ATMEL ATF20V8B-15PI Highperformance ee pld Datasheet

Features
• Industry-standard Architecture
– Emulates Many 24-pin PALs®
– Low-cost Easy-to-use Software Tools
• High-speed Electrically-erasable Programmable Logic Devices
– 7.5 ns Maximum Pin-to-pin Delay
• Several Power Saving Options
Device
ICC, Standby
ICC, Active
ATF20V8B
50 mA
55 mA
ATF20V8BQ
35 mA
40 mA
ATF20V8BQL
5 mA
20 mA
Highperformance
EE PLD
• CMOS and TTL Compatible Inputs and Outputs
• Input and I/O Pull-up Resistors
• Advanced Flash Technology
– Reprogrammable
– 100% Tested
High-reliability CMOS Process
– 20 Year Data Retention
– 100 Erase/Write Cycles
– 2,000V ESD Protection
– 200 mA Latchup Immunity
Commercial and Industrial Temperature Ranges
Dual-in-line and Surface Mount Packages in Standard Pinouts
PCI-Compliant
Green Package Options (Pb/Halide-free/RoHS Complant) Available
•
•
•
•
•
ATF20V8B
ATF20V8BQ
ATF20V8BQL
Block Diagram
TSSOP
Pin Configurations
CLK/IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
GND
All Pinouts Top View
I
Logic Inputs
I/O
Bi-directional Buffers
OE
Output Enable
*
No Internal Connection
VCC
+5V Supply
DIP/SOIC
CLK/IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
GND
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
PLCC
VCC
IN
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IN
OE/IN
IN
IN
CLK/IN
*
VCC
IN
I/O
Clock
IN
IN
IN
*
IN
IN
IN
4
3
2
1
28
27
26
CLK
5
6
7
8
9
10
11
25
24
23
22
21
20
19
12
13
14
15
16
17
18
Function
VCC
IN
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IN
OE/IN
24
23
22
21
20
19
18
17
16
15
14
13
I/O
I/O
I/O
*
I/O
I/O
I/O
Rev. 0407J–07/06
IN
IN
GND
*
OE/IN
IN
I/O
Pin Name
1
2
3
4
5
6
7
8
9
10
11
12
1
Description
The ATF20V8B is a high-performance CMOS (electricallyerasable) programmable logic device (PLD) that utilizes
Atmel’s proven electrically-erasable Flash memory technology. Speeds down to 7.5 ns and power dissipation as low
as 10 mA are offered. All speed ranges are specified over
the full 5V ± 10% range for industrial temperature ranges,
and 5V ± 5% for commercial temperature ranges.
Several low-power options allow selection of the best solution for various types of power-limited applications. Each of
these options significantly reduces total system power and
enhances system reliability.
The ATF20V8Bs incorporate a superset of the generic
architectures, which allows direct replacement of the 20R8
family and most 24-pin combinatorial PLDs. Eight outputs
are each allocated eight product terms. Three different
modes of operation, configured automatically with software, allow highly complex logic functions to be realized.
Absolute Maximum Ratings*
Temperature Under Bias................................ -55°C to +125°C
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Note:
Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns.Maximum output pin voltage is VCC + 0.75V DC which
may overshoot to 7.0V for pulses of less than 20
ns.
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on Input Pins
with Respect to Ground
During Programming.....................................-2.0V to +14.0V(1)
Programming Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
1.
DC and AC Operating Conditions
Operating Temperature (Ambient)
VCC Power Supply
2
ATF20V8B(Q)(L)
Commercial
Industrial
0°C - 70°C
-40°C - 85°C
5V ± 5%
5V ± 10%
ATF20V8B(Q)(L)
DC Characteristics
Symbol
Parameter
Condition
IIL
Input or I/O Low
Leakage Current
0 ≤ VIN ≤ VIL(Max)
IIH
Input or I/O High
Leakage Current
3.5 ≤ VIN ≤ VCC
Min
Typ
Max
Units
-35
-100
µA
10
µA
Com.
60
90
mA
Ind.
60
100
mA
B-15
Com.
60
80
mA
B-15
Ind.
60
90
mA
B-25
Com.
60
80
mA
B-25
Ind.
60
90
mA
BQ-10
Com.
35
55
mA
BQL-15
Com.
5
10
mA
BQL-15
Ind.
5
15
mA
BQL-25
Com.
5
10
mA
BQL-25
Ind.
5
15
mA
Com.
80
110
mA
Ind.
80
125
mA
B-15
Com.
60
90
mA
B-15
Ind.
60
105
mA
B-25
Com.
60
90
mA
B-25
Ind.
60
105
mA
BQ-10
Com.
40
55
mA
BQL-15
Com.
20
35
mA
BQL-15
Ind.
20
40
mA
BQL-25
Com.
20
35
mA
BQL-25
Ind.
20
40
mA
-130
mA
B-7, -10
ICC
Power Supply
Current, Standby
VCC = Max,
VIN = Max,
Outputs Open
B-7, -10
ICC2
Clocked Power
Supply Current
VCC = Max,
Outputs Open,
f = 15 MHz
IOS(1)
Output Short
Circuit Current
VIL
Input Low Voltage
-0.5
0.8
V
VIH
Input High Voltage
2.0
VCC + 0.75
V
0.5
V
VOL
Output Low Voltage
0.5
V
VOH
Notes:
Output High Voltage
VOUT = 0.5V
VIN = VIH or VIL,
VCC = Min
VIN = VIH or VIL,
VCC = Min
IOL = 24 mA
Com.,
Ind.
IOL = 16 mA
IOH = -4.0 mA
2.4
V
1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec.
2. Shaded parts are obsolete with a last time buy date of 19 August 1999.
3
AC Waveforms(1)
Note:
1.
Timing measurement reference is 1.5V. Input AC driving levels are 0.0V and 3.0V, unless otherwise specified.
AC Characteristics(1)
-7
-10
-15
-25
Symbol
Parameter
tPD
Input or Feedback to
Non-Registered Output
tCF
Clock to Feedback
tCO
Clock to Output
2
tS
Input or Feedback
Setup Time
5
7.5
12
15
ns
tH
Hold Time
0
0
0
0
ns
tP
Clock Period
8
12
16
24
ns
tW
Clock Width
4
6
8
12
ns
fMAX
8 outputs switching
Min
Max
Min
Max
Min
Max
Min
Max
Units
3
7.5
3
10
3
15
3
25
ns
7
1 output switching
ns
3
5
6
2
7
8
2
10
2
10
ns
12
ns
External Feedback 1/(tS + tCO)
100
68
45
37
MHz
Internal Feedback 1/(tS + tCF)
125
74
50
40
MHz
No Feedback 1/(tP)
125
83
62
41
MHz
tEA
Input to Output Enable — Product Term
3
9
3
10
3
15
3
20
ns
tER
Input to Output Disable —Product Term
2
9
2
10
2
15
2
20
ns
tPZX
OE pin to Output Enable
2
6
2
10
2
15
2
20
ns
tPXZ
OE pin to Output Disable
1.5
6
1.5
10
1.5
15
1.5
20
ns
Note:
4
1.
See ordering information for valid part numbers and speed grades.
2.
Shaded -25 parts are obsolete with a last-time buy date of August 19, 1999.
3.
Shaded -7 and -15 parts are obsolete with a last-time buy date of September 30, 2006.
ATF20V8B(Q)(L)
ATF20V8B(Q)(L)
Input Test Waveforms and
Measurement Levels
Output Test Loads
Commercial
tR, tF < 5 ns (10% to 90%)
Pin Capacitance
f = 1 MHz, T = 25°C(1)
Typ
Max
Units
Conditions
CIN
5
8
pF
VIN = 0V
COUT
6
8
pF
VOUT = 0V
Note:
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
Power-up Reset
The registers in the ATF20V8Bs are designed to reset during power-up. At a point delayed slightly from VCC crossing
VRST, all registers will be reset to the low state. As a result,
the registered output state will always be high on power-up.
This feature is critical for state machine initialization. However, due to the asynchronous nature of reset and the
uncertainty of how VCC actually rises in the system, the following conditions are required:
1. The VCC rise must be monotonic,
2. After reset occurs, all input and feedback setup
times must be met before driving the clock pin high,
and
3. The clock must remain stable during tPR.
Preload of Registered Outputs
Parameter
Description
Typ
Max
Units
tPR
Power-up Reset Time
600
1,000
ns
VRST
Power-up Reset Voltage
3.8
4.5
V
The ATF16V8B’s registers are provided with circuitry to
allow loading of each register with either a high or a low.
This feature will simplify testing since any state can be
forced into the registers to control test sequencing. A
JEDEC file with preload is generated when a source file
with vectors is compiled. Once downloaded, the JEDEC file
preload sequence will be done automatically by most of the
approved programmers after the programming.
Security Fuse Usage
Electronic Signature Word
Programming/Erasing
There are 64 bits of programmable memory that are always
available to the user, even if the device is secured. These
bits can be used for user-specific data.
Programming/erasing is performed using standard PLD
programmers. For further information, see the Configurable
Logic Databook, section titled, “CMOS PLD Programming
Hardware and Software Support.”
A single fuse is provided to prevent unauthorized copying
of the ATF20V8B fuse patterns. Once programmed, fuse
verify and preload are inhibited. However, the 64-bit User
Signature remains accessible.
The security fuse should be programmed last, as its effect
is immediate.
5
Input and I/O Pull-ups
All ATF20V8B family members have internal input and I/O
pull-up resistors. Therefore, whenever inputs or I/Os are
not being driven externally, they will float to V CC . This
ensures that all logic array inputs are at known states.
These are relatively weak active pull-ups that can easily be
overdriven by TTL-compatible drivers (see input and I/O
diagrams below).
Input Diagram
I/O Diagram
Functional Logic Diagram Description
The Logic Option and Functional Diagrams describe the
ATF20V8B architecture. Eight configurable macrocells can
be configured as a registered output, combinatorial I/O,
combinatorial output, or dedicated input.
The ATF20V8B can be configured in one of three different
modes. Each mode makes the ATF20V8B look like a different device. Most PLD compilers can choose the right
mode automatically. The user can also force the selection
by supplying the compiler with a mode selection. The determining factors would be the usage of register versus combinatorial outputs and dedicated outputs versus outputs
with output enable control.
The ATF20V8B universal architecture can be programmed
to emulate many 24-pin PAL devices. These architectural
6
ATF20V8B(Q)(L)
subsets can be found in each of the configuration modes
described in the following pages. The user can download
the listed subset device JEDEC programming file to the
PLD programmer, and the ATF20V8B can be configured to
act like the chosen device. Check with your programmer
manufacturer for this capability.
Unused product terms are automatically disabled by the
compiler to decrease power consumption. A security fuse,
when programmed, protects the content of the ATF20V8B.
Eight bytes (64 fuses) of User Signature are accessible to
the user for purposes such as storing project name, part
number, revision, or date. The User Signature is accessible regardless of the state of the security fuse.
ATF20V8B(Q)(L)
Compiler Mode Selection
Registered
Complex
Simple
Auto Select
ABEL, Atmel-ABEL
P20V8R
P20V8C
P20V8
P20V8
CUPL
G20V8MS
G20V8MA
(1)
G20V8
(1)
G20V8A
(1)
LOG/iC
GAL20V8_R
GAL20V8_C7
GAL20V8_C8
GAL20V8
OrCAD-PLD
“Registered”
“Complex”
“Simple”
GAL20V8
PLDesigner
P20V8
P20V8
P20V8
P20V8
Tango-PLD
G20V8
G20V8
G20V8
G20V8
Note:
1. Only applicable for version 3.4 or lower.
ATF20V8B Registered Mode
PAL Device Emulation/PAL Replacement. The registered
mode is used if one or more registers are required. Each
macrocell can be configured as either a registered or combinatorial output or I/O, or as an input. For a registered output or I/O, the output is enabled by the OE pin, and the
register is clocked by the CLK pin. Eight product terms are
allocated to the sum term. For a combinatorial output or
I/O, the output enable is controlled by a product term, and
seven product terms are allocated to the sum term. When
the macrocell is configured as an input, the output enable is
permanently disabled.
Any register usage will make the compiler select this mode.
The following registered devices can be emulated using
this mode:
20R8
20RP8
20R6
20RP6
20R4
20RP4
Registered Mode Operation
7
Registered Mode Logic Diagram
8
ATF20V8B(Q)(L)
ATF20V8B(Q)(L)
ATF20V8B Complex Mode
PAL Device Emulation/PAL Replacement. In the complex
Mode, combinatorial output and I/O functions are possible.
