FRA801G THRU FRA807G 8.0 AMPS. Glass Passivated Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 8.0 Amperes TO-220A Features .185(4.70) .175(4.44) Low forward voltage drop High current capability High reliability High surge current capability .412(10.5) MAX .113(2.87) .103(2.62) .27(6.86) .23(5.84) .594(15.1) .587(14.9) Mechanical Data .055(1.40) .045(1.14) DIA .154(3.91) .148(3.74) PIN1 2 .16(4.06) .14(3.56) Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds .16”,(4.06mm) from case. Mounting position: Any Weight: 2.24 grams .56(14.22) .53(13.46) .11(2.79) .10(2.54) .037(0.94) .027(0.68) .025(0.64) .014(0.35) .205(5.20) .195(4.95) PIN 1 PIN 2 CASE Case Positive Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FRA FRA FRA Type Number FRA FRA FRA FRA 801G 802G 803G 804G 805G 806G 807G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Units V V V I(AV) 8.0 A IFSM 150 A Maximum Instantaneous Forward Voltage @ 8.0A VF Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ IR 1.3 5.0 100 V uA uA nS pF ℃/W ℃ Maximum Reverse Recovery Time ( Note 2 ) Typical Junction Capacitance ( Note 1 ) TJ=25℃ Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range Trr Cj RθJC TJ ,TSTG 150 250 60 3.0 -65 to +150 Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4..0 Volts D.C. 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 3. Thermal Resistance from Junction to Case, with Heatsink size 2” x 3” x 0.25” Al-Plate - 452 - 500 RATINGS AND CHARACTERISTIC CURVES (FRA801G THRU FRA807G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 400 10 200 6 4 2 0 0 50 100 150 o PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) 150 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 40 Tj=25oC Pulse Width=300 s 1% Duty Cycle 20 10 4 2 1 0.4 0.2 125 0.1 0.6 TJ=125 0C 100 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE. (V) 8.3ms Single Half Sine Wave JEDEC Method 75 FIG.6- TYPICAL REVERSE CHARACTERISTICS 50 100 25 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 120 CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 8 100 80 60 40 Tj=25 0C f=1.0MHz Vsig=50mVp-p 20 40 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm Tj=125 0C 10 2 1 0.4 0.1 0.5 1 5 10 50 100 500 1000 REVERSE VOLTAGE. (V) - 453 - Tj=25 0C 0.2 0.1 0 Tj=75 0C 4 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)