MIC GBJ10005 Single phase glass passivated bridge rectifier Datasheet

SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER
CURRENT
FEATURES
GBJ
Plastic package has UL Flammability
Glassification 94V-0
Glass passivated chip junctions
High case dielectric strength of 1500 VRMS
High surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed
260℃/10 seconds, 0.375”(9.5mm) lead length
29.7-30.3
•
•
•
3.4-3.8
O
3 .4
.1 -
2.5±0.2
2.0-2.4
Case: molded plastic body
Terminal: Plated leads solderable per MIL-STD-750
Method 2026
Mounting position: Any (Note 3)
Mounting Torque: 6 in – 1bs max.
Weight: 0.15 ounce,4.0 gram
10.8-11.2
φ3
MECHANICAL DATA
•
•
4.4-4.8
O
19.7-20.3
3.0×45
2.7-3.1
3.8-4.2
17.0-18.0
•
•
•
•
•
10.0 Amperes
5.0
•
50 to 1000 Volts
VOLTAGE RANGE
GBJ10005 THRU GBJ1010
0.6-0.8
0.9-1.1
9.8-10.2 7.3-7.7 7.3-7.7
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
•
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
GBJ
SYMBOLS GBJ
VRRM
VRMS
VDC
Maximum Reverse Peak Repetitive Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward At T C=100℃(Note
Rectified Current,
At TA=40℃(Note
1)
2)
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC Method)
Rating for Fusing (t<8.3ms)
Maximum Instantaneous Forward Voltage drop
Per bridge element 5.0A
Maximum DC Reverse Current at
rated DC blocking voltage per element
TA=25℃
TA=125℃
Typical Junction Capacitance, per let
(Measured at 1.0MHz and applied reverse voltage of
4.0V)
Typical Thermal Resistance (Note 2 and 3)
Operating Junction Temperature Range
Storage Temperature Range
GBJ
GBJ
GBJ
GBJ
GBJ
10005
1001
1002
1004
1006
1008
1010
50
35
50
100
70
100
200
140
200
400
280
400
10
5.0
600
420
600
800
560
800
1000
700
100
I(AV)
UNIT
Volts
Volts
Volts
Amps
IFSM
170
Amps
I2 t
142
A2s
VF
1.0
Volts
IR
5.0
250
μA
CJ
60
pF
RJC
TJ
TSTG
2.2
(-55 to +150)
(-55 to +150)
℃/W
Notes: 1. Unit mounted on 150mm×150mm×1.6mm A1. Plate heatsink
2. Unit mounted on P.C.B. With 0.5×0.5”(1.2×1.2mm) copper pads and 0.375”(9.5mm) lead length
3. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum
Heat transfer with #6 screw
E-mail: [email protected]
Web Site: www.cnmic.com
℃
℃
SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER
50 to 1000Volts
VOLTAGE RANGE
GBJ10005 THRU GBJ1010
CURRENT
10.0 Amperes
RATINGS AND CHARACTERISTIC CURVES GBJ10005 THRU GBJ1010
FIG. 1- DERATING CURVE
OUTPUT RECTIFIED CURRENT
FIG. 2- MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
PEAK FORWARD SURGE,
CURRENT,(A)
AVERAGE FORWARD OUTPUT
CURRENT (A)
15
Heat-Sink Mounting. Tc
10
P.C.B. Mounting
5
200
100
1.0 Cycle
0
0
25
50
75
100
125
150
0
175
1
2
TEMPERATURE, ℃
FIG. 3- TYPICAL FORWORD
CHARACTERISTICS PER LGE
8 10
20
40
60
100
100
TA=125℃
INSTANTANEOUS REVERSE
CURRENT, (A)
INSTANTANEOUS FORWARD
CURRENT, (A )
6
FIG. 4- TYPICAL REVERSE CHARACTERISTICS
PER LEG
100
10
1
0.1
0.01
0.6
0.8
1.0
1.2
10
1
0.1
T A=25℃
0.01
1.4
0
20
40
60
80
100
INSTANTANEOUS FORWARD VOLTAGE,(V)
PERCENT OF RATED PEAK REVERSE VOLTAGE,(V )
FIG. 5- TYPICAL JUNCTION CAPACITANCE
PER LEG
FIG. 6- TYPICAL TRANSIENT THERMAL
IMPEDANCE
100
TRANSIENT THERMAL IMPEDANCE
(℃/W)
1000
JUNCTION CAPACITANCE, (pF)
4
NUMBER OF CYCLES AT 60 Hz
100
10
1
1
10
100
1
0.1
0.01
1
T, HEATING TIME (SEC.)
REVRESE VOLTAGE,( V)
E-mail: [email protected]
0.1
Web Site: www.cnmic.com
10
Similar pages