ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER GENERAL DESCRIPTION FEATURES The ICS84330 is a general purpose, single output high frequency synthesizer and a member of the HiPerClockS™ HiPerClockS™ family of High Performance Clock Solutions from ICS. The VCO operates at a frequency range of 250MHz to 700MHz. The VCO and output frequency can be programmed using the serial or parallel interfaces to the configuration logic. The output can be configured to divide the VCO frequency by 1, 2, 4, and 8. Output frequency steps from 250KHz to 2MHz can be achieved using a 16MHz crystal depending on the output divider setting. • Fully integrated PLL, no external loop filter requirements ICS • 1 differential 3.3V LVPECL output • Crystal oscillator interface: 10MHz to 25MHz • Output frequency range: 25MHz to 700MHz • VCO range: 250MHz to 700MHz • Parallel or serial interface for programming M and N dividers during power-up • RMS Period jitter: 5ps (maximum) • Cycle-to-cycle jitter: 40ps (maximum) • 3.3V supply voltage • 0°C to 70°C ambient operating temperature • Pin compatible with the MC12430 • Lead-Free/Annealed package available • Industrial temperature information available upon request VEE TEST VCC OSC S_CLOCK 26 S_DATA 27 S_LOAD 1 XTAL2 0 VCCA ÷ 16 FREF_EXT XTAL_SEL XTAL_SEL XTAL1 PLL PHASE DETECTOR 1 17 N0 28 16 28-Lead PLCC V Package 15 11.6mm x 11.4mm x 4.1mm 2 14 body package 3 13 Top View M8 1 M7 12 M4 ICS84330 4 5 M5 M3 M2 VEE TEST VCC S_CLOCK 1 32 31 30 29 28 27 26 25 24 n/c S_DATA 2 23 N1 S_LOAD 3 22 N0 VCCA 4 21 M8 VCCA 5 20 M7 FREF_EXT 6 19 M6 XTAL_SEL 7 18 M5 XTAL1 8 17 9 10 11 12 13 14 15 16 M4 ICS84330 32-Lead LQFP Y package 7mm x 7mm x 1.4mm body package Top View nc M3 M2 M1 M0 nP_LOAD OE XTAL2 www.icst.com/products/hiperclocks.html 1 M6 9 10 11 VCC N0:N1 8 VEE M0:M8 nFOUT VCC TEST FOUT CONFIGURATION INTERFACE LOGIC 7 M1 0 6 M0 FOUT nFOUT nP_LOAD ÷2 N1 OE ÷M ÷2 ÷4 ÷8 ÷1 18 XTAL2 VCO 84330BV VEE XTAL1 S_LOAD S_DATA S_CLOCK nP_LOAD nFOUT VCC 25 24 23 22 21 20 19 OE FREF_EXT FOUT PIN ASSIGNMENT BLOCK DIAGRAM REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER FUNCTIONAL DESCRIPTION NOTE: The functional description that follows describes operation using a 16MHz crystal. Valid PLL loop divider values for different crystal or input frequencies are defined in the Input Frequency Characteristics, Table 6, NOTE 1. latched and the M divider remains loaded until the next LOW transition on nP_LOAD or until a serial event occurs. The TEST output is Mode 000 (shift register out) when operating in the parallel input mode. The relationship between the VCO frequency, the crystal frequency and the M divider is defined as follows: fxtal x fVCO = 2M 16 The ICS84330 features a fully integrated PLL and therefore requires no external components for setting the loop bandwidth. A quartz crystal is used as the input to the on-chip oscillator. The output of the oscillator is divided by 16 prior to the phase detector. With a 16MHz crystal this provides a 1MHz reference frequency. The VCO of the PLL operates over a range of 250MHz to 700MHz. The output of the M divider is also applied to the phase detector. The M value and the required values of M0 through M8 are shown in Table 3B, Programmable VCO Frequency Function Table. Valid M values for which the PLL will achieve lock are defined as 125 ≤ M ≤ 350. The frequency out is defined as follows: fout = fVCO = fxtal x 2M N N 16 The phase detector and the M divider force the VCO output frequency to be 2M times the reference frequency by adjusting the VCO control voltage. Note that for some values of M (either too high or too low), the PLL will not achieve lock. The output of the VCO is scaled by a divider prior to being sent to each of the LVPECL output buffers. The divider provides a 50% output duty cycle. Serial operation occurs when nP_LOAD is HIGH and S_LOAD is LOW. The shift register is loaded by sampling the S_DATA bits with the rising edge of S_CLOCK. The contents of the shift register are loaded into the M divider when S_LOAD transitions from LOW-to-HIGH. The M divide and N output divide values are latched on the HIGH-to-LOW transition of S_LOAD. If S_LOAD is held HIGH, data at the S_DATA input is passed directly to the M divider on each rising edge of S_CLOCK. The serial mode can be used to program the M and N bits and test bits T2:T0. The internal registers T2:T0 determine the state of the TEST output as follows: The programmable features of the ICS84330 support two input modes to program the M divider and N output divider. The two input operational modes are parallel and serial. Figure 1 shows the timing diagram for each mode. In parallel mode the nP_LOAD input is LOW. The data on inputs M0 through M8 and N0 through N1 is passed directly to the M divider and N output divider. On the LOW-to-HIGH transition of the nP_LOAD input, the data is T2 0 0 0 0 1 T1 0 0 1 1 0 T0 0 1 0 1 0 1 1 1 0 1 1 1 0 1 TEST Output Shift Register Out High PLL Reference Xtal ÷ 16 (VCO ÷ M) /2 (non 50% Duty Cycle M divider) fOUT LVCMOS Output Frequency < 200MHz Low (S_CLOCK ÷ M) /2 (non 50% Duty Cycle M divider) fOUT ÷ 4 fOUT fOUT fOUT fOUT fOUT fOUT fOUT S_CLOCK ÷ N divider fOUT SERIAL LOADING S_CLOCK S_DATA T2 t S S_LOAD t T1 T0 N1 N0 M8 M7 M6 M5 M4 M3 M2 M1 M0 H t nP_LOAD S PARALLEL LOADING M0:M8, N0:N1 M, N nP_LOAD t S t H Time FIGURE 1. PARALLEL & SERIAL LOAD OPERATIONS 84330BV www.icst.com/products/hiperclocks.html 2 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER TABLE 1. PIN DESCRIPTIONS Name Type VCCA Power XTAL1, XTAL2 XTAL_SEL Input Pullup OE Input Pullup nP_LOAD Input Pullup M0, M1, M2 M3, M4, M5 M6, M7, M8 Input Pullup N0, N1 Input Pullup VEE Power TEST Output VCC Power nFOUT, FOUT nc FREF_EXT Output Unused Input Description Analog supply pin. Crystal oscillator interface. XTAL1 is an oscillator input. XTAL2 is an oscillator output. Selects between the crystal oscillator or FREF_EXT inputs as the PLL reference source. Selects XTAL inputs when HIGH. Selects FREF_EXT when LOW. LVCMOS / LVTTL interface levels. Output enable. LVCMOS / LVTTL interface levels. Parallel load input. Determines when data present at M8:M0 is loaded into M divider, and when data present at N1:N0 sets the N output divide value. LVCMOS / LVTTL interface levels. M divider inputs. Data latched on LOW-to-HIGH transition of nP_LOAD input. LVCMOS / LVTTL interface levels. Determines N output divider value as defined in Table 3C Function Table. LVCMOS / LVTTL interface levels. Negative supply pins. Test output which is used in the serial mode of operation. LVCMOS / LVTTL interface levels. Core supply pins. Differential output for the synthesizer. 