply Recommendations ..................... 15
10 Layout ................................................................. 16
10.1 Layout Guidelines ................................................ 16
10.2 Layout Example ................................................... 16
11 Device and Documentation Support ................ 17
11.1
11.2
11.3
11.4
Related Links .......................................................
Trademarks ..........................................................
Electrostatic Discharge Caution ...........................
Glossary ...............................................................
17
17
17
17
12 Mechanical, Packaging, and Orderable
Information .......................................................... 18
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (December 2013) to Revision C
Page
•
Added the DRV8838 device information, specifications, and timing diagrams ..................................................................... 1
•
Added Device Information table ............................................................................................................................................ 1
•
Added a PWM Interface diagram .......................................................................................................................................... 1
•
Added more information to the Detailed Description and moved information from the Functional Description .................... 9
•
Added functional block diagram for DRV8838 .................................................................................................................... 10
•
Added the Applications and Implementation section ........................................................................................................... 13
•
Added Power Supply Recommendations, Layout, Device and Documentation Support, and Packaging sections ............ 15
Changes from Revision A (August 2012) to Revision B
Page
•
Changed Features section .................................................................................................................................................... 1
•
Changed Recommended Operating Conditions .................................................................................................................... 4
•
Changed Electrical Characteristics section ........................................................................................................................... 5
•
Changed Timing Requirements section ................................................................................................................................ 6
•
Changed Power Supplies and Input Pins section ............................................................................................................... 11
2
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
5 Terminal Configuration and Functions
DRV8837 DSG – WSON
(Top View)
VM
OUT1
OUT2
GND
1
2
3
8
GND
(PPAD)
4
7
6
5
VCC
nSLEEP
IN1
IN2
DRV8838 DSG – WSON
(Top View)
VM
OUT1
OUT2
GND
1
2
3
8
GND
(PPAD)
4
7
6
5
VCC
nSLEEP
PH
EN
Terminal Descriptions
TERMINAL
NAME
NUMBER
TYPE
DESCRIPTION
POWER AND GROUND
GND
4
PWR
Device ground
Must be connected to ground
VCC
8
PWR
Logic Power supply
Bypass to GND with a 0.1-µF ceramic capacitor rated for VCC
VM
1
PWR
Motor power supply
Bypass to GND with a 0.1-µF ceramic capacitor rated for VM
IN1/PH
6
I
IN1 or PHASE input
See Detailed Description for more information
IN2/EN
5
I
IN2 or ENABLE input
nSLEEP
7
I
Sleep mode input
Logic low puts the device in low-power sleep mode; logic high for normal operation; internal
pulldown resistor
OUT1
2
O
OUT2
3
O
CONTROL
OUTPUT
Motor output
Connect to motor winding
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
3
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
Motor power supply voltage range (VM)
–0.3
12
V
Logic power supply voltage range (VCC)
–0.3
7
V
Control pin voltage range (IN1, IN2, PH, EN, nSLEEP)
–0.5
7
V
Peak drive current (OUT1, OUT2)
Internally limited
TJ, operating virtual junction temperature range
(1)
(2)
–40
UNIT
A
150
ºC
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
6.2 Handling Ratings
over operating free-air temperature range (unless otherwise noted)
Tstg
Storage temperature range
MIN
MAX
UNIT
–60
150
ºC
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
VM
Motor power supply voltage range
0
11
V
VCC
Logic power supply voltage range
1.8
7
V
IOUT
Motor peak current
0
1.8
A
fPWM
Externally applied PWM frequency
0
250
kHz
VLOGIC
Logic level input voltage
0
5.5
V
TA
Operating ambient temperature
–40
85
°C
(1)
UNIT
Power dissipation and thermal limits must be observed.
6.4 Thermal Information
over operating free-air temperature range (unless otherwise noted)
DRV8837, DRV8838
THERMAL METRIC (1)
WSON (8 TERMINALS)
Junction-to-ambient thermal resistance (2)
ΘJA
60.9
(3)
ΘJC(TOP)
Junction-to-case (top) thermal resistance
ΘJB
Junction-to-board thermal resistance (4)
32.2
ΨJT
Junction-to-top characterization parameter (5)
1.6
ΨJB
Junction-to-board characterization parameter (6)
32.8
ΘJC(BOTTOM) Junction-to-case (bottom) thermal resistance (7)
9.8
(1)
(2)
(3)
(4)
(5)
(6)
(7)
4
UNIT
71.4
°C/W
For more information about traditional and new thermal limits, see the IC Package Thermal Metrics Report, SPRA953.
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
6.5 Electrical Characteristics
TA = 25°C, over recommended operating conditions unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
POWER SUPPLIES (VM, VCC)
VM
IVM
VM operating voltage
VM operating supply current
IVMQ
VM sleep mode supply current
VCC
VCC operating voltage
IVCC
IVCCQ
VCC operating supply current
VCC sleep mode supply current
0
11
V
40
100
μA
VM = 5 V; VCC = 3 V;
50 kHz PWM
0.8
1.5
mA
VM = 5 V; VCC = 3 V;
nSLEEP = 0
30
95
nA
7
V
VM = 5 V; VCC = 3 V;
No PWM
1.8
VM = 5 V; VCC = 3 V;
No PWM
300
500
μA
VM = 5 V; VCC = 3 V;
50 kHz PWM
0.7
1.5
mA
VM = 5 V; VCC = 3 V;
nSLEEP = 0
5
25
nA
CONTROL INPUTS (IN1/PH, IN2/EN, nSLEEP)
VIL
Input logic low voltage
VIH
Input logic high voltage
VHYS
Input logic hysteresis
IIL
Input logic low current
IIH
RPD
Input logic high current
Pulldown resistance
0.25 × VCC
0.38 × VCC
0.46 × VCC
V
0.5 × VCC
0.08 × VCC
VIN = 0 V
–5
VIN = 3.3 V
V
mV
5
μA
50
μA
60
μA
100
kΩ
DRV8838 nSLEEP pin
55
kΩ
280
VIN = 3.3 V, DRV8838 nSLEEP pin
MOTOR DRIVER OUTPUTS (OUT1, OUT2)
RDS(ON)
HS + LS FET on-resistance
VM = 5 V; VCC = 3 V;
IO = 800 mA; TJ = 25°C
IOFF
Off-state leakage current
VOUT = 0 V
330
mΩ
200
nA
VCC falling
1.7
V
VCC rising
1.8
–200
PROTECTION CIRCUITS
VUVLO
VCC undervoltage lockout
IOCP
Overcurrent protection trip level
tDEG
Overcurrent deglitch time
1
μs
tRETRY
Overcurrent retry time
1
ms
TTSD
Thermal shutdown temperature
1.9
Die temperature TJ
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
150
3.5
160
180
Submit Documentation Feedback
A
°C
5
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
6.6 Timing Requirements
TA = 25°C, VM = 5 V, VCC = 3 V, RL = 20 Ω
NUMBER
PARAMETER
1
t1
2
t2
3
MAX
UNIT
Delay time, PHASE high to OUT1 low
160
ns
Delay time, PHASE high to OUT2 high
200
ns
t3
Delay time, PHASE low to OUT1 high
200
ns
4
t4
Delay time, PHASE low to OUT2 low
160
ns
5
t5
Delay time, ENBL high to OUTx high
200
ns
6
t6
Delay time, ENBL low to OUTx low
160
ns
7
t7
Output enable time
300
ns
8
t8
Output disable time
300
ns
9
t9
Delay time, INx high to OUTx high
160
ns
10
t10
Delay time, INx low to OUTx low
160
ns
11
t11
Output rise time
30
188
ns
12
t12
Output fall time
30
188
ns
30
μs
twake
TEST CONDITIONS
MIN
Wake time, nSLEEP rising edge to part active
xENBL
xPHASE
3
5
xOUT1
1
6
5
6
4
2
xOUT2
DRV8838
Figure 1. Input and Output Timing for DRV8838
6
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
IN1
IN2
7
10
8
zz
zz
OUT1
9
zz
OUT2
zz
DRV8837
80%
80%
OUTx
20%
11
20%
12
Figure 2. Input and Output Timing for DRV8837
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
7
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
6.7 Typical Characteristics
Plot generated using characterization data
700
650
H S + LS R D S (O N ) (m : )
600
550
VM = 2 V, VCC = 2 V
VM = 5 V, VCC = 3 V
VM = 11 V, VCC = 5.5 V
500
450
400
350
300
250
200
-40
-20
0
20
40
T A (qC)
60
80
100
D001
Figure 3. HS + LS RDS(ON) vs TA
8
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
7 Detailed Description
7.1 Overview
The DRV883x is a H-bridge driver that can drive one DC motor or other devices like solenoids. The outputs are
controlled using either a PWM interface (IN1/IN2) on the DRV8837 or a PH/EN interface on the DRV8838.
A low-power sleep mode is included, which can be enabled using the nSLEEP pin.
These devices greatly reduce the component count of motor driver systems by integrating the necessary driver
FETs and FET control circuitry into a single device. In addition, the DRV883x adds protection features above
traditional discrete implementations: undervoltage lockout, overcurrent protection, and thermal shutdown.
