FR801 FR806 THRU 8.0 AMP FAST RECOVERY RECTIFIERS VOLTAGE RANGE 50 to 800 Volts CURRENT 8.0 Amperes FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability TO-220A 3.8 f +.2 HOLE THRU .412 (10.5) MAX. .108 (2.75) .248 (6.3) .040 (1.0) MAX. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any PIN 1 .050 (1.27) .595 (15.1) MAX. .550 (14.0) .158 (4.0) MIN. MAX. .051 MAX. (1.3) .040 MAX. (1.0) * Weight: 2.24 grams .180 (4.6) .200 (5.08) + .120 (3.05) PIN 1 + CASE PIN 2 Case Negative Suffix "R" + CASE PIN 2 Case Positive Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current FR801 50 35 50 FR802 100 70 100 FR803 200 140 200 .375"(9.5mm) Lead Length at Tc=75 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. FR804 400 280 400 FR805 600 420 600 FR806 UNITS 800 V 560 V V 800 8.0 A 200 1.3 10.0 A V A 200 250 150 -65 65 +150 500 A nS pF C RATING AND CHARACTERISTIC CURVES (FR801 THRU FR806) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) CHARACTERISTICS 100 40 10 12 10 8 Single Phase 6 Half Wave 60Hz Resistive Or Inductive Load 4 2 0 0 20 40 60 Tj=25 C 80 100 120 140 160 180 200 CASE TEMPERATURE,( C) Pulse Width 300us 1% Duty Cycle 1 0.1 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PEAK FORWARD SURGE CURRENT,(A) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PULSE GENERATOR (NOTE 2) ( ) 250 200 150 Sine Wave 100 JEDEC method 50 1 5 (+) 1W NONINDUCTIVE 2. Rise Time= 10ns max., Source Impedance= 50 ohms. | | | | | | | | 0 -0.25A 100 FIG.5-TYPICAL JUNCTION CAPACITANCE NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. +0.5A 50 10 NUMBER OF CYCLES AT 60Hz OSCILLISCOPE (NOTE 1) trr 8.3ms Single Half Tj=25 C 0 140 JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) 500 120 100 80 60 40 20 0 -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm .01 .05 .1 .5 1 REVERSE VOLTAGE,(V) 5 10 50 100