MVIP, MVIL, and MVIV Series ¾ MIL-STD-883 Level B Screening Available ¾ Available to -55°C to + 125°C Operating ¾ RoHS Compliant ¾ Less than 1 pSec Jitter ELECTRICAL SPECIFICATIONS: LVDS Frequency Range Frequency Stability* Operating Temp.Range Storage Temp. Range Aging Logic “0” Logic “1” 1.43V typ 1.10V typ 50 mA max 60 mA max N/A +2.5VDC ± 5% +3.3VDC ± 5% +5.0VDC ± 5% Supply Voltage (Vdd) Supply Current Symmetry (50% of waveform) Rise / Fall Time (20% to 80%) Load Start Time Phase Jitter (12kHz to 20MHz) Tri-State Operation Vil LVPECL PECL 70.000MHz to 800.000MHZ (See Part Number Guide for Options) (See Part Number Guide for Options) -55°C to +125°C ±5 ppm / yr max Vdd – 1.620 VDC max Vdd – 1.620 VDC max Vdd- 1.025 vdc min Vdd- 1.025 vdc min 50 mA max N/A 60 mA max N/A N/A 140 mA max (See Part Number Guide for Options) 2nSec max 50 Ohms into Vdd-2.00 VDC 10mSec max Less than 1 pSec Vih = 70% of Vdd min to Enable Output = 30% max or grounded to Disable Output (High Impedance) * Inclusive of Temp., Load, Voltage and Aging +2.5VDC +3.3VDC +5.0VDC Control Voltage (Vc) 1.25VDC ±1.00VDC 1.65VDC ±1.50VDC N/A 1.25VDC ±1.00VDC 1.65VDC ±1.50VDC N/A (See Part Number Guide for Options) (See Part Number Guide for Options) Pullability Linearity N/A N/A 2.50VDC ±2.00VDC MECHANICAL DIMENSIONS: 7.20 [.283] MAX 2.00 [.079] MAX 2.54 [.100] 5.20 [.205] MAX 2.54 [.100] 4 5 6 3 2 1 2.54 [.100] 4.20 [.165] 2.40 [.094] 1.30 [.051] 2.00 [.079] 1.40 [.055] DIMENSIONS IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR RECOMMENDED 2.54 [.100] 1.80 [.071] PIN PIN PIN PIN PIN PIN 1 2 3 4 5 6 PIN CONNECTIONS VOLTAGE CONTROL ENABLE/DISABLE GROUND OUTPUT COMPLIMENTARY OUTPUT SUPPLY VOLTAGE RECOMMENDED LAND PATTERN PART NUMBER GUIDE: Frequency MVI Output P = PECL L = LVPECL V = LVDS Supply Voltage 2 = +2.5 VDC 3 = +3.3 VDC 5 = +5.0 VDC Frequency Stability 020 = ±20 ppm 025 = ±25 ppm 050 = ±50 ppm 100 = ±100 ppm Operating Temperature Blank = 0°C to +70°C 27 = -20°C to +70°C 48 = -40°C to +85°C 55 = -55°C to +125°C Symmetry * Blank = 40%/60% A = 45%/55% B = 47.5%/52.5% Pullability A = ±200 ppm min C = ±100 ppm min D = ±50 ppm min P = ±25 ppm min Linearity Blank = ±20% max X = ±5% max Y = ±10% max Z = ±15% max *Option B (47.5/52.5%) Available up to 500MHZ only Please Consult with MMD Sales Deparment for any other Parameters or Options MMD Components, 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Specifications subject to change without notice Revision MVIP032907B