3.3V LVPECL interface levels. Do not connect. Pulldown PLL reference input. LVCMOS / LVTTL interface levels. Clocks the serial data present at S_DATA input into the shift register on the S_CLOCK Input Pulldown rising edge of S_CLOCK. LVCMOS / LVTTL interface levels. Shift register serial input. Data sampled on the rising edge of S_CLOCK. S_DATA Input Pulldown LVCMOS / LVTTL interface levels. Controls transition of data from shift register into the M divider. S_LOAD Input Pulldown LVCMOS / LVTTL interface levels. NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol Parameter CIN Input Capacitance Test Conditions Minimum Typical 4 Maximum Units pF RPULLUP Input Pullup Resistor 51 KΩ RPULLDOWN Input Pulldown Resistor 51 KΩ 84330BV www.icst.com/products/hiperclocks.html 3 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. TABLE 3A. PARALLEL AND 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER SERIAL MODE FUNCTION TABLE Inputs nP_LOAD M N S_LOAD S_CLOCK S_DATA X X X X X X L Data Data X X X ↑ Data Data X X X H X X L ↑ Data H X X ↑ L Data H X X ↓ L Data H X X L X X H X X H NOTE: L = LOW H = HIGH X = Don't care ↑ = Rising edge transition ↓ = Falling edge transition ↑ Data Conditions Reset. M and N bits are all set HIGH. Data on M and N inputs passed directly to M divider and N output divider. TEST mode 000. Data is latched into input registers and remains loaded until next LOW transition or until a serial event occurs. Serial input mode. Shift register is loaded with data on S_DATA on each rising edge of S_CLOCK. Contents of the shift register are passed to the M divider and N output divider. M divide and N output divide values are latched. Parallel or serial input do not affect shift registers. S_DATA passed directly to M divider as it is clocked. TABLE 3B. PROGRAMMABLE VCO FREQUENCY FUNCTION TABLE VCO Frequency (MHz) M Divide 256 128 64 32 16 8 4 2 1 M8 M7 M6 M5 M4 M3 M2 M1 M0 250 125 0 0 1 1 1 1 1 0 1 252 126 0 0 1 1 1 1 1 1 0 254 127 0 0 1 1 1 1 1 1 1 256 128 0 1 0 0 0 0 0 0 0 • • • • • • • • • • • • • • • • • • • • • • 696 348 1 0 1 0 1 1 1 0 0 698 349 1 0 1 0 1 1 1 0 1 700 350 1 0 1 0 1 1 1 1 0 NOTE 1: These M divide values and the resulting frequencies correspond to a crystal frequency of 16MHz. TABLE 3C. PROGRAMMABLE OUTPUT DIVIDER FUNCTION TABLE Inputs N Divider Value Output Frequency (MHz) N1 N0 0 0 2 0 1 4 62.5 175 1 0 8 31.25 87.5 1 1 1 250 700 84330BV Minimum Maximum 125 350 www.icst.com/products/hiperclocks.html 4 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER ABSOLUTE MAXIMUM RATINGS Supply Voltage, VCC Inputs, VI 4.6V -0.5V to VCC + 0.5 V NOTE: Stresses beyond those listed under Absolute Outputs, IO Continuous Current Surge Current 50mA 100mA device. These ratings are stress specifications only. Functional Package Thermal Impedance, θJA 32 Lead LQFP 28 Lead PLCC 47.9°C/W (0 lfpm) 37.8°C/W (0 lfpm) Storage Temperature, TSTG -65°C to 150°C Maximum Ratings may cause permanent damage to the operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Character- istics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 4A. DC POWER SUPPLY CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Minimum Typical Maximum Units VCC Core Supply Voltage Test Conditions 3.135 3.3 3.465 V VCCA Analog Supply Voltage 3.135 3.3 3.465 V ICC Power Supply Current 130 mA ICCA Analog Supply Current 15 mA TABLE 4B. LVCMOS / LVTTL DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Maximum Units VIH Input High Voltage Test Conditions 2 VCC + 0.3 V VIL Input Low Voltage -0.3 0.8 V VCC = VIN = 3.465V 5 µA VCC = VIN = 3.465V 150 µA VOH M0-M8, N0, N1, OE, nP_LOAD, XTAL_SEL Input High Current S_LOAD, S_CLOCK FREF_EXT, S_DATA M0-M8, N0, N1, OE, nP_LOAD, XTAL_SEL Input Low Current S_LOAD, S_CLOCK FREF_EXT, S_DATA Output High Voltage; NOTE 1 VOL Output Low Voltage; NOTE 1 IIH IIL Minimum Typical VCC = 3.465V, VIN = 0V -150 µA VCC = 3.465V, VIN = 0V -5 µA 2.6 V 0.5 V NOTE 1: Outputs terminated with 50Ω to VCC/2. TABLE 4C. LVPECL DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Maximum Units VOH Output High Voltage; NOTE 1 Test Conditions Minimum VCC - 1.4 Typical VCC - 1.0 V V OL Output Low Voltage; NOTE 1 VCC - 2.0 VCC - 1.7 V VSWING Peak-to-Peak Output Voltage Swing 0.6 1.0 V NOTE 1: Outputs terminated with 50Ω to VCC - 2V. 84330BV www.icst.com/products/hiperclocks.html 5 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER TABLE 5. CRYSTAL CHARACTERISTICS Parameter Test Conditions Minimum Mode of Oscillation Typical Maximum Units Fundamental 25 MHz Equivalent Series Resistance (ESR) Frequency 10 70 Ω Shunt Capacitance 7 pF TABLE 6. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Test Conditions fIN Input Frequency XTAL; NOTE 1 Minimum Typical 10 S_CLOCK Maximum Units 25 MHz 50 MHz FREF_EXT; NOTE 2 10 MHz NOTE 1: For the cr ystal frequency range the M value must be set to achieve the minimum or maximum VCO frequency range of 250MHz to 700MHz. Using the minimum frequency of 10MHz, valid values of M are 200 ≤ M ≤ 511. Using the maximum frequency of 25MHz, valid values of M are 80 ≤ M ≤ 224. NOTE 2: Maximum frequency on FREF_EXT is dependent on the internal M counter limitations. See Application Information Section for recommendations on optimizing the performance using the FREF_EXT input. TABLE 7. AC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Test Conditions Minimum Typical Maximum Units FOUT Output Frequency 700 MHz tjit(per) Period Jitter, RMS; NOTE 1, 2 5 ps tjit(cc) Cycle-to-Cycle Jitter; NOTE 1, 2 40 ps tR / tF Output Rise/Fall Time 600 ps tS Setup Time 200 20 ns S_CLOCK to S_LOAD 20 ns M, N to nP_LOAD 20 ns S_DATA to S_CLOCK 20 ns M, N to nP_LOAD 20 tH Hold Time tL PLL Lock Time odc 20% to 80% S_DATA to S_CLOCK Output Duty Cycle ns 10 ms N≠1 45 55 % N = 1, fOUT ≤ 250MHz N = 1, 250MHz < fOUT ≤ 500MHz 45 55 % 40 60 % See Parameter Measurement Information section. Characterized using a XTAL input. NOTE 1: This parameter is defined in accordance with JEDEC Standard 65 NOTE 2: See Applications section. 84330BV www.icst.com/products/hiperclocks.html 6 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER PARAMETER MEASUREMENT INFORMATION 2V VOH VCC, VCCA Qx SCOPE VREF nQx VEE VOL 1σ contains 68.26% of all measurements 2σ contains 95.4% of all measurements 3σ contains 99.73% of all measurements 4σ contains 99.99366% of all measurements 6σ contains (100-1.973x10-7)% of all measurements LVPECL Histogram Reference Point Mean Period (Trigger Edge) (First edge after trigger) -1.3V ± 0.165V PERIOD JITTER 3.3V OUTPUT LOAD AC TEST CIRCUIT nFOUT 80% 80% V FOUT SW I N G ➤ tcycle ➤ n tcycle n+1 20% 20% ➤ Clock Outputs ➤ t R t F t jit(cc) = tcycle n –tcycle n+1 1000 Cycles CYCLE-TO-CYCLE JITTER OUTPUT RISE/FALL TIME nFOUT FOUT Pulse Width t odc = PERIOD t PW t PERIOD OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD 84330BV www.icst.com/products/hiperclocks.html 7 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER APPLICATION INFORMATION POWER SUPPLY FILTERING TECHNIQUES As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS84330 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. V CC and V CCA should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 2 illustrates how a 10Ω resistor along with a 10µF and a .01µF bypass capacitor should be connected to each VCCA pin. 3.3V VCC .01µF 10Ω .01µF 10µF VCCA FIGURE 2. POWER SUPPLY FILTERING TERMINATION FOR LVPECL OUTPUTS drive 50Ω transmission lines. Matched impedance techniques should be used to maximize operating frequency and minimize signal distortion. Figures 3A and 3B show two different layouts which are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations. The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources must be used for functionality. These outputs are designed to 3.3V Zo = 50Ω 125Ω FOUT 125Ω FIN Zo = 50Ω Zo = 50Ω FOUT 50Ω RTT = 1 Z ((VOH + VOL) / (VCC – 2)) – 2 o VCC - 2V Zo = 50Ω RTT 84Ω FIGURE 3A. LVPECL OUTPUT TERMINATION 84330BV FIN 50Ω 84Ω FIGURE 3B. LVPECL OUTPUT TERMINATION www.icst.com/products/hiperclocks.html 8 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER LVCMOS TO XTAL INTERFACE ance trace may be required. The input can function with half swing amplitude. Reducing amplitude from full swing of 3.3V to half swing of about 1.65V can prevent signal interfere with power rail and may reduce noise. Please refer to the LVCMOS driver data sheet and application note for amplitude reduction and termination approach. The XTAL1 input can accept single ended LVCMOS signal through an AC couple capacitor. A general interface diagram is shown in Figure 4. The XTAL2 input can be left floating. The edge rate can be as slow as 10ns. If the incoming signal has sharp edge rate and the signal path is a long trace, proper termination for the driver and controlled characteristic imped- VDD Q1 C1 XTAL1 0.1uF LVCMOS_Driver Figure 4. GENERAL DIAGRAM XTAL2 FOR LVCMOS DRIVER Crystal Input Interface TO XTAL INPUT INTERFACE Cycle-to-Cycle Jitter (ps) 50 40 30 Spec Limit N=1 20 10 0 200 300 400 500 600 700 Output Frequency (MHz) FIGURE 5. CYCLE-TO-CYCLE JITTER VS. fOUT (using a 16MHz XTAL) 84330BV www.icst.com/products/hiperclocks.html 9 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER LAYOUT GUIDELINE The schematic of the ICS84330 layout example used in this layout guideline is shown in Figure 6A. The ICS84330 recommended PCB board layout for this example is shown in Figure 6B. This layout example is used as a general guide- line. The layout in the actual system will depend on the selected component types, the density of the components, the density of the traces, and the stack up of the P.C. board. SP C1 X1 C2 16MHz, 18pF M3 M2 M1 M0 nPLOAD OE SP SP = Spa ce (i .e. no t i n tsta l l e d) M [8 :0 ]= 1 10 01 00 00 (40 0) N[1:0] =00 (Di vi de by 2 ) 11 10 9 8 7 6 5 M4 M5 M6 M7 M8 N0 N1 ICS84330 XTAL1 XTAL_SEL FREF_EXT VCCA S_LOAD S_DATA S_CLOCK VCC VCC M3 M2 M1 M0 nP_LOAD OE XTAL2 12 13 14 15 16 17 18 VCC 4 3 2 1 28 27 26 VEE TEST VCC VEE nFOUT FOUT VCC M4 M5 M6 M7 M8 N2 N1 VCC=3.3 V 19 20 21 22 23 24 25 U1 R7 10 VCCA C11 0.01u C16 10u C3 0.1uF Zo = 50 Ohm RD0 1K RD7 SP RD8 SP RD9 1K RU11 SP nPLoad RD10 SP RU12 1K Fou t = 20 0 M Hz C4 0.1u + Zo = 50 Ohm OE N0 M8 M7 RD1 1K RU10 1K RU9 SP RU8 1K N1 RU7 1K RU1 SP M1 M0 RU0 SP RD6 1K - R1 50 R2 50 RD12 