High Precision 5 V Reference AD586 Laser trimmed to high accuracy 5.000 V ±2.0 mV (M grade) Trimmed temperature coefficient 2 ppm/°C max, 0°C to 70°C (M grade) 5 ppm/°C max, −40°C to +85°C (B and L grades) 10 ppm/°C max, −55°C to +125°C (T grade) Low noise, 100 nV/√Hz Noise reduction capability Output trim capability MIL-STD-883-compliant versions available Industrial temperature range SOICs available Output capable of sourcing or sinking 10 mA The AD586J, AD586K, AD586L, and AD586M are available in an 8-lead PDIP; the AD586J, AD586K, AD586L, AD586A, and AD586B are available in an 8-lead SOIC package; and the AD586J, AD586K, AD586L, AD586S, and AD586T are available in an 8-lead CERDIP package. VIN NOISE REDUCTION 2 8 AD586 RZ1 RS A1 6 VOUT 5 TRIM NOTES 1. PINS 1, 3, AND 7 ARE INTERNAL TEST POINTS. MAKE NO CONNECTIONS TO THESE POINTS. 00529-001 FEATURES RZ2 RF RT RI GENERAL DESCRIPTION 4 The AD586 represents a major advance in state-of-the-art monolithic voltage references. Using a proprietary ion-implanted buried Zener diode and laser wafer trimming of high stability thin-film resistors, the AD586 provides outstanding performance at low cost. The AD586 offers much higher performance than most other 5 V references. Because the AD586 uses an industry-standard pinout, many systems can be upgraded instantly with the AD586. The buried Zener approach to reference design provides lower noise and drift than band gap voltage references. The AD586 offers a noise reduction pin that can be used to further reduce the noise level generated by the buried Zener. The AD586 is recommended for use as a reference for 8-, 10-, 12-, 14-, or 16-bit DACs that require an external precision reference. The device is also ideal for successive approximation or integrating ADCs with up to 14 bits of accuracy and, in general, can offer better performance than the standard on-chip references. The AD586J, AD586K, AD586L, and AD586M are specified for operation from 0°C to 70°C; the AD586A and AD586B are specified for −40°C to +85°C operation; and the AD586S and AD586T are specified for −55°C to +125°C operation. GND Figure 1. PRODUCT HIGHLIGHTS 1. Laser trimming of both initial accuracy and temperature coefficients results in very low errors over temperature without the use of external components. The AD586M has a maximum deviation from 5.000 V of ±2.45 mV between 0°C and 70°C, and the AD586T guarantees ±7.5 mV maximum total error between −55°C and +125°C. 2. For applications requiring higher precision, an optional fine-trim connection is provided. 3. Any system using an industry-standard pinout reference can be upgraded instantly with the AD586. 4. Output noise of the AD586 is very low, typically 4 µV p-p. A noise reduction pin is provided for additional noise filtering using an external capacitor. 5. The AD586 is available in versions compliant with MIL-STD-883. Refer to the Analog Devices Military Products Databook or the current AD586/883B data sheet for detailed specifications. Rev. G Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 © 2005 Analog Devices, Inc. All rights reserved. AD586 TABLE OF CONTENTS Specifications..................................................................................... 3 Load Regulation ............................................................................9 AD586J, AD586K/AD586A, AD586L/AD586B ....................... 3 Temperature Performance............................................................9 AD586M, AD586S, AD586T....................................................... 4 Negative Reference Voltage from an AD586........................... 10 Absolute Maximum Ratings............................................................ 5 Using the AD586 with Converters ........................................... 10 ESD Caution.................................................................................. 