60W Single Output Class 2 Switching Power Supply ELN-60 series Features : Universal AC input / Full range Built-in constant current limiting circuit with adjustable OCP level Protections: Short circuit / Overload / Over voltage Fully isolated plastic case with IP64 level IP64 design for indoor or outdoor installations Optional dimming function : 1~10VDC(D type) or PWM controlled(P type) UL1310 Class 2 power unit Cooling by free air convection 100% full load burn-in test Low cost, high reliability Suitable for LED lighting and moving sign applications 2 years warranty SPECIFICATION MODEL DC VOLTAGE ELN-60-9 ELN-60-12 ELN-60-15 ELN-60-24 ELN-60-27 ELN-60-48 9V 12V 15V 24V 27V 48V LED OPERATION VOLTAGE Note.8 3 ~ 9V 5A RATED CURRENT 3 ~ 12V 3 ~ 15V 3 ~ 24V 3 ~ 27V 3 ~ 48V 5A 4A 2.5A 2.3A 1.3A CURRENT RANGE 0 ~ 5A 0 ~ 5A 0 ~ 4A 0 ~ 2.5A 0 ~ 2.3A 0 ~ 1.3A RATED POWER 45W 60W 60W 60W 62.1W 62.5W 120mVp-p 150mVp-p 150mVp-p 200mVp-p 250mVp-p 10.8 ~ 13.2V 13.5 ~ 16.5V 21.6 ~ 26.4V 24.3 ~ 29.7V 43.2 ~ 52.8V 87% 87% 88% RIPPLE & NOISE (max.) Note.2 120mVp-p OUTPUT IP64 VOLTAGE ADJ. RANGE Note.7 8.7 ~ 10.5V Can be adjusted by internal potential meter SVR1 CURRENT ADJ. RANGE Note.7 -25% ~ 3%. Can be adjusted by internal potential meter SVR2 VOLTAGE TOLERANCE Note.3 5.0% LINE REGULATION 1.0% 2.0% LOAD REGULATION SETUP, RISE TIME Note.6 500ms, 30ms / 230VAC 50ms/230VAC HOLD UP TIME (Typ.) VOLTAGE RANGE Note.5 90 ~ 264VAC FREQUENCY RANGE INPUT 1500ms, 30ms / 115VAC at full load 16ms/115VAC at full load 47 ~ 63Hz EFFICIENCY (Typ.) 82% AC CURRENT (Typ.) INRUSH CURRENT(max.) 1.2A/115VAC 0.7A/230VAC COLD STAR 60A/230VAC LEAKAGE CURRENT OVER CURRENT PROTECTION OVER VOLTAGE 85% 86% 0.25mA / 240VAC 130% max. 95 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed 11 ~ 13.5V 13.8 ~ 16V 17.5 ~ 21V 28 ~ 32V 31 ~ 35V 54 ~ 60V Protection type : Shut down o/p voltage, re-power on to recover FUNCTION DIMMING CONTROL (OPTIONAL) 1 ~ 10VDC or PWM signal : 100Hz ~ 3KHz WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION -20 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +80 0.03%/ , 10 ~ 95% RH (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS Design refer to UL1310 Class 2,TUV EN60950-1, CAN/CSA C22.2 No. 223-M91(except for 48V), EN61347-2-13; IP64 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH EMC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B OTHERS HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY MTBF Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A 603Khrs min. MIL-HDBK-217F (25 ) 181*61.5*35mm (L*W*H) 0.4Kg; 24pcs/11Kg/0.75CUFT DIMENSION PACKING NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the derating curve for more details. 5. The power supply is considered a component which will be installed a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. Output voltage can be adjusted through the SVR1 on the PCB ; limit of output constant current level can be adjusted through the SVR2 on the PCB. 8. Constant current operation region is within the specified output voltage range above. This is the suitable operation region for LED related applications. File Name:ELN-60-SPEC 2008-06-16 ELN-60 60W Single Output Class 2 Switching Power Supply Mechanical Specification Case No.960A series Unit:mm 181 21.25 6.26 300 2-R2.5 +V(Red) -V(Black) 61.5 300 21.25 AC/L(Brown) AC/N(Blue) 18AWG 2C 18AWG 2C 35 6.26 OUTPUT(with optional dimming function) +V(Red) -V(Black) DIM+(Blue) DIM-(White) Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2 shown in the diagram. SVR1 SVR2 SVR1 Output voltage adjustment SVR2 Output current adjustment fosc : 60KHz Block Diagram POWER SWITCHING EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER +V -V DIM- O.L.P. DETECTION CIRCUIT PWM CONTROL 10V PWM or 1~10V O.C.P. O.V.P. DIM+ Derating Curve Optional Dimming Control Static Characteristics Ta=25 100 100 90 80 80 70 50 LOAD (%) LOAD (%) 60 40 20 -20 -15 -5 0 15 30 40 45 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 264 INPUT VOLTAGE (V) 60Hz File Name:ELN-60-SPEC 2008-06-16 ELN-60 60W Single Output Class 2 Switching Power Supply series Dimming Control (Optional) Level of output current can be adjusted through the dimming control function. (1)1~10V 95% DIM+ Output Current + Vdc DIMVdc: 1~10V 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 45% 5% 0% 0 1 2 3 4 5 6 7 8 9 10 DC Input (2)PWM V Output Current f: 100Hz ~ 3KHz f 10V t1 t2 Duty= t1 ,0 ~ 100% t1+t2 Lo:0V Hi:10V f 95% 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 60% 15% 0% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty Cycle 11% File Name:ELN-60-SPEC 2008-06-16 60W Single Output Class 2 Switching Power Supply ELN-60 series Recommend Application Deployment (24V) +V(Red) 24V, 2.5A ELN-60-24 -V(Black) +V(Red) 24V, 2.5A ELN-60-24 -V(Black) R R R R LED LED 1 to 6 LEDs // 4 strips This configuration is based on LED with the following parameters : V F = 3.0~3.5V I F = 600~700mA 6 LEDs // 1 to 4 strips This configuration is based on LED with the following parameters : V F = 3.0~3.5V I F =600~700mA R=10 ohm, 10W +V(Red) 24V, 2.5A -V(Black) +V(Red) ELN-60-24 24V, 2.5A -V(Black) ELN-60-24 R R R R R R R R LED LED 1 to 6 LEDs // 8 strips This configuration is based on LED with the following parameters : V F = 3.0~3.5V I F =3 00~350mA 6 LEDs // 1 to 8 strips This configuration is based on LED with the following parameters : V F = 3.0~3.5V I F =300~350mA R=20 ohm, 3W File Name:ELN-60-SPEC 2008-06-16