SP R3 50 FIGURE 6A. SCHEMATIC 84330BV OF RECOMMENDED LAYOUT www.icst.com/products/hiperclocks.html 10 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER The following component footprints are used in this layout example: • The differential 50Ω output traces should have the same length. All the resistors and capacitors are size 0603. • Avoid sharp angles on the clock trace. Sharp angle turns cause the characteristic impedance to change on the transmission lines. POWER AND GROUNDING Place the decoupling capacitors C3 and C4, as close as possible to the power pins. If space allows, placement of the decoupling capacitor on the component side is preferred. This can reduce unwanted inductance between the decoupling capacitor and the power pin caused by the via. • Keep the clock traces on the same layer. Whenever possible, avoid placing vias on the clock traces. Placement of vias on the traces can affect the trace characteristic impedance and hence degrade signal integrity. Maximize the power and ground pad sizes and number of vias capacitors. This can reduce the inductance between the power and ground planes and the component power and ground pins. • To prevent cross talk, avoid routing other signal traces in parallel with the clock traces. If running parallel traces is unavoidable, allow a separation of at least three trace widths between the differential clock trace and the other signal trace. The RC filter consisting of R7, C11, and C16 should be placed as close to the VCCA pin as possible. • Make sure no other signal traces are routed between the clock trace pair. CLOCK TRACES • The matching termination resistors should be located as close to the receiver input pins as possible. AND TERMINATION Poor signal integrity can degrade the system performance or cause system failure. In synchronous high-speed digital systems, the clock signal is less tolerant to poor signal integrity than other signals. Any ringing on the rising or falling edge or excessive ring back can cause system failure. The shape of the trace and the trace delay might be restricted by the available space on the board and the component location. While routing the traces, the clock signal traces should be routed first and should be locked prior to routing other signal traces. CRYSTAL The crystal X1 should be located as close as possible to the pins 4 (XTAL1) and 5 (XTAL2). The trace length between the X1 and U1 should be kept to a minimum to avoid unwanted parasitic inductance and capacitance. Other signal traces should not be routed near the crystal traces. X1 C1 C2 U1 GND VCC PIN 2 C11 C16 VCCA PIN 1 VCCA R7 VIA Signals Traces C3 C4 50 Ohm Traces FIGURE 6B. PCB BOARD LAYOUT 84330BV FOR ICS84330 www.icst.com/products/hiperclocks.html 11 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER JITTER REDUCTION FOR FREF_EXT SINGLE END INPUT If the FREF_EXT input is driven by a 3.3V LVCMOS driver, the jitter performance can be improved by reducing the amplitude swing and slowing down the edge rate. Figure 7A shows an amplitude reduction approach for a long trace. The swing will be approximately 0.85V for logic low and 2.5V for logic high (instead of 0V to 3.3V). Figure 7B shows amplitude reduction approach for a short trace. The circuit shown in Figure 7C reduces amplitude swing and also slows down the edge rate by increasing the resistor value. VDD VDD Ro ~ 7 Ohm RS R1 100 Zo = 50 Ohm Td VDD GND 43 R2 100 Driver_LVCMOS FIGURE 7A. AMPLITUDE REDUCTION FOR A TEST_CLK FREF_EXT LONG TRACE VDD VDD R1 200 Ro ~ 7 Ohm VDD RS GND 100 R2 200 Driver_LVCMOS FIGURE 7B. AMPLITUDE REDUCTION FOR A TEST_CLK FREF_EXT SHORT TRACE VDD VDD R1 400 Ro ~ 7 Ohm VDD RS GND 200 R2 400 Driver_LVCMOS FIGURE 7C. EDGE RATE REDUCTION 84330BV BY INCREASING THE www.icst.com/products/hiperclocks.html 12 TEST_CLK FREF_EXT RESISTOR VALUE REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER POWER CONSIDERATIONS This section provides information on power dissipation and junction temperature for the ICS84330. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS84330 is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load. • • Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 145mA = 502.4mW Power (outputs)MAX = 30.2mW/Loaded Output pair If all outputs are loaded, the total power is 1 * 30.2mW = 30.2mW Total Power_MAX (3.465V, with all outputs switching) = 502.4 + 30.2mW = 532.6mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for HiPerClockSTM devices is 125°C. The equation for Tj is as follows: Tj = θJA * Pd_total + TA Tj = Junction Temperature θJA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 31.1°C/W per Table 9A below. Therefore, Tj for an ambient temperature of 70°C with all outputs switching is: 70°C + 0.533W * 31.1°C/W = 86.6°C. This is well below the limit of 125°C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer). TABLE 9A. THERMAL RESISTANCE θJA FOR 28-PIN PLCC, FORCED CONVECTION θJA by Velocity (Linear Feet per Minute) Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 37.8°C/W 31.1°C/W 28.3°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TABLE 9B. THERMAL RESISTANCE θJA FOR 32-PIN LQFP, FORCED CONVECTION θJA by Velocity (Linear Feet per Minute) 0 200 500 Single-Layer PCB, JEDEC Standard Test Boards 67.8°C/W 55.9°C/W 50.1°C/W Multi-Layer PCB, JEDEC Standard Test Boards 47.9°C/W 42.1°C/W 39.4°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. 84330BV www.icst.com/products/hiperclocks.html 13 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 3. Calculations and Equations. The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in the Figure 8. VCC Q1 VOUT RL 50 VCC - 2V FIGURE 8. LVPECL DRIVER CIRCUIT AND TERMINATION To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination voltage of V - 2V. CC • For logic high, VOUT = V OH_MAX (V CC_MAX • -V OH_MAX OL_MAX CC_MAX CC_MAX – 1.0V ) = 1.0V For logic low, VOUT = V (V =V =V CC_MAX – 1.7V ) = 1.7V -V OL_MAX Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = [(V OH_MAX – (V CC_MAX - 2V))/R ] * (V CC_MAX L -V OH_MAX ) = [(2V - (V CC_MAX -V OH_MAX ))/R ] * (V CC_MAX L -V OH_MAX )= [(2V - 1V)/50Ω] * 1V = 20.0mW Pd_L = [(V OL_MAX – (V CC_MAX - 2V))/R ] * (V L CC_MAX -V OL_MAX ) = [(2V - (V CC_MAX -V OL_MAX ))/R ] * (V L CC_MAX -V OL_MAX )= [(2V - 1.7V)/50Ω] * 1.7V = 10.2mW Total Power Dissipation per output pair = Pd_H + Pd_L = 30.2mW 84330BV www.icst.com/products/hiperclocks.html 14 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER RELIABILITY INFORMATION TABLE 10A. θJAVS. AIR FLOW PLCC TABLE FOR 28 LEAD PLCC θJA by Velocity (Linear Feet per Minute) Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 37.8°C/W 31.1°C/W 28.3°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TABLE 10B. θJAVS. AIR FLOW LQFP TABLE FOR 32 LEAD LQFP θJA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 67.8°C/W 47.9°C/W 55.9°C/W 42.1°C/W 50.1°C/W 39.4°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS84330 is: 4442 84330BV www.icst.com/products/hiperclocks.html 15 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER PACKAGE OUTLINE - V SUFFIX FOR 28 LEAD PLCC TABLE 11A. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS SYMBOL MINIMUM MAXIMUM 28 N A 4.19 4.57 A1 2.29 3.05 A2 1.57 2.11 b 0.33 0.53 c 0.19 0.32 D 12.32 12.57 D1 11.43 11.58 D2 4.85 5.56 E 12.32 12.57 E1 11.43 11.58 E2 4.85 5.56 Reference Document: JEDEC Publication 95, MS-018 84330BV www.icst.com/products/hiperclocks.html 16 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER PACKAGE OUTLINE - Y SUFFIX FOR 32 LEAD LQFP TABLE 11B. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS BBA SYMBOL MINIMUM NOMINAL MAXIMUM 32 N A -- -- 1.60 A1 0.05 -- 0.15 A2 1.35 1.40 1.45 b 0.30 0.37 0.45 c 0.09 -- 0.20 D 9.00 BASIC D1 7.00 BASIC D2 5.60 Ref. E 9.00 BASIC E1 7.00 BASIC E2 5.60 Ref. 0.80 BASIC e L 0.45 0.60 0.75 θ 0° -- 7° ccc -- -- 0.10 Reference Document: JEDEC Publication 95, MS-026 84330BV www.icst.com/products/hiperclocks.html 17 REV. B JULY 26, 2004 ICS84330 Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER TABLE 12. ORDERING INFORMATION Part/Order Number Marking Package Count Temperature ICS84330BV ICS84330BV 28 Lead PLCC 38 per Tube 0°C to 70°C ICS84330BVT ICS84330BV 28 Lead PLCC on Tape and Reel 500 0°C to 70°C ICS84330BY ICS84330BY 32 Lead LQFP 250 per Tray 0°C to 70°C ICS84330BYT ICS84330BY 32 Lead LQFP on Tape and Reel 1000 0°C to 70°C ICS84330BYLN ICS84330BYLN 250 per Tray 0°C to 70°C ICS84330BYLNT ICS84330BYLN 32 Lead "Lead Free/Annealed" LQFP 32 Lead "Lead Free/Annealed" LQFP on Tape and Reel 1000 0°C to 70°C The aforementioned trademark, HiPerClockS™ is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 84330BV www.icst.com/products/hiperclocks.html 18 REV. B JULY 26, 2004 Integrated Circuit Systems, Inc. ICS84330 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER REVISION HISTORY SHEET Rev Table Page 2 T4A 5 A 9 10 1 8 10 1 Figure 7A Schematic Layout - revised, changed N[1:0]-01 to N[1:0}=00. Added C1 value (18p) and C2 value (22p). Block Diagram, replaced N with values. Deleted Cr ystal Input Interface section; external tune up capacitor not required. Revised Figure 6A, Schematic of Recommended Layout diagram. General Description & Features - changed VCO min. from 200MHz to 250MHz and replaced throughout the datasheet in (Functional Description pg2, T3C Program. Output Divider Func. Table pg4, and T6 Input Freq Charac. pg6). T2 3 Pin Characteristics Table - changed CIN 4pF max. to 4pF typical. T3B 4 Prog. VCO Freq. Func. Table - replaced VCO Frequency 200MHz to 206MHz with 250MHz to 256MHz. Replaced M Divide 100 to 103 to 125 to 128. Adjusted Logic High and Logic Low data. 5 Absolute Maximum Rating - changed Outputs VO and rating to IO with Continous and Surge ratings. Ordering Information Table - added "Lead Free/Annealed" par t number. Updated format throughout data sheet. A B B 84330BV Description of Change Switched S_DATA and S_CLOCK labels in Figure 1, CLK_EN Timing Diagram. DC Power Supply table - changed ICC Parameter to read Power.. from Core... Added "LVCMOS to XTAL Interface" section. T12 18 www.icst.com/products/hiperclocks.html 19 Date 1/23/03 3/24/03 5/5/03 7/26/04 REV. B JULY 26, 2004