Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Features: • • • • • 0.125” (3.175 mm) slot width Choice of aperture (0.050” or 0.010” width) Choice of opaque or IR transmissive shell material Choice of mounting configurations Choice of lead spacing or wires Product Photo Here Description: The slotted optical sensors in this series provide the flexibility of a custom device from a standard product line. Building from a standard housing with a 0.125” (3.18mm) wide slot, the user can specify output logic state, output driver circuit, aperture width, aperture surface and mounting tab locations. Furthermore, an option of wire or PCB leads allows electrical interface flexibility. The device body is an opaque plastic which minimizes sensitivity to both visible and near-infrared external light sources which may impact operation. Aperture width choices provide different optical resolution for motion sensing. A covered aperture provides dust protection, while an open aperture provides maximum protection against external light sources. Phototransistor sensor devices are: OPB360, OPB370, OPB380, OPB390, OPB859, OPB860, OPB870, OPB880, OPB890. The OPB355 provides a photodiode detector, which has a lower linear output-versus-light. Wide electrical output current ranges are available. LED emissions are near-infrared (850-940nm). Custom electrical, wire and cabling services are available. Contact your local representative or OPTEK for more information. Compliant to EU RoHS Directive 2002/95/EC. OPB360, OPB370, OPB380, OPB390 OPB859 OPB860, OPB870, OPB880, OPB890 Applications: • • • • • OPB355 Non-contact object sensing 1 Assembly line automation 3 1 3 2 4 Machine automation Equipment safety Machine safety 2 4 Wire Colors Color # RoHS Description 1 Red 2 Black 3 4 White Green CONTAINS POLYSULFONE To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. ND Vibra-Tite Formula 3 evaporates fast without causing structural failure in OPTEK’s molded plastics. Applies to: OPB360, OPB370, OPB380, OPB390 and OPB860, OPB870, OPB880, OPB890. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue E 12/2012 Page 1 of 11 Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Part Number Guide — OPB355 OPB 3 X X X Optek Assembly Phototransistor Output Family Mounting Configurations: L - Emitter side mounting tab only N - No mounting tabs P - Sensor side mounting tab only T - Two mounting tabs Part Number Guide — OPB360 / OPB370 OPB 3 X X X X X Optek Assembly Sensor Aperture: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Phototransistor Output Family Emitter Sensor: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Discrete Shell Material: 6 - Covered (apertures not visible), PCB leads 7 - Open (apertures visible), PCB leads Mounting Configurations: L - Emitter side mounting tab only N - No mounting tabs P - Sensor side mounting tab only T - Two mounting tabs Lead Spacer Designator: 0 = 0.320” (8.12 mm) lead space 5 = 0.220” (5.59 mm) lead space Part Number Guide — OPB380 / OPB390 OPB 3 X 0 X X X Z Optek Assembly RoHS Compliant Phototransistor Output Family Sensor Aperture: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Discrete Shell Material: 8 - Covered (apertures not visible), Wires 9 - Open (apertures visible), Wires Emitter Sensor: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Mounting Configurations: L - Emitter side mounting tab only N - No mounting tabs P - Sensor side mounting tab only T - Two mounting tabs OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue E 12/2012 Page 2 of 11 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Part Number Guide — OPB859 OPB 8 5 9 Optek Assembly Phototransistor Output Family Emitter Aperture: 0.050” (1.270 mm) Sensor Aperture: 0.050” (1.270 mm) Mounting Configurations: T - Two mounting tabs Part Number Guide — OPB860 / OPB870 OPB 8 X X X X X Optek Assembly Sensor Aperture: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Phototransistor Output Family Emitter Sensor: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Discrete Shell Material: 6 - Covered (apertures not visible), PCB leads 7 - Open (apertures visible), PCB leads Electrical Specification Variations: 0 = Electrical Parameter A (lead spacing = 0.320”) 1 = Electrical Parameter B (lead spacing = 0.320”) 2 = Electrical Parameter C (lead spacing = 0.320”) 5 = Electrical Parameter A (lead spacing = 0.220”) 6 = Electrical Parameter B (lead spacing = 0.220”) 7 = Electrical Parameter C (lead spacing = 0.220”) Mounting Configurations: L - Emitter side mounting tab only N - No mounting tabs P - Sensor side mounting tab only T - Two mounting tabs Note: Assemblies with dual 0.010” apertures are currently available with electrical parameter “A” only. Part Number Guide — OPB880 / OPB890 OPB 8 X X X X X Z Optek Assembly RoHS Compliant Phototransistor Output Family Sensor Aperture: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Discrete Shell Material: 8 - Covered (apertures not visible), Wires 9 - Open (apertures visible), Wires Emitter Sensor: 1 - 0.010” (0.254 mm) 5 - 0.050” (1.270 mm) Electrical Specification Variations: 0 = Electrical Parameter A 1 = Electrical Parameter B 2 = Electrical Parameter C Mounting Configurations: L - Emitter side mounting tab only N - No mounting tabs P - Sensor side mounting tab only T - Two mounting tabs NOTE: Assemblies with dual 0.010” apertures are currently available with electrical parameter “A” only. Wires = 26AWG - 24” long. UL approved. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue E 12/2012 Page 3 of 11 Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 OPB355, OPB360, OPB370 E / Clear Top Denotes LED OPB380, OPB390 S / Black Top Denotes Sensor OPB880, OPB890 OPB859 Pin # Emitter Pin # Transistor/Diode 1 Anode 3 Collector / Anode 2 Cathode 4 Emitter / Cathode [ MILLIMETERS] DIMENSIONS ARE IN: INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue E 12/2012 Page 4 of 11 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 OPB860, OPB870 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue E 12/2012 Page 5 of 11 Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage Temperature(1) (2) OPB355, OPB360, OPB370, OPB859, OPB860, OPB870 Series OPB380, OPB390, OPB880, OPB890 Series Operating Temperature(1) (2) Lead Soldering Temperature -40° C to +100° C -40° C to +85° C -40° C to +85° C (7) 260° C Input LED Forward DC Current OPB355, OPB360, OPB370, OPB380, OPB390, OPB859, OPB860, OPB870, OPB880, OPB890 50 mA Peak Forward Current (1µs pulse width, 300 pps) 1A Reverse DC Voltage 2V Power Dissipation (2) 75 mW Output Phototransistor/Diode Cathode-Anode Reverse Voltage -OPB355 60 V Collector-Emitter Voltage OPB360, OPB370, OPB380, OPB390, OPB859, OPB860, OPB870, OPB880, OPB890 Series 30 V Emitter-Collector Voltage 5V Collector DC Current Power Dissipation 30 mA (1) 100 mW Notes: (1) For wire series (OPB380, OPB390, OPB880 and OPB890), maximum storage and operating temperature is limited by the temperature rating of the lead wires. (2) Derate linearly 1.67 mW/° C above 25° C. (3) For OPB355, OPB360 and OPB370, polarity is denoted by color of housing top: LED (clear); sensor (black). (4) Cleaning agents methanol and isopropanol are recommended. Spray or wipe; do not submerge. (5) OPB380 and OPB390 wire terminations have 24” of 7-strand 26 AWG UL approved insulated wire on each terminal. These devices incorporate a wire strain relief at the housing surface. The insulation colors and functions are: IRED anode (red); IRED cathode (black); phototransistor collector (white); phototransistor emitter (green). (6) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (7) All parameters were tested using pulse technique. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue E 12/2012 Page 6 of 11 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Transistor/Diode (See OP240 for additional information—for reference only) VF Forward Voltage - 1.3 1.8 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V Output Diode — OPB355 (See OPB950 for additional information — for reference only) VBR Reverse Diode Breakdown Voltage 60 - - V IR = 100 µA, IF = 0, EE = 0 VFD Forward Voltage Photodiode - - 1.2 V IF = 1 mA, IF = 0, EE = 0 ID Reverse Dark Current - - 60 nA VR = 30 V, EE = 0, IF = 0 Output Transistor (See OP550 for additional information—for reference only) V(BR)CEO Collector-Emitter Breakdown Voltage 30 - - V IC = 1 mA V(BR)ECO Emitter-Collector Breakdown Voltage 5 - - V IE = 100 µA Collector-Emitter Dark Current - - 100 nA VCE = 10 V, IF = 0, EE = 0 10 - 200 µa VR = 5 V, IF = 40 mA Collector-Emitter Saturation Voltage OPB859 OPB860/870/865/875 (Para. A) OPB861/871/866/876 (Para. B) OPB862/872/867/877 (Para. C) OPB880/890/ (Para. A) OPB881/891 (Para. B) OPB882/892 (Para. C) - - 0.4 0.4 0.4 0.6 0.4 0.4 0.6 V IC = 125 µA, IF = 20 mA IC = 400 µA, IF = 20 mA IC = 800 µA, IF = 20 mA IC = 1800 µA, IF = 20 mA IC = 400 µA, IF = 20 mA IC = 800 µA, IF = 10 mA IC = 1800 µA, IF = 20 mA On-State Collector Current OPB36X, OPB37X (T, N, L, P 11) OPB36X, OPB37X (T, N, L, P 51) OPB36X, OPB37X (T, N, L, P 55) OPB38X, OPB39X (T, N, L, P 11) OPB38X, OPB39X (T, N, L, P 51) OPB38X, OPB39X (T, N, L, P 55) 1.0 2.5 3.5 1.0 2.5 3.5 - 5 10 14 5 10 14 mA VCE = 0.4 V, IF = 20 mA OPB859 250 - - µA VCE = 10 V, IF = 20 mA OPB860/870/865/875 (Para. A) OPB861/871/866/876 (Para. B) OPB862/872/867/877 (Para. C) OPB880/890/ (Para. A) OPB881/891 (Para. B) OPB882/892 (Para. C 0.5 1.0 1.8 0.5 1.0 1.8 - - ICEO Coupled IL VCE(SAT) IC(ON) On-State Collector Current OPB355 (L, N, P, T) mA VCE = 10 V, IF = 20 mA VCE = 5 V, IF = 10 mA VCE = 0.6 V, IF = 20 mA VCE = 10 V, IF = 20 mA VCE = 5 V, IF = 10 mA VCE = 0.6 V, IF = 20 mA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue E 12/2012 Page 7 of 11 Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 OPB355 - Flag Next to Emitter OPB355 - Flag Next to Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC (ON) Response (mA) Typical IC (ON) Response (mA) 1.00 0.80 Right to Left Left to Right 0.60 0.40 Left to Right Right to Left 0.60 0.40 0.20 0.20 0.00 0.00 0.80 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 Displacement Distance (inches) 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPB355 - Flag in Middle of Slot 1.20 Top to Bottom 1.00 Typical IC (ON) Response (mA) 0 Top to Bottom 0.80 Right to Left Left to Right 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue E 12/2012 Page 8 of 11 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Aperture Configuration 11 Next - FlagtoNext to Emitter OPB370T11 - Flag Emitter Aperture Configuration 11Next - FlagtoNext to Sensor OPB370T11 - Flag Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 1.00 0.80 0.80 Left to Right Right to Left Right to Left Left to Right 0.60 0.60 0.40 0.40 0.20 0.20 0.00 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) Displacement Distance (inches) Aperture Configuration Flag inof Middle OPB370T11 - Flag11 in- Middle Slot of Slot 1.20 Top to Bottom Typical IC(ON) Response (mA) 1.00 Top to Bottom 0 0.80 Right to Left Left to Right 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Diisplacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue E 12/2012 Page 9 of 11 Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Aperture Configuration Flag Next Emitter OPB370N51 - Flag51in- Middle of to Slot Aperture Configuration 51Next - FlagtoNext to Sensor OPB370N51 - Flag Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 1.00 0.80 Left to Right Right to Left 0.60 0.40 0.20 0.80 Left to Right Right to Left 0.60 0.40 0.20 0.00 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.05 Displacement Distance (inches) 0.10 0.15 0.20 0.25 Displacement Distance (inches) Aperture Configuration 51 in - Flag in Middle OPB370N51 - Flag Middle of Slotof Slot 1.20 Top to Bottom Typical IC(ON) Response (mA) 1.00 0 Top to Bottom 0.80 Left to Right Right to Left 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue E 12/2012 Page 10 of 11 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch Series: OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 ApertureOPB380T55 Configuration 55 -Next FlagtoNext to Emitter - Flag Emitter Aperture Configuration 55Next - Flag to Sensor OPB380T55 - Flag toNext Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 1.00 0.80 Right to Left Left to Right 0.60 0.40 0.20 0.80 Right to Left Left to Right 0.60 0.40 0.20 0.00 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.05 Displacement Distance (inches) 0.10 0.15 0.20 0.25 Displacement Distance (inches) Aperture Configuration Flag in of Middle OPB380T55 - Flag55in- Middle Slot of Slot 1.20 Top to Bottom 1.00 Top to Bottom Typical IC(ON) Response (mA) 0 0.80 Right to Left Left to Right 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue E 12/2012 Page 11 of 11