HMC385LP4 v01.0604 MICROWAVE CORPORATION MMIC VCO w/ BUFFER AMPLIFIER, 2.25 - 2.5 GHz Typical Applications Features Low noise MMIC VCO w/Buffer Amplifier for: Pout: +4.5 dBm • Wireless Infrastructure Phase Noise: -115 dBc/Hz @100 KHz • Industrial Controls No External Resonator Needed • Test Equipment Single Supply: 3V @ 35 mA • Military QFN Leadless SMT Package, 16 mm2 Functional Diagram General Description The HMC385LP4 is a GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCO with integrated resonator, negative resistance device, varactor diode, and buffer amplifier. Covering 2.25 to 2.5 GHz, the VCO’s phase noise performance is excellent over temperature, shock, vibration and process due to the oscillator’s monolithic structure. Power output is 4.5 dBm typical from a single supply of 3V @ 35mA. The voltage controlled oscillator is packaged in a low cost leadless QFN 4 x 4 mm surface mount package. VCOs - SMT 15 Electrical Specifications, TA = +25° C, Vcc = +3V Parameter Min. Frequency Range Power Output 1.5 SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RF Output Tune Voltage (Vtune) Supply Current (Icc) (Vcc = +3.0V) Typ. GHz 4.5 dBm -115 dBc/Hz 0 10 35 V mA 10 µA 9 dB Harmonics 2nd 3rd -7 -23 dBc dBc Pulling (into a 2.0:1 VSWR) 2.0 MHz pp Pushing @ Vtune= +5V -2 MHz/V 0.25 MHz/°C Frequency Drift Rate 15 - 14 Units 2.25 - 2.5 Tune Port Leakage Current Output Return Loss Max. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC385LP4 v01.0604 MICROWAVE CORPORATION MMIC VCO w/ BUFFER AMPLIFIER, 2.25 - 2.5 GHz Frequency vs. Tuning Voltage, T= 25°C Frequency vs. Tuning Voltage, Vcc= +3V 2.6 OUTPUT FREQUENCY (GHz) 2.5 2.4 2.3 2.2 Vcc=2.75V Vcc=3.0V Vcc=3.25V 2.1 2 2.5 2.4 2.3 2.2 +25 C +85 C -40 C 2.1 2 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 TUNING VOLTAGE (VOLTS) Sensitivity vs. Tuning Voltage, Vcc= +3V 6 7 8 9 10 8 160 7 140 OUTPUT POWER (dBm) SENSITIVITY (MHz/VOLT) 5 Output Power vs. Tuning Voltage, Vcc= +3V 180 +25 C +85 C -40 C 120 100 80 60 40 6 15 5 4 3 2 +25 C +85 C -40 C 1 20 0 0 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 TUNING VOLTAGE (VOLTS) -90 -95 10 KHz Offset 100 KHz Offset -105 -110 -115 -120 1 2 3 4 5 6 7 TUNING VOLTAGE (VOLTS) 6 7 8 8 9 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 3 10 9 10 +25 C +85 C -40 C SSB PHASE NOISE (dBc/Hz) -85 0 5 Typical SSB Phase Noise @ Vtune= +5V -80 -100 4 TUNING VOLTAGE (VOLTS) Phase Noise vs. Tuning Voltage SSB PHASE NOISE (dBc/Hz) 4 TUNING VOLTAGE (VOLTS) 10 VCOs - SMT OUTPUT FREQUENCY (GHz) 2.6 4 10 5 10 6 10 7 10 OFFSET FREQUENCY (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 15 - 15 HMC385LP4 v01.0604 MICROWAVE CORPORATION MMIC VCO w/ BUFFER AMPLIFIER, 2.25 - 2.5 GHz Absolute Maximum Ratings Typical Supply Current vs. Vcc Vcc +3.5 Vdc Vcc (V) Icc (mA) Vtune 0 to +11V 2.75 28 Channel Temperature 135 °C 3.0 35 Continuous Pdiss (T = 85°C) (derate 6.28 mW/°C above 85°C) 3.25 41 565 W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Note: VCO will operate over full voltage range shown above. Outline Drawing VCOs - SMT 15 NOTES: 1. MATERIAL PACKAGE BODY: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY 3. LEAD AND GROUND PADDLE PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 6. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 7. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. 15 - 16 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC385LP4 v01.0604 MICROWAVE CORPORATION MMIC VCO w/ BUFFER AMPLIFIER, 2.25 - 2.5 GHz Pin Descriptions Function Description 1- 14, 17 - 19, 21, 23, 24 N/C No Connection 15 GND This pin must be connected to RF & DC ground. 16 RFOUT RF output (AC coupled) 20 Vcc Supply Voltage Vcc= 3V VTUNE Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. GND Package bottom has an exposed metal paddle that must be RF & DC grounded. 22 Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 15 VCOs - SMT Pin Number 15 - 17 v01.0604 MICROWAVE CORPORATION HMC385LP4 MMIC VCO w/ BUFFER AMPLIFIER, 2.25 - 2.5 GHz Evaluation PCB VCOs - SMT 15 15 - 18 List of Materials Item Description J1 - J2 PC Mount SMA RF Connector J3 - J4 DC Pin C1 4.7 µF Tantalum Capacitor C2 10,000 pF Capacitor, 0603 Pkg. U1 HMC385LP4 VCO PCB* 105667 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. * Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC385LP4 MMIC VCO w/ BUFFER AMPLIFIER, 2.25 - 2.5 GHz Notes: VCOs - SMT 15 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 15 - 19