LCD10W LCD10W SERIES DC-DC CONVERTER 4:1 ULTRA WIDE INPUT RANGE UP TO 10Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • 1600VDC INPUT TO OUTPUT ISOLATION • SMALL SIZE AND LOW PROFILE 1.0 x 1.0 x 0.39 INCH • SIX-SIDED CONTINUOUS SHIELD • BUILT-IN EN55022 CLASS B FILTER • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT ： 1600VDC ISOLATION REMOTE CONTROL UVP OCP SCP LOW STANDBY POWER OVP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted Model Number Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 3000 2000 830 670 416 ±1000 ±416 ±333 3000 2000 830 670 416 ±1000 ±416 ±333 mA 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 85 87 90 91 90 87 89 89 85 87 90 90 90 87 89 89 µF 3500 2500 430 350 125 ±1440 ±250 ±180 3500 2500 430 350 125 ±1440 ±250 ±180 LCD10-24S3P3W LCD10-24S05W LCD10-24S12W LCD10-24S15W LCD10-24S24W LCD10-24D05W LCD10-24D12W LCD10-24D15W LCD10-48S3P3W LCD10-48S05W LCD10-48S12W LCD10-48S15W LCD10-48S24W LCD10-48D05W LCD10-48D12W LCD10-48D15W PART NUMBER STRUCTURE LCD10 - 48 Series Name Input Voltage (VDC) 24: 9~36 48: 18~75 S Output Quantity S: Single D: Dual 1 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 24: 24 05: ±5 12: ±12 15: ±15 W Input Range 4:1 : A: B: C: D: E: A HS Option Assembly Option Negative logic remote ON/OFF(Standard) Positive logic remote ON/OFF Without Ctrl pin Negative logic remote ON/OFF without Trim pin Without Ctrl & Trim pin Positive logic remote ON/OFF without Trim pin www.PDUKE.com : No Assembly Option HS: Heat-sink HC: Heat-sink & Clamp 2014/04/30 LCD10W INPUT SPECIFICATIONS Parameter Conditions 24Vin(nom) 48Vin(nom) Operating input voltage range Input reflected ripple current Start-up voltage Start up time Constant resistive load Input surge voltage 1 second, max. Remote ON/OFF Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 24Vin(nom) 48Vin(nom) Positive logic DC-DC ON (Option) DC-DC OFF Negative logic DC-DC ON (Standard) DC-DC OFF Input current of Ctrl pin Remote off input current Conditions Output power Low Line to High Line at Full Load Load regulation No Load to Full Load Cross regulation Voltage adjustability (2) Asymmetrical load 25%/100% FL Single output Ripple and noise Measured by 20MHz bandwidth With a 10µF/25V X7R 1206 MLCC VDC -0.5 Typ. 11 12 +1.0 +0.2 +0.5 +0.2 +1.0 +0.1 +0.8 +5.0 +10 +20 60 500VDC +0.02 3.7 6.3 13.5 18.3 29.1 ms VDC mA mA Unit W % % % % % mVp-p 250 % of Iout rated; Hiccup mode Isolation resistance Isolation capacitance Switching frequency Safety approvals Max. 40 60 24Vout 3.3Vout 5Vout 12Vout 15Vout 24Vout 1 minute VDC 30 30 50 100 Open or 3 ~ 15VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 15VDC 1.0 2.5 -1.0 -0.2 -0.5 -0.2 -1.0 -0.1 -0.8 -5.0 -10 -10 25% load step change Isolation voltage VDC 8 16 -0.02 GENERAL SPECIFICATIONS Parameter mAp-p 9 18 3.3Vout, 5Vout 12Vout, 15Vout With a 1µF/50V X7R 1206 MLCC 2 Unit 36 75 Min. Single Dual Single Dual Single Dual Dual 3.3Vout, 12Vout Others 10% Load to 90%Load Case material Base material Potting material Weight MTBF Max. 24 48 30 Output voltage trimmed up 10% Output voltage trimmed up 20% Voltage accuracy Line regulation Over load protection Short circuit protection Typ. 9 18 Nominal input and Full load Shutdown voltage Temperature coefficient Transient response recovery time Over voltage protection Min. 5.4 7.4 19.6 22.0 32.5 ℃ %/ µs VDC 150 % Continuous, automatics recovery Conditions Input to Output Input(Output) to Case Min. 297 MIL-HDBK-217F, Full load www.PDUKE.com Typ. 1600 1000 1 Max. Unit VDC 330 GΩ pF kHz UL60950-1 EN60950-1 IEC60950-1 Copper FR4 PCB Epoxy (UL94 V-0) 16.5g (0.58oz) 3.376 x 106 hrs 1500 363 2014/04/30 LCD10W ENVIRONMENTAL SPECIFICATIONS Parameter Conditions Operating ambient temperature Maximum case temperature Storage temperature range Thermal impedance Min. Without derating With derating Typ. -40 +81 +81 +105 105 +125 -55 Vertical direction by natural convection (20LFM) Without heat-sink With heat-sink Max. 16.18 15.13 Thermal shock Vibration Relative humidity Unit ℃ ℃ ℃ ℃/W MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (3) ESD Radiated immunity Fast transient (4) Surge (4) Conducted immunity Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 1kV 3 Vr.m.s Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: 1. 2. 3. 4. Test by minimum input and constant resistive load. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor between the Trim pin and either the +Vout pin or the -Vout pin. The standard modules meet EN55022 Class A without external components and meet Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE 3 LCD10-48S05W Derating Curve LCD10-48S05W Derating Curve With Heat-sink LCD10-48S05W Efficiency vs. Input Voltage LCD10-48S05W Efficiency vs. Output Load www.PDUKE.com 2014/04/30 LCD10W MECHANICAL DRAWING PIN CONNECTION PIN 1 2 3 4 5 6 SINGLE +Vin -Vin Ctrl +Vout Trim -Vout DUAL +Vin -Vin Ctrl +Vout Common -Vout EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 6 5 RU 5 RD 4 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2014/04/30