Pins 1 and 11 are regular inputs to the array. Pins 13
through 18 have pin feedback paths back to the AND-array,
which makes full I/O capability possible. Pins 12 and 19
(outermost macrocells) are outputs only. They do not have
input capability. In this mode, each macrocell has seven
product terms going to the sum term and one product term
enabling the output.
Combinatorial applications with an OE requirement will
make the compiler select this mode. The following devices
can be emulated using this mode:
20L8
20H8
20P8
Complex Mode Operation
ATF20V8B Simple Mode
PAL Device Emulation/PAL Replacement. In the Simple
Mode, 8 product terms are allocated to the sum term. Pins
15 and 16 (center macrocells) are permanently configured
as combinatorial outputs. Other macrocells can be either
inputs or combinatorial outputs with pin feedback to the
AND-array. Pins 1 and 11 are regular inputs.
The compiler selects this mode when all outputs are combinatorial without OE control. The following simple PALs can
be emulated using this mode:
14L8 14H8 14P8
16L6 18H6 16P6
18L4 18H4 18P4
20L2 20H2 20P2
Simple Mode Option
9
Complex Mode Logic Diagram
10
ATF20V8B(Q)(L)
ATF20V8B(Q)(L)
Simple Mode Logic Diagram
11
12
ATF20V8B(Q)(L)
ATF20V8B(Q)(L)
13
14
ATF20V8B(Q)(L)
ATF20V8B(Q)(L)
ATF20V8B Ordering Information
tPD (ns)
tS (ns)
tCO (ns)
Ordering Code
Package
7.5
5
5
ATF20V8B-7JC
ATF20V8B-7PC
ATF20V8B-7SC
ATF20V8B-7XC
28J
24P3
24S
24X
Commercial
(0°C to 70°C)
10
7.5
7
ATF20V8B-10JC
ATF20V8B-10PC
ATF20V8B-10SC
ATF20V8B-10XC
28J
24P3
24S
24X
Commercial
(0°C to 70°C)
ATF20V8B-10JI
ATF20V8B-10PI
ATF20V8B-10SI
ATF20V8B-10XI
28J
24P3
24S
24X
Industrial
(-40°C to 85°C)
ATF20V8B-15JC
ATF20V8B-15PC
ATF20V8B-15SC
ATF20V8B-15XC
28J
24P3
24S
24X
Commercial
(0°C to 70°C)
ATF20V8B-15JI
ATF20V8B-15PI
ATF20V8B-15SI
ATF20V8B-15XI
28J
24P3
24S
24X
Industrial
(-40°C to 85°C)
15
Note:
12
10
Operation Range
1. Shaded parts are obsolete with a last-time buy date of September 30, 2006.
ATF20V8B Green Package Options (Pb/Halide-free/RoHS Compliant)
tPD (ns)
tS (ns)
tCO (ns)
10
7.5
7
Ordering Code
Package
ATF20V8B-10JU
ATF20V8B-10PU
28J
24P3
Operation Range
Industrial
(-40°C to 85°C)
Using “C” Product for Industrial
To use commercial product for Industrial temperature ranges, down-grade one speed grade from the “I” to the “C” device
(7 ns “C” = 10 ns “I”) and de-rate power by 30%.
Package Type
28J
28-lead, Plastic J-leaded Chip Carrier (PLCC)
24P3
24-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
24S
24-lead, 0.300" Wide, Plastic Gull-wing Small Outline (SOIC)
24X
24-lead, 4.4 mm Wide, Plastic Thin Shrink Small Outline (TSSOP)
15
ATF20V8BQ and ATF20V8BQL Ordering Information
tPD (ns)
tS (ns)
tCO (ns)
10
7.5
15
15
Note:
Ordering Code
Package
Operation Range
7
ATF20V8BQ-10JC
ATF20V8BQ-10PC
ATF20V8BQ-10XC
28J
24P3
24X
Commercial
(0°C to 70°C)
12
10
ATF20V8BQL-15JC
ATF20V8BQL-15PC
ATF20V8BQL-15SC
ATF20V8BQL-15XC
28J
24P3
24S
24X
Commercial
(0°C to 70°C)
12
10
ATF20V8BQL-15JI
ATF20V8BQL-15PI
ATF20V8BQL-15SI
ATF20V8BQL-15XI
28J
24P3
24S
24X
Industrial
(-40°C to 85°C))
