APA7063 Stereo 1.5W Audio Power Amplifier with DC Volume Control Features General Description • • • • • • The APA7063 is a monolithic integrated circuit that pro- • • • • • • • Operating Voltage: 3.3V to 5V DC Volume Control Interface, 0dB to –105dB Depop Circuitry Integrated Thermal shutdown protection circuitry High supply voltage ripple rejection Low Supply Current, IDD = 13mA at Stereo BTL Low Shutdown Current, IDD = 0.7µA Bridge-Tied Load (BTL) or Single-Ended-(SE) Modes Operation Output Power at 1% THD+N, VDD=5V -1.2 W/Ch (typ) into an 8Ω Load Output Power at 10% THD+N, VDD=5V -1.5 W/Ch (typ) into an 8Ω Load Low Crossover Distortion Low Quiescent Current Bridge-tied or Stereo(Single-ended) Configurations vides DC volume control, and a stereo bridged audio power amplifiers capable of producing 1.5W(1.2W) into 8Ω with less than 10%(1.0%) THD+N. APA7063 provides a volume control pin DC_Vol determines the attenuation of output of the amplifiers. The attenuator range is from 0dB (DC_Vol=0.7VDD) to –105dB (DC_Vol=0V) with 32 steps. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in the APA7063, that reduces pops and clicks noise during power up and when using the shutdown modes and protects the chip from being destroyed by over temperature failure. To simplify the audio system design applications, the APA7063 combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal. The APA7063 also features a shutdown function which keeps the supply current only 0.7µA (typ). Applications Pin Description • Portable and Desktop Computers • Multimedia Monitors • Portable Radios, PDAs, and Portable TVs SHUTDOWN 1 VCC DC Vol Vo1 Vin1 Vin2 2 3 4 5 6 Vo2 7 GND 8 16 15 14 13 12 11 10 9 + OUT1 VCC - OUT1 Bypass SE/BTL - OUT2 VCC + OUT2 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 1 www.anpec.com.tw APA7063 Ordering and Marking Information APA7063 Package Code J : P D IP - 1 6 Tem p. Range I : - 4 0 to 8 5 ° C H a n d lin g C o d e TU : Tube H a n d lin g C o d e Tem p. Range P ackag e C ode K : SO P - 16 TR : Tape & Reel APA7063 J : APA7063 XXXXX X X X X X - D a te C o d e APA7063 K : APA7063 XXXXX X X X X X - D a te C o d e Block Diagram 10KΩ SE/BTL 10KΩ + - Vo1 + OUT1 20KΩ 20KΩ + - + - Vin1 Bias + Vin2 - OUT1 Volume Control 32 steps Vo2 + Shutdown Bypass Power Management 20KΩ 20KΩ + VCC GND Click and Pop Suppression Circuitry 10KΩ - OUT2 + OUT2 10KΩ Absolute Maximum Ratings (Over operating free-air temperature range unless otherwise noted.) Symbol VDD TA TJ TSTG TS VESD Parameter Supply Voltage Operating Ambient Temperature Range Maximum Junction Temperature Storage Temperature Range Soldering Temperature,10 seconds Electrostatic Discharge Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 2 Rating 6 -40 to 85 150 -65 to +150 260 -2000 to 2000*1 Unit V °C °C °C °C V www.anpec.com.tw APA7063 Electical Characteristics Electrical Characteristics for Entire IC The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C Symbol VDD IDD ISD VIH VIL Parameter Test Conditions Supply Voltage Quiescent Power Supply Current Shutdown Current SE/BTL High Input Voltage SE/BTL Low Input Voltage Min. 3.3 VIN=0V, IO =0A VPIN 2= VDD APA7063 Typ. Max. 5.5 13 25 0.7 2.0 4 0.8 Unit V mA µA V V Electrical Characteristics for Volume Attenuators The following specifications apply for VDD= 5V. Limits apply for TA= 25°C Symbol CRANGE Parameter Attenuator Range Test Conditions Gain with VpIN 3=5V Attenuation with VpIN 3=0V APA7063 Min. Typ. Max. ±0.5 -100 -105 Unit dB Electrical Characteristics for BTL Mode Operation The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C Symbol VOS PO THD+N RSRR XTALK VN Parameter Test Conditions Output Offset Voltage Output Power VIN=0V THD=1%, f=1kHz RL=8Ω THD=10%, f=1kHz RL=8Ω Total Harmonic Distortion + Noise AVD =2, 20Hz<f<20kHz, RL=8Ω , PO =1W PO =340mW, RL=32Ω , Power Supply Rejection Ratio Channel Separation Output Noise Voltage Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 VRIPPLE=200mVRms , RL=8Ω CB=2.2µF, f=120Hz f=1kHz , C B=2.2µF RL=8Ω,A-Wtd Filter 3 APA7063 Typ. 5 Unit 1.2 W mV 1.5 0.3 1.0 % 74 dB 95 40 dB uV www.anpec.com.tw APA7063 Electical Characteristics (Cont.) Electrical Characteristics for SE Mode Operation The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C Symbol VDS PO Parameter Test Conditions Output Offset Voltage Output Power VIN=0V, THD=1%, f=1KHZ, RL=32KΩ THD=10%, f=1KHZ, RL=32K Ω THD+N Total Harmonic Distortion plus AV= 1,VOUT=1 VRMS, f=1KHZ, RL=1K Ω Noise PO= 75mW, RL=32KΩ, Av=1, f=1KHZ RSRR Power Supply Rejection Ratio VRIPPLE= 200mVRMS, f=120Hz,CB=2.2µF XTALK Channel Separation f=1KHZ, CB=2.2µF VN Output Noise Voltage RL=1KΩ, A-Wtd Filter APA7063 Typ. 100 95 100 0.01 0.05 58 95 30 Unit mV mW dB dB uV Pin Description Pin Name No I/O Shutdown 1 1 VDD DC_Vol Vo1 Vin1 Vin2 Vo2 GND 2,10,15 3 4 5 6 7 8 I O I I O +OUT2 9 O -OUT2 SE/BTL Bypass -OUT2 11 12 13 14 O I I O +OUT1 16 O Description Shutdown mode control signal input, place entire IC in shutdown mode when held high, Idd=0.7uA. Supply voltage input pin. Volume control function input pin. Channel 1 output for external feedback circuit. Audio input channel 1 Audio input channel 2 Channel 2 output for external feedback circuit. Ground connection for circuitry. Channel 2 positive output in BTL mode and high impedance state in SE mode. Channel 2 negative output in BTL mode and in SE mode. Mode control signal input, hold low for BTL mode, hold high for SE mode. Connect to voltage divider for internal mid_supply bias Channel 1 negative output in BTL mode and in SE mode. Channel 1 positive output in BTL mode and high impedance state in SE mode. Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 4 www.anpec.com.tw APA7063 Typical Application Circuit #8 1µF 220µ µF R_var Shutdown r*=R_var/50 VCC Ω 20kΩ R-in 1µ µF L-in DC_Vol VCC -OUT1 Vo1 Vbypass 20kΩ Ω Vi1 SE/BTL 20kΩ Ω Vi2 -OUT2 Vo2 VCC GND +OUT2 1µ µF Ω 20kΩ #8 +OUT1 Ω 1kΩ R-ch Ω 100kΩ 100kΩ Ω L-ch APA7063 Headphone jack µF 220µ 1kΩ Ω * Add a resistor to avoid volume control gain error at power on status. For the R_var with 10KΩ variable resistor, the recommended value of r is in range of 100~200Ω. Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 5 www.anpec.com.tw APA7063 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics 10 5 2 VDD=5V RL=8Ω Po=1.0W BTL 1 0.5 0.2 0.1 AV=8 AV=2 0.05 AV=4 0.02 0.01 20 50 100 200 500 1k 2k 5k 10k 20k 5 2 VDD=5V RL=16Ω Po=0.5W BTL 1 0.5 0.2 AV=4 0.1 AV=8 0.02 0.01 20 50 100 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) 10 2 VDD=5V RL=8Ω BTL 1 f=20kHz 0.5 0.2 0.1 f=1kHz 0.05 f=20Hz 0.02 0.01 10m 20m 50m 100m 200m 500m 1 2 Output Power (W) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 200 500 1k 2k 5k 10k 20k Frequency (Hz) Frequency (Hz) 5 AV=2 0.05 10 5 2 VDD=5V RL=16Ω BTL 1 0.5 f=20kHz 0.2 0.1 f=1kHz 0.05 f=20Hz 0.02 0.01 10m 20m 50m 100m 200m 500m 1 Output Power (W) 6 www.anpec.com.tw APA7063 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 10 VDD=5V RL=8Ω Po=0.25W SE 5 2 1 0.5 0.2 AV=1 0.1 0.05 AV=4 0.02 AV=2 0.01 20 50 100 200 500 1k 2k 5k 10k 20k 10 5 2 1 VDD=5V RL=32Ω Po=75mW SE 0.5 AV=1 0.1 0.05 AV=4 0.02 0.01 AV=2 0.005 0.002 0.001 20 50 100 200 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) 10 VDD=5V RL=10kΩ Vin=1Vrms SE 2 1 0.5 0.1 AV=1 0.05 0.02 AV=4 0.01 0.005 AV=2 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Froquency (Hz) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 1k 2k 5k 10k 20k Frequency (Hz) Frequency (Hz) 5 500 10 5 VDD=5V RL=8Ω SE 2 1 0.5 0.2 f=20kHz f=20Hz 0.1 0.05 f=1kHz 0.02 0.01 10m 20m 30m 50m 70m 200m 500m Output Power (W) 7 www.anpec.com.tw APA7063 10 5 2 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) VDD=5V RL=32Ω SE 1 0.5 f=20kHz 0.1 0.05 f=20Hz 0.02 0.01 f=1kHz 0.005 0.002 0.001 10m 20m 30m 50m 70m 100m 200m 10 5 2 VDD=5V RL=10kΩ SE 1 0.5 0.1 0.05 f=20kHz 0.02 0.01 0.005 0.001 100m 200m 300m THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) 10 2 VDD=3.3V RL=8Ω Po=0.4W BTL 1 0.5 0.2 0.1 AV=2 AV=8 0.05 0.02 0.01 20 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 f=20Hz 500m 800m 1 2 3 Output Voltage (V) Output Power (W)) 5 f=1kHz 0.002 10 5 2 VDD=3.3V RL=16Ω Po=0.2W BTL 1 0.5 0.2 0.1 AV=8 AV=2 0.05 0.02 0.01 20 AV=4 50 100 200 500 1k 2k 5k 10k 20k Output Power (W) 8 www.anpec.com.tw APA7063 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 10 5 VDD=3.3V RL=8Ω BTL 2 1 f=20kHz 0.5 0.2 f=1kHz 0.1 0.05 f=20Hz 0.02 0.01 10m 20m 30m 50m 80m 200m 400m 800m 10 5 2 VDD=3.3V RL=16Ω BTL 1 0.5 f=20kHz 0.2 0.1 f=1kHz 0.05 f=20Hz 0.02 0.01 10m 20m 30m 10 5 2 VDD=3.3V RL=8Ω Po=100mW SE 1 0.5 0.2 AV=1 0.1 0.05 AV=4 0.02 AV=2 0.01 20 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 200m 500m Output Power (W) THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Output Power (W) 50m 70m 10 5 2 VDD=3.3V RL=32Ω Po=35mW SE 1 0.5 0.2 AV=1 0.1 0.05 AV=4 0.02 0.01 20 AV=2 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) 9 www.anpec.com.tw APA7063 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 10 5 2 VDD=3.3V RL=10kΩ Vin=1Vp SE 1 0.5 0.2 0.1 AV=1 0.05 AV=2 0.02 AV=4 0.01 20 50 100 200 500 1k 2k 5k 10k 20k 10 5 2 1 0.5 0.1 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) VDD=3.3V RL=32Ω SE 1 0.5 0.2 f=20kHz 0.1 0.05 f=1kHz 0.02 f=20Hz 0.01 10m 12m 15m 20m 25m 30m 35m 42m 55m 0.05 f=1kHz 0.02 0.01 10m 20m 30m 50m 70m 100m 200m 10 5 VDD=3.3V RL=10kΩ SE 2 1 0.5 0.2 0.1 f=1kHz 0.05 f=20kHz 0.02 f=20Hz 0.01 100m 200m 300m 500m 700m 1 2 Output Voltage (V) Output Power (W) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 f=20Hz Output Power (W) 10 2 f=20kHz 0.2 Frequency (Hz) 5 VDD=3.3V RL=8Ω SE 10 www.anpec.com.tw APA7063 THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 10 5 2 VDD=5V RL=10kΩ docking 1 0.5 0.1 f=20kHz 0.05 0.02 f=1kHz 0.01 0.005 f=20Hz 0.002 0.001 100m 200m 300m 500m 800m 1 2 3 10 5 2 VDD=3.3V RL=10kΩ docking 1 0.5 0.2 0.1 f=20kHz 0.05 0.02 f=1kHz f=20Hz 0.006 100m 200m 300m 500m 700m 1 2 Output Voltage (V) Output Voltage (V) 100u 100u VN-Output Noise Voltage( V) VN-Output Noise Voltage( V) No filter No filter 50u A_wtd filter 20u 10u 5u 2u 1u 20 VDD=5V RL=8Ω Av=2V/V BTL 50 100 200 500 1k 2k 5k A_wtd filter 20u 10u 5u 2u 1u 20 10k 20k Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 50u VDD=5V RL=10kΩ Av=1V/V SE 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) 11 www.anpec.com.tw APA7063 Typical Characteristics (Cont.) +0 -40 VDD=5V RL=32Ω Po=75mW Av=1V/V SE -20 Crosstalk (dB) Crosstalk (dB) -20 +0 VDD=5V RL=8Ω Po=1W Av=2V/V BTL -60 -80 f=1kHz -100 -40 -60 -80 f=1kHz -100 f=20kHz f=20kHz -120 20 50 100 200 500 1k 2k 5k -120 20 10k 20k 50 100 Frequency (Hz) PD-Power Disspation (W) Cf=0.22µF Cf=0.1µF +8 Gain (dBV) 1k 2k 5k 10k 20k 0.7 +10 Cf=0.068µF +4 VDD=5V RL=8Ω Av=2V/V BTL +2 -0 20 500 Frequency (Hz) +12 +6 200 RL=8Ω 0.6 0.5 0.4 RL=16Ω 0.3 0.2 RL=32Ω VDD=5V THD<1% BTL 0.1 0 50 100 200 500 1k 2k 5k 10k 20k 0 0.5 0.75 1 1.25 1.5 Output Power (W) Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 0.25 12 www.anpec.com.tw APA7063 Typical Characteristics (Cont.) 20 0.2 No Load RL=8Ω 1 7.5 IDD-Supply Current (mA) PD-Power Disspation (W) 0.18 0.16 0.14 0.12 RL=16Ω 0.1 0.08 0.06 RL=32Ω VDD=5V THD<1% SE 0.04 0.02 0.05 0.1 0.15 0.2 0.25 0.3 0.35 1 2.5 BTL 10 7 .5 5 SE 2 .5 0 0 0 15 1 0.4 1 .5 2 2 Output Power (W) Output Power (W) 4 4 .5 5 5 .5 VDD=5V RL=32Ω SE 0.14 1.4 1.2 THD=10% 1 3 .5 0.16 VDD=5V RL=8Ω BTL 1.6 3 VDD-Supply Voltage (V) Output Power (W) 1.8 2 .5 THD=1% 0.8 0.6 0.4 0.12 0.1 0.08 THD=10% THD=1% 0.06 0.04 0.02 0.2 0 0 2.5 3 3.5 4 4.5 5 5.5 2.5 VDD-Supply Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 3 3.5 4 4.5 5 5.5 VDD-Supply Voltage (V) 13 www.anpec.com.tw APA7063 Typical Characteristics (Cont.) 3 0.8 VDD=5V BTL Output Power (W) Output Power (W) 2.5 2 1.5 1 THD=10% 0.5 VDD=5V SE 0.7 THD=1% 0.6 0.5 0.4 0.3 0.2 THD=10% THD=1% 0.1 0 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 4 Load Resistance (Ω) Load Resistance (Ω) 1.1 VDD=3.3V BTL 1 0.8 Output Power (W) Output Power (W) 0.9 0.7 0.6 0.5 0.4 0.3 THD=10% THD=1% 0.2 0.1 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 0.34 0.32 0.3 0.28 0.26 0.24 0.22 0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 VDD=3.3V SE THD=10% THD=1% 4 Load Resistance (Ω) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 Load Resistance (Ω) 14 www.anpec.com.tw APA7063 Typical Characteristics (Cont.) 20 0 +0 VDD=5V SE -10 -20 PRSS (dBgA) Gsin (dBV) -2 0 -4 0 -6 0 -8 0 VDD=5V Vin=200mVp RL=8Ω Cb=2.2µF SE/BTL -30 -40 -50 -60 -1 00 -70 -1 20 -80 20 0 .0 0 .5 1 .0 1 .5 2 .0 2 .5 3 .0 3 .5 