MC74LCX16244 Low-Voltage CMOS 16-Bit Buffer With 5 V−Tolerant Inputs and Outputs (3−State, Non−Inverting) http://onsemi.com The MC74LCX16244 is a high performance, non−inverting 16−bit buffer operating from a 2.3 to 3.6 V supply. The device is nibble controlled. Each nibble has separate Output Enable inputs which can be tied together for full 16−bit operation. High impedance TTL compatible inputs significantly reduce current loading to input drivers while TTL compatible outputs offer improved switching noise performance. A VI specification of 5.5 V allows MC74LCX16244 inputs to be safely driven from 5.0 V devices. The MC74LCX16244 is suitable for memory address driving and all TTL level bus oriented transceiver applications. The 4.5 ns maximum propagation delays support high performance applications. Current drive capability is 24 mA at the outputs. The Output Enable (OEn) inputs, when HIGH, disable the outputs by placing them in a HIGH Z condition. The MC74LCX16244 contains sixteen non−inverting buffers with 3−state 5.0 V−tolerant outputs. The device is nibble controlled with each nibble functioning identically, but independently. The control pins may be tied together to obtain full 16−bit operation. The 3−state outputs are controlled by an Output Enable (OEn) input for each nibble. When OEn is LOW, the outputs are on. When OEn is HIGH, the outputs are in the high impedance state. Features • • • • • • • • • • • • Designed for 2.3 V to 3.6 V VCC Operation 4.5 ns Maximum tpd 5.0 V Tolerant − Interface Capability With 5.0 V TTL Logic Supports Live Insertion and Withdrawal IOFF Specification Guarantees High Impedance When VCC = 0 V LVTTL Compatible LVCMOS Compatible 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current in All Three Logic States (20 mA) Substantially Reduces System Power Requirements Latchup Performance Exceeds 500 mA ESD Performance: ♦ Human Body Model >2000 V ♦ Machine Model >200 V These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant © Semiconductor Components Industries, LLC, 2012 July, 2012 − Rev. 10 1 48 1 TSSOP−48 DT SUFFIX CASE 1201 MARKING DIAGRAM 48 LCX16244G AWLYYWW 1 A WL YY WW G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 3 of this data sheet. Publication Order Number: MC74LCX16244/D MC74LCX16244 Table 1. PIN NAMES OE1 1 48 OE2 O0 2 47 D0 Pins Function 46 D1 OEn Output Enable Inputs 45 GND D0−D15 Inputs O2 5 44 D2 O0−O15 Outputs O3 6 43 D3 VCC 7 42 VCC O4 8 41 D4 O5 9 40 D5 O1 3 GND 4 1 39 GND GND 10 O6 11 38 D6 O7 12 37 D7 O8 13 36 D8 O9 14 35 D9 GND 15 34 GND O10 16 33 D10 O11 17 32 D11 VCC 18 31 VCC O12 19 30 D12 O13 20 29 D13 GND 21 28 GND O14 22 27 D14 O15 23 26 D15 OE4 24 25 OE3 OE3 OE1 48 OE4 OE2 D0:3 D4:7 O0:3 D8:11 O4:7 D12:15 25 24 O8:11 O12:15 One of Four Figure 2. Logic Diagram Figure 1. Pinout: 48−Lead (Top View) TRUTH TABLE OE1 D0:3 O0:3 OE2 D4:7 O4:7 OE3 D8:11 O8:11 OE4 D12:15 O12:15 L L L L L L L L L L L L L H H L H H L H H L H H H X Z H X Z H X Z H X Z H= L= Z= X= High Voltage Level Low Voltage Level High Impedance State High or Low Voltage Level and Transitions Are Acceptable; for ICC reasons, DO NOT FLOAT Inputs. http://onsemi.com 2 MC74LCX16244 ORDERING INFORMATION Package Shipping† MC74LCX16244DTG TSSOP−48 (Pb−Free) 39 Units / Rail M74LCX16244DTR2G TSSOP−48 (Pb−Free) 2500 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MAXIMUM RATINGS Symbol VCC Parameter Value DC Supply Voltage Condition Units −0.5 to +7.0 V V VI DC Input Voltage −0.5 ≤ VI ≤ +7.0 VO DC Output Voltage −0.5 ≤ VO ≤ +7.0 Output in 3−State V −0.5 ≤ VO ≤ VCC + 0.5 Output in HIGH or LOW State (Note 1) V IIK DC Input Diode Current −50 VI < GND mA IOK DC Output Diode Current −50 VO < GND mA +50 VO > VCC mA IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current Per Supply Pin ±100 mA ±100 mA −65 to +150 °C IGND DC Ground Current Per Ground Pin TSTG Storage Temperature Range MSL Moisture Sensitivity Level 1 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. IO absolute maximum rating must be observed. RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Operating Data Retention Only Min Typ Max 2.0 1.5 2.5, 3.3 2.5, 3.3 3.6 3.6 V VI Input Voltage 0 5.5 VO Output Voltage (HIGH or LOW State) (3−State) 0 0 VCC 5.5 IOH HIGH Level Output Current VCC = 3.0 V − 3.6 V VCC = 2.7 V − 3.0 V VCC = 2.3 V − 2.7 V −24 −12 −8 IOL LOW Level Output Current VCC = 3.0 V − 3.6 V VCC = 2.7 V − 3.0 V VCC = 2.3 V − 2.7 V +24 +12 +8 TA Operating Free−Air Temperature Dt/DV Units V V mA mA Input Transition Rise or Fall Rate, VIN from 0.8 V to 2.0 V, VCC = 3.0 V http://onsemi.com 3 −40 +85 °C 0 10 ns/V MC74LCX16244 DC ELECTRICAL CHARACTERISTICS TA = −40°C to +85°C Symbol VIH VIL VOH VOL Characteristic HIGH Level Input Voltage (Note 2) LOW Level Input Voltage (Note 2) HIGH Level Output Voltage LOW Level Output Voltage Condition Min 2.3 V ≤ VCC ≤ 2.7 V 1.7 2.7 V ≤ VCC ≤ 3.6 V 2.0 Max V 2.3 V ≤ VCC ≤ 2.7 V 0.7 2.7 V ≤ VCC ≤ 3.6 V 0.8 2.3 V ≤ VCC ≤ 3.6 V; IOL = 100 mA VCC − 0.2 VCC = 2.3 V; IOH = −8 mA 1.8 VCC = 2.7 V; IOH = −12 mA 2.2 VCC = 3.0 V; IOH = −18 mA 2.4 VCC = 3.0 V; IOH = −24 mA 2.2 Units V V 2.3 V ≤ VCC ≤ 3.6 V; IOL = 100 mA 0.2 V VCC = 2.3 V; IOL = 8 mA 0.6 VCC = 2.7 V; IOL = 12 mA 0.4 VCC = 3.0 V; IOL = 16 mA 0.4 VCC = 3.0 V; IOL = 24 mA 0.55 VCC = 3.6 V, VIN = VIH or VIL, VOUT = 0 to 3.6 V ±5 mA IOZ 3−State Output Current IOFF Power Off Leakage Current VCC = 0, VIN = 3.6 V or VOUT = 3.6 V 10 mA IIN Input Leakage Current VCC = 0 to 3.6 V, VIN = 3.6 V or GND ±5 mA ICC Quiescent Supply Current VCC = 3.6 V, VIN = 3.6 V or VOUT = 3.6 V 10 mA 2.3 ≤ VCC ≤ 3.6 V; VIH = VCC − 0.6 V 500 mA DICC Increase in ICC per Input 2. These values of VI are used to test DC electrical characteristics only. AC CHARACTERISTICS (tR = tF = 2.5 ns; RL = 500 W) TA = −40°C to +85°C VCC = 3.3 V ± 0.3 V CL = 50 pF Symbol Parameter VCC = 2.7 V CL = 50 pF VCC = 2.5 V ± 0.2 V CL = 30 pF Waveform Min Max Min Max Min Max Units tPLH tPHL Propagation Delay Input to Output 1 1.5 1.5 4.5 4.5 1.5 1.5 5.2 5.2 1.5 1.5 5.4 5.4 ns tPZH tPZL Output Enable Time to High and Low Level 2 1.5 1.5 5.5 5.5 1.5 1.5 6.3 6.3 1.5 1.5 7.2 7.2 ns tPHZ tPLZ Output Disable Time From High and Low Level 2 1.5 1.5 5.4 5.4 1.5 1.5 5.7 5.7 1.5 1.5 6.5 6.5 ns tOSHL tOSLH Output−to−Output Skew (Note 3) 1.0 1.0 ns 3. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH−to−LOW (tOSHL) or LOW−to−HIGH (tOSLH); parameter guaranteed by design. http://onsemi.com 4 MC74LCX16244 DYNAMIC SWITCHING CHARACTERISTICS TA = +25°C Symbol Characteristic Condition Min Typ Max Units VOLP Dynamic LOW Peak Voltage (Note 4) VCC = 3.3 V, CL = 50 pF, VIH = 3.3 V, VIL = 0 V VCC = 2.5 V, CL = 30 pF, VIH = 2.5 V, VIL = 0 V 0.8 0.6 V VOLV Dynamic LOW Valley Voltage (Note 4) VCC = 3.3 V, CL = 50 pF, VIH = 3.3 V, VIL = 0 V VCC = 2.5 V, CL = 30 pF, VIH = 2.5 V, VIL = 0 V −0.8 −0.6 V 4. Number of outputs defined as “n”. Measured with “n−1” outputs switching from HIGH−to−LOW or LOW−to−HIGH. The remaining output is measured in the LOW state. CAPACITIVE CHARACTERISTICS Symbol Condition Typical Units Input Capacitance VCC = 3.3 V, VI = 0 V or VCC 7 pF COUT Output Capacitance VCC = 3.3 V, VI = 0 V or VCC 8 pF CPD Power Dissipation Capacitance 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 20 pF CIN Parameter OEn VCC Vmi VCC Vmi tPZH Vmi Dn tPHL On 0V tPLH Vmo Vmo On VOH tPHZ tPZL Vmo VOL On WAVEFORM 1 − PROPAGATION DELAYS tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 ns 0V VOH VHZ tPLZ Vmo VLZ VOL WAVEFORM 2 − OUTPUT ENABLE AND DISABLE TIMES tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Figure 3. AC Waveforms Table 2. AC WAVEFORMS VCC Symbol 3.3 V ± 0.3 V 2.7 V 2.5 V ± 0.2 V Vmi 1.5 V 1.5 V VCC / 2 Vmo 1.5 V 1.5 V VCC / 2 VHZ VOL + 0.3 V VOL + 0.3 V VOL + 0.15 V VLZ VOH − 0.3 V VOH − 0.3 V VOH − 015 V http://onsemi.com 5 MC74LCX16244 VCC PULSE GENERATOR R1 DUT RT CL RL Figure 4. Test Circuit Table 3. TEST CIRCUIT Test Switch tPLH, tPHL Open tPZL, tPLZ 6 V at VCC = 3.3 ± 0.3 V 6 V at VCC = 2.5 ± 0.2 V Open Collector/Drain tPLH and tPHL 6V tPZH, tPHZ GND CL = CL = RL = RT = 50 pF at VCC = 3.3 ± 0.3 V or equivalent (includes jig and probe capacitance) 30 pF at VCC = 2.5 ± 0.2 V or equivalent (includes jig and probe capacitance) R1 = 500 W or equivalent ZOUT of pulse generator (typically 50 W) http://onsemi.com 6 6 V or VCC x 2 OPEN GND MC74LCX16244 PACKAGE DIMENSIONS 48X TSSOP−48 DT SUFFIX CASE 1201 ISSUE B K REF 0.12 (0.005) M T U S V S T U 25 SECTION N−N B −U− L 1 N 24 A −V− PIN 1 IDENT. DETAIL E D 0.076 (0.003) −T− SEATING DIM A B C D F G H J J1 K K1 L M N F PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSIONS A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. J J1 48 M 0.254 (0.010) K K1 ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ S C M 0.25 (0.010) −W− DETAIL E H G MILLIMETERS MIN MAX 12.40 12.60 6.00 6.20 −−− 1.10 0.05 0.15 0.50 0.75 0.50 BSC 0.37 −−− 0.09 0.20 0.09 0.16 0.17 0.27 0.17 0.23 7.95 8.25 0_ 8_ INCHES MIN MAX 0.488 0.496 0.236 0.244 −−− 0.043 0.002 0.006 0.020 0.030 0.0197 BSC 0.015 −−− 0.004 0.008 0.004 0.006 0.007 0.011 0.007 0.009 0.313 0.325 0_ 8_ RECOMMENDED SOLDERING FOOTPRINT 48X 48X 0.32 1.00 8.45 1 0.50 PITCH DIMENSIONS: MILLIMETERS ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74LCX16244/D