Sample & Buy Product Folder Support & Community Tools & Software Technical Documents DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 DRV8824 Stepper Motor Controller IC 1 Features 3 Description • The DRV8824 provides an integrated motor driver solution for printers, scanners, and other automated equipment applications. The device has two H-bridge drivers and a microstepping indexer, and is intended to drive a bipolar stepper motor. The output driver block consists of N-channel power MOSFETs configured as full H-bridges to drive the motor windings. The DRV8824 is capable of driving up to 1.6 A of current from each output (with proper heatsinking, at 24 V and 25°C). 1 • • • • • • • • PWM Microstepping Stepper Motor Driver – Built-In Microstepping Indexer – Up to 1/32 Microstepping Multiple Decay Modes: – Mixed Decay – Slow Decay – Fast Decay 8.2-V to 45-V Operating Supply Voltage Range 1.6-A Maximum Drive Current at 24 V and TA = 25°C Simple STEP/DIR Interface Low-Current Sleep Mode Built-In 3.3-V Reference Output Small Package and Footprint Protection Features: – Overcurrent Protection (OCP) – Thermal Shutdown (TSD) – VM Undervoltage Lockout (UVLO) – Fault Condition Indication Pin (nFAULT) A simple STEP/DIR interface allows easy interfacing to controller circuits. Mode pins allow for configuration of the motor in full-step up to 1/32-step modes. Decay mode is configurable so that slow decay, fast decay, or mixed decay can be used. A low-power sleep mode is provided which shuts down internal circuitry to achieve very-low quiescent current draw. This sleep mode can be set using a dedicated nSLEEP pin. Internal shutdown functions are provided for overcurrent, short circuit, undervoltage lockout, and over temperature. Fault conditions are indicated through the nFAULT pin. Device Information(1) 2 Applications • • • • • • • • • PART NUMBER Automatic Teller Machines Money Handling Machines Video Security Cameras Printers Scanners Office Automation Machines Gaming Machines Factory Automation Robotics DRV8824 PACKAGE BODY SIZE (NOM) HTSSOP (28) 9.70 mm × 6.40 mm QFN (28) 5.00 mm × 5.00 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. 4 Simplified Schematic Microstepping Current Waveform DIR Decay Mode Step Size 1.6 A Stepper Motor Driver M ± Controller DRV8824 + STEP + nFAULT 1.6 A ± Current (% of Full Scale) 8.2 to 45 V Increasing Current Decreasing Current Increasing Current Decreasing Current 1/32 µstep Electrical Angle 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Simplified Schematic............................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 1 2 3 4 7.1 7.2 7.3 7.4 7.5 7.6 7.7 4 4 4 5 6 7 8 Absolute Maximum Ratings ...................................... Handling Ratings....................................................... Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Timing Requirements ................................................ Typical Characteristics .............................................. Detailed Description .............................................. 9 8.1 Overview ................................................................... 9 8.2 Functional Block Diagram ....................................... 10 8.3 Feature Description................................................. 11 8.4 Device Functional Modes........................................ 18 9 Application and Implementation ........................ 19 9.1 Application Information............................................ 19 9.2 Typical Application .................................................. 19 10 Power Supply Recommendations ..................... 22 10.1 Bulk Capacitance .................................................. 22 10.2 Power Supply and Logic Sequencing ................... 22 11 Layout................................................................... 23 11.1 Layout Guidelines ................................................. 23 11.2 Layout Example .................................................... 23 12 Device and Documentation Support ................. 24 12.1 Trademarks ........................................................... 24 12.2 Electrostatic Discharge Caution ............................ 24 12.3 Glossary ................................................................ 24 13 Mechanical, Packaging, and Orderable Information ........................................................... 