Burr-Brown OPA2734AIDGSR 0.05uv/ë c max, single-supply cmos operational amplifier Datasheet

OPA734, OPA2734
OPA735, OPA2735
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
0.05µV/°C max, SINGLE-SUPPLY CMOS
OPERATIONAL AMPLIFIERS
Zer∅-Drift Series
FEATURES
D
D
D
D
D
D
D
D
DESCRIPTION
The OPA734 and OPA735 series of CMOS operational
amplifiers use auto-zeroing techniques to simultaneously
provide low offset voltage (5µV max) and near-zero drift
over time and temperature. These miniature, high-precision, low quiescent current amplifiers offer high input
impedance and rail-to-rail output swing within 50mV of the
rails. Either single or bipolar supplies can be used in the
range of +2.7V to +12V (±1.35V to ±6V). They are
optimized for low-voltage, single-supply operation.
LOW OFFSET VOLTAGE: 5µV (max)
ZERO DRIFT: 0.05µV/°C max
QUIESCENT CURRENT: 750µA (max)
SINGLE-SUPPLY OPERATION
LOW BIAS CURRENT: 200pA (max)
SHUTDOWN
MicroSIZE PACKAGES
WIDE SUPPLY RANGE: 2.7V to 12V
The OPA734 family includes a shutdown mode. Under
logic control, the amplifiers can be switched from normal
operation to a standby current that is 9µA (max) and the
output placed in a high-impedance state.
APPLICATIONS
D
D
D
D
D
D
TRANSDUCER APPLICATIONS
TEMPERATURE MEASUREMENTS
ELECTRONIC SCALES
MEDICAL INSTRUMENTATION
BATTERY-POWERED INSTRUMENTS
HANDHELD TEST EQUIPMENT
The single version is available in the MicroSIZE SOT23-5
(SOT23-6 for shutdown version) and the SO-8 packages.
The dual version is available in the MSOP-8 and SO-8
packages (MSOP-10 only for the shutdown version). All
versions are specified for operation from −40°C to +85°C.
VREF = 15V
G=1+2
REF102
R3
RG
10V
R1
1kΩ
C1
1nF
1/2
OP A2735
R3
10kΩ
C4
1nF
C2
10nF
RG
C4
1nF
R3
10kΩ
R2
1kΩ
1/2
OP A2735
C3
1nF
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright  2003-2005, Texas Instruments Incorporated
! ! www.ti.com
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13.2V
Signal Input Terminals, Voltage(2) . . . . . . . . . . . (V−) − 0.5V to (V+) + 0.5V
Current(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10mA
Output Short Circuit(3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handled with appropriate precautions. Failure to observe
proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C
ESD Rating (Human Body Model), OPA734 . . . . . . . . . . . . . . . . . . . . 1000V
ESD Rating (Human Body Model), OPA735, OPA2734, OPA2735 . . . . 2000V
(1) Stresses above these ratings may cause permanent damage. Exposure
to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of
the device at these or any other conditions beyond those specified is not
implied.
(2) Input terminals are diode-clamped to the power-supply rails. Input signals
that can swing more than 0.5V beyond the supply rails should be current
limited to 10mA or less.
(3) Short-circuit to ground, one amplifier per package.
PACKAGE/ORDERING INFORMATION(1)
PRODUCT
PACKAGE-LEAD
PACKAGE
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT MEDIA,
QUANTITY
SOT23-6
″
SO-8
″
MSOP-10
″
DBV
″
D
″
DGS
″
−40°C to +85°C
″
−40°C to +85°C
″
−40°C to +85°C
″
NSB
″
OPA734A
″
BGO
″
OPA734AIDBVT
OPA734AIDBVR
OPA734AID
OPA734AIDR
OPA2734AIDGST
OPA2734AIDGSR
Tape and Reel, 250
Tape and Reel, 3000
Rails, 100
Tape and Reel, 2500
Tape and Reel, 250
Tape and Reel, 2500
SOT23-5
″
SO-8
″
SO-8
″
MSOP-8
″
DBV
″
D
″
D
″
DGK
″
−40°C to +85°C
″
−40°C to +85°C
″
−40°C to +85°C
″
−40°C to +85°C
″
NSC
″
OPA735A
″
OPA2735A
″
BGN
″
OPA735AIDBVT
OPA735AIDBVR
OPA735AID
OPA735AIDR
OPA2735AID
OPA2735AIDR
OPA2735AIDGKT
OPA2735AIDGKR
Tape and Reel, 250
Tape and Reel, 3000
Rails, 100
Tape and Reel, 2500
Rails, 100
Tape and Reel, 2500
Tape and Reel, 250
Tape and Reel, 2500
Shutdown Version
OPA734
″
OPA734
″
OPA2734
″
Non-Shutdown Version
OPA735
″
OPA735
″
OPA2735
″
OPA2735
″
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com.
2
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
ELECTRICAL CHARACTERISTICS: VS = ±5V (VS = +10V)
Boldface limits apply over the specified temperature range, TA = −40°C to +85°C.
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
OPA734, OPA2734, OPA735, OPA2735
PARAMETER
OFFSET VOLTAGE
Input Offset Voltage
vs Temperature
vs Power Supply
Long-Term Stability
Channel Separation, dc
INPUT BIAS CURRENT
Input Bias Current
over Temperature
Input Offset Current
NOISE
Input Voltage Noise, f = 0.01Hz to 1Hz
Input Voltage Noise, f = 0.1Hz to 10Hz
Input Voltage Noise Density, f = 1kHz
Input Current Noise Density, f = 1kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
CONDITIONS
VOS
dVOS/dT
PSRR
MIN
VS = 2.7V to 12V, VCM = 0V
IB
VCM = VS/2
IOS
VCM = VS/2
UNIT
1
0.01
0.2
Note (1)
0.1
5
0.05
1.8
µV
µV/°C
µV/V
µV/V
(V−) − 0.1V < VCM < (V+) − 1.5V
(V−) − 0.1
115
OPEN-LOOP GAIN
Open-Loop Voltage Gain
AOL
(V−) + 100mV < VO < (V+) − 100mV
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
GBW
SR
G = +1
115
RL = 10kΩ
f = 1MHz, IO = 0
CLOAD
ENABLE/SHUTDOWN
tOFF
tON(2)
VL (amplifier is shutdown)
VH (amplifier is active)
IQSD (per amplifier)
Input Bias Current of Enable Pin
130
(V+) − 1.5
V
dB
2
10
pF
pF
130
dB
1.6
1.5
MHz
V/µs
20
50
±20
125
See Typical Characteristics
ISC
pA
pA
pA
µVPP
µVPP
nV/√Hz
fA/√Hz
0.8
2.5
135
40
INPUT CAPACITANCE
Differential
Common-Mode
OUTPUT
Voltage Output Swing from Rail
Short-Circuit Current
Open-Loop Output Impedance
Capacitive Load Drive
MAX
±100
±200
See Typical Characteristics
±200
±300
en
en
en
in
VCM
CMRR
TYP
1.5
150
V−
(V−) + 2
4
3
(V−) + 0.8
V+
9
mV
mA
Ω
µs
µs
V
V
µA
µA
POWER SUPPLY
Operating Voltage Range
VS
Quiescent Current (per amplifier)
IQ
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SOT23-5, SOT23-6
MSOP-8, MSOP-10, SO-8
2.7 to 12
(±1.35 to ±6)
0.6
IO = 0
−40
−40
−65
qJA
200
150
V
0.75
mA
+85
+150
+150
°C
°C
°C
°C/W
°C/W
°C/W
(1) 300-hour life test at 150°C demonstrated randomly distributed variation in the range of measurement limits—approximately 1µV.
(2) Device requires one complete auto-zero cycle to return to V
OS accuracy.
3
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
PIN CONFIGURATIONS
Out
1
V−
2
+IN
3
OPA2735
OPA735
OPA735
5
4
V+
−IN
1
8
V+
V+
−IN A 2
7
OUT B
6
OUT
+IN A
3
6
−IN B
5
NC(1)
V−
4
5
+IN B
NC(1)
1
8
NC(1)
−IN
2
7
+IN
3
V−
4
OUT A
SOT23−5
SO−8, MSOP−8
SO−8
1
V−
+IN
NSB
Out
OPA2734
OPA734
OPA734
6
V+
2
5
Enable
3
4
−IN
NC(1)
1
8
Enable
−IN
2
7
V+
+IN
3
6
OUT
V−
4
5
NC(1)
SOT23−6(2)
OUT A
10 V+
−IN A 2
9
OUT B
+IN A
3
8
−IN B
V−
4
7
+IN B
Enable A
5
6
Enable B
SO−8
(1) NC = No Connection
(2) Pin 1 of the SOT23-6 is determined by orienting the package marking as shown in the diagram.
4
1
MSOP−10
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = ±5V (same as +10V).
OUTPUT VOLTAGE DRIFT PRODUCTION DISTRIBUTION
OUTPUT VOLTAGE PRODUCTION DISTRIBUTION
Offset Voltage (µV)
0.050
0.045
0.040
0.035
0.030
0.025
0.020
0.015
0.010
0.005
−5.0
−4.5
−4.0
−3.5
−3.0
−2.5
−2.0
−1.5
−1.0
−0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
Population
Population
Absolute Value;
Centered Around Zero
Offset Voltage Drift (µV/_ C)
OUTPUT VOLTAGE SWING TO RAIL
vs OUTPUT CURRENT
INPUT BIAS CURRENT vs TEMPERATURE
6
1000
4
−1000
Input Bias Current (pA)
VOUT Voltage Swing (V)
0
2
+85_ C
+25_C
0
−40_C
−2
−IB
−2000
−3000
−4000
−5000
10 Representative Units
−6000
−7000
−4
−8000
−6
−10000
−9000
0
5
10
15
20
25
30
+IB
VCM = V−
−50
35
−25
0
VCM = VS/2
600
+I B
400
200
0
−200
−I B
−400
75 85 100
125
800
Supply Current (µA)
Input Bias Current (pA)
800
50
SUPPLY CURRENT vs TEMPERATURE
INPUT BIAS CURRENT vs TEMPERATURE
1000
25
Temperature (_C)
Output Current (mA)
10 Representative Units
−600
600
±6V
400
±1.35V
200
−800
−1000
0
−50
−25
0
25
50
Temperature (_ C)
75 85 100
125
−50
−25
0
25
50
75
100
125
Temperature (_ C)
5
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±5V (same as +10V).
180
160
160
140
140
120
120
100
100
80
80
60
60
40
40
20
20
0
0
Output Voltage (2V/div)
LARGE−SIGNAL RESPONSE
180
Phase Margin (_)
AOL (dB)
OPEN−LOOP GAIN AND PHASE MARGIN
vs FREQUENCY
−20
−20
−40
0.1
1
10
100
1k
10k
100k
1M
−40
10M
Time (5µs/div)
Frequency (Hz)
SMALL−SIGNAL RESPONSE
POSITIVE OVERVOLTAGE RECOVERY
Voltage (2V/div)
Output Voltage (10mV/div)
Output
10 kΩ
1 0kΩ
+5V
OPA735
Input
− 5V
Time (250ns/div)
Time (2.5µs/div)
COMMON−MODE REJECTION RATIO vs FREQUENCY
NEGATIVE OVERVOLTAGE RECOVERY
140
1 0kΩ
120
10kΩ
+5 V
Input
− 5V
Output
CMRR (dB)
Voltage (2V/div)
100
OPA 73 5
80
60
40
20
0
Time (2.5µs/div)
1
10
100
1k
10k
Frequency (Hz)
6
100k
1M
10M
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±5V (same as +10V).
VOLTAGE NOISE vs FREQUENCY
POWER−SUPPLY REJECTION RATIO vs FREQUENCY
1k
160
140
+PSRR
Noise (nV/√Hz)
100
80
−PSRR
60
100
40
20
10
0
1
10
100
1k
10k
100k
1
1M
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
SAMPLING FREQUENCY vs TEMPERATURE
0.1Hz TO 10Hz NOISE
20.0
Sampling Frequency (kHz)
19.5
1µV/div
19.0
VS = 12V
18.5
18.0
17.5
17.0
VS = 2.7V
16.5
16.0
−50
1s/div
−25
0
25
50
75
100
125
150
Temperature (_C)
SMALL−SIGNAL OVERSHOOT vs CAPACITIVE LOAD
50
40
Overshoot (%)
PSRR (dB)
120
30
20
10
0
1
10
100
1000
Capacitance (pF)
7
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
APPLICATIONS INFORMATION
The OPA734 and OPA735 series of op amps are
unity-gain stable and free from unexpected output phase
reversal. They use auto-zeroing techniques to provide low
offset voltage and demonstrate very low drift over time and
temperature.
Good layout practice mandates the use of a 0.1µF
capacitor placed closely across the supply pins.
For lowest offset voltage and precision performance,
circuit layout and mechanical conditions should be
optimized. Avoid temperature gradients that create
thermoelectric (Seebeck) effects in thermocouple
junctions formed from connecting dissimilar conductors.
These thermally-generated potentials can be made to
cancel by assuring that they are equal on both input
terminals:
1.
Use low thermoelectric-coefficient connections
(avoid dissimilar metals).
2.
Thermally isolate components from power supplies
or other heat sources.
3.
Shield op amp and input circuitry from air currents
such as cooling fans.
Following these guidelines will reduce the likelihood of
junctions being at different temperatures, which can cause
thermoelectric voltages of 0.1µV/°C or higher, depending
on the materials used.
The logic input is a CMOS input. Separate logic inputs are
provided for each op amp on the dual version. For
battery-operated applications, this feature can be used to
greatly reduce the average current and extend battery life.
The enable time is 150µs, which includes one full
auto-zero cycle required by the amplifier to return to VOS
accuracy. Prior to returning to full accuracy, the amplifier
may function properly, but with unspecified offset voltage.
Disable time is 1.5µs. When disabled, the output assumes
a high-impedance state. The disable state allows the
OPA734 to be operated as a gated amplifier, or to have the
output multiplexed onto a common analog output bus.
INPUT VOLTAGE
The input common-mode range extends from (V−) − 0.1V
to (V+) − 1.5V. For normal operation, the inputs must be
limited to this range. The common-mode rejection ratio is
only valid within the specified input common-mode range.
A lower supply voltage results in lower input commonmode range; therefore, attention to these values must be
given when selecting the input bias voltage. For example,
when operating on a single 3V power supply, commonmode range is from 0.1V below ground to half the
power-supply voltage.
Normally, input bias current is approximately 100pA;
however, input voltages exceeding the power supplies can
cause excessive current to flow in or out of the input pins.
Momentary voltages greater than the power supply can be
tolerated if the input current is limited to 10mA. This is
easily accomplished with an input resistor, as shown in
Figure 1.
OPERATING VOLTAGE
The OPA734 and OPA735 op amp family operates with a
power-supply range of +2.7V to +12V (±1.35V to ±6V).
Supply voltages higher than +13.2V (absolute maximum)
can permanently damage the amplifier. Parameters that
vary over supply voltage or temperature are shown in the
Typical Characteristics section of this data sheet.
OPA734 ENABLE FUNCTION
The enable/shutdown digital input is referenced to the V−
supply voltage of the op amp. A logic HIGH enables the op
amp. A valid logic HIGH is defined as > (V−) + 2V. The valid
logic HIGH signal can be up to the positive supply,
independent of the negative power supply voltage. A valid
logic LOW is defined as < 0.8V above the V− supply pin.