1. Shaded parts are obsolete with a last-time buy date of September 30, 2006.
ATF20V8BQL Green Package Options (Pb/Halide-free/RoHS Compliant)
tPD (ns)
tS (ns)
tCO (ns)
15
12
10
Note:
Ordering Code
Package
ATF20V8BQL-15JU
ATF20V8BQL-15PU
28J
24P3
Operation Range
Industrial
(-40°C to 85°C))
1. Shaded parts are obsolete with a last-time buy date of September 30, 2006.
Using “C” Product for Industrial
To use commercial product for Industrial temperature ranges, down-grade one speed grade from the “I” to the “C” device
(7 ns “C” = 10 ns “I”) and de-rate power by 30%.
Package Type
28J
28-lead, Plastic J-leaded Chip Carrier (PLCC)
24P3
24-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
24S
24-lead, 0.300" Wide, Plastic Gull-wing Small Outline (SOIC)
24X
24-lead, 4.4 mm Wide, Plastic Thin Shrink Small Outline (TSSOP)
16
ATF20V8B(Q)(L)
ATF20V8B(Q)(L)
Packaging Information
28J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
E1
D2/E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-018, Variation AB.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
12.319
–
12.573
D1
11.430
–
11.582
E
12.319
–
12.573
E1
11.430
–
11.582
D2/E2
9.906
–
10.922
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
28J, 28-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
28J
B
17
24P3 – PDIP
D
PIN
1
E1
A
SEATING PLANE
A1
L
B
B1
e
E
COMMON DIMENSIONS
(Unit of Measure = mm)
C
eC
eB
Notes:
1.
2.
This package conforms to JEDEC reference MS-001, Variation AF.
Dimensions D and E1 do not include mold Flash or Protrusion.
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").
MIN
NOM
MAX
A
–
–
5.334
A1
0.381
–
–
D
31.623
–
32.131
E
7.620
–
8.255
E1
6.096
–
7.112
B
0.356
–
0.559
B1
1.270
–
1.651
L
2.921
–
3.810
C
0.203
–
0.356
eB
–
–
10.922
eC
0.000
–
1.524
SYMBOL
e
NOTE
Note 2
Note 2
2.540 TYP
6/1/04
R
18
2325 Orchard Parkway
San Jose, CA 95131
TITLE
24P3, 24-lead (0.300"/7.62 mm Wide) Plastic Dual
Inline Package (PDIP)
ATF20V8B(Q)(L)
DRAWING NO.
24P3
REV.
D
ATF20V8B(Q)(L)
24S – SOIC
B
D1
D
PIN 1 ID
PIN 1
e
E
A
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
0º ~ 8º
L1
L
SYMBOL
MIN
NOM
MAX
A
–
–
2.65
A1
0.10
–
0.30
D
10.00
–
10.65
D1
7.40
–
7.60
E
15.20
–
15.60
B
0.33
–
0.51
L
0.40
–
1.27
L1
0.23
–
0.32
e
NOTE
1.27 BSC
06/17/2002
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC)
DRAWING NO.
REV.
24S
B
19
24X – TSSOP
Dimensions in Millimeter and (Inches)*
JEDEC STANDARD MO-153 AD
Controlling dimension: millimeters
0.30(0.012)
0.19(0.007)
4.48(0.176)
6.50(0.256)
4.30(0.169)
6.25(0.246)
PIN 1
0.65(0.0256)BSC
7.90(0.311)
1.20(0.047)MAX
7.70(0.303)
0.15(0.006)
0.05(0.002)
0.20(0.008)
0º ~ 8º
0.09(0.004)
0.75(0.030)
0.45(0.018)
04/11/2001
R
20
2325 Orchard Parkway
San Jose, CA 95131
TITLE
24X, 24-lead (4.4 mm body width) Plastic Thin Shrink Small Outline
Package (TSSOP)
ATF20V8B(Q)(L)
DRAWING NO.
REV.
24X
A
ATF20V8B(Q)(L)
Revision History
Revision Level – Release Date
History
J – July 2006
Ordering Information tables updated to reflect obsolete parts.
21
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High-Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2006 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are ® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
0407J–07/06
Similar pages