HT6P20X Series 224 OTP Encoder Features · Operating voltage: 2V~12V · One time programmable process · Low power consumption · Data active: D0~D3 · Built-in oscillator needs only 5% resistor · Minimal external components · 2/4 data selectable · HT6P20B: 8-pin DIP/SOP package · 224 maximum address and data codes HT6P20D: 16-pin DIP/NSOP package · Easy interface with an RF or IR medium Applications · Burglar alarm system · Security system · Smoke and fire alarm system · Cordless telephones · Garage door controllers · Other remote control systems · Car door controllers General Description The HT6P20X is a CMOS LSI encoder designed for remote control system applications. It encodes 24 bits of information and then serially transmits it via the DOUT pin upon receipt of transmission enable (DATA pins: D0~D3) signals. The combination of address and data bits of the HT6P20X is designed using one time pro- grammable process. In addition, the chip offers various packaging for flexible combination of programmable address/data so as to meet various applications. Its programmable address/data is transmitted together with the anti-code bits via RF or infrared transmission medium upon receipt of a trigger signal. Block Diagram O S C 1 O S C 2 V P P S IO O s c illa to r A d d re s s C o u n te r P r o g r a m m in g C ir c u it M ix e r & D r iv e r C o n tr o l U n it D a ta L a tc h P G M D 0 D O U T D 3 Note: Address/Data numbers are available in various combinations, refer to the functional description. Rev. 1.70 1 May 17, 2010 HT6P20X Series Pin Assignment 2 2 -A d d re s s 2 -D a ta 2 0 -A d d re s s 4 -D a ta D 1 1 1 6 D 0 D 2 2 1 5 P G M D 3 3 1 4 S IO V S S 4 1 3 V P P D 0 1 8 N C N C 5 1 2 V D D D 1 2 7 V D D N C 6 1 1 D O U T V S S 3 6 D O U T N C 7 1 0 O S C 2 4 5 O S C 1 N C 8 H T 6 P 2 0 B 8 D IP /S O P O S C 1 9 O S C 2 H T 6 P 2 0 D 1 6 D IP /N S O P Pin Description HT6P20D Pin No. Pin Name I/O Internal Connection I CMOS IN Pull-high Description 16 1~3 D0~D3 Data input and transmission enable (active low) They can be externally set to VSS or left open. 4 VSS ¾ ¾ Negative power supply, ground 5~8 NC ¾ ¾ No connection 9 OSC2 O OSCILLATOR Oscillator output pin 10 OSC1 I OSCILLATOR Oscillator input pin 11 DOUT O CMOS OUT 12 VDD ¾ ¾ Positive power supply 13 VPP I ¾ Programming power supply, VDD for normal operation 14 SIO I/O CMOS IN/OUT 15 PGM I CMOS IN Pull-high Data serial transmission output Programming address/control code input and mode code output for mode verification Program mode control pin, active low Approximate Internal Connection Circuits C M O S IN /O U T C M O S IN P u ll- h ig h C M O S O U T V O S C IL L A T O R D D O S C 1 Rev. 1.70 2 O S C 2 May 17, 2010 HT6P20X Series Absolute Maximum Ratings Supply Voltage ...........................VSS-0.3V to VSS+12V Storage Temperature ............................