MMKP383 www.vishay.com Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type FEATURES • 7.5 mm to 37.5 mm lead pitch; 7.5 mm bent back pitch • Low contact resistance • Low loss dielectric • Small dimensions for high density packaging • Supplied loose in box and taped on reel or ammopack • Mounting: radial • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Where steep pulses occur e.g. SMPS (switch mode power supplies) • Electronic lighting e.g. ballast • Motor control circuits • S-correction • For flyback applications please use 1400 V series QUICK REFERENCE DATA Capacitance range (E24 series) 0.00047 μF to 4.7 μF Capacitance tolerance ±5% Climatic testing class according to IEC 60068-1 55/105/56 Rated DC temperature 85 °C Rated AC temperature 105 °C Maximum application temperature 105 °C Reference specifications IEC 60384-17 Dielectric Polypropylene film Electrodes Metallized Construction Mono and internal serial construction Encapsulation Flame retardant plastic case and epoxy resin UL-class 94 V-0 Leads Tinned wire C-value; tolerance; rated voltage; sub-class; manufacturer’s type; code for dielectric material; manufacturer location; manufacturer's logo; year and week Marking Note • For more detailed data and test requirements, contact [email protected] VOLTAGE RATINGS Rated DC voltage 250 400 630 1000 1400 1600 2000 Rated AC voltage 125 200 220 350 500 550 700 900 Rated peak to peak voltage 350 560 630 1000 1400 1600 2000 2500 Revision: 15-Jan-15 2500 Document Number: 28173 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents COMPOSITION OF CATALOG NUMBER Voltage (VDC) Example 147 Multiplier (nF) 470 pF 0.00047 μF 210 1 nF 0.001 μF 310 10 nF 0.01 μF 410 100 nF 0.1 μF 510 1000 nF 1.0 μF 610 10 000 nF 10.0 μF 0.1 2 1 3 Pitch Code 025 = 250 5 B 040 = 400 7.5 C 063 = 630 10 D 100 = 1000 15 F 140 = 1400 22.5 I 160 = 1600 27.5 K 200 = 2000 37.5 P 250 = 2500 1 0.01 P1 (mm) Capacitance Code (numerically) Special Code for Terminal 10 4 2 2 pins 100 5 4 4 pins P2 = 10.2 mm 1000 6 5 4 pins P2 = 20.3 mm (#) Customized 1 2 3456 7 89 MKP383 1 47 10 11 12 2 5 0 13 14 15 16 17 18 J I P 2 T 0 Special 0 = Standard Type Tolerance J Other = Special ± 5% A Special tolerance It (mm) Lead Length Code Pitch (mm) Packing Code Packing Style Remark 3.5 + 1.0/- 0.5 A ≤ 10 B/T Bulk/loose (1) Excluding bent back 3.5 ± 0.3 P ≥ 15 R Tape and reel; (H: 16.0 mm; 500 mm) For bent back only 5±1 M All Z Tape and reel; (H: 16.0 mm; 356 mm) For bent back only 25 ± 2 I 0: Space holder All H W Ammo (H: 16.0 mm) Tape and reel (H: 18.5 mm; 500 mm) For bent back only Pitch 5 mm to 22.5 mm G Ammo (H: 18.5 mm) Pitch ≤ 10 mm Notes • For detailed tape specifications refer to packaging information www.vishay.com/doc?28139 (1) Packaging will be bulk for all capacitors with pitch 15 mm and such with long leads (> 5 mm). Capacitors with short leads up to 5 mm and pitch > 15 mm will be in tray and asking code will be “T”. Revision: 15-Jan-15 Document Number: 28173 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents ELECTRICAL DATA (For Detailed Ratings go to www.vishay.com/doc?28183) URDC (V) CAP. (μF) 0.0068 min. 250 2.7 max. 0.0047 min. 400 1.5 max. 0.00047 min. 630 4.7 max. 0.0043 min. 1000 1.8 max. 0.0022 min. 1400 0.68 max. 0.0027 min. 1600 0.56 max. 0.0010 min. 2000 0.56 max. 0.0010 min. 2500 0.3 max. DIMENSIONS in millimeters l l w h w h h' F' lt (1) F Ø dt P H 10 Ø dt 15 w I Marking h Ø dt P1 ± 0.5 6 -2 P2 ± 0.5 Note (1) | F-F' | < 0.3 mm F = 7.5 mm + 0.6 mm / - 0.1 mm Ø dt ± 10 % of standard diameter specified Revision: 15-Jan-15 Document Number: 28173 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting on printed-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to packaging information www.vishay.com/doc?28139 Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board: • For original pitch = 15 mm the capacitors shall be mechanically fixed by the leads • For larger pitches the capacitors shall be mounted in the same way and the body clamped Space Requirements on Printed-Circuit Board The maximum space for length (lmax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed circuit board is shown in the drawings. For products with pitch 15 mm, w = l = 0.3 mm and h = 0.1 mm For products with 15 mm < pitch 27.5 mm, w =l = 0.5 mm and h = 0.1 mm For products with pitch = 37.5 mm, w = l = 0.7 mm and h = 0.5 mm Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned. wmax. = w + Δw Eccentricity Imax. = I + ΔI hmax. = h + Δh Seating plane SOLDERING CONDITIONS For general soldering conditions and wave soldering profile we refer to the document “Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171 STORAGE TEMPERATURE Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation RATINGS AND CHARACTERISTICS REFERENCE CONDITIONS Unless otherwise specified, all electrical values apply to an ambient free temperature of 23 °C ± 1 °C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %. For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. Revision: 15-Jan-15 Document Number: 28173 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents CHARACTERISTICS Impedance (Ω) 4 103 Δ C/C (%) 1 kHz 102 typical 2 101 max. 0 1 nF 100 100 nF -2 2.2 µF 10-1 -4 4.7 µF 10-2 -6 - 60 min. - 20 20 10-3 60 Tamb (°C) 100 104 Capacitance as a function of ambient temperature (typical curve) (1 kHz) 105 106 107 f (Hz) 108 Impedance as a function of frequency (typical curve) factor 1.2 1.0 0.8 0.6 0.4 0.2 0.0 - 50 - 20 20 60 Tamb (°C) 100 Max. DC and AC voltage as a function of temperature 103 103 85 °C < Tamb ≤ 105 °C, 250 VDC AC voltage (V) AC voltage (V) Tamb ≤ 85 °C, 250 VDC 100 nF 220 nF 470 nF 1.0 μF 2.2 μF 102 101 103 104 105 106 f (Hz) 107 Max. RMS voltage as a function of frequency Revision: 15-Jan-15 100 nF 220 nF 470 nF 1.0 μF 2.2 μF 102 101 102 103 104 105 106 f (Hz) 107 Max. RMS voltage as a function of frequency Document Number: 28173 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents 103 103 Tamb ≤ 85 °C, 400 VDC AC voltage (V) AC voltage (V) 85 °C < Tamb ≤ 105 °C, 400 VDC 10 47 nF 100 nF 470 nF 1.0 μF 2 101 103 104 105 10 106 f (Hz) 107 101 102 Max. RMS voltage as a function of frequency 103 103 47 nF 100 nF 220 nF 470 nF 1.0 μF 4.7 μF 104 105 106 7 f (Hz) 10 101 102 103 104 105 106 7 f (Hz) 10 Max. RMS voltage as a function of frequency AC voltage (V) AC voltage (V) 105 106 4.7 nF 10 nF 47 nF 220 nF 1.0 μF 102 7 f (Hz) 10 Max. RMS voltage as a function of frequency Revision: 15-Jan-15 47 nF 100 nF 220 nF 470 nF 1.0 μF 4.7 μF 85 °C < Tamb ≤ 105 °C, 1000 VDC 4.7 nF 10 nF 47 nF 220 nF 1.0 μF 104 106 f (Hz) 107 103 Tamb ≤ 85 °C, 1000 VDC 102 101 103 105 85 °C < Tamb ≤ 105 °C, 630 VDC 102 Max. RMS voltage as a function of frequency 103 104 AC voltage (V) AC voltage (V) 101 103 103 Max. RMS voltage as a function of frequency Tamb ≤ 85 °C, 630 VDC 102 47 nF 100 nF 470 nF 1.0 μF 2 101 102 103 104 105 106 7 f (Hz) 10 Max. RMS voltage as a function of frequency Document Number: 28173 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com 103 Tamb ≤ 85 °C, 1400 VDC 2.2 nF 4.7 nF 22 nF 100 nF 470 nF 102 101 103 104 105 106 7 f (Hz) 10 AC voltage (V) 85 °C < Tamb ≤ 105 °C, 1400 VDC AC voltage (V) 103 Vishay BCcomponents 102 101 102 Max. RMS voltage as a function of frequency 102 101 103 104 105 106 7 f (Hz) 10 7 f (Hz) 10 4.7 nF 10 nF 47 nF 100 nF 470 nF 101 102 103 104 105 106 7 f (Hz) 10 Max. RMS voltage as a function of frequency 85 °C < Tamb ≤ 105 °C, 2000 VDC AC voltage (V) AC voltage (V) 102 106 85 °C < Tamb ≤ 105 °C, 1600 VDC 103 1 nF 2.2 nF 10 nF 47 nF 100 nF 470 nF 105 102 Max. RMS voltage as a function of frequency 103 104 AC voltage (V) 4.7 nF 10 nF 47 nF 100 nF 470 nF 103 Max. RMS voltage as a function of frequency 103 Tamb ≤ 85 °C, 1600 VDC AC voltage (V) 103 2.2 nF 4.7 nF 22 nF 100 nF 470 nF 1 nF 2.2 nF 10 nF 47 nF 100 nF 470 nF 102 Tamb ≤ 85 °C, 2000 VDC 101 103 104 105 106 7 f (Hz) 10 Max. RMS voltage as a function of frequency Revision: 15-Jan-15 101 102 103 104 105 106 7 f (Hz) 10 Max. RMS voltage as a function of frequency Document Number: 28173 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents 103 1 nF 2.2 nF 4.7 nF 10 nF 22 nF 220 nF 102 AC voltage (V) AC voltage (V) 103 102 Tamb ≤ 85 °C, 2500 VDC 10 85 °C < Tamb ≤ 105 °C, 2500 VDC 1 103 104 1 nF 2.2 nF 4.7 nF 10 nF 22 nF 220 nF 105 106 107 8 f (Hz) 10 101 102 Max. RMS voltage as a function of frequency 106 103 104 105 106 7 f (Hz) 10 Max. RMS voltage as a function of frequency RC (s) ΔT (°C) 12 8 105 4 104 0 0 20 40 60 80 100 Tamb (°C) Insulation resistance as a function of the ambient temperature Revision: 15-Jan-15 - 50 - 20 20 60 Tamb (°C) 100 Maximum allowed component temperature rise (T) as a function of the ambient temperature (Tamb) Document Number: 28173 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 Dissipation factor (x 10-4) www.vishay.com Vishay BCcomponents 1000 100 20 19 18 17 16 15 14 13 12 11 10 8 9 7 6 5 4 3 2 1 21 10 1 102 103 104 105 f (Hz) 106 Tangent of loss angle as a function of frequency (typical curve) 250 V: 0.0068 C 0.091 μF, curve 8 400 V: 0.0047 < C 0.047 μF, curve 5 630 V: 0.00047 < C 0.033 μF, curve 4 1000 V: C 0.01 μF, curve 2 0.1 < C 0.15 μF, curve 9 0.047 < C 0.068 μF, curve 6 0.033 < C 0.068 μF, curve 5 0.011 < C 0.027 μF, curve 3 0.15 < C 0.22 μF, curve 10 0.068 < C 0.1 μF, curve 7 0.068 < C 0.1 μF, curve 6 0.027 < C 0.047 μF, curve 4 0.22 < C 0.27 μF, curve 11 0.1 < C 0.2 μF, curve 8 0.1 < C 0.15 μF, curve 7 0.047 < C 0.062 μF, curve 5 0.27 < C 0.33 μF, curve 12 0.2 < C 0.24 μF, curve 12 0.15 < C 0.22 μF, curve 11 0.062 < C 0.075 μF, curve 6 0.33 < C 0.56 μF, curve 15 0.24 < C 0.36 μF, curve 13 0.22 < C 0.27 μF, curve 12 0.075 < C 0.1 μF, curve 7 0.56 < C 0.82 μF, curve 16 0.36 < C 0.43 μF, curve 14 0.27 < C 0.33 μF, curve 15 0.1 < C 0.15 μF, curve 8 0.82 < C 1.2 μF, curve 18 0.43 < C 0.56 μF, curve 16 0.33 < C 0.82 μF, curve 16 0.15 < C 0.22 μF, curve 9 1.2 < C 1.6 μF, curve 19 0.56 < C 1.1 μF, curve 17 0.82 < C 1 μF, curve 18 0.22 < C 0.3 μF, curve 10 1.6 < C 2.7 μF, curve 20 1.1 < C 1.5 μF, curve 18 1 < C 4.7 μF, curve 21 0.3 < C 1 μF, curve 16 1 < C 1.8 μF, curve 19 1400 V: C 0.0047 μF, curve 1 1600 V: C 0.0047 μF, curve 3 2000 V: C 0.0047 μF, curve 2 0.0051 < C 0.016 μF, curve 2 0.0051 < C 0.0091 μF, curve 4 0.0051 < C 0.033 μF, curve 3 0.0051 < C 0.015 μF, curve 2 0.016 < C 0.033 μF, curve 3 0.0091 < C 0.068 μF, curve 5 0.033 < C 0.091 μF, curve 4 0.015 < C 0.091 μF, curve 3 0.033 < C 0.051 μF, curve 4 0.068 < C 0.01 μF, curve 6 0.091 < C 0.56 μF, curve 14 0.091 < C 0.33 μF, curve 12 0.051 < C 0.068 μF, curve 5 0.01 < C 0.16 μF, curve 7 0.068 < C 0.082 μF, curve 6 0.16 < C 0.56 μF, curve 14 2500 V: C 0.0047 μF, curve 1 0.082 < C 0.2 μF, curve 7 0.2 < C 0.68 μF, curve 14 Revision: 15-Jan-15 Document Number: 28173 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY THICKNESS IN mW/°C Wmax. (mm) HEAT CONDUCTIVITY (mW/°C) PITCH 7.5 mm PITCH 10 mm PITCH 15 mm PITCH 22.5 mm PITCH 27.5 mm PITCH 37.5 mm 3.0 4 - - - - - 4.0 5 6.5 - - - - 4.5 5 - - - 5.0 6 7.5 10 - - - 6.0 - 9.0 11 19 - - 7.0 - - 12 21 - - 8.5 - - 16 25 - - 9.0 - - - - 31 - 10.0 - - 18 28 - - 11.0 - - - - 36 - 13.0 - - - - 42 - 15.0 - - - - 48 - 18.0 - - - - 57 - 18.5 - - - - - 89 21.0 - - - - 68 - 21.5 - - - - - 102 24.0 - - - - - 116 30.0 - - - - - 134 - POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of the free air ambient temperature. The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical information film capacitors with the typical tgd of the curves.”. The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details) or calculated by T = P/G: • T = component temperature rise (°C) • P = power dissipation of the component (mW) • G = heat conductivity of the component (mW/°C) MEASURING THE COMPONENT TEMPERATURE A thermocouple must be attached to the capacitor body as in: Thermocouple The temperature is measured in unloaded (Tamb) and maximum loaded condition (Tc). The temperature rise is given by T = Tc - Tamb. To avoid radiation or convection, the capacitor should be tested in a wind-free box. Revision: 15-Jan-15 Document Number: 28173 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents APPLICATION NOTE AND LIMITING CONDITIONS For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For information depending of the capacitance value and the number of parallel connections contact: [email protected] These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference suppression capacitors conforming the standards must be used. To select the capacitor for a certain application, the following conditions must be checked: 1. The peak voltage (Up) shall not be greater than the rated DC voltage (URDC) 2. The peak-to-peak voltage (Up-p) shall not be greater than the maximum (Up-p) to avoid the ionization inception level 3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and divided by the applied voltage. For all other pulses following equation must be fulfilled: T dU 2 dU 2 x ------- x dt < U RDC x ------- dt dt rated 0 T is the pulse duration 4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component temperature rise). 5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values mentioned in the table: “Heat Conductivity” 6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and surge voltages from the mains included). VOLTAGE CONDITIONS FOR 6 ABOVE ALLOWED VOLTAGES Tamb ≤ 85 °C 85 °C < Tamb ≤ 105 °C URAC URAC Maximum temperature RMS-over voltage (< 24 h) 1.25 x URAC 1.25 x URAC Maximum peak voltage (Vo-p) (< 2 s) 1.6 x URDC 1.1 x URDC Maximum continuous RMS voltage EXAMPLE C = 4n7 - 1600 V used for the voltage signal shown in next drawing. Up-p = 1000 V; Up = 900 V; T1 = 12 μs; T2 = 64 μs; T3 = 4 μs The ambient temperature is 80 °C. In case of failure, the oscillation is blocked. Checking conditions: 1. The peak voltage Up = 900 V is lower than 1600 VDC 2. The peak-to-peak voltage 1000 V is lower than 22 x 550 VAC = 1600 Up-p 3. The voltage pulse slope (dU/dt) = 1000 V/4 μs = 250 V/μs. This is lower than 8000 V/μs (see specific reference data for each version). 4. The dissipated power is 35 mW as calculated with fourier terms and typical tgd. The temperature rise for wmax. = 6.0 mm and pitch = 15 mm will be 35 mW / 11 mW/°C = 3.2 °C This is lower than 10 °C temperature rise at 80 °C, according graph. 5. Oscillation is blocked 6. Not applicable Revision: 15-Jan-15 Document Number: 28173 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents VOLTAGE SIGNAL Voltage Up Up-p Time T3 T1 T2 INSPECTION REQUIREMENTS General Notes Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and Specific Reference Data”. GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) 4.3.1 Initial measurements Capacitance Tangent of loss angle: for C 1 μF at 100 kHz or for C > 1 μF at 10 kHz 4.3 Robustness of terminations Tensile: load 10 N; 10 s Bending: load 5 N; 4 x 90° 4.4 Resistance to soldering heat Method: 1A Solder bath: 280 °C ± 5 °C Duration: 10 s 4.14 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5 min ± 0.5 min Recovery time: min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 1 % of the value measured initially Tangent of loss angle Increase of tan : 0.0005 for: C 100 nF or 0.001 for: 100 nF < C 470 nF or 0.0015 for: C > 470 nF Compared to values measured in 4.3.1 Revision: 15-Jan-15 As specified in chapters “General Data” of this specification No visible damage Document Number: 28173 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance Tangent of loss angle: for C 1 μF at 100 kHz or for C > 1 μF at 10 kHz 4.15 Solvent resistance of the marking Isopropylalcohol at room temperature Method: 1 Rubbing material: cotton wool Immersion time: 5.0 min ± 0.5 min 4.6 Rapid change of temperature A = -55 °C B = +105 °C 5 cycles Duration t = 30 min 4.7 Vibration Visual examination Mounting: see section “Mounting” for more information Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s2 (whichever is less severe) Total duration 6 h No visible damage 4.7.2 Final inspection Visual examination No visible damage 4.9 Shock Mounting: see section “Mounting” for more information Pulse shape: half sine Acceleration: 490 m/s2 Duration of pulse: 11 ms 4.9.3 Final measurements Visual examination No visible damage Capacitance |C/C| 2 % for pitch < 10 mm |C/C| 1 % for pitch > 10 mm of the value measured in 4.6.1 Tangent of loss angle Increase of tan : 0.0005 for: C 100 nF or 0.001 for: 100 nF < C 470 nF or 0.0015 for: C > 470 nF Compared to values measured in 4.6.1 Insulation resistance As specified in section “Insulation Resistance” of this specification Revision: 15-Jan-15 No visible damage Legible marking Document Number: 28173 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A and C1B 4.10 Climatic sequence 4.10.2 Dry heat 4.10.3 Damp heat cyclic Test Db, first cycle 4.10.4 Cold 4.10.6 Damp heat cyclic Test Db, remaining cycles 4.10.6.2 Final measurements Temperature: +105 °C Duration: 16 h Temperature: -55 °C Duration: 2 h Voltage proof = URDC for 1 min within 15 min after removal from testchamber No breakdown or flash-over Visual examination No visible damage Legible marking Capacitance For original pitch = 22.5 mm and 37.5 mm: |C/C| 2 % or for original pitch 15 mm: |C/C| 3 % of the value measured in 4.4.2 or 4.9.3 Tangent of loss angle Increase of tan : 0.0005 for: C 100 nF or 0.001 for: 100 nF < C 470 nF or 0.0015 for: C > 470 nF Compared to values measured in 4.3.1 or 4.6.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification SUB-GROUP C2 4.11 Damp heat steady state 56 days, 40 °C, 90 % to 95 % RH no load 4.11.1 Initial measurements Capacitance Tangent of loss angle at 1 kHz 4.11.3 Final measurements Voltage proof = URDC for 1 min within 15 min after removal from testchamber No breakdown or flash-over Visual examination No visible damage Legible marking Capacitance |C/C| 1 % of the value measured in 4.11.1 Tangent of loss angle Increase of tan : 0.0005 for: C 100 nF or 0.001 for: 100 nF < C 470 nF or 0.0015 for: C > 470 nF Compared to values measured in 4.11.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Revision: 15-Jan-15 Document Number: 28173 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MMKP383 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C3A 4.12.1 Endurance test at 50 Hz alternating voltage Duration: 2000 h 4.12.1.1 Initial measurements Voltage: 1.25 x URAC at 105 °C Capacitance Tangent of loss angle: for C 1 μF at 100 kHz or for C > 1 μF at 10 kHz 4.12.1.3 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 5 % compared to values measured in 4.12.1.1 Tangent of loss angle Increase of tan : 0.0005 for: C 100 nF or 0.001 for: 100 nF < C 470 nF or 0.0015 for: C > 470 nF Compared to values measured in 4.12.1.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Temperature charcteristics Initial measurements Intermediate measurements Capacitance Capacitance at -55 °C Capacitance at +20 °C Capacitance at +105 °C For -55 °C to +20 °C: +1 % |C/C| 3.75 % or for 20 °C to 105 °C: -6 % |C/C| 0 % Final measurements Capacitance As specified in section “Capacitance” of this specification. Insulation resistance As specified in section “Insulation Resistance” of this specification SUB-GROUP C4 4.2.6 4.13 Charge and discharge 10 000 cycles Charged to URDC Discharge resistance: U RDC R = --------------------------------------------5 x C x dU/dt 4.13.1 Initial measurements Capacitance Tangent of loss angle: for C 1 μF at 100 kHz or for C > 1 μF at 10 kHz 4.13.3 Final measurements Capacitance |C/C| 1 % compared to values measured in 4.13.1 Tangent of loss angle Increase of tan : 0.0005 for: C 100 nF or 0.001 for: 100 nF < C 470 nF or 0.0015 for: C > 470 nF Compared to values measured in 4.13.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Revision: 15-Jan-15 Document Number: 28173 15 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000