C32xx 5x7mm SMD HCMOS Clock Oscillator 5.0 Volts Model C32xx is a 1.544MHz to 106.250MHz HCMOS Clock Oscillator operating at 5.0Volts. The oscillator utilizes Fundamental or High Q Third Overtone crystal design providing very low Jitter and Phase Noise. No Sub-Harmonics are present in the Output Signal. 5x7mm SMD Applications: Digital Video SONET/SDH/DWDM Storage Area Networks Broadband Access Ethernet, Gigabit Ethernet Rev.: F Date: 03-06-08 C32xx 5x7mm SMD HCMOS Clock Oscillator 5.0 Volts Frequency Range: 1.544 to 106.250Mhz Temperature Range: (standard) (Option M) (Option E) 0°C to +70°C -20°C to +70°C -40°C to +85°C Storage: Input Voltage: Input Current: -55°C to 120°C 5.0V ± 0.5V 60mA Max Output: Symmetry: (Option) Rise/Fall Time: HCMOS/TTL 40/60% Max @ 50%Vdd 45/55% Max @ 50% Vdd 6nsec Max @ 20% to 80% Vdd Logic: Disable Time Start-up Time Load: Jitter RMS: 12KHz~20MHz “0”= 10% Vdd Max “1”= 90% Vdd Min. 200nSec Max 1mSec Typ., 2mSec Max 50pF/10TTL Max Sub-harmonics: None Frequency Stability Options(ppm): Aging: ±10, ±20, ±25, ±50, ±100 0.5psec Typ., 1psec Max <3ppm 1st/yr, <1ppm every year thereafter PART NUMBER GUIDE Symmetry Part Number Example:C3292-44.736MHz Intermediate Temp: CM3292-44.736MHz Extended Temp: CE3292-44.736MHz C = 0°C to 70°C Symmetry 40/60% *CM = -20°C to 70°C Part Number *CE = -40°C to 85°C Stability C*3290 ±100ppm C*3292 ±50ppm C*3291 ±25ppm C*3298 ±20ppm C3297 ±10ppm 45/55% Stability C*3990 ±100ppm C*3992 ±50ppm C*3991 ±25ppm C*3998 ±20ppm C3997 ±10ppm Rev.: F Date: 03-06-08 C32xx 5x7mm SMD HCMOS Clock Oscillator 5.0 Volts OUT mA M pin 3 pin 4 Vdd PWR Supply Bypass Cap. VM O/P Load incl Probe Cl OUT OSC. GND pin 2 pin 1 High Impedance GND or "LOW" Shock: Solderability: Vibration: Solvent Resistance: Resistance to Soldering Heat: MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2003 MIL-STD-883, Method 2007, Condition A MIL-STD-202, Method 215 MIL-STD-202, Method 210, Condition I or J RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. 260°C 217°C 200°C 150°C Environmental: Preheat 180 Secs. Max. 8 Minutes Max. Thermal Shock: MIL-STD-883, Method 1011, Condition A Moisture Resistance: MIL-STD-883, Method 1004 NOTE: Reflow Profile with 240°C peak also acceptable. 0.075 (1.80) 0.204 (5.02) Denotes pad 1 XXX=Date Code XX=Lot Code 0.055 Typ. (1.40 Typ.) #2 #4 #3 0.200 ±0.005 (5.08 ±0.13) 0.045 ±0.008 (1.14 ±0.20) Tri-State Function Pin #1 State SUGGESTED PAD LAYOUT Active “0”level 0.3*Vcc Max High Z Pad 1 0.165 (4.19) Output State Open or N/C “1” level 0.7*Vcc Min 0.071 SQ (1.80) #1 90 Secs. Max. 260°C for 10 Secs. Max. 0.283 (7.20) P/N XXX Frequency XX Critical Temperature Zone Ramp-Down 6°C/Sec. TEMPERATURE Mechanical: Oscillation OPEN or "HIGH" Active Connection Enable/Disable 2 GND 3 Out 4 Vcc 0.200 (5.08) 0.01uF Bypass Capacitor Recommended Rev.: F Date: 03-06-08