-50°C to 125°C Input Voltage..............................VSS-0.3V to VDD+0.3V Operating Temperature...........................-20°C to 75°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Electrical Characteristics Symbol Ta=25°C Test Conditions Parameter VDD Conditions ¾ ¾ Min. Typ. Max. Unit 2 ¾ 12 V VDD Operating Voltage ISTB Standby Current 12V Oscillator stops ¾ 1 2 mA IDD Operating Current 12V No load, fOSC=3kHz ¾ 200 400 mA VIH ²H² Input Voltage ¾ ¾ 0.8VDD ¾ VDD V VIL ²L² Input Voltage ¾ ¾ 0 ¾ 0.2VDD V RPH D0~D3 Pull-high Resistance 12V ¾ ¾ 150 300 kW 5V 0.9VDD -2 -5 ¾ mA 12V 0.9VDD -6.5 -15 ¾ mA 5V 0.1VDD 2 5 ¾ mA 12V 0.1VDD 6 15 ¾ mA 12V ROSC=1.4MW ¾ 3 ¾ kHz Source IDOUT Output Current Sink fOSC Oscillator Frequency Functional Description Normal Operation The HT6P20X encodes and transmits address/data to a decoder upon receipt of a trigger signal. The transmission function of the HT6P20B/D is enabled by the D0~D3 pins (active low). The following is the transmission timing of the HT6P20X: D 0 ~ D 3 < 1 w o rd > 1 w o rd E n c o d e r D O U T Transmission Timing A complete code word of the HT6P20D consists of 3 periods as shown below. fo s c D O U T 1 c lo c k 0 1 /3 b it p ilo t p e r io d ( 2 3 c lo c k s ) ( A 0 ~ A 1 9 , 6 0 c lo c k s ) a d d r e s s c o d e p e r io d ( D 3 ~ D 0 , 1 2 c lo c k s ) d a ta c o d e p e r io d 1 0 1 a n ti- c o d e p e r io d ( 4 b its ) A Complete Code Word for the HT6P20D Rev. 1.70 3 May 17, 2010 HT6P20X Series The HT6P20B/D detects the logic state of the internal programmed address and the external data pins, and then transmits the detected information during the code period. Each address/data bit can be set to one of the following two logic states: fo s c " O n e " "Z e ro " A d d re s s / D a ta b it Flowchart P o w e r o n S ta n d b y m o d e N o T r a n s m is s io n e n a b le d ? Y e s P ilo t/A d d r e s s /D a ta /A n ti- c o d e w o r d s tr a n s m itte d N o Rev. 1.70 T r a n s m is s io n s till e n a b le d 4 Y e s May 17, 2010 HT6P20X Series Application Circuits T r a n s m itte r C ir c u it T r a n s m itte r C ir c u it + 1 2 V 1 D 0 2 D 1 4 R o s c 5 8 + 1 2 V N C D O U T O S C 1 V S S D 0 1 0 0 W 7 V D D O S C 2 1 2 D 1 L E D 6 4 R o s c 3 5 D 1 1 6 D 0 D 2 P G M 3 D 3 S IO 1 4 4 V S S V P P 1 3 5 N C V D D 1 2 6 N C D O U T 1 1 N C O S C 1 1 0 N C O S C 2 8 D O U T O S C 1 V S S 1 D 1 2 D 2 P G M 3 D 3 S IO 1 5 + 1 2 V 0 .1 m F 6 3 V S S V P P 5 N C V D D 6 N C D O U T L E D R o s c 9 1 6 D 0 4 1 0 0 W H T 6 P 2 0 D R o s c @ 1 .4 M W Note: V D D T r a n s m itte r C ir c u it 2 7 1 0 0 W 7 H T 6 P 2 0 B R o s c @ 1 .4 M W T r a n s m itte r C ir c u it 1 N C O S C 2 H T 6 P 2 0 B R o s c @ 1 .4 M W 8 7 N C O S C 1 8 N C O S C 2 1 5 1 4 + 1 2 V 1 3 1 0 0 W 1 2 1 1 1 0 0 .1 m F R o s c 9 H T 6 P 2 0 D R o s c @ 1 .4 M W In order to prevent the IC from getting damaged due to the latch up, the 100W resistor or the LED which can also be a transmission indicator is indispensable. Rev. 1.70 5 May 17, 2010 HT6P20X Series Package Information 8-pin DIP (300mil) Outline Dimensions A 8 5 B 1 4 H C D I G E F Symbol Nom. Max. A 0.355 ¾ 0.375 B 0.240 ¾ 0.260 C 0.125 ¾ 0.135 D 0.125 ¾ 0.145 E 0.016 ¾ 0.020 0.070 F 0.050 ¾ G ¾ 0.100 ¾ H 0.295 ¾ 0.315 I ¾ 0.375 ¾ Symbol A Rev. 1.70 Dimensions in inch Min. Dimensions in mm Min. Nom. Max. 9.02 ¾ 9.53 B 6.10 ¾ 6.60 C 3.18 ¾ 3.43 D 3.18 ¾ 3.68 E 0.41 ¾ 0.51 F 1.27 ¾ 1.78 G ¾ 2.54 ¾ H 7.49 ¾ 8.00 I ¾ 9.53 ¾ 6 May 17, 2010 HT6P20X Series 16-pin DIP (300mil) Outline Dimensions A B A 1 6 9 1 8 B 1 6 9 1 8 H H C C D D G E G E I F I F Fig1. Full Lead Packages Fig2. 1/2 Lead Packages 16-pin DIP (300mil) Outline Dimensions · MS-001d (see fig1) Symbol Nom. Max. A 0.780 ¾ 0.880 B 0.240 ¾ 0.280 C 0.115 ¾ 0.195 D 0.115 ¾ 0.150 E 0.014 ¾ 0.022 F 0.045 ¾ 0.070 G ¾ 0.100 ¾ H 0.300 ¾ 0.325 I ¾ ¾ 0.430 Symbol Rev. 1.70 Dimensions in inch Min. Dimensions in mm Min. Nom. Max. A 19.81 ¾ 22.35 B 6.10 ¾ 7.11 C 2.92 ¾ 4.95 D 2.92 ¾ 3.81 E 0.36 ¾ 0.56 F 1.14 ¾ 1.78 G ¾ 2.54 ¾ H 7.62 ¾ 8.26 I ¾ ¾ 10.92 7 May 17, 2010 HT6P20X Series · MS-001d (see fig2) Symbol A Min. Nom. Max. 0.735 ¾ 0.775 B 0.240 ¾ 0.280 C 0.115 ¾ 0.195 D 0.115 ¾ 0.150 E 0.014 ¾ 0.022 F 0.045 ¾ 0.070 G ¾ 0.100 ¾ H 0.300 ¾ 0.325 I ¾ ¾ 0.430 Symbol Rev. 1.70 Dimensions in inch Dimensions in mm Min. Nom. Max. A 18.67 ¾ 19.69 B 6.10 ¾ 7.11 C 2.92 ¾ 4.95 D 2.92 ¾ 3.81 E 0.36 ¾ 0.56 F 1.14 ¾ 1.78 G ¾ 2.54 ¾ H 7.62 ¾ 8.26 I ¾ ¾ 10.92 8 May 17, 2010 HT6P20X Series · MO-095a (see fig2) Symbol A Min. Nom. Max. 0.745 ¾ 0.785 B 0.275 ¾ 0.295 C 0.120 ¾ 0.150 D 0.110 ¾ 0.150 E 0.014 ¾ 0.022 F 0.045 ¾ 0.060 G ¾ 0.100 ¾ H 0.300 ¾ 0.325 I ¾ ¾ 0.430 Symbol Rev. 1.70 Dimensions in inch Dimensions in mm Min. Nom. Max. A 18.92 ¾ 19.94 B 6.99 ¾ 7.49 C 3.05 ¾ 3.81 D 2.79 ¾ 3.81 E 0.36 ¾ 0.56 F 1.14 ¾ 1.52 G ¾ 2.54 ¾ H 7.62 ¾ 8.26 I ¾ ¾ 10.92 9 May 17, 2010 HT6P20X Series 8-pin SOP (150mil) Outline Dimensions 5 8 A B 4 1 C C ' G H D E a F · MS-012 Symbol Nom. Max. A 0.228 ¾ 0.244 B 0.150 ¾ 0.157 C 0.012 ¾ 0.020 C¢ 0.188 ¾ 0.197 D ¾ ¾ 0.069 E ¾ 0.050 ¾ F 0.004 ¾ 0.010 G 0.016 ¾ 0.050 H 0.007 ¾ 0.010 a 0° ¾ 8° Symbol Rev. 1.70 Dimensions in inch Min. Dimensions in mm Min. Nom. Max. A 5.79 ¾ 6.20 B 3.81 ¾ 3.99 C 0.30 ¾ 0.51 C¢ 4.78 ¾ 5.00 D ¾ ¾ 1.75 E ¾ 1.27 ¾ F 0.10 ¾ 0.25 G 0.41 ¾ 1.27 H 0.18 ¾ 0.25 a 0° ¾ 8° 10 May 17, 2010 HT6P20X Series 16-pin NSOP (150mil) Outline Dimensions 1 6 A 9 B 8 1 C C ' G H D E a F · MS-012 Symbol A Min. Nom. Max. 0.228 ¾ 0.244 B 0.150 ¾ 0.157 C 0.012 ¾ 0.020 C¢ 0.386 ¾ 0.394 D ¾ ¾ 0.069 E ¾ 0.050 ¾ F 0.004 ¾ 0.010 G 0.016 ¾ 0.050 H 0.007 ¾ 0.010 a 0° ¾ 8° Symbol A Rev. 1.70 Dimensions in inch Dimensions in mm Min. Nom. Max. 5.79 ¾ 6.20 B 3.81 ¾ 3.99 C 0.30 ¾ 0.51 C¢ 9.80 ¾ 10.01 D ¾ ¾ 1.75 E ¾ 1.27 ¾ F 0.10 ¾ 0.25 G 0.41 ¾ 1.27 H 0.18 ¾ 0.25 a 0° ¾ 8° 11 May 17, 2010 HT6P20X Series Product Tape and Reel Specifications Reel Dimensions D T 2 A C B T 1 SOP 8N Symbol Description Dimensions in mm A Reel Outer Diameter 330.0±1.0 B Reel Inner Diameter 100.0±1.5 C Spindle Hole Diameter D Key Slit Width T1 Space Between Flange T2 Reel Thickness 13.0 +0.5/-0.2 2.0±0.5 12.8 +0.3/-0.2 18.2±0.2 SOP 16N (150mil) Symbol Description A Reel Outer Diameter B Reel Inner Diameter C Spindle Hole Diameter D Key Slit Width T1 Space Between Flange T2 Reel Thickness Rev. 1.70 Dimensions in mm 330.0±1.0 100.0±1.5 13.0 +0.5/-0.2 2.0±0.5 16.8 +0.3/-0.2 22.2±0.2 12 May 17, 2010 HT6P20X Series Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 R e e l H o le IC p a c k a g e p in 1 a n d th e r e e l h o le s a r e lo c a te d o n th e s a m e s id e . SOP 8N Symbol Description Dimensions in mm 12.0 +0.3/-0.1 W Carrier Tape Width P Cavity Pitch 8.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 5.5±0.1 D Perforation Diameter D1 Cavity Hole Diameter P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 6.4±0.1 B0 Cavity Width 5.2±0.1 K0 Cavity Depth 1.55±0.1 1.50 +0.25/-0.00 2.1±0.1 t Carrier Tape Thickness C Cover Tape Width 0.30±0.05 9.3±0.1 NSOP 16N Symbol Description Dimensions in mm W Carrier Tape Width P Cavity Pitch 8.0±0.1 E Perforation Position 1.75±0.1 16.0±0.3 F Cavity to Perforation (Width Direction) D Perforation Diameter 1.55 +0.1/-0.0 D1 Cavity Hole Diameter 1.50 +0.25/-0.0 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 6.5±0.1 B0 Cavity Width 10.3±0.1 K0 Cavity Depth 2.1±0.1 7.5±0.1 t Carrier Tape Thickness 0.30±0.05 C Cover Tape Width 13.3±0.1 Rev. 1.70 13 May 17, 2010 HT6P20X Series Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shenzhen Sales Office) 5F, Unit A, Productivity Building, No.5 Gaoxin M 2nd Road, Nanshan District, Shenzhen, China 518057 Tel: 86-755-8616-9908, 86-755-8616-9308 Fax: 86-755-8616-9722 Holtek Semiconductor (USA), Inc. (North America Sales Office) 46729 Fremont Blvd., Fremont, CA 94538, USA Tel: 1-510-252-9880 Fax: 1-510-252-9885 http://www.holtek.com Copyright Ó 2010 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.70 14 May 17, 2010