24 5 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision H (December 2013) to Revision I Page • Updated data sheet to new TI standard: added sections and rearranged material .............................................................. 1 • Updated pin description for AVREF and BVREF .................................................................................................................. 3 • Added power supply ramp rate to Absolute Maximum Ratings ............................................................................................ 4 • Added minimum voltage for VIL and removed typical ............................................................................................................. 6 • Updated parameter descriptions in Timing Requirements and tWAKE minimum and maximum ............................................. 7 Changes from Revision G (August 2013) to Revision H • 2 Page Changed in Electrical Characteristics table, section DECAY INPUT third row ...................................................................... 6 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 6 Pin Configuration and Functions PWP PACKAGE (TOP VIEW) RHD PACKAGE (TOP VIEW) DECAY DIR nENBL STEP NC MODE0 MODE1 22 23 24 25 27 26 28 MODE2 nHOME GND CP1 CP2 VCP VMA 1 21 2 20 3 19 GND (PPAD) 4 18 5 17 6 16 7 15 nFAULT nSLEEP nRESET V3P3OUT GND BVREF AVREF 14 13 12 11 9 10 8 VMB BOUT1 ISENB BOUT2 AOUT2 ISENA AOUT2 Pin Functions PIN NAME PWP RHD I/O (1) DESCRIPTION EXTERNAL COMPONENTS OR CONNECTIONS POWER AND GROUND GND 14, 28 3, 17 — Device ground VMA 4 7 — Bridge A power supply VMB 11 14 — Bridge B power supply V3P3OUT 15 18 O 3.3-V regulator output CP1 1 4 IO Charge pump flying capacitor CP2 2 5 IO Charge pump flying capacitor VCP 3 6 IO High-side gate drive voltage Connect a 0.1-μF 16-V ceramic capacitor and a 1-MΩ resistor to VM. nENBL 21 24 I Enable input Logic high to disable device outputs and indexer operation, logic low to enable. Internal pulldown. nSLEEP 17 20 I Sleep mode input Logic high to enable device, logic low to enter low-power sleep mode. Internal pulldown. STEP 22 25 I Step input Rising edge causes the indexer to move one step. Internal pulldown. DIR 20 23 I Direction input Level sets the direction of stepping. Internal pulldown. MODE0 24 27 I Microstep mode 0 MODE1 25 28 I Microstep mode 1 MODE2 26 1 I Microstep mode 2 DECAY 19 22 I Decay mode Low = slow decay, Open = mixed decay, High = fast decay. Internal pulldown and pullup. nRESET 16 19 I Reset input Active-low reset input initializes the indexer logic and disables the Hbridge outputs. Internal pulldown. AVREF 12 15 I Bridge A current set reference input BVREF 13 16 I Bridge B current set reference input NC 23 26 — Connect to motor supply (8.2 to 45 V). Both pins must be connected to same supply, bypassed with a 0.1-µF capacitor to GND, and connected to appropriate bulk capacitance. Bypass to GND with a 0.47-μF 6.3-V ceramic capacitor. Can be used to supply VREF. Connect a 0.01-μF 50-V capacitor between CP1 and CP2. CONTROL (1) No connect MODE0 through MODE2 set the step mode: full, 1/2, 1/4, 1/8/ 1/16, or 1/32 step. Internal pulldown. Reference voltage for winding current set. Normally AVREF and BVREF are connected to the same voltage. Can be connected to V3P3OUT. Leave this pin unconnected. Directions: I = input, O = output, OD = open-drain output, IO = input/output Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 3 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com Pin Functions (continued) PIN NAME PWP RHD I/O (1) DESCRIPTION EXTERNAL COMPONENTS OR CONNECTIONS STATUS nHOME 27 2 OD Home position Logic low when at home state of step table nFAULT 18 21 OD Fault Logic low when in fault condition (overtemperature, overcurrent) OUTPUT ISENA 6 9 IO Bridge A ground / Isense Connect to current sense resistor for bridge A. ISENB 9 12 IO Bridge B ground / Isense Connect to current sense resistor for bridge B. AOUT1 5 8 O Bridge A output 1 AOUT2 7 10 O Bridge A output 2 Connect to bipolar stepper motor winding A. Positive current is AOUT1 → AOUT2 BOUT1 10 13 O Bridge B output 1 BOUT2 8 11 O Bridge B output 2 Connect to bipolar stepper motor winding B. Positive current is BOUT1 → BOUT2 7 Specifications 7.1 Absolute Maximum Ratings over operating free-air temperature (unless otherwise noted) VMx Power supply voltage VMx Power supply ramp rate VREF (1) (2) MIN MAX –0.3 47 V 1 V/µs Digital pin voltage –0.5 7 V Input voltage –0.3 4 V 0.8 V Internally limited A ISENSEx pin voltage (3) –0.8 Peak motor drive output current, t <1 μs Continuous motor drive output current (4) 1.6 Continuous total power dissipation TJ (1) (2) (3) (4) UNIT A See Thermal Information Operating virtual junction temperature range –40 150 °C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to network ground pin. Transients of ±1 V for less than 25 ns are acceptable. Power dissipation and thermal limits must be observed. 