5 5 V Reference with Multiplying CMOS DACs or ADCs ...... 11 Pin Configurations and Function Descriptions ........................... 6 Stacked Precision References for Multiple Voltages .............. 11 Theory of Operation ........................................................................ 7 Precision Current Source .......................................................... 11 Applying the AD586..................................................................... 7 Precision High Current Supply ................................................ 11 Noise Performance and Reduction ............................................ 7 Outline Dimensions ....................................................................... 13 Turn-on Time................................................................................ 8 Ordering Guide .......................................................................... 14 Dynamic Performance................................................................. 8 REVISION HISTORY 3/05—Rev. F to Rev. G Updated Format..................................................................Universal Split Specifications Table into Table 1 and Table 2....................... 3 Changes to Table 1............................................................................ 3 Added Figure 2 and Figure 4........................................................... 6 Updated Outline Dimensions ....................................................... 13 Changes to Ordering Guide .......................................................... 14 1/04—Rev. E to Rev. F Changes to ORDERING GUIDE ................................................... 3 7/03—Rev. D to Rev. E Removed AD586J CHIPS ..................................................Universal Updated ORDERING GUIDE........................................................ 3 Change to Figure 3 ........................................................................... 4 Updated Figure 12 ............................................................................ 7 Updated OUTLINE DIMENSIONS .............................................. 9 4/01—Rev. C to Rev. D Changed Figure 10 to Table 1 (Maximum Output Change in mV)............................................... 6 11/95—Revision 0: Initial Version Rev. G | Page 2 of 16 AD586 SPECIFICATIONS AD586J, AD586K/AD586A, AD586L/AD586B @ TA = 25°C, VIN = 15 V, unless otherwise noted. Specifications in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed, although only those shown in boldface are tested on all production units, unless otherwise specified. Table 1. Parameter Min OUTPUT VOLTAGE OUTPUT VOLTAGE DRIFT1 0°C to 70°C −55°C to +125°C GAIN ADJUSTMENT 4.980 LINE REGULATION1 10.8 V < + VIN < 36 V TMIN to TMAX 11.4 V < +VIN < 36 V TMIN to TMAX LOAD REGULATION1 Sourcing 0 mA < IOUT < 10 mA 25°C TMIN to TMAX Sinking −10 mA < IOUT < 0 mA 25°C QUIESCENT CURRENT POWER CONSUMPTION OUTPUT NOISE 0.1 Hz to 10 Hz Spectral Density, 100 Hz LONG-TERM STABILITY SHORT-CIRCUIT CURRENT-TO-GROUND TEMPERATURE RANGE Specified Performance2 Operating Performance3 1 2 3 AD586J Typ Max AD586K/AD586A Min Typ Max Min 5.020 4.995 4.9975 5.005 25 +6 −2 AD586L/AD586B Typ Max 15 +6 −2 V 5 ppm/°C ppm/°C % % ±100 µV/V +6 −2 ±100 ±100 Unit 5.0025 µV/V 100 100 2 30 100 100 400 3 2 30 4 100 15 45 400 3 2 30 4 100 15 60 0 70 −40 +85 0 −40 −40 100 100 µV/mA µV/mA 400 3 µV/mA mA mW 4 100 15 45 60 (K grade) (A grade) 70 +85 +85 0 −40 −40 µV p-p nV/√Hz ppm/1000 hr 45 60 mA (L grade) (B grade) 70 +85 °C °C +85 °C Maximum output voltage drift is guaranteed for all packages and grades. CERDIP packaged parts are also 100°C production tested. Lower row shows specified performance for A and B grades. The operating temperature range is defined as the temperature extremes at which the device will still function. Parts may deviate from their specified performance outside their specified temperature range. Rev. G | Page 3 of 16 AD586 AD586M, AD586S, AD586T @ TA = 25°C, VIN = 15 V, unless otherwise noted. Specifications in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed, although only those shown in boldface are tested on all production units, unless otherwise specified. Table 2. Parameter Min OUTPUT VOLTAGE OUTPUT VOLTAGE DRIFT1 0°C to 70°C −55°C to +125°C GAIN ADJUSTMENT 4.998 LINE REGULATION1 10.8 V < +VIN < 36 V TMIN to TMAX 11.4 V < +VIN < 36 V TMIN to TMAX LOAD REGULATION1 Sourcing 0 mA < IOUT < 10 mA 25°C TMIN to TMAX Sinking −10 mA < IOUT < 0 mA 25°C QUIESCENT CURRENT POWER CONSUMPTION OUTPUT NOISE 0.1 Hz to 10 Hz Spectral Density, 100 Hz LONG-TERM STABILITY SHORT-CIRCUIT CURRENT-TO-GROUND TEMPERATURE RANGE Specified Performance2 Operating Performance3 1 2 3 AD586M Typ Max 5.002 Min AD586S Typ 4.990 Max Min 5.010 4.9975 AD586T Typ Max 5.0025 2 20 +6 −2 +6 −2 10 +6 −2 100 100 400 3 2 30 ±150 ±150 µV/V 150 150 150 150 µV/mA µV/mA 400 3 µV/mA mA mW 400 3 2 30 4 100 4 100 4 100 µV p-p nV/√Hz 15 15 15 ppm/1000 hr 45 0 −40 ppm/°C ppm/°C % % µV/V ±100 2 30 Unit V 60 70 +85 45 −55 −55 60 +125 +125 45 −55 −55 60 mA +125 +125 °C °C Maximum output voltage drift is guaranteed for all packages and grades. CERDIP packaged parts are also 100°C production tested. Lower row shows specified performance for A and B grades. The operating temperature range is defined as the temperature extremes at which the device will still function. Parts may deviate from their specified performance outside their specified temperature range. Rev. G | Page 4 of 16 AD586 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VIN to Ground Power Dissipation (25°C) Storage Temperature Lead Temperature (Soldering, 10 sec) Package Thermal Resistance θJC θJA Output Protection Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rating 36 V 500 mW −65°C to +150°C 300°C 22°C/W 110°C/W Output safe for indefinite short to ground or VIN. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. G | Page 5 of 16 AD586 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS TP1 1 AD586 Figure 2. Pin Configuration (N-8) GND 4 00529-002 DENOTES FACTORY TEST POINT. NO CONNECTIONS, EXCEPT DUMMY PCB PAD, SHOULD BE MADE TO THESE POINTS. TP1 1 VIN 2 VIN 2 TOP VIEW TP1 3 (Not to Scale) 6 VOUT TOP VIEW 6 VOUT (Not to Scale) GND 4 5 TRIM TP1 3 1 TP NOISE REDUCTION 7 TP1 8 AD586 5 NO CONNECTIONS, EXCEPT DUMMY PCB PAD, SHOULD BE MADE TO THESE POINTS. Figure 3. Pin Configuration (Q-8) Mnemonic TP1 VIN TP1 GND TRIM VOUT TP1 NOICE REDUCTION TP1 1 TP DENOTES FACTORY TEST POINT. NO CONNECTIONS, EXCEPT DUMMY PCB PAD, SHOULD BE MADE TO THESE POINTS. Figure 4. Pin Configuration (R-8) Description Factory Trim Pad (No Connect). Input Voltage. Factory Trim Pad (No Connect). Ground. Optional External Fine Trim. See the Applying the AD586 section. Output Voltage. Factory Trim Pad (No Connect). Optional Noise Reduction Filter with External 1µF Capacitor to Ground. Rev. G | Page 6 of 16 7 6 VOUT TOP VIEW GND 4 (Not to Scale) 5 TRIM Table 4. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 NOISE REDUCTION TP1 3 TRIM 1 TP DENOTES FACTORY TEST POINT. AD586 8 00529-004 VIN 2 NOISE REDUCTION 7 TP1 8 00529-003 TP1 1 AD586 THEORY OF OPERATION Using the bias compensation resistor between the Zener output and the noninverting input to the amplifier, a capacitor can be added at the noise reduction pin (Pin 8) to form a low-pass filter and reduce the noise contribution of the Zener to the circuit. NOISE REDUCTION 2 8 AD586 RZ1 RS A1 RZ2 RF 6 VOUT 5 TRIM RT RI AD586 8 OPTIONAL NOISE REDUCTION CAPACITOR NOISE REDUCTION CN 1µF OUTPUT VO 6 10kΩ TRIM 5 GND 4 Figure 6. Optional Fine-Trim Configuration NOISE PERFORMANCE AND REDUCTION The noise generated by the AD586 is typically less than 4 µV p-p over the 0.1 Hz to 10 Hz band. Noise in a 1 MHz bandwidth is