Murata LQH44PN3R3MP0 Chip inductors (chip coils) for dc-dc converter wire wound type Datasheet

Inductors(coils)/Microchip Transformer > Chip Inductors (Chip Coils) > for DC-DC Converter Wire Wound Type
Data Sheet
Chip Inductors (Chip Coils)
1
for DC-DC Converter Wire Wound Type
LQH44P Series (1515 Size)
■ Packaging
Code
Packaging
Minimum Quantity
L
180mm Embossed Tape
1000
K
330mm Embossed Tape
3500
2.4 min.
3.5±0.2
4.0±0.2
4.0±0.2
0.35 min.
3.7±0.2
1.65±0.15
■ Dimensions
1.2±0.2 1.0 min. 1.2±0.2
(in mm)
■ Rated Value (p: packaging code)
Part Number
Inductance
Inductance
Allowable DC Current
Test Frequency (Based on Temperature Rise)
Allowable DC Current
(Based on Inductance Change)
DC Resistance
Self Resonance
Frequency (min.)
Class of Magnetic Shield
LQH44PN1R0NP0p
1.0µH±30%
1MHz
2450mA
2950mA
0.030ohm±20%
90MHz
Magnetic shield of magnetic powder in resin
LQH44PN2R2MP0p
2.2µH±20%
1MHz
1800mA
2500mA
0.049ohm±20%
70MHz
Magnetic shield of magnetic powder in resin
LQH44PN3R3MP0p
3.3µH±20%
1MHz
1770mA
2100mA
0.065ohm±20%
50MHz
Magnetic shield of magnetic powder in resin
LQH44PN4R7MP0p
4.7µH±20%
1MHz
1700mA
1700mA
0.080ohm±20%
40MHz
Magnetic shield of magnetic powder in resin
LQH44PN6R8MP0p
6.8µH±20%
1MHz
1340mA
1400mA
0.12ohm±20%
35MHz
Magnetic shield of magnetic powder in resin
LQH44PN100MP0p
10µH±20%
1MHz
1170mA
1150mA
0.16ohm±20%
25MHz
Magnetic shield of magnetic powder in resin
LQH44PN220MP0p
22µH±20%
1MHz
790mA
800mA
0.37ohm±20%
17MHz
Magnetic shield of magnetic powder in resin
Operating Temperature Range: -40°C to +85°C
Only for reflow soldering.
■ Notice (Allowable DC Current)
<Allowable DC Current>
When Allowable DC Current is applied to the
Products, self-generation of heat will rise to
40°C or less.
When Allowable DC Current is applied to the
Products, Inductance will be within +-30% of
nominal Inductance value.
Continued on the following page.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2009.1.8
http://www.murata.com/
Inductors(coils)/Microchip Transformer > Chip Inductors (Chip Coils) > for DC-DC Converter Wire Wound Type
Data Sheet
2
Continued from the preceding page.
■ Inductance - Frequency Characteristics (Typ.)
■ Inductance - Current Characteristics (Typ.)
100
1000
22µH
22µH
10µH
6.8µH
4.7µH
10
4.7µH
Inductance (µH)
Inductance (µH)
100
3.3µH
10
2.2µH
3.3µH
2.2µH
1
1.0µH
1
0.1
0.1
10µH
6.8µH
1.0µH
1
10
Frequency (MHz)
100
0.1
10
1000
100
DC Current (mA)
1000
10000
■ !Caution/Notice
!Caution (Rating)
Do not use products beyond the rated current as
this may create excessive heat.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profile
where peak solder temperature is below the Tin melting
point is used. Please confirm the solderability of Tin
plating termination chip before use.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2009.1.8
http://www.murata.com/
Similar pages