7.2 Handling Ratings Tstg Storage temperature range (1) V(ESD) (1) (2) Electrostatic Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins discharge Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (2) MIN MAX UNIT –60 150 °C –2000 2000 –500 500 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 7.3 Recommended Operating Conditions MIN VM Motor power supply voltage range VREF VREF input voltage (2) IV3P3 V3P3OUT load current (1) (2) 4 (1) NOM MAX 8.2 45 1 3.5 1 UNIT V V mA All VM pins must be connected to the same supply voltage. Operational at VREF between 0 and 1 V, but accuracy is degraded. Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 7.4 Thermal Information DRV8824 THERMAL METRIC PWP (28 PINS) RHD (28 PINS) RθJA Junction-to-ambient thermal resistance (1) 38.9 35.8 RθJC(top) Junction-to-case (top) thermal resistance (2) 23.3 25.1 21.2 8.2 0.8 0.3 20.9 8.2 2.6 1.1 (3) RθJB Junction-to-board thermal resistance ψJT Junction-to-top characterization parameter (4) ψJB Junction-to-board characterization parameter (5) RθJC(bot) (1) (2) (3) (4) (5) (6) Junction-to-case (bottom) thermal resistance (6) UNIT °C/W The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. Spacer Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 5 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com 7.5 Electrical Characteristics over operating free-air temperature range of –40°C to 85°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT POWER SUPPLIES IVM VM operating supply current VM = 24 V, fPWM < 50 kHz IVMQ VM sleep mode supply current VM = 24 V 5 8 mA 10 20 μA V3P3OUT REGULATOR V3P3 V3P3OUT voltage IOUT = 0 to 1 mA, VM = 24 V, TJ = 25°C 3.18 3.30 3.42 IOUT = 0 to 1 mA 3.10 3.30 3.50 V LOGIC-LEVEL INPUTS VIL Input low voltage 0 0.7 V VIH Input high voltage 2 5.25 V VHYS Input hysteresis IIL Input low current VIN = 0 IIH Input high current VIN = 3.3 V RPD Internal pulldown resistance 0.45 –20 nENBL, nRESET, DIR, STEP, MODEx nSLEEP V 20 μA 100 μA 100 kΩ 1 MΩ nHOME, nFAULT OUTPUTS (OPEN-DRAIN OUTPUTS) VOL Output low voltage IO = 5 mA IOH Output high leakage current VO = 3.3 V 0.5 V 1 μA 0.8 V DECAY INPUT VIL Input low threshold voltage For slow decay mode VIH Input high threshold voltage For fast decay mode IIN Input current RPU Internal pullup resistance RPD Internal pulldown resistance 2 V –100 100 µA 130 kΩ 80 kΩ H-BRIDGE FETS RDS(ON) HS FET on resistance RDS(ON) LS FET on resistance IOFF Off-state leakage current VM = 24 V, IO = 1 A, TJ = 25°C 0.63 VM = 24 V, IO = 1 A, TJ = 85°C 0.76 VM = 24 V, IO = 1 A, TJ = 25°C 0.65 VM = 24 V, IO = 1 A, TJ = 85°C 0.78 –20 0.90 0.90 20 Ω Ω μA MOTOR DRIVER ƒPWM Internal PWM frequency tBLANK Current sense blanking time 50 kHz tR Rise time VM = 24 V 100 360 ns tF Fall time VM = 24 V 80 250 ns tDEAD Dead time μs 3.75 400 ns PROTECTION CIRCUITS VUVLO VM undervoltage lockout voltage IOCP Overcurrent protection trip level tDEG Overcurrent deglitch time TTSD Thermal shutdown temperature VM rising 7.8 1.8 8.2 5 1.75 Die temperature 150 V A µs 160 180 °C 3 μA 660 685 mV CURRENT CONTROL IREF xVREF input current xVREF = 3.3 V VTRIP xISENSE trip voltage xVREF = 3.3 V, 100% current setting 6 Submit Documentation Feedback –3 635 Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 Electrical Characteristics (continued) over operating free-air temperature range of –40°C to 85°C (unless otherwise noted) PARAMETER ΔITRIP AISENSE Current trip accuracy (relative to programmed value) Current sense amplifier gain TEST CONDITIONS MIN TYP MAX xVREF = 3.3 V , 5% current setting –25% 25% xVREF = 3.3 V , 10% to 34% current setting –15% 15% xVREF = 3.3 V, 38% to 67% current setting –10% 10% xVREF = 3.3 V, 71% to 100% current setting –5% 5% Reference only 5 UNIT V/V 7.6 Timing Requirements MIN 1 ƒSTEP Step frequency 2 tWH(STEP) Pulse duration, STEP high 3 tWL(STEP) 4 tSU(STEP) 5 MAX UNIT 250 kHz 1.9 μs Pulse duration, STEP low 1.9 μs Setup time, command before STEP rising 200 ns tH(STEP) Hold time, command after STEP rising 200 ns 6 tENBL Enable time, nENBL active to STEP 200 ns 7 tWAKE Wakeup time, nSLEEP inactive high to STEP input accepted 1 ms Figure 1. Timing Diagram Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 7 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com 7.7 Typical Characteristics 7.0 14 13 6.5 12 IVMQ (A) IVM (mA) 6.0 5.5 5.0 11 10 9 -40°C 8 25°C 4.5 85°C 125°C 4.0 10 15 20 25 30 35 40 VM (V) 25°C 85°C 7 125°C 6 45 10 15 C001 -40°C 85°C 25°C 125°C 35 40 45 C002 10 V 24 V 1800 RDS(ON) HS + LS (m) RDS(ON) HS + LS (m) 30 Figure 3. IVMQ vs VM 2000 1800 1600 1400 1200 1000 45 V 1600 1400 1200 1000 800 800 10 15 20 25 30 35 VM (V) 40 45 ±50 C003 Figure 4. RDS(ON) vs VM 8 25 VM (V) Figure 2. IVM vs VM 2000 20 ±25 0 25 50 75 TA (C) 100 125 C004 Figure 5. RDS(ON) vs Temperature Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 8 Detailed Description 8.1 Overview The DRV8824 is an integrated motor driver solution for bipolar stepper motors. The device integrates two NMOS H-bridges, current sense, regulation circuitry, and a microstepping indexer. The DRV8824 can be powered with a supply voltage between 8.2 to 45 V and is capable of providing an output current up to 1.6 A full-scale. A simple STEP/DIR interface allows for easy interfacing to the controller circuit. The internal indexer is able to execute high-accuracy microstepping without requiring the processor to control the current level. The current regulation is highly configurable, with three decay modes of operation. Fast, slow, and mixed decay can be selected depending on the application requirements. A low-power sleep mode is included which allows the system to save power when not driving the motor. Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 9 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com 8.2 Functional Block Diagram VM 3.3 V LS Gate Drive V3P3OUT CP1 Internal VCC V3P3OUT Charge Pump Low Side Gate Drive CP2 HS Gate Drive VM VCP 3.3 V VM AVREF VM BVREF VMA + nENBL AOUT1 + STEP Stepper Motor Motor Driver A AOUT2 DIR ± + ± DECAY ISENA MODE0 MODE1 MODE2 Control Logic/ Indexer VM VMB nRESET BOUT1 Motor Driver B nSLEEP BOUT2 nHOME Thermal Shut Down nFAULT GND 10 PPAD ISENB GND Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 8.3 Feature Description 8.3.1 PWM Motor Drivers The DRV8824 contains two H-bridge motor drivers with current-control PWM circuitry. Figure 6 shows a block diagram of the motor control circuitry. Figure 6. Motor Control Circuitry Note that there are multiple VM motor power supply pins. All VM pins must be connected together to the motor supply voltage. Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 11 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com Feature Description (continued) 8.3.2 Current Regulation The current through the motor windings is regulated by a fixed-frequency PWM current regulation, or current chopping. When an H-bridge is enabled, current rises through the winding at a rate dependent on the DC voltage and inductance of the winding. After the current hits the current chopping threshold, the bridge disables the current until the beginning of the next PWM cycle. In stepping motors, current regulation is used to vary the current in the two windings in a semi-sinusoidal fashion to provide smooth motion. The PWM chopping current is set by a comparator which compares the voltage across a current sense resistor connected to the xISEN pins, multiplied by a factor of 5, with a reference voltage. The reference voltage is input from the xVREF pins. The full-scale (100%) chopping current is calculated in Equation 1. VREFX ICHOP = 5¾ · RISENSE (1) Example: If a 0.5-Ω sense resistor is used and the VREFx pin is 3.3 V, the full-scale (100%) chopping current will be 3.3 V / (5 × 0.5 Ω) = 1.32 A. The reference voltage is scaled by an internal DAC that allows fractional stepping of a bipolar stepper motor, as described in Microstepping Indexer. 8.3.3 Decay Mode During PWM current chopping, the H-bridge is enabled to drive current through the motor winding until the PWM current chopping threshold is reached. Figure 7 shows this as case 1. The current flow direction shown indicates positive current flow. After the chopping current threshold is reached, the H-bridge can operate in two different states, fast decay or slow decay. In fast decay mode, after the PWM chopping current level has been reached, the H-bridge reverses state to allow winding current to flow in a reverse direction. As the winding current approaches 0, the bridge is disabled to prevent any reverse current flow. Figure 7 shows fast decay mode as case 2. In slow decay mode, winding current is re-circulated by enabling both of the low-side FETs in the bridge. Figure 7 shows this as case 3. 12 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 Feature Description (continued) Figure 7. Decay Mode The DRV8824 supports fast decay, slow decay, and a mixed decay mode. Slow, fast, or mixed decay mode is selected by the state of the DECAY pin – logic low selects slow decay, open selects mixed decay operation, and logic high sets fast decay mode. The DECAY pin has both an internal pullup resistor of approximately 130 kΩ and an internal pulldown resistor of approximately 80 kΩ. This sets the mixed decay mode if the pin is left open or undriven. Mixed decay mode begins as fast decay, but at a fixed period of time (75% of the PWM cycle) switches to slow decay mode for the remainder of the fixed PWM period. This occurs only if the current through the winding is decreasing (per Table 2); if the current is increasing, then slow decay is used. 8.3.4 Blanking Time After the current is enabled in an H-bridge, the voltage on the xISEN pin is ignored for a fixed period of time before enabling the current sense circuitry. This blanking time is fixed at 3.75 μs. Note that the blanking time also sets the minimum on time of the PWM. 8.3.5 Microstepping Indexer Built-in indexer logic in the DRV8824 allows a number of different stepping configurations. The MODE0 through MODE2 pins are used to configure the stepping format, as shown in Table 1. Table 1. Stepping Format MODE2 MODE1 MODE0 0 0 0 Full step (2-phase excitation) with 71% current STEP MODE 0 0 1 1/2 step (1-2 phase excitation) 0 1 0 1/4 step (W1-2 phase excitation) 0 1 1 8 microsteps/step 1 0 0 16 microsteps/step 1 0 1 32 microsteps/step 1 1 0 32 microsteps/step 1 1 1 32 microsteps/step Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 13 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com Table 2 shows the relative current and step directions for different settings of MODEx. At each rising edge of the STEP input, the indexer travels to the next state in the table. The direction is shown with the DIR pin high; if the DIR pin is low, the sequence is reversed. Positive current is defined as xOUT1 = positive with respect to xOUT2. Note that if the step mode is changed while stepping, the indexer advances to the next valid state for the new MODEx setting at the rising edge of STEP. The home state is 45°. This state is entered at power-up or application of nRESET. This is shown in Table 2 by the shaded cells. The logic inputs DIR, STEP, nRESET, and MODEx have an internal pulldown resistors of 100 kΩ Table 2. Relative Current and Step Directions 1/32 STEP 1/16 STEP 1/8 STEP 1/4 STEP 1/2 STEP 1 1 1 1 1 FULL STEP WINDING CURRENT WINDING CURRENT 70% A B 100% 2 3 2 4 5 3 2 6 7 4 8 9 5 3 2 10 11 6 12 13 7 4 14 15 8 16 17 9 5 3 2 18 19 10 20 21 11 6 22 23 12 24 25 13 7 4 26 27 14 28 29 15 8 30 31 16 32 33 17 9 5 34 35 18 36 37 19 10 38 14 3 1 ELECTRICAL ANGLE 0% 0 100% 5% 3 100% 10% 6 99% 15% 8 98% 20% 11 97% 24% 14 96% 29% 17 94% 34% 20 92% 38% 23 90% 43% 25 88% 47% 28 86% 51% 31 83% 56% 34 80% 60% 37 77% 63% 39 74% 67% 42 71% 71% 45 67% 74% 48 63% 77% 51 60% 80% 53 56% 83% 56 51% 86% 59 47% 88% 62 43% 90% 65 38% 92% 68 34% 94% 70 29% 96% 73 24% 97% 76 20% 98% 79 15% 99% 82 10% 100% 84 5% 100% 87 0% 100% 90 –5% 100% 93 –10% 100% 96 –15% 99% 98 –20% 98% 101 –24% 97% 104 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 Table 2. Relative Current and Step Directions (continued) 1/32 STEP 1/16 STEP 39 20 1/8 STEP 1/4 STEP 1/2 STEP FULL STEP WINDING CURRENT WINDING CURRENT 70% A B 40 41 21 11 6 42 43 22 44 45 23 12 46 47 24 48 49 25 13 7 4 2 50 51 26 52 53 27 14 54 55 28 56 57 29 15 8 58 59 30 60 61 31 16 62 63 32 64 65 33 17 9 5 66 67 34 68 69 35 18 70 71 36 72 73 37 19 10 74 75 38 76 77 39 20 78 79 40 80 81 41 21 11 6 82 83 42 84 85 43 22 3 ELECTRICAL ANGLE –29% 96% 107 –34% 94% 110 –38% 92% 113 –43% 90% 