If dual or split power supplies are used, be sure that logic
input signals are properly referred to the negative supply
voltage. The Enable pin is connected to internal pull-up
circuitry and will enable the device if this pin is left open
circuit.
8
Current−limited resistor required
if input voltage exceeds supply
rails by ≥ 0.5V.
+5V
IOVERLOAD
10mA max
50Ω
OPA735
VOUT
VIN
Figure 1. Input Current Protection
INTERNAL OFFSET CORRECTION
The OPA734 and OPA735 series of op amps use an
auto-zero topology with a time-continuous 1.6MHz op amp
in the signal path. This amplifier is zero-corrected every
100µs using a proprietary technique. Upon power-up, the
amplifier requires one full auto-zero cycle of approximately
100µs in addition to the start-up time for the bias circuitry
to achieve specified VOS accuracy. Prior to this time, the
amplifier may function properly but with unspecified offset
voltage.
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
Low-gain (< 20) operation demands that the auto-zero
circuitry correct for common-mode rejection errors of the
main amplifier. Because these errors can be larger than
0.1% of a full-scale input step change, one calibration
cycle (100µs) can be required to achieve full accuracy.
The term clock feedthrough describes the presence of the
clock frequency in the output spectrum. In auto-zeroed op
amps, clock feedthrough may result from the settling of the
internal sampling capacitor, or from the small amount of
charge injection that occurs during the sample-and-hold of
the op amp offset voltage. Feedthrough can be minimized
by keeping the source impedance relatively low (< 1kΩ)
and matching the source impedance on both input
terminals. If the source resistance is high (> 1kΩ)
feedthrough can generally be reduced with a capacitor of
1nF or greater in parallel with the source or feedback
resistors. See the circuit application examples.
1nF
VEX
R1
+10V
R R
R R
VOUT
OPA734
R1
VREF
1nF
Figure 2. Single Op Amp Bridge Amplifier Circuit
LAYOUT GUIDELINES
Attention to good layout practices is always recommended. Keep traces short. When possible, use a PCB
ground plane with surface-mount components placed as
close to the device pins as possible. Place a 0.1µF
capacitor closely across the supply pins. These guidelines
should be applied throughout the analog circuit to improve
performance and provide benefits such as reducing the
electromagnetic-interference (EMI) susceptibility.
VREF = 15V
2
G=1+2
REF102
10V
6
4
R1
1kΩ
R R
R R
R3
RG
C1(1)
1nF
1 /2
OP A 2 7 35
R3
10kΩ
C4
1nF
C2(1)
R
10nF G
C4
1nF
R3
10kΩ
R2
1kΩ
1 /2
OP A 2 7 35
C3(1)
1nF
NOTE: (1) Place close to input pins.
Figure 3. Differential Output Bridge Amplifier
9
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
C2 = 1nF
R4 = 10kΩ
+5V
R1
RF
300Ω
VIN
ADS8342
ADS8325
ADS1100
OPA735
R2
CF
500pF
0.1V to 4.9V
VREF
C1
1nF
R3
10kΩ
Optional filter for use
with SAR−type
converters
operating at
sampling rates of
50kHz and below.
VIN
VREF
R1
R2
±10V
±5V
0V to 10V
0V to 5V
5V
5V
5V
5V
42.2kΩ
20.8kΩ
20.8kΩ
10.5kΩ
14.7kΩ
19.6kΩ
5.11kΩ
10kΩ
Figure 4. Driving ADC
R4
10kΩ
C4
1µF
C3
1µF
R9
10kΩ
R5
1.5MΩ
+5V
R2
1kΩ
+5V
C2
100nF
OPA735
R7
10kΩ
−5V
−5V
REF1112
R1
22kΩ
−5V
TPS434 Thermopile
1/2
OPA2703
R3
6.8kΩ
R6
11kΩ
+5V
1/2
OPA2703
R8
10kΩ
−5V
NOTE: The TPS434, by Perkin Elmer Optoelectronics, is a thermopile detector
with integrated thermistor for cold−junction reference.
Figure 5. Thermopile Non-Contact Surface Temperature Measurement
10
VOUT
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
+5V
R1
536kΩ
R1
536kΩ
C3
10nF
−5V
R3
268kΩ
C1
5nF
VOUT
OPA735
C2
5nF
fn =
R = R 1 = R2 = 2R3
1
; where
C = C 1 = C2 = C3/2
2 π RC
(f n = 60Hz for values shown)
Figure 6. Twin-T Notch Filter
C2
68.0nF
R1
10.6kΩ
R2
2.64kΩ
1/2
R3
20.8kΩ
OP A2 735
1/2
VIN
C3
6.80nF
C1
15.0nF
O PA2735
VOUT
Cutoff frequency = 2kHz for values shown.
NOTE: FilterPro is a low-pass filter design program available for download at no cost from TI’s web site (www.ti.com).
The program can be used to easily determine component values for other cutoff frequencies or filter types.
Figure 7. High DC Accuracy, 3-Pole Low-Pass Filter
C1
1nF
R1 = 10 kΩ
R3
10 kΩ
R2
10 kΩ
1/2
OP A27 35
VOUT
VIN
C1
1nF
D1
NOTE: Dynamic range of the circuit is not reduced by
the diode voltage drop since the diode is not in the signal path.
Application Bulletin Precision Absolute Value Circuits (SBOA068)
is available at www.ti.com and provides further information about rectifier circuits.
1/2
OP A27 35
Figure 8. Precision Full-Wave Rectifier with Full Dynamic Range
11
"#$% &"#$
"#'% &"#'
www.ti.com
SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005
1nF
1kΩ
49kΩ
Enable A
G = 50
OPA734
VIN A
VOUT
Enable B
G=1
OPA734
VIN B
Enable inputs are CMOS logic compatible.
Figure 9. High-Precision 2-Input MUX for Programmable Gain
+VS
2.7V to 12V
Load
OPA735
Shunt
RS
10mΩ
VOUT = 1V/A
(referred to ground)
IL
R1
100Ω
R2
10kΩ
C1
1nF
Figure 10. Low-Side Power-Supply Current Sensing
12
PACKAGE OPTION ADDENDUM
www.ti.com
8-Feb-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA2734AIDGSR
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2734AIDGSRG4
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2734AIDGST
ACTIVE
MSOP
DGS
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2734AIDGSTG4
ACTIVE
MSOP
DGS
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AID
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDGKT
ACTIVE
MSOP
DGK
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDGKTG4
ACTIVE
MSOP
DGK
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2735AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AID
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDBVR
ACTIVE
SOT-23
DBV
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDBVRG4
ACTIVE
SOT-23
DBV
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDBVTG4
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA734AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA735AID
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA735AIDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
OPA735AIDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
OPA735AIDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
OPA735AIDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
8-Feb-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA735AIDG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA735AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA735AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-May-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
17-May-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
OPA2734AIDGST
DGS
10
MLA
330
12
5.3
3.4
1.4
8
12
PKGORN
T1TR-MS
P
OPA734AIDBVR
DBV
6
MLA
180
8
6.83
7.42
1.88
8
12
PKGORN
T3TR-MS
P
OPA734AIDBVT
DBV
6
MLA
180
8
6.83
7.42
1.88
8
12
PKGORN
T3TR-MS
P
OPA735AIDBVR
DBV
5
MLA
180
8
6.83
7.42
1.88
8
12
PKGORN
T3TR-MS
P
OPA735AIDBVT
DBV
5
MLA
180
8
6.83
7.42
1.88
8
12
PKGORN
T3TR-MS
P
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
OPA2734AIDGST
DGS
10
MLA
346.0
346.0
61.0
OPA734AIDBVR
DBV
6
MLA
0.0
0.0
0.0
OPA734AIDBVT
DBV
6
MLA
190.0
212.7
31.75
OPA735AIDBVR
DBV
5
MLA
190.0
212.7
31.75
OPA735AIDBVT
DBV
5
MLA
190.0
212.7
31.75
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-May-2007
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
Similar pages