DG200B Vishay Siliconix Monolithic Dual SPST CMOS Analog Switch DESCRIPTION FEATURES The DG200B is a dual, single-pole, single-throw analog switch designed to provide general purpose switching of analog signals. This device is ideally suited for designs requiring a wide analog voltage range coupled with low on-resistance. • • • • The DG200B is designed on Vishay Siliconix’ improved PLUS-40 CMOS process. An epitaxial layer prevents latchup. BENEFITS Each switch conducts equally well in both directions when on, and blocks up to 30 V peak-to-peak when off. In the on condition, this bi-directional switch introduces no offset voltage of its own. ± 15 V Input Signal Range 44 V Maximum Supply Ranges On-Resistance: 45 Ω TTL and CMOS Compatibility Pb-free Available RoHS* COMPLIANT • Wide Dynamic Range • Simple Interfacing • Reduced External Component Count APPLICATIONS • • • • Servo Control Switching Programmable Gain Amplifiers Audio Switching Programmable Filters FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION Plastic Dip TRUTH TABLE IN1 Logic 13 NC 0 ON 1 OFF IN2 1 14 NC 2 GND 3 12 V+ Substrate NC 4 11 NC S2 5 10 S1 D2 6 9 D1 V– 7 8 NC Switch Logic "0" ≤ 0.8 V Logic "1" ≥ 2.4 V Top View ORDERING INFORMATION Temp Range Package Part Number - 40 to 85 °C 14-Pin Plastic DIP DG200BDJ DG200BDJ-E3 * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 71357 S-71155–Rev. C, 11-Jun-07 www.vishay.com 1 DG200B Vishay Siliconix ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted Parameter Limit V+ to VGND to VDigital Inputs Unit 44 a, 25 (V-) - 2 V to (V+) + 2 V or 30 mA, whichever occurs first 30 VS, VD Current (Any Terminal) Continuous Current S or D (Pulsed at 1 ms, 10 % Duty Cycle Max) Storage Temperature V mA 100 - 65 to 150 °C 470 mW 14-Pin Plastic DIPc Power Dissipation (Package)b Notes: a. Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to PC Board. c. Derate 6.5 mW/°C above 25 °C. SCHEMATIC DIAGRAM (TYPICAL CHANNEL) V+ SX VL V- Level Shift/ Drive V+ INX DX GND V- Figure 1. www.vishay.com 2 Document Number: 71357 S-71155–Rev. C, 11-Jun-07 DG200B Vishay Siliconix SPECIFICATIONSa Analog Signal Rangee VANALOG VD = ± 10 V, IS = - 1 mA Drain-Source On-Resistance rDS(on) Source Off Leakage Current IS(off) VS = ± 14 V, VD = Drain Off Leakage Current ID(off) VD = ± 14 V, VS = Channel On Leakage Currentf ID(on) 14 V ± Symbol ± Parameter Analog Switch Test Conditions Unless Otherwise Specified V+ = 15 V, V- = - 15 V VIN = 2.4 V, 0.8 Vf 14 V VS = VD = ± 14 V Limits - 40 to 85 °C Tempb Minc Full - 15 Room Full Room Full Room Full Room Full -2 - 100 -2 - 100 -2 - 200 Typd Maxc Unit 15 V 45 85 100 2 100 2 100 2 200 Ω ± 0.01 ± 0.01 ± 0.1 nA Digital Control Input Current with Input Voltage High Input Current with Input Voltage Low Dynamic Characteristics VIN = 15 V IINL Turn-On Time tON Turn-Off Time tOFF Charge Injection Room Full Room Full Room Full VIN = 2.4 V IINH VIN = 0 V See Switching Time Test Circuit CL = 1000 pF, Rg = 0 Ω, Vg = 0 V - 0.5 -1 0.0009 0.005 - 0.5 -1 Room 300 1000 Room 200 425 Room 1 Source Off Capacitance Drain Off Capacitance CD(off) Channel-On Capacitance CD(on)+ CS(on) VS = VD = 0 V, VIN = 0 V Room 16 OIRR XTALK VIN = 5 V, RL = 75 Ω VS = 2 V, f = 1 MHz Room 90 Room 95 Positive Supply Current I+ Negative Supply Current I- Both Channels On or Off VIN = 0 V and 5.0 V Off Isolation Crosstalk (Channel-to-Channel) µA - 0.0015 Q CS(off) f = 140 kHz VIN = 5 V 0.5 1 VS = 0 V Room 5 VD = 0 V Room 5 ns pC pF dB Power Supplies Room Room 50 - 10 µA Notes: a. Refer to PROCESS OPTION FLOWCHART. b. Room = 25 °C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. VIN = input voltage to perform proper function. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Document Number: 71357 S-71155–Rev. C, 11-Jun-07 www.vishay.com 3 DG200B Vishay Siliconix r DS(on) - Drain-Source On-Resistance (Ω) TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted 110 100 100 90 90 V+ = 15 V V- = - 15 V 80 ±5V 80 70 70 60 ± 10 V 60 50 40 r DS(on) - ± 20 V 20 -8 -4 0 4 8 12 16 40 25 °C 30 - 55 °C 20 10 0 - 15 10 - 20 - 16 - 12 85 °C 50 ± 15 V 30 125 °C 20 - 10 -5 0 10 15 rDS(on) vs. VD and Temperature rDS(on) vs. VD and Power Supply Voltages 40 1 nA V+ = 15 V V- = - 15 V VS, V D = ± 14 V V+ = 22 V V- = - 22 V TA = 25 °C 30 I S, I D - Current (pA) 20 I S, I D - Current 5 VD - Drain Voltage (V) VD - Drain Voltage (V) 100 pA IS(off), ID(off) 10 pA ID(on) 10 IS(off), ID(off) 0 - 10 - 20 - 30 1 pA - 55 - 35 - 15 5 25 45 65 85 - 40 - 20 105 125 - 15 - 10 -5 0 5 10 15 20 Temperature (°C) Leakage Currents vs. Analog Voltage Leakage Current vs. Temperature TEST CIRCUITS VO is the steady state output with switch on. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. + 15 V Logic Input Switch Input 3V tr < 20 ns tf < 20 ns 50 % 0V VS = + 5 V tOFF VS D VO IN 3V 90 % Switch Output V+ S GND V- CL 35 pF RL 1 kΩ VO tON - 15 V VO = V S RL RL + rDS(on) Figure 2. Switching Time www.vishay.com 4 Document Number: 71357 S-71155–Rev. C, 11-Jun-07 DG200B Vishay Siliconix TEST CIRCUITS + 15 V ΔVO Rg VO V+ S D VO CL 1000 pF IN Vg 3V INX ON OFF ON V- GND ΔVO = measured voltage error due to charge injection The charge injection in coulombs is ΔQ = C L x ΔVO - 15 V Figure 3. Charge Injection + 15 V C V+ S VS VO D Rg = 50 Ω RL IN 5V GND V- C - 15 V VS Off Isolation = 20 log VO Figure 4. Off Isolation + 15 V C V+ S1 VS Rg = 50 Ω D1 50 Ω IN1 0V NC 0V S2 VO D2 RL IN2 GND V- C - 15 V XTALK = 20 log VS VO C = RF bypass Figure 5. Channel-to-Channel Crosstalk Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http://www.vishay.com/ppg?71357. Document Number: 71357 S-71155–Rev. C, 11-Jun-07 www.vishay.com 5 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1