approximately 200 µV p-p. The dominant source of this noise is the buried Zener, which contributes approximately 100 nV/√Hz. By comparison, contribution by the op amp is negligible. Figure 7 shows the 0.1 Hz to 10 Hz noise of a typical AD586. The noise measurement is made with a band-pass filter made of a 1-pole high-pass filter with a corner frequency at 0.1 Hz, and a 2-pole low-pass filter with a corner frequency at 12.6 Hz, to create a filter with a 9.922 Hz bandwidth. If further noise reduction is desired, an external capacitor can be added between the noise reduction pin and ground, as shown in Figure 6. This capacitor, combined with the 4 kΩ RS and the Zener resistances, forms a low-pass filter on the output of the Zener cell. A 1 µF capacitor will have a 3 dB point at 12 Hz, and will reduce the high frequency (to 1 MHz) noise to about 160 µV p-p. Figure 8 shows the 1 MHz noise of a typical AD586, both with and without a 1 µF capacitor. 4 00529-001 GND NOTES 1. PINS 1, 3, AND 7 ARE INTERNAL TEST POINTS. MAKE NO CONNECTIONS TO THESE POINTS. 2 VIN Figure 5. Functional Block Diagram APPLYING THE AD586 The AD586 is simple to use in virtually all precision reference applications. When power is applied to Pin 2 and Pin 4 is grounded, Pin 6 provides a 5 V output. No external components are required; the degree of desired absolute accuracy is achieved simply by selecting the required device grade. The AD586 requires less than 3 mA quiescent current from an operating supply of 12 V or 15 V. An external fine trim may be desired to set the output level to exactly 5.000 V (calibrated to a main system reference). System calibration may also require a reference voltage that is slightly different from 5.000 V, for example, 5.12 V for binary applications. In either case, the optional trim circuit shown in Figure 6 can offset the output by as much as 300 mV with minimal effect on other device characteristics. Rev. G | Page 7 of 16 1µF 5s 1µF 00529-006 VIN VIN 00529-005 The AD586 consists of a proprietary buried Zener diode reference, an amplifier to buffer the output, and several high stability thin-film resistors, as shown in the block diagram in Figure 5. This design results in a high precision monolithic 5 V output reference with initial offset of 2.0 mV or less. The temperature compensation circuitry provides the device with a temperature coefficient of under 2 ppm/°C. Figure 7. 0.1 Hz to 10 Hz Noise AD586 200µV 10V 50µS 1mS 5V VIN CN = 1µF VOUT 00529-009 00529-007 NO CN Figure 8. Effect of 1 µF Noise Reduction Capacitor on Broadband Noise Figure 10. Extended Time Scale TURN-ON TIME 10V Output turn-on time is modified when an external noise reduction capacitor is used. When present, this capacitor acts as an additional load to the current source of the internal Zener diode, resulting in a somewhat longer turn-on time. In the case of a 1 µF capacitor, the initial turn-on time is approximately 400 ms to 0.01% (see Figure 11). 1mV 100mS VOUT Figure 11. Turn-On with 1µF CN Characteristics DYNAMIC PERFORMANCE The output buffer amplifier is designed to provide the AD586 with static and dynamic load regulation superior to less complete references. Many ADCs and DACs present transient current loads to the reference, and poor reference response can degrade the performance of the converter. VOUT Figure 12, Figure 13, and Figure 14 display the characteristics of the AD586 output amplifier driving a 0 mA to 10 mA load. VOUT 00529-008 20µS 3.5V 500Ω AD586 Figure 9. Electrical Turn-On VL 5V 0V Figure 12. Transient Load Test Circuit Rev. G | Page 8 of 16 00529-011 10V VIN 1mV VIN 00529-010 Upon application of power (cold start), the time required for the output voltage to reach its final value within a specified error band is defined as the turn-on settling time. Two components normally associated with this are the time for the active circuits to settle, and the time for the thermal gradients on the chip to stabilize. Figure 9, Figure 10, and Figure 11 show the turn-on characteristics of the AD586. It shows the settling to be about 60 µs to 0.01%. Note the absence of any thermal tails when the horizontal scale is expanded to l ms/cm in Figure 10. AD586 5V 5V 1µS 50mV VL 1µS 200mV CL = 0 VOUT 00529-012 00529-015 CL = 1000pF Figure 16. Output Response with Capacitive Load Figure 13. Large-Scale Transient Response 5V LOAD REGULATION 2µS 1mV The AD586 has excellent load regulation characteristics. Figure 17 shows that varying the load several mA changes the output by a few µV. The AD586 has somewhat better load regulation performance sourcing current than sinking current. VL ∆VOUT (µV) VOUT 1000 00529-013 500 2 –6 –4 –2 4 6 8 10 LOAD (mA) 0 –500 Figure 14. Fine-Scale Setting for Transient Load –1000 Figure 17. Typical Load Regulation Characteristics Figure 15 and Figure 16 display the output amplifier characteristics driving a 1000 pF, 0 mA to 10 mA load. AD586 VL TEMPERATURE PERFORMANCE VOUT 500Ω 5V 0V Figure 15. Capacitive Load Transient Response Test Circuit 00529-014 CL 1000pF 3.5V 00529-016 In some applications, a varying load may be both resistive and capacitive in nature, or the load may be connected to the AD586 by a long capacitive cable. The AD586 is designed for precision reference applications where temperature performance is critical. Extensive temperature testing ensures that the device maintains a high level of performance over the operating temperature range. Some confusion exists with defining and specifying reference voltage error over temperature. Historically, references have been characterized using a maximum deviation per degree Celsius, that is, ppm/°C. However, because of nonlinearities in temperature characteristics that originated in standard Zener references (such as “S” type characteristics), most manufacturers have begun to use a maximum limit error band approach to specify devices. This technique involves measuring the output at three or more different temperatures to specify an output voltage error band. Rev. G | Page 9 of 16 AD586 Figure 18 shows the typical output voltage drift for the AD586L and illustrates the test methodology. The box in Figure 18 is bounded on the sides by the operating temperature extremes and on the top and the bottom by the maximum and minimum output voltages measured over the operating temperature range. The slope of the diagonal drawn from the lower left to the upper right corner of the box determines the performance grade of the device. SLOPE = T.C. = VMAX –VMIN (TMAX –TMIN) × 5 × 10–6 5.0027 – 5.0012 (70°C – 0) × 5 × 10–6 = 4.3ppm/°C = SLOPE 0°C to 70°C 8.75 5.25 1.75 0.70 −40°C to +85°C −55°C to +125°C 9.37 3.12 18.00 9.00 NEGATIVE REFERENCE VOLTAGE FROM AN AD586 VMAX VMIN 20 40 60 TEMPERATURE (°C) 80 00625-017 5.000 Figure 18. Typical AD586L Temperature Drift The AD586 can be used to provide a precision −5.000 V output, as shown in Figure 19. The VIN pin is tied to at least a 6 V supply, the output pin is grounded, and the AD586 ground pin is connected through a resistor, RS, to a −15 V supply. The −5 V output is now taken from the ground pin (Pin 4) instead of VOUT. It is essential to arrange the output load and the supply resistor, RS, so that the net current through the AD586 is between 2.5 mA and 10.0 mA. The temperature characteristics and long-term stability of the device will be essentially the same as that of a unit used in the standard +5 V output configuration. +6V → +30V Each AD586J, AD586K, and AD586L grade unit is tested at 0°C, 25°C, and 70°C. Each AD586SQ and AD586TQ grade unit is tested at −55°C, +25°C, and +125°C. This approach ensures that the variations of output voltage that occur as the temperature changes within the specified range will be contained within a box whose