7.2 Functional Block Diagram
0 to 11 V
VM
VM
VM
Gate
Drive
Charge
Pump
OUT1
OCP
1.8 to 7 V
VCC
DCM
VM
VCC
Logic
Gate
Drive
OUT2
OCP
IN1
IN2
OverTemp
Osc
nSLEEP
GND
B0479-01
Figure 4. DRV8837 Functional Block Diagram
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
9
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
Functional Block Diagram (continued)
0 to 11 V
VM
VM
VM
Gate
Drive
Charge
Pump
OUT1
OCP
1.8 to 7 V
VCC
DCM
VM
VCC
Logic
Gate
Drive
OUT2
OCP
PH
EN
OverTemp
Osc
nSLEEP
GND
B0479-01
Figure 5. DRV8838 Functional Block Diagram
10
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
7.3 Feature Description
7.3.1 Bridge Control
The DRV8837 is controlled using a PWM input interface, also called an IN/IN interface. Each output is controlled
by a corresponding input pin.
Table 1 shows the logic for the DRV8837 device:
Table 1. DRV8837 Device Logic
nSLEEP
IN1
IN2
OUT1
OUT2
Function (DC Motor)
0
X
X
Z
Z
Coast
1
0
0
Z
Z
Coast
1
0
1
L
H
Reverse
1
1
0
H
L
Forward
1
1
1
L
L
Brake
The DRV8838 is controlled using a PHASE/ENABLE interface. This interface uses one pin to control the Hbridge current direction, and one pin to enable or disable the H-bridge.
Table 2 shows the logic for the DRV8838:
Table 2. DRV8838 Device Logic
nSLEEP
PH
EN
OUT1
OUT2
Function (DC Motor)
0
X
X
Z
Z
Coast
1
X
0
L
L
Brake
1
1
1
L
H
Reverse
1
0
1
H
L
Forward
7.3.2 Sleep Mode
If the nSLEEP pin is brought to a logic-low state, the DRV883x enters a low-power sleep mode. In this state, all
unnecessary internal circuitry is powered down.
7.3.3 Power Supplies and Input Terminals
The input pins may be driven within their recommended operating conditions with or without the VCC and/or VM
power supplies present. No leakage current path will exist to the supply. There is a weak pulldown resistor
(approximately 100 kΩ) to ground on each input pin.
VCC and VM may be applied and removed in any order. When VCC is removed, the device will enter a low
power state and draw very little current from VM. VCC and VM may be connected together if the supply voltage
is between 1.8 and 7 V.
The VM voltage supply does not have any undervoltage lockout protection (UVLO), so as long as VCC > 1.8 V;
the internal device logic will remain active. This means that the VM pin voltage may drop to 0 V, however, the
load may not be sufficiently driven at low VM voltages.
7.3.4 Protection Circuits
The DRV883x is fully protected against VCC undervoltage, overcurrent, and overtemperature events.
VCC Undervoltage Lockout: If at any time the voltage on the VCC pin falls below the undervoltage lockout
threshold voltage, all FETs in the H-bridge will be disabled. Operation resumes when VCC rises above the UVLO
threshold.
Overcurrent Protection (OCP): An analog current limit circuit on each FET limits the current through the FET by
removing the gate drive. If this analog current limit persists for longer than tDEG, all FETs in the H-bridge will be
disabled. Operation resumes automatically after tRETRY has elapsed. Overcurrent conditions will be detected on
both the high-side and low-side devices. A short to VM, GND, or from OUT1 to OUT2 results in an overcurrent
condition
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
11
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
Thermal Shutdown (TSD): If the die temperature exceeds safe limits, all FETs in the H-bridge will be disabled.
After the die temperature falls to a safe level, operation automatically resumes.
Table 3. Fault Behavior
Fault
Condition
H-bridge
Recovery
VCC undervoltage (UVLO)
VCC < 1.7 V
Disabled
VCC > 1.8 V
Overcurrent (OCP)
IOUT > 1.9 A (MIN)
Disabled
tRETRY elapses
Thermal Shutdown (TSD)
TJ > 150°C (MIN)
Disabled
TJ < 150°C
7.4 Device Functional Modes
The DRV883x is active unless the nSLEEP pin is brought logic low. In sleep mode the H-bridge FETs are
disabled Hi-Z. The DRV883x is brought out of sleep mode automatically if nSLEEP is brought logic high.
The H-bridge outputs are disabled during undervoltage lockout, overcurrent, and overtemperature fault
conditions.
Table 4. Operation Modes
12
Mode
Condition
H-bridge
Operating
nSLEEP pin = 1
Operating
Sleep mode
nSLEEP pin = 0
Disabled
Fault encountered
Any fault condition met
Disabled
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
8 Applications and Implementation
8.1 Application Information
The DRV883x is device is used to drive one DC motor or other devices like solenoids. The following design
procedure can be used to configure the DRV883x.
8.2 Typical Applications
DRV8837 and
DRV8838
VM
1
0.1 µF
VM
2
VCC
0.1 µF
7
OUT1
nSLEEP
OUT2
IN1/PH
6
4
GND
PAD
3
M
8
VCC
5
IN2/EN
Figure 6. Schematic of DRV883x Application
8.2.1 Design Requirements
Table 5 shows required parameters for a typical usage case.
Table 5. System Design Requirements
Reference
Example Value
Motor supply voltage
Design Parameter
VM
9V
Logic supply voltage
VCC
3.3 V
Target RMS current
IOUT
0.8 A
8.2.2 Detailed Design Procedure
8.2.2.1 Power Dissipation
Power dissipation in the DRV883x is dominated by the power dissipated in the output FET resistance, or RDS(ON).
Average power dissipation when running a stepper motor can be roughly estimated by:
PTOT = RDS(ON) ´ (IOUT(RMS) )2
where
•
•
•
PTOT is the total power dissipation
RDS(ON) is the resistance of the HS plus LS FETs
IOUT(RMS) is the RMS or DC output current being supplied to the load
(1)
The maximum amount of power that can be dissipated in the device is dependent on ambient temperature and
heatsinking.
Note that RDS(ON) increases with temperature, so as the device heats, the power dissipation increases.
The DRV883x has thermal shutdown protection. If the die temperature exceeds approximately 150°C, the device
will be disabled until the temperature drops to a safe level.
Any tendency of the device to enter thermal shutdown is an indication of either excessive power dissipation,
insufficient heatsinking, or too high an ambient temperature.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
13
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
8.2.3 Application Performance Plots
14
Figure 7. 50% Duty Cycle, Forward Direction
Figure 8. 50% Duty Cycle, Reverse Direction
Figure 9. 20% Duty Cycle, Forward Direction
Figure 10. 20% Duty Cycle, Reverse Direction
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
9 Power Supply Recommendations
VCC and VM may be applied and removed in any order. When VCC is removed, the device enters a low power
state and draws very little current from VM. VCC and VM may be connected together if the supply voltage is
between 1.8 and 7 V.
Bypass VM and VCC with 0.1-µF ceramic capacitors rated for VM and VCC. Place these capacitors as close to
the device as possible.
The VM voltage supply does not have any undervoltage lockout protection, so as long as VCC > 1.8 V; the
internal device logic will remain active. This means that the VM pin voltage may drop to 0 V; however, the load
may not be sufficiently driven at low VM voltages.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
15
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
10 Layout
10.1 Layout Guidelines
The VM and VCC terminals should be bypassed to GND using low-ESR ceramic bypass capacitors with a
recommended value of 0.1 µF rated for VM and VCC. These capacitors should be placed as close to the VM and
VCC pins as possible with a thick trace or ground plane connection to the device GND pin.
10.2 Layout Example
0.1 µF
0.1 µF
VM
VCC
OUT1
nSLEEP
OUT2
IN1/PH
GND
IN2/EN
Figure 11. Simplified Layout Example
16
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
DRV8837, DRV8838
www.ti.com
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
11 Device and Documentation Support
11.1 Related Links
The following table lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 6. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
DRV8837
Click here
Click here
Click here
Click here
Click here
DRV8838
Click here
Click here
Click here
Click here
Click here
11.2 Trademarks
PowerPAD is a trademark of Texas Instruments.
11.3 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms and definitions.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
Submit Documentation Feedback
17
DRV8837, DRV8838
SLVSBA4C – JUNE 2012 – REVISED FEBRUARY 2014
www.ti.com
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DRV8837 DRV8838
PACKAGE OPTION ADDENDUM
www.ti.com
17-May-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DRV8837DSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | Call TI
Level-2-260C-1 YEAR
-40 to 85
837
DRV8837DSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
837
DRV8838DSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
838
DRV8838DSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
838
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
17-May-2014
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
13-Mar-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
DRV8837DSGR
WSON
DSG
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
180.0
8.4
2.3
2.3
1.15
4.0
8.0
Q2
DRV8837DSGT
WSON
DSG
8
250
180.0
8.4
2.3
2.3
1.15
4.0
8.0
Q2
DRV8838DSGR
WSON
DSG
8
3000
180.0
8.4
2.3
2.3
1.15
4.0
8.0
Q2
DRV8838DSGT
WSON
DSG
8
250
180.0
8.4
2.3
2.3
1.15
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
13-Mar-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DRV8837DSGR
WSON
DSG
8
3000
210.0
185.0
35.0
DRV8837DSGT
WSON
DSG
8
250
210.0
185.0
35.0
DRV8838DSGR
WSON
DSG
8
3000
210.0
185.0
35.0
DRV8838DSGT
WSON
DSG
8
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated