TI LP2980IM5X-2.5 Lp2980-n micropower 50 ma ultra low-dropout regulator in sot-23 package Datasheet

LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
LP2980-N Micropower 50 mA Ultra Low-Dropout Regulator In SOT-23 Package
Check for Samples: LP2980-N
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
•
The LP2980-N is a 50 mA, fixed-output voltage
regulator designed specifically to meet the
requirements of battery-powered applications.
1
2
•
Ultra Low Dropout Voltage
Output Voltage Accuracy 0.5% (A Grade)
Ensured 50 mA Output Current
Requires Only 1 μF External Capacitance
< 1 μA Quiescent Current When Shutdown
Low Ground Pin Current at all Load Currents
High Peak Current Capability (150 mA Typical)
Wide Supply Voltage Range (16V Max)
Fast Dynamic Response to Line and Load
Low ZOUT Over Wide Frequency Range
Over-Temperature and Over-Current
Protection
−40°C to +125°C Junction Temperature Range
APPLICATIONS
•
•
•
•
Cellular Phone
Palmtop/Laptop Computer
Personal Digital Assistant (PDA)
Camcorder, Personal Stereo, Camera
Using an optimized VIP (Vertically Integrated PNP)
process,
the
LP2980-N
delivers
unequaled
performance in all specifications critical to batterypowered designs:
Dropout Voltage. Typically 120 mV @ 50 mA load,
and 7 mV @ 1 mA load.
Ground Pin Current. Typically 375 μA @ 50 mA
load, and 80 μA @ 1 mA load.
Sleep Mode. Less than 1 μA quiescent current when
ON/OFF pin is pulled low.
Minimum Part Count. Requires only 1 μF of external
capacitance on the regulator output.
Precision Output. 0.5% tolerance output voltages
available (A grade).
5.0V, 4.7V, 3.3V, 3.0V and 2.5V versions available as
standard products.
Block Diagram
Figure 1.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
Connection Diagram
Top View
Figure 2. 5-Lead SOT-23 Package
See Package Number DBV0005A
PIN DESCRIPTIONS
Name
Pin Number
Function
VIN
1
Input Voltage
GND
2
Common Ground (device substrate)
ON/OFF
3
Logic high enable input
N/C
4
Post package trim - do not connect to this pin
VOUT
5
Regulated output voltage
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
ABSOLUTE MAXIMUM RATINGS (1) (2)
−65°C to +150°C
Storage Temperature Range
Operating Junction Temperature
Lead Temperature
−40°C to +125°C
Range
(Soldering, 5 sec.)
260°C
ESD Rating (3)
Power Dissipation
2 kV
(4)
Internally Limited
−0.3V to +16V
Input Supply Voltage (Survival)
Input Supply Voltage (Operating)
2.1V to +16V
−0.3V to +16V
Shutdown Input Voltage (Survival)
Output Voltage (Survival) (5)
−0.3V to +9V
IOUT (Survival)
Short Circuit Protected
Input-Output Voltage (Survival) (6)
(1)
(2)
(3)
(4)
(5)
(6)
−0.3V to +16V
Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply
when operating the device outside of its rated operating conditions.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
The ESD rating of pins 3 and 4 for the SOT-23 package is 1 kV.
The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, θJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using:
The value of θJA for the SOT-23 package is 220°C/W. Exceeding the maximum allowable power dissipation will cause excessive die
temperature, and the regulator will go into thermal shutdown.
If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2980-N output must be diode-clamped
to ground.
The output PNP structure contains a diode between the VIN and VOUT terminals that is normally reverse-biased. Reversing the polarity
from VIN to VOUT will turn on this diode (See REVERSE CURRENT PATH).
ELECTRICAL CHARACTERISTICS
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2V.
Symbol
Parameter
Conditions
Typ
IL = 1 mA
ΔVO
Output Voltage Tolerance
Output Voltage Line
Regulation
VIN–VO
(1)
(2)
Dropout Voltage
1 mA < IL < 50 mA
VO(NOM) + 1V
≤ VIN ≤ 16V
LP2980AI-XX (1)
LP2980I-XX (1)
Min
Max
Min
Max
−0.50
0.50
−1.0
1.0
−0.75
0.75
−1.5
1.5
−2.5
2.5
−3.5
3.5
0.007
0.014
0.032
0.014
0.032
IL = 0
1
3
5
3
5
IL = 1 mA
7
10
15
10
15
IL = 10 mA
40
60
90
60
90
IL = 50 mA
120
150
225
150
225
(2)
Units
%VNOM
%/V
mV
Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical
Quality Control (SQC) methods. The limits are used to calculate Average Outgoing Quality Level (AOQL).
Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a
1V differential.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
3
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2V.
Symbol
IGND
Ground Pin Current
VON/OFF
ION/OFF
Parameter
ON/OFF Input Voltage (3)
ON/OFF Input Current
Conditions
Typ
LP2980AI-XX (1)
LP2980I-XX (1)
Min
Min
Max
IL = 0
65
95
125
95
125
IL = 1 mA
80
110
170
110
170
IL = 10 mA
140
220
460
220
460
IL = 50 mA
375
600
1200
600
1200
VON/OFF < 0.18V
0
High = O/P ON
1.4
1
Low = O/P OFF
0.55
0.18
0.18
VON/OFF = 0
0
−1
−1
VON/OFF = 5V
5
15
15
1.6
Units
Max
μA
1
1.6
V
μA
IO(PK)
Peak Output Current
VOUT ≥ VO(NOM) − 5%
150
en
Output Noise Voltage
(RMS)
BW = 300 Hz–50 kHz, COUT
= 10 μF
160
μV
Ripple Rejection
f = 1 kHz
COUT = 10 μF
63
dB
150
mA
IO(MAX)
(3)
(4)
Short Circuit Current
RL = 0 (Steady State)
(4)
100
100
mA
The ON/OFF inputs must be properly driven to prevent misoperation. For details, refer to ON/OFF INPUT OPERATION.
See related curve(s) in TYPICAL PERFORMANCE CHARACTERISTICS section.
Typical Application Circuit
*ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used.
**Minimum Output Capacitance is 1 μF to insure stability over full load current range. More capacitance provides
superior dynamic performance and additional stability margin (see APPLICATION HINTS).
***Do not make connections to this pin.
Figure 3.
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Output Voltage vs Temperature
Output Voltage vs Temperature
Figure 4.
Figure 5.
Dropout Characteristics
Output Voltage vs Temperature
Figure 6.
Figure 7.
Dropout Characteristics
Dropout Characteristics
Figure 8.
Figure 9.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
5
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Dropout Voltage vs Temperature
Dropout Voltage vs Load Current
Figure 10.
Figure 11.
Ground Pin Current vs Temperature
Ground Pin Current vs Load Current
Figure 12.
Figure 13.
Input Current vs VIN
Input Current vs VIN
Figure 14.
6
Figure 15.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Line Transient Response
Line Transient Response
Figure 16.
Figure 17.
Load Transient Response
Load Transient Response
Figure 18.
Figure 19.
Load Transient Response
Load Transient Response
Figure 20.
Figure 21.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
7
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
8
Short Circuit Current
Instantaneous Short Circuit Current
vs Temperature
Figure 22.
Figure 23.
Short Circuit Current
Output Impedance vs
Frequency
Figure 24.
Figure 25.
Output Impedance vs
Frequency
Output Noise Density
Figure 26.
Figure 27.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Ripple Rejection
Input to Output Leakage
vs Temperature
Figure 28.
Figure 29.
Output Reverse Leakage vs
Temperature
Turn-On Waveform
Figure 30.
Figure 31.
Turn-Off Waveform
ON/OFF Pin Current vs VON/OFF
Figure 32.
Figure 33.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
9
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
APPLICATION HINTS
OUTPUT CAPACITOR
Like any low-dropout regulator, the LP2980-N requires an output capacitor to maintain regulator loop stability.
This capacitor must be selected to meet the requirements of minimum capacitance and equivalent series
resistance (ESR) range. It is not difficult to find capacitors which meet the criteria of the LP2980-N, as the
acceptable capacitance and ESR ranges are wider than for most other LDOs.
In general, the capacitor value must be at least 1 μF (over the actual ambient operating temperature), and the
ESR must be within the range indicated in Figure 34, Figure 35 and Figure 36. It should be noted that, although
a maximum ESR is shown in these Figures, it is very unlikely to find a capacitor with ESR that high.
Tantalum Capacitors
Surface-mountable solid tantalum capacitors offer a good combination of small physical size for the capacitance
value, and ESR in the range needed by the LP2980-N.
The results of testing the LP2980-N stability with surface-mount solid tantalum capacitors show good stability
with values of at least 1 μF. The value can be increased to 2.2 μF (or more) for even better performance,
including transient response and noise.
Small value tantalum capacitors that have been verified as suitable for use with the LP2980-N are shown in
Table 1. Capacitance values can be increased without limit.
Aluminum Electrolytic Capacitors
Although probably not a good choice for a production design, because of relatively large physical size, an
aluminum electrolytic capacitor can be used in the design prototype for an LP2980-N regulator. A value of at
least 1 μF should be used, and the ESR must meet the conditions of Figure 34, Figure 35 and Figure 36. If the
operating temperature drops below 0°C, the regulator may not remain stable, as the ESR of the aluminum
electrolytic capacitor will increase, and may exceed the limits indicated in the Figures.
Table 1. Surface-Mount Tantalum Capacitor
Selection Guide
1 μF Surface-Mount Tantalums
Manufacturer
Part Number
Kemet
T491A105M010AS
NEC
NRU105M10
Siemens
B45196-E3105-K
Nichicon
F931C105MA
Sprague
293D105X0016A2T
2.2 μF Surface-Mount Tantalums
Manufacturer
Part Number
Kemet
T491A225M010AS
NEC
NRU225M06
Siemens
B45196/2.2/10/10
Nichicon
F930J225MA
Sprague
293D225X0010A2T
Multilayer Ceramic Capacitors
Surface-mountable multilayer ceramic capacitors may be an attractive choice because of their relatively small
physical size and excellent RF characteristics. However, they sometimes have ESR values lower than the
minimum required by the LP2980-N, and relatively large capacitance change with temperature. The
manufacturer's datasheet for the capacitor should be consulted before selecting a value.
Test results of LP2980-N stability using multilayer ceramic capacitors show that a minimum value of 2.2 μF is
usually needed for the 5V regulator. For the lower output voltages, or for better performance, a higher value
should be used, such as 4.7 μF.
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
Multilayer ceramic capacitors that have been verified as suitable for use with the LP2980-N are shown in
Table 2.
Table 2. Surface-Mount Multilayer Ceramic Capacitor Selection Guide
2.2 μF Surface-Mount Ceramic
Manufacturer
Part Number
Tokin
1E225ZY5U-C203
Murata
GRM42-6Y5V225Z16
4.7 μF Surface-Mount Ceramic
Manufacturer
Part Number
Tokin
1E475ZY5U-C304
Figure 34. 1 μF ESR Range
Figure 35. 2.2 μF ESR Range
Figure 36. 10 μF ESR Range
REVERSE CURRENT PATH
The internal PNP power transistor used as the pass element in the LP2980-N has an inherent diode connected
between the regulator output and input. During normal operation (where the input voltage is higher than the
output) this diode is reverse biased (See Figure 37).
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
11
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
VIN
VOUT
PNP
GND
Figure 37. LP2980 Reverse Current Path
However, if the input voltage is more than a VBE below the output voltage, this diode will turn ON and current will
flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into
the VIN pin and out the ground pin, which can damage the part.
The internal diode can also be turned on if the input voltage is abruptly stepped down to a voltage which is a VBE
below the output voltage.
In any application where the output voltage may be higher than the input voltage, an external Schottky diode
must be connected from VIN to VOUT (cathode on VIN, anode on VOUT. See Figure 38), to limit the reverse voltage
across the LP2980-N to 0.3V (See ABSOLUTE MAXIMUM RATINGS).
SCHOTTKY DIODE
VIN
VOUT
PNP
GND
Figure 38. Adding External Schottky Diode Protection
ON/OFF INPUT OPERATION
The LP2980-N is shut off by pulling the ON/OFF input low, and turned on by driving the input high. If this feature
is not to be used, the ON/OFF input should be tied to VIN to keep the regulator on at all times (the ON/OFF input
must not be left floating).
To ensure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and
below the specified turn-on/turn-off voltage thresholds which ensure an ON or OFF state (see ELECTRICAL
CHARACTERISTICS).
The ON/OFF signal may come from either a totem-pole output, or an open-collector output with pull-up resistor to
the LP2980-N input voltage or another logic supply. The high-level voltage may exceed the LP2980-N input
voltage, but must remain within the Absolute Maximum Ratings for the ON/OFF pin.
It is also important that the turn-on/turn-off voltage signals applied to the ON/OFF input have a slew rate which is
greater than 40 mV/μs.
IMPORTANT: The regulator shutdown function will not operate correctly if a slow-moving signal is used to drive
the ON/OFF input.
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
Increasing Output Current
Figure 39. 5V/400mA Regulator
The LP2980-N can be used to control higher-current regulators, by adding an external PNP pass device. With
the PNP transistors shown in Figure 39, the output current can be as high as 400 mA, as long as the input
voltage is held within the Safe Operation Boundary Curves shown below in Figure 40.
To ensure regulation, the minimum input voltage of this regulator is 6V. This “headroom” is the sum of the VBE of
the external transistor and the dropout voltage of the LP2980-N.
Notes:
1. Drive this input with a logic signal (see APPLICATION HINTS). If the shutdown function is not to be used, tie
the ON/OFF pin directly to the VIN pin.
2. Recommended devices (other PNP transistors can be used if the current gain and voltage ratings are
similar).
3. Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit.
4. Increasing the output capacitance improves transient response and increases phase margin.
5. Maximum safe input voltage and load current are limited by power dissipation in the PNP pass transistor and
the maximum ambient temperature for the specific application. If a TO-92 transistor such as the MPS2907A
is used, the thermal resistance from junction-to-ambient is 180°C/W in still air.
Assuming a maximum allowable junction temperature of 150°C for the MPS2907A device, the following curves
show the maximum VIN and IL values that may be safely used for several ambient temperatures.
Figure 40. Safe Operation Boundary Curves for Figure 39
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
13
LP2980-N
SNOS733M – APRIL 2000 – REVISED JUNE 2013
www.ti.com
Figure 41. 5V to 3.3V @ 3A Converter
With limited input voltage range, the LP2980-N can control a 3.3V, 3A regulator with the use of a high currentgain external PNP pass transistor as shown in Figure 41. If the regulator is to be loaded with the full 3A, heat
sinking will be required on the pass transistor to keep it within its rated temperature range. Refer to Figure 42 .
For best load regulation at the high load current, the LP2980-N output voltage connection should be made as
close to the load as possible.
Although this regulator can handle a much higher load current than can the LP2980-N alone, it can be shut down
in the same manner as the LP2980-N. When the ON/OFF control is brought low, the converter will be in
shutdown, and will draw less than 1 μA from the source.
Notes:
1. Drive this input with a logic signal (see APPLICATION HINTS). If the shutdown function is not to be used, tie
the ON/OFF pin directly to the VIN pin.
2. Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit.
3. Increasing the output capacitance improves transient response and increases phase margin.
4. A heatsink may be required for this transistor. The maximum allowable value for thermal resistance of the
heatsink is dependent on ambient temperature and load current (see curves in Figure 42). Once the value is
obtained from the graph, a heatsink must be selected which has a thermal resistance equal to or lower than
this value. If the value is above 60°C/W, no heatsink is required (the TO-220 package alone will safely
dissipate this).
For these curves, a maximum junction temperature of 150°C is assumed for the pass transistor. The case-toheatsink attachment thermal resistance is assumed to be 1.5°C/W. All calculations are for 5.5V input voltage
(which is worst-case for power dissipation).
Figure 42. Heatsink Thermal Resistance Requirements for Figure 41
14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
LP2980-N
www.ti.com
SNOS733M – APRIL 2000 – REVISED JUNE 2013
REVISION HISTORY
Changes from Revision L (April 2013) to Revision M
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LP2980-N
15
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP2980AIM5-2.5
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L0NA
LP2980AIM5-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0NA
LP2980AIM5-3.0
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L02A
LP2980AIM5-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L02A
LP2980AIM5-3.3
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L00A
LP2980AIM5-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L00A
LP2980AIM5-4.7/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L37A
LP2980AIM5-5.0
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L01A
LP2980AIM5-5.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L01A
LP2980AIM5X-2.5
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L0NA
LP2980AIM5X-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0NA
LP2980AIM5X-3.0
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L02A
LP2980AIM5X-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L02A
LP2980AIM5X-3.3
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L00A
LP2980AIM5X-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L00A
LP2980AIM5X-4.7
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L37A
LP2980AIM5X-4.7/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L37A
LP2980AIM5X-5.0
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L01A
LP2980AIM5X-5.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L01A
LP2980IM5-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0NB
LP2980IM5-3.0
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L02B
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Nov-2013
Status
(1)
LP2980IM5-3.0/NOPB
Package Type Package Pins Package
Drawing
Qty
ACTIVE
SOT-23
DBV
5
1000
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L02B
(4/5)
LP2980IM5-3.3
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L00B
LP2980IM5-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L00B
LP2980IM5-3.8/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L21B
LP2980IM5-4.7/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L37B
LP2980IM5-5.0
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L01B
LP2980IM5-5.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L01B
LP2980IM5X-2.5
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L0NB
LP2980IM5X-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0NB
LP2980IM5X-3.0
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L02B
LP2980IM5X-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L02B
LP2980IM5X-3.3
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L00B
LP2980IM5X-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L00B
LP2980IM5X-4.7/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L37B
LP2980IM5X-5.0
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L01B
LP2980IM5X-5.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L01B
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
B0
(mm)
K0
(mm)
P1
(mm)
LP2980AIM5-2.5
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5-2.5/NOPB
SOT-23
DBV
5
1000
178.0
LP2980AIM5-3.0
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
LP2980AIM5-3.0/NOPB
SOT-23
DBV
5
1000
Q3
178.0
8.4
3.2
3.2
1.4
4.0
8.0
LP2980AIM5-3.3
SOT-23
DBV
5
Q3
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5-3.3/NOPB
SOT-23
DBV
LP2980AIM5-4.7/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
LP2980AIM5-5.0
SOT-23
Q3
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5-5.0/NOPB
LP2980AIM5X-2.5
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5X-2.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5X-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5X-3.3/NOPB SOT-23
LP2980AIM5X-3.0
LP2980AIM5X-3.3
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
W
Pin1
(mm) Quadrant
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5X-4.7/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980AIM5X-4.7
LP2980AIM5X-5.0
SOT-23
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Package Pins
Type Drawing
LP2980AIM5X-5.0/NOPB SOT-23
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-2.5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-3.0
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-3.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-3.3
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-3.8/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-4.7/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-5.0
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5-5.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-2.5
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-2.5/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-3.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-3.0/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-3.3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-4.7/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-5.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2980IM5X-5.0/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
*All dimensions are nominal
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP2980AIM5-2.5
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-3.0
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-3.3
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-4.7/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-5.0
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5-5.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980AIM5X-2.5
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-3.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-3.3
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-4.7
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-4.7/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-5.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980AIM5X-5.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-3.0
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-3.3
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-3.8/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-4.7/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-5.0
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5-5.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2980IM5X-2.5
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-3.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-3.3
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-4.7/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-5.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2980IM5X-5.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated