TI1 BQ27520-G4 System-side impedance track fuel gauge Datasheet

Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
bq27520-G4 System-Side Impedance Track™ Fuel Gauge With Integrated LDO
1 Features
2
•
•
•
•
•
1
•
•
•
Single-Series Cell Li-Ion Battery Fuel Gauge
Resides on System Board
– Integrated 2.5 VDC LDO
– External Low-Value 10-mΩ Sense Resistor
Patented Impedance Track™ Technology
– Adjusts for Battery Aging, Self-Discharge,
Temperature, and Rate Changes
– Reports Remaining Capacity, State-of-Charge
(SOC), and Time-to-Empty
– Optional Smoothing Filter
– Battery State-of-Health (Aging) Estimation
– Supports Embedded or Removable Packs with
up to 32A hr Capacity
– Accommodates Pack Swapping With 2
Separate Battery Profiles
Microcontroller Peripheral Supports:
– 400-kHz I2C Serial Interface
– 32 Bytes of Scratch-Pad FLASH NVM
– Battery Low Digital Output Warning
– Configurable SOC Interrupts
– External Thermistor, Internal Sensor, or Hostreported Temperature Options
Tiny 15-pin, 2610 × 1956 µm, 0.5-mm pitch
NanoFree™ (DSBGA) Package
3
Applications
Smartphones, Feature Phones, and Tablets
Digital Still and Video Cameras
Handheld Terminals
MP3 or Multimedia Players
Description
The Texas Instruments bq27520-G4 system-side LiIon battery fuel gauge is a microcontroller peripheral
that provides fuel gauging for single-cell Li-Ion battery
packs.
The
device
requires
little
system
microcontroller firmware development. The fuel
gauge resides on the main board of the system and
manages an embedded battery (non-removable) or a
removable battery pack.
The fuel gauge uses the patented Impedance
Track™ algorithm for fuel gauging, and provides
information such as remaining battery capacity
(mAh), state-of-charge (%), run-time to empty
(minimum), battery voltage (mV), temperature (°C),
and state of health (%).
Battery fuel gauging requires only PACK+ (P+),
PACK– (P–), and optional Thermistor (T) connections
to a removable battery pack or embedded battery
circuit. The device uses a 15-ball NanoFree™
(DSBGA) package in the nominal dimensions of 2610
× 1956 µm with 0.5-mm lead pitch. It is ideal for
space-constrained applications.
Device Information (1)
PART NUMBER
bq27520-G4
(1)
PACKAGE
DSBGA (15)
BODY SIZE (NOM)
2.610 mm x 1.956 mm
For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application Diagram
Host System
Single Cell Li-lon
Battery Pack
VCC
CE
Power
Management
Controller
I2C
LDO
PACK+
Battery
Low
Voltage
Sense
DATA
Temp
Sense
BAT_GD
PROTECTION
IC
T
PACK-
FETs
CHG
DSG
Current
Sense
SOC_INT
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
5
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
5
5
5
5
6
6
6
6
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics: Supply Current.................
Digital Input and Output DC Characteristics .............
Power-on Reset ........................................................
2.5-V LDO Regulator ................................................
Internal Clock Oscillators ..........................................
ADC (Temperature and Cell Measurement)
Characteristics ...........................................................
7.11 Integrating ADC (Coulomb Counter)
Characteristics ...........................................................
7.12 Data Flash Memory Characteristics........................
7.13 I2C-Compatible Interface Communication Timing
Requirements.............................................................
7
7
7
8
7.14 Typical Characteristics ............................................ 9
8
Detailed Description ............................................ 10
8.1
8.2
8.3
8.4
8.5
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Programming...........................................................
10
11
12
12
17
Application and Implementation ........................ 21
9.1 Application Information............................................ 21
9.2 Typical Application .................................................. 22
10 Power Supply Recommendations ..................... 26
10.1 Power Supply Decoupling ..................................... 26
11 Layout................................................................... 26
11.1 Layout Guidelines ................................................. 26
11.2 Layout Example .................................................... 27
12 Device and Documentation Support ................. 28
12.1
12.2
12.3
12.4
12.5
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
28
28
28
28
28
13 Mechanical, Packaging, and Orderable
Information ........................................................... 28
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (August 2013) to Revision B
Page
•
Changed 32 Ahr to 14500-mAh ............................................................................................................................................. 1
•
Deleted minimum and maximum values for Power-on reset hysteresis ................................................................................ 6
•
Added Device Information table, ESD Ratings table, Feature Description section, Device Functional Modes,
Programming section, Application and Implementation section, Power Supply Recommendations section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information. ......................................... 12
•
Changed Figure 6 ................................................................................................................................................................ 14
•
Added Figure 7 .................................................................................................................................................................... 15
Changes from Original (November 2012) to Revision A
Page
•
Aligned package description throughout datasheet................................................................................................................ 1
•
Removed Ordering information table...................................................................................................................................... 4
2
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
5 Device Comparison Table
PRODUCTION
PART NO. (1)
bq27520YZFR-G4
bq27520YZFT-G4
(1)
(2)
PACKAGE (2)
TA
COMMUNICATION
FORMAT
DSBGA-15
–40°C to 85°C
I2C (1)
TAPE AND REEL
QUANTITY
3000
250
2
bq27520-G4 is shipped in I C mode
For the most current package and ordering information, see the Package Option Addendum at the end of this document; or, see the TI
website at www.ti.com.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
3
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
6 Pin Configuration and Functions
YZF Package
15-Pin DSBGA
(TOP VIEW)
B3
C3
D3
E3
E3
D3
C3
B3
A3
A2
B2
C2
D2
E2
E2
D2
C2
B2
A2
A1
B1
C1
D1
E1
E1
D1
C1
B1
A1
A3
E
(BOTTOM VIEW)
xx
xx
Pin A1
Index Area
D
DIM
MIN
TYP
MAX
D
2580
2610
2640
E
1926
1956
1986
UNITS
m
Pin Functions
PIN
NAME
NUMBER
TYPE (1)
DESCRIPTION
BAT
E2
I
Cell-voltage measurement input. ADC input. Recommend 4.8 V maximum for conversion
accuracy.
BAT_GD
B2
O
Battery Good push-pull indicator output. Active low and output disabled by default. Polarity
is configured via Op Config [BATG_POL] and the output is enabled via OpConfig C
[BATGSPUEN].
BAT_LOW
C3
O
Battery Low push-pull output indicator. Active high and output enabled by default. Polarity is
configured via Op Config [BATL_POL] and the output is enabled via OpConfig C
[BATLSPUEN].
BI/TOUT
E3
IO
Battery-insertion detection input. Power pin for pack thermistor network. Thermistormultiplexer control pin. Use with pullup resistor >1 MΩ (1.8 MΩ, typical).
CE
D2
I
Chip Enable. Internal LDO is disconnected from REGIN when driven low.
Note: CE has an internal ESD protection diode connected to REGIN. Recommend
maintaining VCE ≤ VREGIN under all conditions.
REGIN
E1
P
Regulator input. Decouple with 0.1-μF ceramic capacitor to VSS.
SCL
A3
I
Slave I2C serial communications clock input line for communication with system (Master).
Open-drain IO. Use with 10-kΩ pullup resistor (typical).
SDA
B3
IO
Slave I2C serial communications data line for communication with system (Master). Opendrain IO. Use with 10-kΩ pullup resistor (typical).
SOC_INT
A2
O
SOC state interrupts output. Generates a pulse under the conditions specified in the
bq27520-G4 Technical Reference Manual, SLUUA35. Open drain output.
SRN
B1
IA
Analog input pin connected to the internal coulomb counter with a Kelvin connection where
SRN is nearest the VSS connection. Connect to 5-mΩ to 20-mΩ sense resistor.
SRP
A1
IA
Analog input pin connected to the internal coulomb counter with a Kelvin connection where
SRP is nearest the PACK– connection. Connect to 5-mΩ to 20-mΩ sense resistor.
TS
D3
IA
Pack thermistor voltage sense (use 103AT-type thermistor). ADC input.
VCC
D1
P
Regulator output and bq27520-G4 processor power. Decouple with 1-μF ceramic capacitor
to VSS.
VSS
C1, C2
P
Device ground
(1)
4
IO = Digital input-output, IA = Analog input, P = Power connection
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
7 Specifications
7.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
VREGIN
Regulator input
MIN
MAX
UNIT
–0.3
5.5
V
–0.3
6.0
(2)
V
VCE
CE input pin
–0.3
VREGIN + 0.3
V
VCC
Supply voltage
–0.3
2.75
V
VIOD
Open-drain I/O pins (SDA, SCL, SOC_INT)
–0.3
5.5
V
VBAT
BAT input pin
–0.3
5.5
V
–0.3
VI
Input voltage to all other pins
(BI/TOUT, TS, SRP, SRN, BAT_LOW, BAT_GD)
–0.3
TA
Operating free-air temperature
Tstg
Storage temperature
(1)
(2)
6.0
(2)
V
VCC + 0.3
V
–40
85
°C
–65
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Condition not to exceed 100 hours at 25°C lifetime.
7.2 ESD Ratings
VALUE
VESD
(1)
Electrostatic discharge
Human-body model (HBM)
(1)
All pins except E2
2000
Pin E2
1500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
TA = –40°C to 85°C, VREGIN = VBAT = 3.6 V (unless otherwise noted)
MIN
No operating restrictions
VREGIN
Supply voltage
CREGIN
External input capacitor for internal
LDO between REGIN and VSS
CLDO25
External output capacitor for internal
LDO between VCC and VSS
tPUCD
Power-up communication delay
No flash writes
Nominal capacitor values specified.
Recommend a 5% ceramic X5Rtype capacitor located close to the
device.
NOM
MAX
2.8
4.5
2.45
2.8
0.47
UNIT
V
0.1
μF
1
μF
250
ms
7.4 Thermal Information
over operating free-air temperature (unless otherwise noted)
bq27520-G4
THERMAL METRIC
(1)
YZF (DSBGA)
UNIT
15 PINS
RθJA
Junction-to-ambient thermal resistance
70
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
17
°C/W
RθJB
Junction-to-board thermal resistance
20
°C/W
ψJT
Junction-to-top characterization parameter
1
°C/W
ψJB
Junction-to-board characterization parameter
18
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
NA
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
5
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
7.5 Electrical Characteristics: Supply Current
TA = 25°C and VREGIN = VBAT = 3.6 V (unless otherwise noted)
PARAMETER
(1)
ICC
ISLP+
(1)
TEST CONDITIONS
TYP
MAX
UNIT
Normal operating mode current
Fuel gauge in NORMAL mode
ILOAD > Sleep current
118
μA
Snooze operating mode current
Fuel gauge in SNOOZE mode
ILOAD < Sleep current
62
μA
23
μA
8
μA
ISLP
(1)
Low-power storage mode current
Fuel gauge in SLEEP mode
ILOAD < Sleep current
IHIB
(1)
Hibernate operating mode current
Fuel gauge in HIBERNATE mode
ILOAD < Hibernate current
(1)
MIN
Specified by design. Not production tested.
7.6 Digital Input and Output DC Characteristics
TA = –40°C to 85°C, typical values at TA = 25°C and VREGIN = 3.6 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
VOL
Output voltage, low (SCL, SDA,
SOC_INT, BAT_LOW, BAT_GD)
IOL = 3 mA
VOH(PP)
Output voltage, high (BAT_LOW,
BAT_GD)
IOH = –1 mA
VOH(OD)
Output voltage, high (SDA, SCL,
SOC_INT)
External pullup resistor connected to VCC
Input voltage, low (BI/TOUT)
Input voltage, high (BI/TOUT)
VIL(CE)
Input voltage, low (CE)
VIH(CE)
Input voltage, high (CE)
Ilkg
(1)
(1)
UNIT
V
VCC – 0.5
BAT INSERT CHECK mode active
Input voltage, high (SDA, SCL)
VIH
MAX
0.4
Input voltage, low (SDA, SCL)
VIL
TYP
V
VCC – 0.5
–0.3
0.6
–0.3
0.6
1.2
BAT INSERT CHECK mode active
1.2
VCC + 0.3
0.8
VREGIN = 2.8 to 4.5 V
2.65
Input leakage current (IO pins)
0.3
V
V
V
μA
Specified by design. Not production tested.
7.7 Power-on Reset
TA = –40°C to 85°C, typical values at TA = 25°C and VREGIN = 3.6 V (unless otherwise noted)
PARAMETER
VIT+
Positive-going battery voltage input at VCC
VHYS
Power-on reset hysteresis
MIN
TYP
MAX
2.05
2.15
2.20
115
UNIT
V
mV
7.8 2.5-V LDO Regulator
TA = –40°C to 85°C, CLDO25 = 1 μF, VREGIN = 3.6 V (unless otherwise noted)
PARAMETER
VREG25
(1)
TEST CONDITIONS
Regulator output voltage (VCC)
MIN
TYP
MAX
2.8 V ≤ VREGIN ≤ 4.5 V, IOUT ≤ 16 mA (1)
2.3
2.5
2.6
2.45 V ≤ VREGIN < 2.8 V (low battery),
IOUT ≤ 3 mA
2.3
UNIT
V
V
LDO output current, IOUT, is the total load current. LDO regulator should be used to power internal fuel gauge only.
7.9 Internal Clock Oscillators
TA = –40°C to 85°C, 2.4 V < VCC < 2.6 V; typical values at TA = 25°C and VCC = 2.5 V (unless otherwise noted)
PARAMETER
MIN
TYP
MAX
UNIT
fOSC
High frequency oscillator
8.389
MHz
fLOSC
Low frequency oscillator
32.768
kHz
6
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
7.10 ADC (Temperature and Cell Measurement) Characteristics
TA = –40°C to 85°C, 2.4 V < VCC < 2.6 V; typical values at TA = 25°C and VCC = 2.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VADC1
Input voltage range (TS)
VSS – 0.125
2
V
VADC2
Input voltage range (BAT)
VSS – 0.125
5
V
VIN(ADC)
Input voltage range
0.05
1
GTEMP
Internal temperature sensor
voltage gain
tADC_CONV
Conversion time
–2
Resolution
VOS(ADC)
(1)
Effective input resistance (TS)
ZADC2
(1)
Effective input resistance (BAT)
Ilkg(ADC)
(1)
ms
15
bits
1
ZADC1
(1)
125
14
Input offset
V
mV/°C
mV
8
Device not measuring cell voltage
MΩ
8
Device measuring cell voltage
MΩ
100
kΩ
Input leakage current
μA
0.3
Specified by design. Not tested in production.
7.11 Integrating ADC (Coulomb Counter) Characteristics
TA = –40°C to 85°C, 2.4 V < VCC < 2.6 V; typical values at TA = 25°C and VCC = 2.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VSR
Input voltage range,
V(SRP) and V(SRN)
VSR = V(SRP) – V(SRN)
tSR_CONV
Conversion time
Single conversion
Resolution
Input offset
INL
Integral nonlinearity error
Ilkg(SR)
(1)
(1)
MAX
UNIT
0.125
V
1
s
15
bits
μV
10
±0.007
Effective input resistance
(1)
TYP
14
VOS(SR)
ZIN(SR)
MIN
–0.125
±0.034
% FSR
2.5
MΩ
Input leakage current
μA
0.3
Specified by design. Not tested in production.
7.12 Data Flash Memory Characteristics
TA = –40°C to 85°C, 2.4 V < VCC < 2.6 V; typical values at TA = 25°C and VCC = 2.5 V (unless otherwise noted)
PARAMETER
tDR
(1)
Data retention
Flash-programming write cycles (1)
tWORDPROG
(1)
ICCPROG
(1)
tDFERASE
tIFERASE
(1)
tPGERASE
(1)
(1)
(1)
MIN
TYP
MAX
UNIT
10
Years
20,000
Cycles
Word programming time
Flash-write supply current
5
2
ms
10
mA
Data flash master erase time
200
ms
Instruction flash master erase time
200
ms
20
ms
Flash page erase time
Specified by design. Not production tested
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
7
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
7.13 I2C-Compatible Interface Communication Timing Requirements
TA = –40°C to 85°C, 2.4 V < VCC < 2.6 V; typical values at TA = 25°C and VCC = 2.5 V (unless otherwise noted)
MIN
NOM
MAX
UNIT
tr
SCL or SDA rise time
300
ns
tf
SCL or SDA fall time
300
ns
tw(H)
SCL pulse duration (high)
600
ns
tw(L)
SCL pulse duration (low)
1.3
μs
tsu(STA)
Setup for repeated start
600
ns
td(STA)
Start to first falling edge of SCL
600
ns
tsu(DAT)
Data setup time
100
ns
th(DAT)
Data hold time
0
ns
tsu(STOP)
Setup time for stop
t(BUF)
Bus free time between stop and start
fSCL
Clock frequency
(1)
600
ns
66
μs
(1)
400
kHz
If the clock frequency (fSCL) is > 100 kHz, use 1-byte write commands for proper operation. All other transactions types are supported at
400 kHz. (See I2C Interface and I2C Command Waiting Time).
Figure 1. I2C-Compatible Interface Timing Diagrams
8
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
7.14 Typical Characteristics
8.8
VREGIN = 2.7 V
VREGIN = 4.5 V
2.6
fOSC - High Frequency Oscillator (MHz)
VREG25 - Regulator Output Voltage (V)
2.65
2.55
2.5
2.45
2.4
2.35
8.7
8.6
8.5
8.4
8.3
8.2
8.1
8
-40
Temperature (qC)
-20
0
20
40
Temperature (qC)
D001
34
5
33.5
4
33
32.5
32
31.5
31
30.5
30
-40
-20
0
20
40
Temperature (qC)
60
80
100
100
D002
3
2
1
0
-1
-2
-3
-4
-5
-30
-20
D003
Figure 4. Low-Frequency Oscillator Frequency vs.
Temperature
80
Figure 3. High-Frequency Oscillator Frequency vs.
Temperature
Reported Temperature Error (qC)
fLOSC - Low Frequency Oscillator (kHz)
Figure 2. Regulator Output Voltage vs. Temperature
60
-10
0
10
20
30
Temperature (qC)
40
50
60
D004
Figure 5. Reported Internal Temperature Measurement vs.
Temperature
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
9
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
8 Detailed Description
8.1 Overview
The bq27520-G4 fuel gauge accurately predicts the battery capacity and other operational characteristics of a
single Li-based rechargeable cell. It can be interrogated by a system processor to provide cell information, such
as time-to-empty (TTE), state-of-charge (SOC), and SOC interrupt signal to the host.
Information is accessed through a series of commands, called Standard Commands. Further capabilities are
provided by the additional Extended Commands set. Both sets of commands, indicated by the general format
Command( ), are used to read and write information contained within the device control and status registers, as
well as its data flash locations. Commands are sent from system to gauge using the I2C serial communications
engine, and can be executed during application development, system manufacture, or end-equipment operation.
Cell information is stored in the device in non-volatile flash memory. Many of these data flash locations are
accessible during application development. They cannot generally be accessed directly during end-equipment
operation. Access to these locations is achieved by either use of the companion evaluation software, through
individual commands, or through a sequence of data-flash-access commands. To access a desired data flash
location, the correct data flash subclass and offset must be known.
The key to the high-accuracy gas gauging prediction is Texas Instruments proprietary Impedance Track™
algorithm. This algorithm uses cell measurements, characteristics, and properties to create state-of-charge
predictions that can achieve less than 1% error across a wide variety of operating conditions and over the
lifetime of the battery.
The fuel gauge measures charge and discharge activity by monitoring the voltage across a small-value series
sense resistor (5 mΩ to 20 mΩ, typical) located between the system VSS and the battery PACK– terminal. When
a cell is attached to the device, cell impedance is learned based on cell current, cell open-circuit voltage (OCV),
and cell voltage under loading conditions.
The external temperature sensing is optimized with the use of a high-accuracy negative temperature coefficient
(NTC) thermistor with R25 = 10.0 kΩ ±1%. B25/85 = 3435K ± 1% (such as Semitec NTC 103AT). Alternatively,
the fuel gauge can also be configured to use its internal temperature sensor or receive temperature data from the
host processor. When an external thermistor is used, a 18.2-kΩ pullup resistor between the BI/TOUT and TS
pins is also required. The fuel gauge uses temperature to monitor the battery-pack environment, which is used
for fuel gauging and cell protection functionality.
To minimize power consumption, the device has different power modes: NORMAL, SNOOZE, SLEEP,
HIBERNATE, and BAT INSERT CHECK. The fuel gauge automatically changes modes depending upon the
occurrence of specific events, though a system processor can initiate some of these modes directly.
For complete operational details, see bq27520-G4 Technical Reference Manual, SLUUA35.
NOTE
The following formatting conventions are used in this document:
Commands: italics with parentheses( ) and no breaking spaces, for example, Control( ).
Data Flash: italics, bold, and breaking spaces, for example, Design Capacity.
Register bits and flags: italics with brackets [ ], for example, [TDA]
Data flash bits: italics, bold, and brackets [ ], for example, [LED1]
Modes and states: ALL CAPITALS, for example, UNSEALED mode.
10
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
8.2 Functional Block Diagram
REGIN
LDO
POR
2.5 V
VCC
HFO
BAT
CC
HFO
SRN
LFO
HFO/128
4R
HFO/128
SRP
MUX
ADC
R
Wake
Comparator
TS
Internal
Temp
Sensor
BI/TOUT
HFO/4
SDA
SOCINT
22
I2C Slave
Engine
Instruction
ROM
22
CPU
VSS
SCL
I/O
Controller
Instruction
FLASH
BAT_LOW
8
Wake
and
Watchdog
Timer
GP Timer
and
PWM
8
BAT_GD
Data
SRAM
Data
FLASH
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
11
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
8.3 Feature Description
The bq27520-G4 measures the voltage, temperature, and current to determine battery capacity and state-ofcharge (SOC) based on the patented Impedance Track™ algorithm (Refer to Application Report, Theory and
Implementation of Impedance Track Battery Fuel-Gauging Algorithm, SLUA450 for more information). The
bq27520-G4 monitors charge and discharge activity by sensing the voltage across a small-value resistor (5 mΩ
to 20 mΩ typical) between the SRP and SRN pins and in series with the battery. By integrating charge passing
through the battery, the battery’s SOC is adjusted during battery charge or discharge. Battery capacity is found
by comparing states of charge before and after applying the load with the amount of charge passed. When a
system load is applied, the impedance of the battery is measured by comparing the open circuit voltage (OCV)
obtained from a predefined function for present SOC with the measured voltage under load. Measurements of
OCV and charge integration determine chemical state-of-charge and chemical capacity (Qmax). The initial Qmax
values are taken from a cell manufacturers' data sheet multiplied by the number of parallel cells. It is also used
for the value in Design Capacity. The bq27520-G4 acquires and updates the battery-impedance profile during
normal battery usage. It uses this profile, along with SOC and the Qmax value, to determine
FullChargeCapacity( ) and StateOfCharge( ), specifically for the present load and temperature.
FullChargeCapacity( ) is reported as capacity available from a fully charged battery under the present load and
temperature until Voltage( ) reaches the Terminate Voltage. NominalAvailableCapacity( ) and
FullAvailableCapacity( ) are the uncompensated (no or light load) versions of RemainingCapacity( ) and
FullChargeCapacity( ), respectively. The bq27520-G4 has two Flags( ) bits and two pins to warn the host if the
battery’s SOC has fallen to critical levels. If RemainingCapacity( ) falls below the first capacity threshold specified
by SOC1 Set Threshold, the Flags ( ) [SOC1] bit is set and is cleared if RemainingCapacity( ) rises above the
SOC1 Clear Threshold. If enabled via OpConfig C [BATLSPUEN], the BAT_LOW pin reflects the status of the
[SOC1] flag bit. If enabled by OpConfig B [BL_INT], the SOC_INT will toggle upon a state change of the [SOC1]
flag bit. As Voltage( ) falls below the SysDown Set Volt Threshold, the Flags( ) [SYSDOWN] bit is set and
SOC_INT will toggle once to provide a final warning to shut down the system. As Voltage( ) rises above
SysDown Clear Voltage the [SYSDOWN] bit is cleared and SOC_INT will toggle once to signal the status
change. Additional details are found in the bq27520-G4 Technical Reference Manual, SLUUA35.
8.4 Device Functional Modes
8.4.1 Power Modes
The fuel gauge has different power modes:
• BAT INSERT CHECK: The BAT INSERT CHECK mode is a powered-up, but low-power halted, state where
the fuel gauge resides when no battery is inserted into the system.
• NORMAL: In NORMAL mode, the fuel gauge is fully powered and can execute any allowable task.
• SLEEP: In SLEEP mode, the fuel gauge turns off the high-frequency oscillator and operates in a reducedpower state, periodically taking measurements and performing calculations.
• SLEEP+: In SLEEP+ mode, both low-frequency and high-frequency oscillators are active. Although the
SLEEP+ mode has higher current consumption than the SLEEP mode, it is also a reduced power mode.
• HIBERNATE: In HIBERNATE mode, the fuel gauge is in a low power state, but can wake up by
communication or certain I/O activity.
The relationship between these modes is shown in Figure 6 and Figure 7.
8.4.1.1 BAT INSERT CHECK Mode
This mode is a halted-CPU state that occurs when an adapter, or other power source, is present to power the
fuel gauge (and system), but no battery has been detected. When battery insertion is detected, a series of
initialization activities begin, which include: OCV measurement, setting the Flags() [BAT_DET] bit, and selecting
the appropriate battery profiles.
Some commands, issued by a system processor, can be processed while the fuel gauge is halted in this mode.
The gauge wakes up to process the command, then returns to the halted state awaiting battery insertion.
8.4.1.2 NORMAL Mode
The fuel gauge is in NORMAL mode when not in any other power mode. During this mode, AverageCurrent() ,
Voltage() , and Temperature() measurements are taken, and the interface data set is updated. Decisions to
change states are also made. This mode is exited by activating a different power mode.
12
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
Device Functional Modes (continued)
Because the gauge consumes the most power in NORMAL mode, the Impedance Track algorithm minimizes the
time the fuel gauge remains in this mode.
8.4.1.3 SLEEP Mode
SLEEP mode is entered automatically if the feature is enabled (Op Config [SLEEP] = 1) and AverageCurrent()
is below the programmable level Sleep Current. Once entry into SLEEP mode has been qualified, but prior to
entering it, the fuel gauge performs a coulomb counter autocalibration to minimize offset.
During SLEEP mode, the fuel gauge periodically takes data measurements and updates its data set. However, a
majority of its time is spent in an idle condition.
The fuel gauge exits SLEEP mode if any entry condition is broken, specifically when:
• AverageCurrent() rises above Sleep Current, or
• A current in excess of IWAKE through RSENSE is detected.
In the event that a battery is removed from the system while a charger is present (and powering the gauge),
Impedance Track updates are not necessary. Hence, the fuel gauge enters a state that checks for battery
insertion and does not continue executing the Impedance Track algorithm.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
13
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
Device Functional Modes (continued)
Exit From HIBERNATE
Battery Removed
POR
BAT INSERT CHECK
Exit From HIBERNATE
Communication Activity
AND Comm address is for bq27531
bq27531 clears CONTROL_STATUS
[HIBERNATE] = 0
Recommend Host also set
CONTROL_STATUS
[HEBERNATE] = 0
Check for battery insertion
from HALT state.
No gauging
Entry To NORMAL
Flags [BAT_DET] = 1
Exit From NORMAL
Flags [BAT_DET] = 0
NORMAL
Entry To SLEEP+
Operation Configuration [SLEEP] = 1
AND
CONTROL_STAUS [SNOOZE] = 1]
AND
Ι AverageCurrent ( ) Ι < Sleep Current
Flags [BAT_DET] = 0
Fuel gauging and data
updated every second
Exit From SLEEP
Flags [BAT_DET] = 0
Exit From SLEEP
Ι AverageCurrent ( ) Ι > Sleep Current
OR
Current is detected above Ι WAKE
Exit From SLEEP+
Any communication to the gauge
OR
Ι AverageCurrent ( ) Ι > Sleep Current
OR
Current is detected above Ι WAKE
SLEEP+
Entry To SLEEP+
Operation Configuration [SLEEP] = 1
Fuel gauging and data
updated every 20 seconds.
Both LFO and HFO are ON.
AND
Ι AverageCurrent ( ) Ι < Sleep Current
AND
CONTROL_STAUS [SNOOZE] = 0
Entry to SLEEP+
CONTROL_STATUS [SNOOZE] = 1
Entry to SLEEP
CONTROL_STATUS [SNOOZE] = 0
SLEEP
Fuel gauging and data
updated every 20 seconds.
(LFO ON and HFO OFF)
Exit From WAIT_HIBERNATE
Host must set CONTROL_STATUS
[HIBERNATE] = 0
AND
VCELL < Hibernate Voltage
To WAIT_HIBERNATE
System Sleep
Exit From SLEEP
Host has set CONTROL_STATUS
[HIBERNATE] = 1
OR
VCELL < Hibernate Voltage
Figure 6. Power Mode Diagram—System Sleep
14
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
Device Functional Modes (continued)
POR
Exit From HIBERNATE
Battery Removed
Exit From HIBERNATE
Communication Activity
AND Comm address is for bq27531
bq27531 clears CONTROL_STATUS
[HIBERNATE] = 0
Recommend Host also set
CONTROL_STATUS
[HEBERNATE] = 0
Exit From SLEEP
Flags [BAT_DET] = 0
BAT INSERT CHECK
Check for battery insertion
from HALT state.
No gauging
Entry To NORMAL
Flags [BAT_DET] = 1
Flags [BAT_DET] = 0
Exit From NORMAL
Flags [BAT_DET] = 0
NORMAL
Fuel gauging and data
updated every second.
HIBERNATE
Wakeup From HIBERNATE
Communication Activity
AND
Comm address is not for
bq27531
Disable all bq27531
subcircuits.
Exit From WAIT_HIBERNATE
Host must set CONTROL_STATUS
[HIBERNATE] = 0
AND
VCELL < Hibernate Voltage
To SLEEP
WAIT_HIBERNATE
Exit From WAIT_HIBERNATE
Cell relaxed
AND
Ι AverageCurrent () Ι < Hibernate
Current
OR
Cell relaxed
AND
VCELL < Hibernate Voltage
Fuel gauging and data
updated every 20 seconds.
Exit From SLEEP
Host has set CONTROL_STATUS
[HIBERNATE] = 1
OR
VCELL < Hibernate Voltage
System Shutdown
Figure 7. Power Mode Diagram—System Shutdown
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
15
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
Device Functional Modes (continued)
8.4.2 SLEEP+ Mode
Compared to the SLEEP mode, SLEEP+ mode has the high-frequency oscillator in operation. The
communication delay could be eliminated. The SLEEP+ mode is entered automatically if the feature is enabled
(CONTROL_STATUS [SNOOZE] = 1) and AverageCurrent() is below the programmable level Sleep Current.
During SLEEP+ mode, the fuel gauge periodically takes data measurements and updates its data set. However,
a majority of its time is spent in an idle condition.
The fuel gauge exits SLEEP+ mode if any entry condition is broken, specifically when:
• Any communication activity with the gauge, or
• AverageCurrent() rises above Sleep Current , or
• A current in excess of IWAKE through RSENSE is detected.
8.4.3 HIBERNATE Mode
HIBERNATE mode should be used when the system equipment needs to enter a low-power state, and minimal
gauge power consumption is required. This mode is ideal when system equipment is set to its own HIBERNATE,
SHUTDOWN, or OFF mode.
Before the fuel gauge can enter HIBERNATE mode, the system must set the CONTROL_STATUS
[HIBERNATE] bit. The gauge waits to enter HIBERNATE mode until it has taken a valid OCV measurement and
the magnitude of the average cell current has fallen below Hibernate Current. The gauge can also enter
HIBERNATE mode if the cell voltage falls below Hibernate Voltage and a valid OCV measurement has been
taken. The gauge remains in HIBERNATE mode until the system issues a direct I2C command to the gauge or a
POR occurs. Any I2C communication that is not directed to the gauge does not wake the gauge.
It is the responsibility of the system to wake the fuel gauge after it has gone into HIBERNATE mode. After
waking, the gauge can proceed with the initialization of the battery information (OCV, profile selection, and so
forth).
16
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
8.5 Programming
8.5.1 Standard Data Commands
The fuel gauge uses a series of 2-byte standard commands to enable system reading and writing of battery
information. Each standard command has an associated command-code pair, as indicated in Table 1. Because
each command consists of two bytes of data, two consecutive I2C transmissions must be executed both to
initiate the command function and to read or write the corresponding two bytes of data. Additional options for
transferring data are described in Extended Data Commands. Read and write permissions depend on the active
access mode, SEALED or UNSEALED. For details, see bq27520-G4 Technical Reference Manual, SLUUA35.
See Communications for I2C details.
Table 1. Standard Commands
COMMAND CODE
UNIT
SEALED
ACCESS
CNTL
0x00 and 0x01
NA
RW
RW
NAME
Control( )
AtRate( )
AR
0x02 and 0x03
mA
AtRateTimeToEmpty( )
ARTTE
0x04 and 0x05
Minutes
R
Temperature( )
TEMP
0x06 and 0x07
0.1°K
RW
Voltage( )
VOLT
0x08 and 0x09
mV
R
FLAGS
0x0A and 0x0B
NA
R
NominalAvailableCapacity( )
NAC
0x0C and 0x0D
mAh
R
FullAvailableCapacity( )
FAC
0x0E and 0x0F
mAh
R
RemainingCapacity( )
RM
0x10 and 0x11
mAh
R
FullChargeCapacity( )
FCC
0x12 and 0x13
mAh
R
AI
0x14 and 0x15
mA
R
TTE
0x16 and 0x17
Minutes
R
SI
0x18 and 0x19
mA
R
StandbyTimeToEmpty( )
STTE
0x1A and 0x1B
Minutes
R
StateOfHealth( )
SOH
0x1C and 0x1D
% / num
R
CC
0x1E and 0x1F
num
R
SOC
0x20 and 0x21
%
R
0x22 and 0x23
mA
R
0x28 and 0x29
0.1°K
R
Flags( )
AverageCurrent( )
TimeToEmpty( )
StandbyCurrent( )
CycleCount( )
StateOfCharge( )
InstantaneousCurrent( )
InternalTemperature( )
INTTEMP
ResistanceScale( )
OperationConfiguration( )
0x2A and 0x2B
R
Op Config
0x2C and 0x2D
NA
R
0x2E and 0x2F
mAh
R
UFRM
0x6C and 0x6D
mAh
R
FRM
0x6E and 0x6F
mAh
R
UFFCC
0x70 and 0x71
mAh
R
FFCC
0x72 and 0x73
mAh
R
UFSOC
0x74 and 0x75
%
R
DesignCapacity( )
UnfilteredRM( )
FilteredRM( )
UnfilteredFCC( )
FilteredFCC( )
TrueSOC( )
8.5.2 Extended Data Commands
Extended commands offer additional functionality beyond the standard set of commands. They are used in the
same manner; however, unlike standard commands, extended commands are not limited to 2-byte words. The
number of command bytes for a given extended command range in size from single to multiple bytes is specified
in Table 2. See bq27520-G4 Technical Reference Manual, SLUUA35 for details on accessing the data flash.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
17
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
Table 2. Extended Data Commands
NAME
Reserved
COMMAND
CODE
UNIT
SEALED
ACCESS (1) (2)
UNSEALED
ACCESS (1) (2)
R
R
0x34 to 0x3D
NA
DataFlashClass( )
(2)
0x3E
NA
NA
RW
DataFlashBlock( )
(2)
0x3F
NA
RW
RW
0x40 to 0x5F
NA
R
RW
BlockDataCheckSum( )
0x60
NA
RW
RW
BlockDataControl( )
0x61
NA
NA
RW
ApplicationStatus( )
0x6A
NA
R
R
0x6B to 0x7F
NA
R
R
BlockData( )
Reserved
(1)
(2)
SEALED and UNSEALED states are entered via commands to Control( ) 0x00 and 0x01.
In sealed mode, data flash cannot be accessed through commands 0x3E and 0x3F.
8.5.3 Communications
8.5.3.1 I2C Interface
The bq27520-G4 fuel gauge supports the standard I2C read, incremental read, quick read, one byte write, and
incremental write functions. The 7-bit device address (ADDR) is the most significant 7 bits of the hex address
and is fixed as 1010101. The first 8-bits of the I2C protocol is, therefore, 0xAA or 0xAB for write or read,
respectively.
Host generated
S
ADDR[6:0]
0 A
Gauge generated
CMD [7:0]
A
DATA [7:0]
A P
S
ADDR[6:0]
(a) 1-byte write
S
ADDR[6:0]
0 A
1 A
DATA [7:0]
N P
(b) quick read
CMD [7:0]
A Sr
ADDR[6:0]
1 A
DATA [7:0]
N P
(c) 1- byte read
S
ADDR[6:0]
0 A
CMD [7:0]
A Sr
ADDR[6:0]
1 A
DATA [7:0]
A ...
DATA [7:0]
N P
(d) incremental read
S
ADDR[6:0]
0 A
CMD[7:0]
A
DATA [7:0]
A
DATA [7:0]
A
...
A P
(e) incremental write
(S = Start , Sr = Repeated Start , A = Acknowledge , N = No Acknowledge , and P = Stop).
Figure 8. I2C Read, Incremental Read, Quick Read, One Byte Write, and Incremental Write Functions
The “quick read” returns data at the address indicated by the address pointer. The address pointer, a register
internal to the I2C communication engine, increments whenever data is acknowledged by the fuel gauge or the
I2C master. “Quick writes” function in the same manner and are a convenient means of sending multiple bytes to
consecutive command locations (such as two-byte commands that require two bytes of data).
The following command sequences are not supported:
Attempt to write a read-only address (NACK after data sent by master):
Figure 9. Invalid Write
18
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
Attempt to read an address above 0x6B (NACK command):
Figure 10. Invalid Read
8.5.3.2 I2C Time Out
The I2C engine releases both SDA and SCL if the I2C bus is held low for 2 seconds. If the fuel gauge was
holding the lines, releasing them frees them for the master to drive the lines. If an external condition is holding
either of the lines low, the I2C engine enters the low-power sleep mode.
8.5.3.3 I2C Command Waiting Time
To ensure proper operation at 400 kHz, a t(BUF) ≥ 66 μs bus free waiting time must be inserted between all
packets addressed to the fuel gauge. In addition, if the SCL clock frequency (fSCL) is > 100 kHz, use individual 1byte write commands for proper data flow control. The following diagram shows the standard waiting time
required between issuing the control subcommand the reading the status result. An OCV_CMD subcommand
requires 1.2 seconds prior to reading the result. For read-write standard command, a minimum of 2 seconds is
required to get the result updated. For read-only standard commands, there is no waiting time required, but the
host should not issue all standard commands more than two times per second. Otherwise, the fuel gauge could
result in a reset issue due to the expiration of the watchdog timer.
S
ADDR [6:0]
0 A
CMD [7:0]
A
DATA [7:0]
A P
66ms
S
ADDR [6:0]
0 A
CMD [7:0]
A
DATA [7:0]
A P
66ms
S
ADDR [6:0]
0 A
CMD [7:0]
A Sr
ADDR [6:0]
1 A
DATA [7:0]
A
DATA [7:0]
N P
66ms
N P
66ms
Waiting time inserted between two 1-byte write packets for a subcommand and reading results
(required for 100 kHz < fSCL £ 400 kHz)
S
ADDR [6:0]
0 A
CMD [7:0]
A
DATA [7:0]
S
ADDR [6:0]
0 A
CMD [7:0]
A Sr
ADDR [6:0]
A
1 A
DATA [7:0]
DATA [7:0]
A P
A
66ms
DATA [7:0]
Waiting time inserted between incremental 2-byte write packet for a subcommand and reading results
(acceptable for fSCL £ 100 kHz)
S
ADDR [6:0]
DATA [7:0]
0 A
A
CMD [7:0]
DATA [7:0]
A Sr
N P
ADDR [6:0]
1 A
DATA [7:0]
A
DATA [7:0]
A
66ms
Waiting time inserted after incremental read
Figure 11. Standard I2C Command Waiting Time Required
8.5.3.4 I2C Clock Stretching
A clock stretch can occur during all modes of fuel gauge operation. In SLEEP and HIBERNATE modes, a short
clock stretch occurs on all I2C traffic as the device must wake-up to process the packet. In the other modes (BAT
INSERT CHECK, NORMAL, SNOOZE) clock stretching only occurs for packets addressed for the fuel gauge.
The majority of clock stretch periods are small as the I2C interface performs normal data flow control. However,
less frequent yet more significant clock stretch periods may occur as blocks of Data Flash are updated. The
following table summarizes the approximate clock stretch duration for various fuel gauge operating conditions.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
19
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
Table 3. Approximate Clock Stretch Duration
GAUGING
MODE
APPROXIMATE
DURATION
OPERATING CONDITION or COMMENT
SLEEP
HIBERNATE
Clock stretch occurs at the beginning of all traffic as the device wakes up.
BAT INSERT
CHECK,
NORMAL,
SNOOZE
Clock stretch occurs within the packet for flow control (after a start bit, ACK or first data bit).
100 µs
Normal Ra table Data Flash updates.
24 ms
20
5 ms
Data Flash block writes.
72 ms
Restored Data Flash block write after loss of power.
116 ms
End of discharge Ra table Data Flash update.
144 ms
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The bq27520-G4 system-side Li-Ion battery fuel gauge is a microcontroller peripheral that provides fuel gauging
for single-cell Li-Ion battery packs. The device requires little system microcontroller firmware development. The
fuel resides on the main board of the system and manages an embedded battery (non-removable) or a up to
14500-mAhr Capacity removable battery pack. To allow for optimal performance in the end application, special
considerations must be taken to ensure minimization of measurement error through proper printed circuit board
(PCB) board layout. Such requirements are detailed in Design Requirements.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
21
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
9.2 Typical Application
U1
BQ27520
Figure 12. bq27520-G4 System-Side Li-Ion Battery Fuel Gauge Typical Application Schematic
22
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
9.2.1 Design Requirements
Several key parameters must be updated to align with a given application's battery characteristics. For highest
accuracy gauging, it is important to follow-up this initial configuration with a learning cycle to optimize resistance
and maximum chemical capacity (Qmax) values prior to sealing and shipping systems to the field. Successful
and accurate configuration of the fuel gauge for a target application can be used as the basis for creating a
"golden" gas gauge (.fs) file that can be written to all gauges, assuming identical pack design and Li-ion cell
origin (chemistry, lot, and so on). Calibration data is included as part of this golden GG file to cut down on
system production time. If going this route, it is recommended to average the voltage and current measurement
calibration data from a large sample size and use these in the golden file. Table 4, Key Data Flash Parameters
for Configuration, shows the items that should be configured to achieve reliable protection and accurate gauging
with minimal initial configuration.
Table 4. Key Data Flash Parameters for Configuration
NAME
DEFAULT
UNIT
RECOMMENDED SETTING
Design Capacity
1000
mAh
Set based on the nominal pack capacity as interpreted from cell manufacturer's
datasheet. If multiple parallel cells are used, should be set to N × Cell Capacity.
Design Energy Scale
1
-
Reserve Capacity-mAh
0
mAh
Set to desired runtime remaining (in seconds / 3600) × typical applied load
between reporting 0% SOC and reaching Terminate Voltage, if needed.
Should be configured using TI-supplied Battery Management Studio software.
Default open-circuit voltage and resistance tables are also updated in
conjunction with this step. Do not attempt to manually update reported Device
Chemistry as this does not change all chemistry information! Always update
chemistry using the appropriate software tool (that is, bqStudio).
Set to 10 to convert all power values to cWh or to 1 for mWh. Design Energy
is divided by this value.
Chem ID
0100
hex
Load Mode
1
-
Set to applicable load model, 0 for constant current or 1 for constant power.
Load Select
1
-
Set to load profile which most closely matches typical system load.
Qmax Cell 0
1000
mAh
Set to initial configured value for Design Capacity. The gauge will update this
parameter automatically after the optimization cycle and for every regular
Qmax update thereafter.
Cell0 V at Chg Term
4200
mV
Set to nominal cell voltage for a fully charged cell. The gauge will update this
parameter automatically each time full charge termination is detected.
Terminate Voltage
3200
mV
Set to empty point reference of battery based on system needs. Typical is
between 3000 and 3200 mV.
Ra Max Delta
44
mΩ
Set to 15% of Cell0 R_a 4 resistance after an optimization cycle is completed.
Charging Voltage
4200
mV
Set based on nominal charge voltage for the battery in normal conditions
(25°C, etc). Used as the reference point for offsetting by Taper Voltage for full
charge termination detection.
Taper Current
100
mA
Set to the nominal taper current of the charger + taper current tolerance to
ensure that the gauge will reliably detect charge termination.
Taper Voltage
100
mV
Sets the voltage window for qualifying full charge termination. Can be set
tighter to avoid or wider to ensure possibility of reporting 100% SOC in outer
JEITA temperature ranges that use derated charging voltage.
Dsg Current Threshold
60
mA
Sets threshold for gauge detecting battery discharge. Should be set lower than
minimal system load expected in the application and higher than Quit Current.
Chg Current Threshold
75
mA
Sets the threshold for detecting battery charge. Can be set higher or lower
depending on typical trickle charge current used. Also should be set higher
than Quit Current.
Quit Current
40
mA
Sets threshold for gauge detecting battery relaxation. Can be set higher or
lower depending on typical standby current and exhibited in the end system.
Avg I Last Run
–299
mA
Current profile used in capacity simulations at onset of discharge or at all times
if Load Select = 0. Should be set to nominal system load. Is automatically
updated by the gauge every cycle.
Avg P Last Run
–1131
mW
Power profile used in capacity simulations at onset of discharge or at all times
if Load Select = 0. Should be set to nominal system power. Is automatically
updated by the gauge every cycle.
Sleep Current
15
mA
Sets the threshold at which the fuel gauge enters SLEEP mode. Take care in
setting above typical standby currents else entry to SLEEP may be
unintentionally blocked.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
23
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
Table 4. Key Data Flash Parameters for Configuration (continued)
NAME
DEFAULT
UNIT
RECOMMENDED SETTING
CC Gain
10
mΩ
Calibrate this parameter using TI-supplied bqStudio software and calibration
procedure in the TRM. Determines conversion of coulomb counter measured
sense resistor voltage to current.
CC Delta
10
mΩ
Calibrate this parameter using TI-supplied bqStudio software and calibration
procedure in the TRM. Determines conversion of coulomb counter measured
sense resistor voltage to passed charge.
CC Offset
–1418
Counts
Calibrate this parameter using TI-supplied bqStudio software and calibration
procedure in the TRM. Determines native offset of coulomb counter hardware
that should be removed from conversions.
Board Offset
0
Counts
Calibrate this parameter using TI-supplied bqStudio software and calibration
procedure in the TRM. Determines native offset of the printed circuit board
parasitics that should be removed from conversions.
Pack V Offset
0
mV
Calibrate this parameter using TI-supplied bqStudio software and calibration
procedure in the TRM. Determines voltage offset between cell tab and ADC
input node to incorporate back into or remove from measurement, depending
on polarity.
9.2.2 Detailed Design Procedure
9.2.2.1 BAT Voltage Sense Input
A ceramic capacitor at the input to the BAT pin is used to bypass AC voltage ripple to ground, greatly reducing
its influence on battery voltage measurements. It proves most effective in applications with load profiles that
exhibit high-frequency current pulses (that is, cell phones) but is recommended for use in all applications to
reduce noise on this sensitive high-impedance measurement node.
9.2.2.2 SRP and SRN Current Sense Inputs
The filter network at the input to the coulomb counter is intended to improve differential mode rejection of voltage
measured across the sense resistor. These components should be placed as close as possible to the coulomb
counter inputs and the routing of the differential traces length-matched to best minimize impedance mismatchinduced measurement errors.
9.2.2.3 Sense Resistor Selection
Any variation encountered in the resistance present between the SRP and SRN pins of the fuel gauge will affect
the resulting differential voltage, and derived current, it senses. As such, it is recommended to select a sense
resistor with minimal tolerance and temperature coefficient of resistance (TCR) characteristics. The standard
recommendation based on best compromise between performance and price is a 1% tolerance, 100 ppm drift
sense resistor with a 1-W power rating.
9.2.2.4 TS Temperature Sense Input
Similar to the BAT pin, a ceramic decoupling capacitor for the TS pin is used to bypass AC voltage ripple away
from the high-impedance ADC input, minimizing measurement error. Another helpful advantage is that the
capacitor provides additional ESD protection since the TS input to system may be accessible in systems that use
removable battery packs. It should be placed as close as possible to the respective input pin for optimal filtering
performance.
9.2.2.5 Thermistor Selection
The fuel gauge temperature sensing circuitry is designed to work with a negative temperature coefficient-type
(NTC) thermistor with a characteristic 10-kΩ resistance at room temperature (25°C). The default curve-fitting
coefficients configured in the fuel gauge specifically assume a 103AT-2 type thermistor profile and so that is the
default recommendation for thermistor selection purposes. Moving to a separate thermistor resistance profile (for
example, JT-2 or others) requires an update to the default thermistor coefficients in data flash to ensure highest
accuracy temperature measurement performance.
24
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
9.2.2.6 REGIN Power Supply Input Filtering
A ceramic capacitor is placed at the input to the fuel gauge internal LDO to increase power supply rejection
(PSR) and improve effective line regulation. It ensures that voltage ripple is rejected to ground instead of
coupling into the internal supply rails of the fuel gauge.
9.2.2.7 VCC LDO Output Filtering
A ceramic capacitor is also needed at the output of the internal LDO to provide a current reservoir for fuel gauge
load peaks during high peripheral utilization. It acts to stabilize the regulator output and reduce core voltage
ripple inside of the fuel gauge.
9.2.3 Application Curves
8.8
VREGIN = 2.7 V
VREGIN = 4.5 V
2.6
fOSC - High Frequency Oscillator (MHz)
VREG25 - Regulator Output Voltage (V)
2.65
2.55
2.5
2.45
2.4
2.35
8.7
8.6
8.5
8.4
8.3
8.2
8.1
8
-40
Temperature (qC)
-20
0
20
40
Temperature (qC)
D001
34
5
33.5
4
33
32.5
32
31.5
31
30.5
30
-40
-20
0
20
40
Temperature (qC)
60
80
100
100
D002
3
2
1
0
-1
-2
-3
-4
-5
-30
-20
D003
Figure 15. Low-Frequency Oscillator Frequency vs.
Temperature
80
Figure 14. High-Frequency Oscillator Frequency vs.
Temperature
Reported Temperature Error (qC)
fLOSC - Low Frequency Oscillator (kHz)
Figure 13. Regulator Output Voltage vs. Temperature
60
-10
0
10
20
30
Temperature (qC)
40
50
60
D004
Figure 16. Reported Internal Temperature Measurement
vs. Temperature
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
25
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
10 Power Supply Recommendations
10.1 Power Supply Decoupling
Both the REGIN input pin and the VCC output pin require low equivalent series resistance (ESR) ceramic
capacitors placed as closely as possible to the respective pins to optimize ripple rejection and provide a stable
and dependable power rail that is resilient to line transients. A 0.1-µF capacitor at the REGIN and a 1-µF
capacitor at VCC will suffice for satisfactory device performance.
11 Layout
11.1 Layout Guidelines
11.1.1 Sense Resistor Connections
Kelvin connections at the sense resistor are just as critical as those for the battery terminals themselves. The
differential traces should be connected at the inside of the sense resistor pads and not anywhere along the highcurrent trace path to prevent false increases to measured current that could result when measuring between the
sum of the sense resistor and trace resistance between the tap points. In addition, the routing of these leads
from the sense resistor to the input filter network and finally into the SRP and SRN pins needs to be as closely
matched in length as possible else additional measurement offset could occur. It is further recommended to add
copper trace or pour-based "guard rings" around the perimeter of the filter network and coulomb counter inputs to
shield these sensitive pins from radiated EMI into the sense nodes. This prevents differential voltage shifts that
could be interpreted as real current change to the fuel gauge. All of the filter components need to be placed as
close as possible to the coulomb counter input pins.
11.1.2 Thermistor Connections
The thermistor sense input should include a ceramic bypass capacitor placed as close to the TS input pin as
possible. The capacitor helps to filter measurements of any stray transients as the voltage bias circuit pulses
periodically during temperature sensing windows.
11.1.3 High-Current and Low-Current Path Separation
For best possible noise performance, it is extremely important to separate the low-current and high-current loops
to different areas of the board layout. The fuel gauge and all support components should be situated on one side
of the boards and tap off of the high-current loop (for measurement purposes) at the sense resistor. Routing the
low-current ground around instead of under high-current traces will further help to improve noise rejection.
26
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
bq27520-G4
www.ti.com
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
11.2 Layout Example
Battery power
connection to
system
Use copper
pours for battery
power path to
minimize IR
losses
SCL
To system host
processor
SDA
BAT_LOW
BATTERY PACK
CONNECTOR
BAT_GD
C1
PACK+
Kelvin connect the
BAT sense line right
at positive terminal to
battery pack
C2
BI/TOUT
BAT
REGIN
C3
THERM
CE
VCC
VSS
VSS
SDA
BAT_GD
SRN
SCL
SOC_INT
SRP
TS
BAT_LOW
SOC_INT
PACK –
10 mΩ 1%
Via connects to Power Ground
Ground return to
system
Kelvin connect SRP
and SRN
connections right at
Rsense terminals
Figure 17. Layout Recommendation
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
27
bq27520-G4
SLUSB20B – NOVEMBER 2012 – REVISED DECEMBER 2015
www.ti.com
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
To obtain a copy of any of the following TI documents, call the Texas Instruments Literature Response Center at
(800) 477-8924 or the Product Information Center (PIC) at (972) 644-5580. When ordering, identify this
document by its title and literature number. Updated documents also can be obtained through the TI Web site at
www.ti.com.
• bq27520-G4 Technical Reference Manual, SLUUA35
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
Impedance Track, NanoFree, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
28
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: bq27520-G4
PACKAGE OPTION ADDENDUM
www.ti.com
9-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
BQ27520YZFR-G4
ACTIVE
DSBGA
YZF
15
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ27520
BQ27520YZFT-G4
ACTIVE
DSBGA
YZF
15
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ27520
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
9-Sep-2014
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
BQ27520YZFR-G4
DSBGA
YZF
15
3000
180.0
8.4
BQ27520YZFR-G4
DSBGA
YZF
15
3000
178.0
BQ27520YZFT-G4
DSBGA
YZF
15
250
180.0
BQ27520YZFT-G4
DSBGA
YZF
15
250
178.0
2.1
2.76
0.81
4.0
8.0
Q1
9.2
2.1
2.76
0.81
4.0
8.0
Q1
8.4
2.1
2.76
0.81
4.0
8.0
Q1
9.2
2.1
2.76
0.81
4.0
8.0
Q1
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
BQ27520YZFR-G4
DSBGA
YZF
15
3000
182.0
182.0
20.0
BQ27520YZFR-G4
DSBGA
YZF
15
3000
270.0
225.0
227.0
BQ27520YZFT-G4
DSBGA
YZF
15
250
182.0
182.0
20.0
BQ27520YZFT-G4
DSBGA
YZF
15
250
270.0
225.0
227.0
Pack Materials-Page 2
Height (mm)
D: Max = 2.64 mm, Min = 2.58 mm
E: Max = 1.986 mm, Min =1.926 mm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated