C8051F314 25 MIPS, 8 kB Flash, 32-Pin Mixed-Signal MCU Analog Peripherals High-Speed 8051 µC Core - Two Comparators - Programmable hysteresis and response time Configurable to generate interrupts or reset Low current (0.4 µA) - POR/Brown-out Detector Memory - On-Chip Debug - On-chip debug circuitry facilitates full speed, non-intrusive in-system debug (no emulator required) Provides breakpoints, single stepping Inspect/modify memory and registers Superior performance to emulation systems using ICE-chips, target pods, and sockets - 1280 bytes data RAM 8 kB Flash; in-system programmable in 512-byte sectors (512 bytes are reserved) Digital Peripherals - Supply Voltage: 2.7 to 3.6 V - Pipelined instruction architecture; executes 70% of instructions in 1 or 2 system clocks Up to 25 MIPS throughput with 25 MHz system clock Expanded interrupt handler Typical Operating Current:7 mA at 25 MHz 15 µA at 32 kHz Typical Stop Mode Current: <0.1 µA - 29 port I/O; all are 5 V tolerant Hardware SMBus™ (I2C™ compatible), SPI™, and UART serial ports available concurrently Programmable 16-bit counter/timer array with five capture/compare modules, WDT 4 general-purpose 16-bit counter/timers Realtime clock mode using timer or PCA Clock Sources - Internal oscillator: 24.5 MHz, 2% accuracy supports UART operation External oscillator: Crystal, RC, C, or Clock (1 or 2 pin modes) Can switch between clock sources on-the-fly 32-Pin LQFP Temperature Range: –40 to +85 °C VDD Analog/Digital Power GND Port 0 Latch P 0 Port 1 Latch D r v UART C2D Debug HW Reset RST/C2CK POR XTAL1 XTAL2 External Oscillator Circuit 2% Internal Oscillator BrownOut 8 0 5 1 8 kB FLASH 256 Byte SRAM 1 kB XRAM System Clock C o SFR Bus r e C R O S S B A R Timer 0,1,2,3 / RTC PCA/ WDT SMBus SPI D r v Port 2 Latch Copyright © 2004 by Silicon Laboratories D r v P 2 P 3 Port 3 Latch Small Form Factor P 1 D r v CP0 + - CP1 + - P0.0/VREF P0.1 P0.2/XTAL1 P0.3/XTAL2 P0.4/TX P0.5/RX P0.6/CNVST P0.7 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 P3.0/C2D P3.1 P3.2 P3.3 P3.4 8.26.2004 C8051F314 25 MIPS, 8 kB Flash, 32-Pin Mixed-Signal MCU Selected Electrical Specifications (TA = –40 to +85 C°, VDD = 2.7 V unless otherwise specified) PARAMETER CONDITIONS GLOBAL CHARACTERISTICS Supply Voltage Supply Current Clock = 25 MHz Clock =1 MHz Clock = 32 kHz; VDD Monitor Disabled Supply Current Oscillator off; VDD Monitor Enabled (shutdown) Oscillator off; VDD Monitor Disabled Clock Frequency Range INTERNAL OSCILLATOR Frequency COMPARATORS Mode0 Response Time Mode0 Supply Current Mode1 Response Time Mode1 Supply Current Mode2 Response Time (CP+) – (CP-) = 100 mV Mode2 Supply Current Mode3 Response Time (CP+) – (CP-) = 100 mV Mode3 Supply Current MIN TYP 2.7 MAX UNITS 3.6 25 V mA mA µA µA µA MHz 25.0 MHz 7 0.5 15 10 <0.1 DC 24.0 24.5 0.10 7.6 0.18 3.2 0.32 1.3 1.0 0.40 µs µA µs µA µs µA µs µA C8051F310DK Development Kit Package Information D MIN NOM MAX (mm) (mm) (mm) D1 A - A1 0.05 E1 E 32 1 A2 A b Small Form Factor A1 e 1.60 - 0.15 A2 1.35 1.40 1.45 b PIN 1 IDENTIFIER - 0.30 0.37 0.45 D - 9.00 - D1 - 7.00 - e - 0.80 - E - 9.00 - E1 - 7.00 - Copyright © 2004 by Silicon Laboratories 8.26.2004 Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders