FR201 THRU FR207 2.0 AMPS. Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 2.0 Amperes DO-15 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Axial leads, solderable per MILSTD-202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260℃/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension Weight: 0.40 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FR FR Type Number 201 202 Maximum Recurrent Peak Reverse Voltage 50 100 V RRM Maximum RMS Voltage 35 70 V RMS Maximum DC Blocking Voltage 50 100 V DC Maximum Average Forward Rectified Current.375”(9.5mm) Lead Length @T A = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @ T A=25℃ at Rated DC Blocking Voltage @ T A=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance ( Note 3 ) Operating Temperature Range FR 203 FR 204 FR 205 FR 206 FR 207 200 140 200 400 280 400 600 420 600 800 1000 560 700 800 1000 Units V V V I(AV) 2.0 A IFSM 60 A VF 1.2 V IR 5.0 100 uA uA nS pF Trr Cj R θ JA R θ JL R θ JC TJ 150 250 30 60 18 5 -65 to +150 -65 to +150 T STG Notes:1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 10mm x 10mm on P.C.B. Storage Temperature Range - 406 - 500 O C/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (FR201 THRU FR207) FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 70 2.0 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT AMPERES FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1.5 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375"(9.5mm) Lead Length .5 60 50 40 8.3ms Single Half Sine Wave JEDEC Method 30 20 10 0 0 0 25 50 75 100 125 150 1 175 2 o 5 10 20 50 100 60 100 NUMBER OF CYCLES AT 60Hz AMBIENT TEMPERATURE. ( C) FIG.3- TYPICAL FORWARD CHARACTERISTICS FIG.4- TYPICAL JUNCTION CAPACITANCE 20 100 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 10 3.0 1.0 60 40 Tj=25 0C 20 0.3 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.1 10 2 1 4 6 10 20 REVERSE VOLTAGE. (V) .03 .01 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) FIG.5- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms - 407 - -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm 40