4 .0 4 .5 5 .0 100 200 500 1k 2k 5k 20k Frequency (Hz) Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 50 15 www.anpec.com.tw APA7063 Packaging Information SO – 300mil ( Reference JEDEC Registration MS-013) D N H GAUGE PLANE E 1 2 3 A Millimeters 1 A1 B e L Variations- D Inches Variations- D Dim Min. Max. Variations Min. Max. Dim Min. Max. Variations Min. Max. A 2.35 2.65 SO-16 10.10 10.50 A 0.093 0.1043 SO-16 0.398 0.413 A1 0.10 0.30 SO-18 11.35 11.76 A1 0.004 0.0120 SO-18 0.447 0.463 B 0.33 0.51 SO-20 12.60 13 B 0.013 0.020 SO-20 0.496 0.512 D See variations SO-24 15.20 15.60 D See variations SO-24 0.599 0.614 E 7.40 SO-28 17.70 18.11 E SO-28 0.697 0.713 SO-14 8.80 9.20 e SO-14 0.347 0.362 e 7.60 1.27BSC 0.2914 0.2992 0.050BSC H 10 10.65 H 0.394 0.419 L 0.40 1.27 L 0.016 0.050 N See variations N See variations 0° φ1 φ1 8° Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 16 0° 8° www.anpec.com.tw APA7063 Packaging Information (Cont.) PDIP-16 pin ( Reference JEDEC Registration MS-001) A3 Dim A A1 A2 A3 D E E1 L° eB A E A1 A2 E1 eB L D Millimeters Min. 0.380 3.169 2.915 18.632 Inches Max. 5.320 3.422 3.803 19.646 Min. 0.015 0.125 0.115 0.735 6.464 380.25 9.506 0.245 0 0.335 7.605BSC 6.210 0 8.492 Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 Max. 0.210 0.135 0.150 0.775 0.300BSC 17 0.255 15 0.375 www.anpec.com.tw APA7063 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) temperature Reference JEDEC Standard J-STD-020A APRIL 1999 Peak temperature 183°C Pre-heat temperature Time Classification Reflow Profiles Convection or IR/ Convection Average ramp-up rate(183°C to Peak) 3°C/second max. 120 seconds max Preheat temperature 125 ± 25°C) 60 – 150 seconds Temperature maintained above 183°C Time within 5°C of actual peak temperature 10 –20 seconds Peak temperature range 220 +5/-0°C or 235 +5/-0°C Ramp-down rate 6 °C /second max. 6 minutes max. Time 25°C to peak temperature VPR 10 °C /second max. 60 seconds 215-219°C or 235 +5/-0°C 10 °C /second max. Package Reflow Conditions pkg. thickness ≥ 2.5mm and all bgas Convection 220 +5/-0 °C VPR 215-219 °C IR/Convection 220 +5/-0 °C pkg. thickness < 2.5mm and pkg. volume ≥ 350 mm³ Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 18 pkg. thickness < 2.5mm and pkg. volume < 350mm³ Convection 235 +5/-0 °C VPR 235 +5/-0 °C IR/Convection 235 +5/-0 °C www.anpec.com.tw APA7063 Reliability test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245° C , 5 SEC 1000 Hrs Bias @ 125 ° C 168 Hrs, 100 % RH , 121 ° C -65° C ~ 150° C , 200 Cycles VHBM > 2KV, VMM > 200V 10ms , Itr > 100mA Carrier Tape & Reel Dimensions t D P Po E P1 Bo F W Ao D1 Ko T2 J C A B T1 Application SOP- 8 A B C J T1 T2 W P E 330 ± 1 62 +1.5 12.75+ 0.15 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1.75±0.1 F D D1 Po P1 Ao Bo Ko t 4.0 ± 0.1 2.0 ± 0.1 6.4 ± 0.1 5.2± 0. 1 2.1± 0.1 0.3±0.013 5.5± 1 1.55 +0.1 1.55+ 0.25 Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 19 www.anpec.com.tw APA7063 Cover Tape Dimensions Application SOP- 8 Carrier Width 12 Cover Tape Width 9.3 Devices Per Reel 2500 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 20 www.anpec.com.tw