ASM3P2579A August 2005 rev 1.0 Low Power Peak EMI Reducing Solution Features The ASM3P2579A uses the most efficient and optimized modulation profile approved by the FCC and is Generates an EMI optimized clock signal at the implemented by using a proprietary all digital method. output. Integrated loop filter components. Operates with a 3.3 / 2.5V Supply. Operating current less than 4mA. Low power CMOS design. Input frequency range: 12MHz to 30MHz for 2.5V The ASM3P2579A modulates the output of a single PLL in order to “spread” the bandwidth of a synthesized clock, and more importantly, decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced : 12MHz to 30MHz for 3.3V by oscillators and most frequency generators. Lowering Generates a 1X low EMI spread spectrum clock of EMI by increasing a signal’s bandwidth is called ‘spread the input frequency. spectrum clock generation’. Spread Spectrum Enable Control. Frequency deviation: ±1% @ 24MHz Available in 6 pin TSOT-23, 8 pin SOIC and 8 pin Applications TSSOP Packages. The ASM3P2579A is targeted towards all portable devices with very low power requirements like MP3 Product Description players and digital still cameras. The ASM3P2579A is a versatile spread spectrum Key Specifications frequency modulator designed specifically for a wide range of clock frequencies. The ASM3P2579A reduces Description electromagnetic interference (EMI) at the clock source, Specification Supply voltages VDD = 3.3V/2.5V dependent signals. The ASM3P2579A allows significant Cycle-to-Cycle Jitter 200pS (Max) system cost savings by reducing the number of circuit Output Duty Cycle 45/55% (worst case) board layers ferrite beads, shielding that are traditionally Modulation Rate Equation FIN/640 required to pass EMI regulations. Frequency Deviation ±1% @ 24MHz allowing system wide reduction of EMI of Block Diagram all clock VDD SSON XOUT PLL Modulation XIN Crystal Oscillator Frequency Divider Feedback Divider Phase Detector Loop Filter VCO Output Divider ModOUT VSS Alliance Semiconductor 2575 Augustine Drive • Santa Clara, CA • Tel: 408.855.4900 • Fax: 408.855.4999 • www.alsc.com Notice: The information in this document is subject to change without notice. ASM3P2579A August 2005 rev 1.0 Pin Configuration (6-pin TSOT-23 Package) SSON 1 XOUT 2 XIN/CLKIN 3 ASM3P2579A 6 VSS 5 ModOUT 4 VDD Pin Description Pin# Pin Name Type Description 1 SSON I When SSON is HIGH, the spread spectrum is enabled and when LOW, it turns off the spread spectrum. Connect the pin to ground When Spread Spectrum feature is not required. 2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected. 3 XIN/CLKIN I Crystal connection or external reference frequency input. This pin has dual functions. It can be connected either to an external crystal or an external reference clock. 4 VDD P Power supply for the entire chip 5 ModOUT O Spread spectrum clock output. 6 VSS P Ground connection. Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 2 of 12 ASM3P2579A August 2005 rev 1.0 Pin Configuration (8-pin SOIC and TSSOP Packages) XIN/CLKIN 1 8 VDD XOUT 2 7 NC SSON 3 6 ModOUT NC 4 5 VSS ASM3P2579A Pin Description Pin# Pin Name Type 1 XIN/CLKIN I Crystal connection or external reference frequency input. This pin has dual functions. It can be connected either to an external crystal or an external reference clock. 2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected. I When SSON is HIGH, the spread spectrum is enabled and when LOW, it turns off the spread spectrum. Connect the pin to ground When Spread Spectrum feature is not required. 3 SSON Description 4 NC - No connect. 5 VSS P Ground connection. 6 ModOUT O Spread spectrum clock output. 7 NC - No connect. 8 VDD P Power supply for the entire chip Modulation Profile Specifications Description Specification Frequency Range 12MHz < CLKIN < 30MHz Modulation Equation FIN/640 Frequency Deviation ±1% @ 24MHz Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 3 of 12 ASM3P2579A August 2005 rev 1.0 Absolute Maximum Ratings Symbol VDD, VIN TSTG Parameter Rating Unit Voltage on any pin with respect to Ground -0.5 to +7.0 V Storage temperature -65 to +125 °C 0 to 70 °C TA Operating temperature Ts Max. Soldering Temperature (10 sec) 260 °C TJ Junction Temperature 150 °C 2 KV TDV Static Discharge Voltage (As per JEDEC STD22- A114-B) Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. DC Electrical Characteristics for 2.5V Supply (Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated) Symbol Min Typ Max Unit VIL Input low voltage Parameter VSS - 0.3 - 0.8 V VIH Input high voltage 2.0 - VDD + 0.3 V IIL Input low current - - -35 µA IIH Input high current - - 35 µA IXOL XOUT output low current (@0.5V, VDD=2.5V) - 3 - mA IXOH XOUT output high current (@1.8V, VDD=2.5V) - 3 - mA VOL Output low voltage (VDD = 2.5 V, IOL = 8mA) - - 0.6 V VOH Output high voltage (VDD = 2.5 V, IOH = 8mA) 1.8 - - V IDD Static supply current * - 1.1 - mA ICC VDD tON ZOUT Dynamic supply current (2.5V, 24MHz and no load) - 3.5 - mA 2.375 2.5 2.625 V Power-up time (first locked cycle after power-up) - - 5 mS Output impedance - 50 - Ω Operating Voltage * XIN/CLKIN is made low. AC Electrical Characteristics for 2.5V Supply Symbol Parameter Min Typ Max Unit CLKIN Input frequency 12 - 30 MHz ModOUT Output frequency 12 - 30 MHz fd Frequency Deviation Input Frequency = 12MHz - - ±1.65 Input Frequency = 30MHz - - ±0.80 tLH* Output rise time (measured from 0.7V to 1.7V) 0.7 1.5 1.9 nS tHL* Output fall time (measured from 1.7V to 0.7V) 0.4 1.0 1.1 nS tJC Jitter (cycle to cycle) - - 200 pS tD Output duty cycle 45 50 55 % % * tLH and tHL are measured into a capacitive load of 15pF Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 4 of 12 ASM3P2579A August 2005 rev 1.0 DC Electrical Characteristics for 3.3V Supply (Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated) Symbol Parameter Min Typ Max Unit VIL Input low voltage VSS - 0.3 - 0.8 V VIH Input high voltage 2.0 - VDD + 0.3 V IIL Input low current - - -35 µA IIH Input high current - - 35 µA IXOL XOUT output low current (@0.4V, VDD=3.3V) - 3 - mA IXOH XOUT output high current (@2.5V, VDD=3.3V) - 3 - mA VOL Output low voltage (VDD = 3.3 V, IOL = 8mA) - - 0.4 V VOH Output high voltage (VDD = 3.3 V, IOH = 8mA) 2.5 - - V IDD Static supply current* - 1.2 - mA ICC VDD tON ZOUT Dynamic supply current (3.3V, 24MHz and no load) - 4.0 - mA 2.7 3.3 3.6 V Power-up time (first locked cycle after power-up) - - 5 mS Output impedance - 45 - Ω Operating Voltage * XIN/CLKIN is made low. AC Electrical Characteristics for 3.3V Supply Symbol Parameter Min Typ Max Unit CLKIN Input frequency 12 - 30 MHz ModOUT Output frequency 12 - 30 MHz fd Frequency Deviation Input Frequency = 12MHz - - ±1.65 Input Frequency = 30MHz - - ±0.80 tLH* Output rise time (measured from 0.8 to 2.0V) 0.5 1.4 1.7 nS tHL* Output fall time (measured at 2.0V to 0.8V) 0.4 1.0 1.2 nS tJC Jitter (cycle to cycle) - - 200 pS tD Output duty cycle 45 50 55 % % *tLH and tHL are measured into a capacitive load of 15pF Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 5 of 12 ASM3P2579A August 2005 rev 1.0 Typical Crystal Oscillator Circuit R1 = 510Ω Crystal C1 = 27 pF C2 = 27 pF Typical Crystal Specifications Fundamental AT cut parallel resonant crystal Nominal frequency 14.31818MHz Frequency tolerance ± 50 ppm or better at 25°C Operating temperature range -25°C to +85°C Storage temperature -40°C to +85°C Load capacitance 18pF Shunt capacitance 7pF maximum ESR 25Ω Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 6 of 12 ASM3P2579A August 2005 rev 1.0 Package Information 6-pin TSOT-23 Package Dimensions Symbol Inches Min A Max Millimeters Min Max 0.04 1.00 A1 0.00 0.004 0.00 0.10 A2 0.033 0.036 0.84 0.90 b 0.012 0.02 0.30 0.50 H 0.005 BSC 0.127 BSC D 0.114 BSC 2.90 BSC B 0.06 BSC 1.60 BSC e 0.0374 BSC 0.950 BSC C 0.11 BSC 2.80 BSC L 0.0118 0.02 0.30 0.50 θ 0° 4° 0° 4° Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 7 of 12 ASM3P2579A August 2005 rev 1.0 8-Pin SOIC Package H E D A2 A C A1 D θ e L B Dimensions Symbol Inches Min Max Millimeters Min Max A1 0.004 0.010 0.10 0.25 A 0.053 0.069 1.35 1.75 A2 0.049 0.059 1.25 1.50 B 0.012 0.020 0.31 0.51 C 0.007 0.010 0.18 0.25 D 0.193 BSC 4.90 BSC E 0.154 BSC 3.91 BSC e 0.050 BSC 1.27 BSC H 0.236 BSC 6.00 BSC L 0.016 0.050 0.41 1.27 θ 0° 8° 0° 8° Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 8 of 12 ASM3P2579A August 2005 rev 1.0 8-Pin TSSOP Package H E D A2 A C θ e A1 L B Dimensions Symbol Inches Min Millimeters Max A Min Max 0.043 1.10 A1 0.002 0.006 0.05 0.15 A2 0.033 0.037 0.85 0.95 B 0.008 0.012 0.19 0.30 c 0.004 0.008 0.09 0.20 D 0.114 0.122 2.90 3.10 E 0.169 0.177 4.30 4.50 e 0.026 BSC 0.65 BSC H 0.252 BSC 6.40 BSC L 0.020 0.028 0.50 0.70 θ 0° 8° 0° 8° Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 9 of 12 ASM3P2579A August 2005 rev 1.0 Ordering Information Part Number Marking ASM3P2579AF-06OR S4LL ASM3P2579AF-08TT Package Type Temperature 6-Pin TSOT-23, TAPE & REEL, Pb Free Commercial 3P2579AF 8-Pin TSSOP, TUBE, Pb Free Commercial ASM3P2579AF-08TR 3P2579AF 8-Pin TSSOP, TAPE & REEL, Pb Free Commercial ASM3P2579AF-08ST 3P2579AF 8-Pin SOIC, TUBE, Pb Free Commercial ASM3P2579AF-08SR 3P2579AF 8-Pin SOIC, TAPE & REEL, Pb Free Commercial ASM3P2579A-06OR S1LL 6-Pin TSOT-23, TAPE & REEL Commercial ASM3P2579A-08TT 3P2579A 8-Pin TSSOP, TUBE Commercial ASM3P2579A-08TR 3P2579A 8-Pin TSSOP, TAPE & REEL Commercial ASM3P2579A-08ST 3P2579A 8-Pin SOIC, TUBE Commercial ASM3P2579A-08SR 3P2579A 8-Pin SOIC, TAPE & REEL Commercial 6-Pin TSOT-23, TAPE & REEL, Green Commercial ASM3P2579AG-06OR S3LL ASM3P2579AG-08TT 3P2579AG 8-Pin TSSOP, TUBE, Green Commercial ASM3P2579AG-08TR 3P2579AG 8-Pin TSSOP, TAPE & REEL, Green Commercial ASM3P2579AG-08ST 3P2579AG 8-Pin SOIC, TUBE, Green Commercial ASM3P2579AG-08SR 3P2579AG 8-Pin SOIC, TAPE & REEL, Green Commercial ASM3I2579AF-06OR S5LL ASM3I2579AF-08TT 6-Pin TSOT-23, TAPE & REEL, Pb Free Industrial 3I2579AF 8-Pin TSSOP, TUBE, Pb Free Industrial ASM3I2579AF-08TR 3I2579AF 8-Pin TSSOP, TAPE & REEL, Pb Free Industrial ASM3I2579AF-08ST 3I2579AF 8-Pin SOIC, TUBE, Pb Free Industrial ASM3I2579AF-08SR 3I2579AF 8-Pin SOIC, TAPE & REEL, Pb Free Industrial ASM3I2579A-06OR S2LL 6-Pin TSOT-23, TAPE & REEL Industrial ASM3I2579A-08TT 3I2579A 8-Pin TSSOP, TUBE Industrial ASM3I2579A-08TR 3I2579A 8-Pin TSSOP, TAPE & REEL Industrial ASM3I2579A-08ST 3I2579A 8-Pin SOIC, TUBE Industrial ASM3I2579A-08SR 3I2579A 8-Pin SOIC, TAPE & REEL Industrial 6-Pin TSOT-23, TAPE & REEL, Green Industrial ASM3I2579AG-06OR S6LL ASM3I2579AG-08TT 3I2579AG 8-Pin TSSOP, TUBE, Green Industrial ASM3I2579AG-08TR 3I2579AG 8-Pin TSSOP, TAPE & REEL, Green Industrial ASM3I2579AG-08ST 3I2579AG 8-Pin SOIC, TUBE, Green Industrial ASM3I2579AG-08SR 3I2579AG 8-Pin SOIC, TAPE & REEL, Green Industrial Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 10 of 12 ASM3P2579A August 2005 rev 1.0 Device Ordering Information A S M 3 P 2 5 7 9 A F - 0 8 T R R = Tape & reel, T = Tube or Tray O = SOT S = SOIC T = TSSOP A = SSOP V = TVSOP B = BGA Q = QFN U = MSOP E = TQFP L = LQFP U = MSOP P = PDIP D = QSOP X = SC-70 DEVICE PIN COUNT F = LEAD FREE AND RoHS COMPLIANT PART G = GREEN PACKAGE PART NUMBER X= Automotive I= Industrial P or n/c = Commercial (-40C to +125C) (-40C to +85C) (0C to +70C) 1 = Reserved 2 = Non PLL based 3 = EMI Reduction 4 = DDR support products 5 = STD Zero Delay Buffer 6 = Power Management 7 = Power Management 8 = Power Management 9 = Hi Performance 0 = Reserved ALLIANCE SEMICONDUCTOR MIXED SIGNAL PRODUCT Licensed under U.S Patent Nos 5,488,627 and 5,631,921 Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 11 of 12 ASM3P2579A August 2005 rev 1.0 Alliance Semiconductor Corporation 2575 Augustine Drive, Santa Clara, CA 95054 Tel# 408-855-4900 Fax: 408-855-4999 www.alsc.com Copyright © Alliance Semiconductor All Rights Reserved Preliminary Information Part Number: ASM3P2579A Document Version: v1.0 Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to Alliance Semiconductor, dated 11-11-2003 © Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use. Low Power Peak EMI Reducing Solution Notice: The information in this document is subject to change without notice. 12 of 12