diagonal has a slope equal to the maximum specified drift. The position of the box on the vertical scale will change from device to device as initial error and the shape of the curve vary. The maximum height of the box for the appropriate temperature range and device grade is shown in Table 5. Duplication of these results requires a combination of high accuracy and stable temperature control in a test system. Evaluation of the AD586 will produce a curve similar to that in Figure 18, but output readings could vary depending on the test methods and equipment used. 2.5mA < 2 10V –I < 10mA RS L VIN AD586 VOUT 6 GND IL 4 –5V RS –15V 00529-018 5.003 0 Maximum Output Change (mV) Device Grade AD586J AD586K AD586L AD586M AD586A AD586B AD586S AD586T TMAX TMIN –20 Table 5. Maximum Output Change in mV Figure 19. AD586 as a Negative 5 V Reference USING THE AD586 WITH CONVERTERS The AD586 is an ideal reference for a wide variety of 8-, 12-, 14-, and 16-bit ADCs and DACs. Several representative examples are explained in the following sections. Rev. G | Page 10 of 16 AD586 22V TO 46V 5 V REFERENCE WITH MULTIPLYING CMOS DACs OR ADCs 2 VIN The AD586 is ideal for applications with 10- and 12-bit multiplying CMOS DACs. In the standard hookup, as shown in Figure 20, the AD586 is paired with the AD7545 12-bit multiplying DAC and the AD711 high speed BiFET op amp. The amplifier DAC configuration produces a unipolar 0 V to −5 V output range. Bipolar output applications and other operating details can be found in the individual product data sheets. VIN 18 20 AD586 VDD RFB TRIM 5 10kΩ TRIM 5 GND 4 2 VIN C1 33pF AD586 OUT 1 1 VREF 2 7 AD711K AGND AD7545K 3 2 4 TRIM 5 5V 10kΩ GND VOUT 0 V TO –5V DB11 TO DB0 00529-019 3 4 4 VOUT 6 4 0.1µF DGND GND 6 10kΩ TRIM 5 GND VIN +15V 0.1µF 10V VOUT 6 AD586 2 2 19 10kΩ R2 68Ω +15V VOUT 6 15V VOUT 6 00529-021 +15V AD586 –15V Figure 22. Multiple AD586s Stacked for Precision 5 V, 10 V, and 15 V Outputs PRECISION CURRENT SOURCE Figure 20. Low Power 12-Bit CMOS DAC Application The AD586 can also be used as a precision reference for multiple DACs. Figure 21 shows the AD586, the AD7628 dual DAC, and the AD712 dual op amp hooked up for single-supply operation to produce 0 V to −5 V outputs. Because both DACs are on the same die and share a common reference and output op amps, the DAC outputs will exhibit similar gain TCs. The design of the AD586 allows it to be easily configured as a current source. By choosing the control resistor RC in Figure 23, the user can vary the load current from the quiescent current (typically, 2 mA) to approximately 10 mA. The compliance voltage of this circuit varies from about 5 V to 21 V, depending on the value of VIN. +VIN +15V +15V 2 17 VREFA RFB A OUT A 4 4 AD586 2 DAC A AD586 GND VIN DATA INPUTS 14 7 DB0 AGND AD7628 DB7 OUT B 4 VREFB RFB B 1 VOUT A = 0 TO –5V GND VOUT 6 RC (500Ω MIN) IL = 4 AD712 19 5V +I RC BIAS 00529-022 VOUT 6 2 3 Figure 23. Precision Current Source 20 DAC B DGND 5 VOUT B = 0 TO –5V 00529-020 VIN Figure 21. AD586 as a 5 V Reference for a CMOS STACKED PRECISION REFERENCES FOR MULTIPLE VOLTAGES Often, a design requires several reference voltages. Three AD586s can be stacked, as shown in Figure 22, to produce 5.000 V, 10.000 V, and 15.000 V outputs. This scheme can be extended to any number of AD586s, provided the maximum load current is not exceeded. This design provides the additional advantage of improved line regulation on the 5.0 V output. Changes in VIN of 18 V to 50 V produce output changes that are below the noise level of the references. PRECISION HIGH CURRENT SUPPLY For higher currents, the AD586 can easily be connected to a power PNP or power Darlington PNP device. The circuit in Figure 24 and Figure 25 can deliver up to 4 amps to the load. The 0.1 µF capacitor is required only if the load has a significant capacitive component. If the load is purely resistive, improved high frequency supply rejection results can be obtained by removing the capacitor. Rev. G | Page 11 of 16 AD586 15V 15V 220Ω 220Ω 2N6285 2N6285 0.1µF 0.1µF 2 GND RC 4 VOUT 6 AD586 GND 00529-023 VOUT 6 AD586 VIN 5V IL = +I RC BIAS VOUT 5V @ 4 AMPS 4 Figure 24. Precision High Current Current Source Figure 25. Precision High Current Voltage Source Rev. G | Page 12 of 16 00529-024 2 VIN AD586 OUTLINE DIMENSIONS 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 8 5 1 4 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) PIN 1 0.100 (2.54) BSC 5.00 (0.1968) 4.80 (0.1890) 0.060 (1.52) MAX 0.210 (5.33) MAX 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) MIN 0.015 (0.38) GAUGE PLANE SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COMPLIANT TO JEDEC STANDARDS MS-001-BA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 5 4 0.100 (2.54) BSC 0.320 (8.13) 0.290 (7.37) 0.060 (1.52) 0.015 (0.38) 0.150 (3.81) MIN SEATING 0.070 (1.78) PLANE 0.030 (0.76) 15° 0° 0.50 (0.0196) × 45° 0.25 (0.0099) 8° 0.25 (0.0098) 0° 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) Figure 28. 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 0.055 (1.40) MAX 0.405 (10.29) MAX 1.75 (0.0688) 1.35 (0.0532) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 0.310 (7.87) 0.220 (5.59) PIN 1 6.20 (0.2440) 5.80 (0.2284) 0.51 (0.0201) COPLANARITY 0.31 (0.0122) SEATING 0.10 PLANE Figure 26. 8-Lead Plastic Dual In-Line Package [PDIP] (N-8) Dimensions shown in inches and (millimeters) 1 4 0.430 (10.92) MAX 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 8 5 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.005 (0.13) MIN 0.005 (0.13) MIN 8 4.00 (0.1574) 3.80 (0.1497) 1 0.015 (0.38) 0.008 (0.20) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 27. 8-Lead Ceramic Dual In-Line Package [CERDIP] (Q-8) Dimensions shown in inches and (millimeters) Rev. G | Page 13 of 16 AD586 ORDERING GUIDE Model AD586JN AD586JNZ1 AD586JQ AD586JR AD586JR-REEL7 AD586JRZ1 AD586JRZ-REEL71 AD586KN AD586KNZ1 AD586KQ AD586KR AD586KR-REEL AD586KR-REEL7 AD586KRZ1 AD586KRZ-REEL1 AD586KRZ-REEL71 AD586LN AD586LNZ1 AD586LR AD586LR-REEL AD586LR-REEL7 AD586LRZ1 AD586LRZ-REEL1 AD586LRZ-REEL71 AD586MN AD586MNZ1 AD586AR AD586AR-REEL AD586ARZ1 AD586ARZ-REEL1 AD586ARZ-REEL71 AD586BR AD586BR-REEL7 AD586BRZ1 AD586BRZ-REEL1 AD586BRZ-REEL71 AD586LQ AD586SQ AD586TQ AD586TQ/883B2 1 2 Initial Error 20 mV 20 mV 20 mV 20 mV 20 mV 20 mV 20 mV 5 mV 5 mV 5 mV 5 mV 5 mV 5 mV 5 mV 5 mV 5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2 mV 2 mV 5 mV 5 mV 5 mV 5 mV 5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 2.5 mV 10 mV 2.5 mV 2.5 mV Temperature Coefficient 25 ppm/°C 25 ppm/°C 25 ppm/°C 25 ppm/°C 25 ppm/°C 25 ppm/°C 25 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 2 ppm/°C 2 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 15 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 20 ppm/°C 10 ppm/°C 10 ppm/°C Temperature Range 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C 0°C to 70°C −55°C to +125°C −55°C to +125°C −55°C to +125°C Package Description PDIP PDIP CERDIP SOIC SOIC SOIC SOIC PDIP PDIP CERDIP SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC CERDIP CERDIP CERDIP CERDIP Package Option N-8 N-8 Q-8 R-8 R-8 R-8 R-8 N-8 N-8 Q-8 R-8 R-8 R-8 R-8 R-8 R-8 N-8 N-8 R-8 R-8 R-8 R-8 R-8 R-8 N-8 N-8 R-8 R-8 R-8 R-8 R-8 R-8 R-8 R-8 R-8 R-8 Q-8 Q-8 Q-8 Q-8 Quantity Per Reel 1,000 1,000 2,500 1,000 2,500 1,000 2,500 1,000 2,500 1,000 2,500 2,500 1,000 1,000 2,500 1,000 Z = Pb-free part. For details on grade and package offerings screened in accordance with MIL-STD-883, refer to the Analog Devices Military Products Databook or the current AD586/883B data sheet. Rev. G | Page 14 of 16 AD586 NOTES Rev. G | Page 15 of 16 AD586 NOTES © 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00529–0–3/05(G) Rev. G | Page 16 of 16