Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Multilayer Type) Data Sheet 1 Chip Inductor (Chip Coil) Power Inductor (Multilayer Type) LQM2MP_G0 Series (0806 Size) c Packaging 0.9±0.1 c Dimensions 0.5±0.2 Code Packaging Minimum Quantity L 180mm Embossed Tape 3000 B Bulk(Bag) 1000 1.6±0.15 2.0±0.15 (in mm) c Rated Value (p: packaging code) Part Number Inductance Rated Current DC Resistance Self Resonance Frequency (min.) LQM2MPNR47MG0p 0.47µH ±20% 1600mA 0.060ohm ±25% 100MHz LQM2MPNR47NG0p 0.47µH ±30% 1600mA 0.060ohm ±25% 100MHz LQM2MPN1R0NG0p 1.0µH ±30% 1400mA 0.085ohm ±25% 60MHz LQM2MPN1R5MG0p 1.5µH ±20% 1200mA 0.11ohm ±25% 50MHz LQM2MPN1R5NG0p 1.5µH ±30% 1200mA 0.11ohm ±25% 50MHz LQM2MPN2R2MG0p 2.2µH ±20% 1200mA 0.11ohm ±25% 40MHz LQM2MPN2R2NG0p 2.2µH ±30% 1200mA 0.11ohm ±25% 40MHz LQM2MPN3R3NG0p 3.3µH ±30% 1200mA 0.12ohm ±25% 30MHz LQM2MPN4R7MG0p 4.7µH ±20% 1100mA 0.14ohm ±25% 20MHz LQM2MPN4R7NG0p 4.7µH ±30% 1100mA 0.14ohm ±25% 20MHz Test Frequency: 1MHz Class of Magnetic Shield: Magnetic shield of ferrite c Inductance-Frequency Characteristics (Typ.) Operating Temperature Range: -55 to +125°C c Inductance-Current Characteristics (Typ.) 10 10 4.7μH 3.3μH 4.7μH 3.3μH Inductance (μH) Inductance (μH) 2.2μH 1.5μH 1 1.0μH 2.2μH 1.5μH 1 1.0μH 0.47μH 0.47μH 0.1 0.1 0.1 1 10 100 Frequency (MHz) 1 10 100 Current (mA) 1000 10000 Continued on the following page. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2012.11.8 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Multilayer Type) Data Sheet 2 Continued from the preceding page. c Temperature Rise Characteristics (Typ.) 40 3.3μH 4.7μH Temperature Rise (°C) 30 2.2μH 1.5μH 20 1.0μH 0.47μH 10 0 0 400 800 Current (mA) 1200 1600 c !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2012.11.8 http://www.murata.com/