115 –47% 88% 118 –51% 86% 121 –56% 83% 124 –60% 80% 127 –63% 77% 129 –67% 74% 132 –71% 71% 135 –74% 67% 138 –77% 63% 141 –80% 60% 143 –83% 56% 146 –86% 51% 149 –88% 47% 152 –90% 43% 155 –92% 38% 158 –94% 34% 160 –96% 29% 163 –97% 24% 166 –98% 20% 169 –99% 15% 172 –100% 10% 174 –100% 5% 177 –100% 0% 180 –100% –5% 183 –100% –10% 186 –99% –15% 188 –98% –20% 191 –97% –24% 194 –96% –29% 197 –94% –34% 200 –92% –38% 203 –90% –43% 205 –88% –47% 208 –86% –51% 211 –83% –56% 214 –80% –60% 217 –77% –63% 219 –74% –67% 222 –71% –71% 225 –67% –74% 228 –63% –77% 231 –60% –80% 233 –56% –83% 236 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 15 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com Table 2. Relative Current and Step Directions (continued) 1/32 STEP 1/16 STEP 1/8 STEP 1/4 STEP 1/2 STEP FULL STEP WINDING CURRENT WINDING CURRENT 70% A B 86 87 44 88 89 45 23 12 90 91 46 92 93 47 24 94 95 48 96 97 49 25 13 7 98 99 50 100 101 51 26 102 103 52 104 105 53 27 14 106 107 54 108 109 55 28 110 111 56 112 113 57 29 15 114 115 58 116 117 59 30 118 119 60 120 121 61 31 16 122 123 62 124 125 63 32 126 127 64 128 16 8 4 ELECTRICAL ANGLE –51% –86% 239 –47% –88% 242 –43% –90% 245 –38% –92% 248 –34% –94% 250 –29% –96% 253 –24% –97% 256 –20% –98% 259 –15% –99% 262 –10% –100% 264 –5% –100% 267 0% –100% 270 5% –100% 273 10% –100% 276 15% –99% 278 20% –98% 281 24% –97% 284 29% –96% 287 34% –94% 290 38% –92% 293 43% –90% 295 47% –88% 298 51% –86% 301 56% –83% 304 60% –80% 307 63% –77% 309 67% –74% 312 71% –71% 315 74% –67% 318 77% –63% 321 80% –60% 323 83% –56% 326 86% –51% 329 88% –47% 332 90% –43% 335 92% –38% 338 94% –34% 340 96% –29% 343 97% –24% 346 98% –20% 349 99% –15% 352 100% –10% 354 100% –5% 357 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 8.3.6 nRESET, nENBLE and nSLEEP Operation The nRESET pin, when driven active low, resets internal logic, and resets the step table to the home position. It also disables the H-bridge drivers. The STEP input is ignored while nRESET is active. The nENBL pin is used to control the output drivers and enable or disable operation of the indexer. When nENBL is low, the output H-bridges are enabled, and rising edges on the STEP pin are recognized. When nENBL is high, the H-bridges are disabled, the outputs are in a high-impedance state, and the STEP input is ignored. Driving nSLEEP low puts the device into a low-power sleep state. In this state, the H-bridges are disabled, the gate drive charge pump is stopped, the V3P3OUT regulator is disabled, and all internal clocks are stopped. In this state, all inputs are ignored until nSLEEP returns high. When returning from sleep mode, some time (approximately 1 ms) needs to pass before applying a STEP input, to allow the internal circuitry to stabilize. The nRESET and nENABLE pins have internal pulldown resistors of 100 kΩ. The nSLEEP pin has an internal pulldown resistor of 1 MΩ. 8.3.7 Protection Circuits The DRV8824 is fully protected against undervoltage, overcurrent, and overtemperature events. 8.3.7.1 Overcurrent Protection (OCP) An analog current limit circuit on each FET limits the current through the FET by removing the gate drive. If this analog current limit persists for longer than the OCP time, all FETs in the H-bridge will be disabled and the nFAULT pin will be driven low. The device remains disabled until either nRESET pin is applied, or VM is removed and re-applied. Overcurrent conditions on both high and low side devices, that is, a short to ground, supply, or across the motor winding, all result in an overcurrent shutdown. Note that overcurrent protection does not use the current sense circuitry used for PWM current control, and is independent of the ISENSE resistor value or VREF voltage. 8.3.7.2 Thermal Shutdown (TSD) If the die temperature exceeds safe limits, all FETs in the H-bridge will be disabled and the nFAULT pin will be driven low. After the die temperature has fallen to a safe level, operation automatically resumes. 8.3.7.3 Undervoltage Lockout (UVLO) If at any time the voltage on the VM pins falls below the UVLO threshold voltage, all circuitry in the device will be disabled and internal logic will be reset. Operation resumes when VM rises above the UVLO threshold. 8.3.8 Thermal Information 8.3.8.1 Thermal Protection The DRV8824 has TSD, as described in Thermal Shutdown (TSD). If the die temperature exceeds approximately 150°C, the device is disabled until the temperature drops to a safe level. Any tendency of the device to enter TSD is an indication of either excessive power dissipation, insufficient heatsinking, or too high an ambient temperature. 8.3.8.2 Power Dissipation Power dissipation in the DRV8824 is dominated by the power dissipated in the output FET resistance, or RDS(ON). Average power dissipation when running a stepper motor can be roughly estimated by Equation 2. PTOT = 4 · RDS(ON) · (IOUT(RMS)) 2 where • • • PTOT is the total power dissipation RDS(ON) is the resistance of each FET IOUT(RMS) is the RMS output current being applied to each winding (2) Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 17 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com IOUT(RMS) is equal to the approximately 0.7× the full-scale output current setting. The factor of 4 comes from the fact that there are two motor windings, and at any instant two FETs are conducting winding current for each winding (one high-side and one low-side). The maximum amount of power that can be dissipated in the device is dependent on ambient temperature and heatsinking. Note that RDS(ON) increases with temperature, so as the device heats, the power dissipation increases. This must be taken into consideration when sizing the heatsink. 8.3.8.3 Heatsinking The PowerPAD™ package uses an exposed pad to remove heat from the device. For proper operation, this pad must be thermally connected to copper on the PCB to dissipate heat. On a multi-layer PCB with a ground plane, this can be accomplished by adding a number of vias to connect the thermal pad to the ground plane. On PCBs without internal planes, copper area can be added on either side of the PCB to dissipate heat. If the copper area is on the opposite side of the PCB from the device, thermal vias are used to transfer the heat between top and bottom layers. For details about how to design the PCB, refer to TI application report SLMA002, PowerPAD™ Thermally Enhanced Package and TI application brief SLMA004, PowerPAD™ Made Easy, available at www.ti.com. In general, the more copper area that can be provided, the more power can be dissipated. It can be seen that the heatsink effectiveness increases rapidly to about 20 cm2, then levels off somewhat for larger areas. 8.4 Device Functional Modes 8.4.1 STEP/DIR Interface The STEP/DIR interface provides a simple method for advancing through the indexer table. For each rising edge on the STEP pin, the indexer travels to the next state in the table. The direction it moves in the table is determined by the input to the DIR pin. The signals applied to the STEP and DIR pins should not violate the timing diagram specified in Figure 1. 8.4.2 Microstepping The microstepping indexer allows for a variety of stepping configurations. The state of the indexer is determined by the configuration of the three MODE pins (refer to Table 1 for configuration options). The DRV8824 supports full step up to 1/32 microstepping. 18 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 9 Application and Implementation 9.1 Application Information The DRV8824 is used in bipolar stepper control. The microstepping motor driver provides additional precision and a smooth rotation from the stepper motor. The following design is a common application of the DRV8824. 9.2 Typical Application DRV8824 V3P3OUT CP1 GND CP2 nHOME VCP MODE2 VMA MODE1 AOUT1 MODE0 10 k 0.01 µF 1M 0.1 µF + 0.1 µF 400 m NC ISENA Stepper Motor ± VM 100 µF + + AOUT2 STEP BOUT2 nENBL ± 400 m DIR ISENB V3P3OUT BOUT1 DECAY VMB nFAULT AVREF nSLEEP BVREF nRESET 10 k V3P3OUT 10 k 30 k GND PPAD 0.1 µF V3P3OUT V3P3OUT 0.47 µF 9.2.1 Design Requirements Table 3 gives design input parameters for system design. Table 3. Design Parameters Design Parameter Reference Example Value Supply voltage VM 24 V Motor winding resistance RL 1.0 Ω/phase LL 3.5 mH/phase Motor winding inductance Motor full step angle Target microstepping level Target motor speed Target full-scale current θstep 1.8°/step nm 8 microsteps per step v 120 rpm IFS 1.25 A Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 19 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com 9.2.2 Detailed Design Procedure 9.2.2.1 Stepper Motor Speed The first step in configuring the DRV8824 requires the desired motor speed and microstepping level. If the target application requires a constant speed, then a square wave with frequency ƒstep must be applied to the STEP pin. If the target motor speed is too high, the motor will not spin. Make sure that the motor can support the target speed. For a desired motor speed (v), microstepping level (nm), and motor full step angle (θstep), fstep(steps/second) = v(rpm) · nm(steps) · 6 ¾ qstep(°/step) (3) θstep can be found in the stepper motor datasheet or written on the motor itself. For the DRV8824, the microstepping level is set by the USM pins and can be any of the settings in Table 1. Higher microstepping will mean a smoother motor motion and less audible noise, but will increase switching losses and require a higher ƒstep to achieve the same motor speed. 9.2.2.2 Current Regulation In a stepper motor, the full-scale current (IFS) is the maximum current driven through either winding. This quantity will depend on the VREF analog voltage and the sense resistor value (RSENSE). During stepping, IFS defines the current chopping threshold (ITRIP) for the maximum current step. VREF(V) VREF(V) ¾ IFS(A) = ¾ Av · RSENSE(W) = 5 · RSENSE(W) (4) IFS is set by a comparator which compares the voltage across RSENSE to a reference voltage. There is a current sense amplifier built in with programmable gain through ISGAIN. Note that IFS must also follow Equation 5 in order to avoid saturating the motor. VM is the motor supply voltage and RL is the motor winding resistance. IFS(A) < VM(V) ¾ · RL(W) + 2 RDS(ON)(W) + RSENSE(W) (5) 9.2.2.3 Decay Modes The DRV8824 supports three different decay modes: slow decay, fast decay, and mixed decay. The current through the motor windings is regulated using a fixed-frequency PWM scheme. This means that after any drive phase, when a motor winding current has hit the current chopping threshold (ITRIP), the DRV8824 will place the winding in one of the three decay modes until the PWM cycle has expired. Afterward, a new drive phase starts. The blanking time tBLANK defines the minimum drive time for the current chopping. ITRIP is ignored during tBLANK, so the winding current may overshoot the trip level. 20 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 9.2.3 Application Curves Figure 8. Microstepping Waveform, Phase A, Mixed Decay Figure 9. Microstepping Waveform, Slow Decay on Increasing Steps Figure 10. Microstepping Waveform, Mixed Decay on Decreasing Steps Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 21 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com 10 Power Supply Recommendations The DRV8824 is designed to operate from an input voltage supply (VM) range between 8.2 and 45 V. Two 0.01µF ceramic capacitors rated for VM must be placed as close as possible to the VMA and VMB pins respectively (one on each pin). In addition to the local decoupling caps, additional bulk capacitance is required and must be sized accordingly to the application requirements. 10.1 Bulk Capacitance Local bulk capacitance sizing is a critical factor in proper motor drive system design. It is dependent on a variety of factors including the type of power supply, inductance in the power supply wiring, type of motor, load demands/dumps of the motor, acceptable voltage ripple, and various other factors. Although power supplies often contain large amounts of bulk capacitance, this is often separated from the local motor drive system by parasitic inductance in the power supply wiring. The parasitic inductance will limit the rate current can change from the power supply and force the system to demand or dump current from or to another source with a lower inductance path. This source is often the local bulk capacitance located near the motor drive system. The magnitude and rate of the motor current demand or dump and acceptable voltage ripple will determine how large this bulk capacitance needs to be. The data sheet provides a recommended bulk capacitance value, but system-level testing is required to determine the appropriate sized capacitor for specific applications. A smaller filter capacitor (optional) may also be added to remove higher frequency noise from the power supply lines that may pass the bulk capacitance. External Power Supply Parasitic Wire Inductance Motor Drive System VM + ± Motor Driver GND Power Supply Bulk Capacitor Local Bulk Cap Local Filter Cap Figure 11. Example Setup of Motor Drive System With External Power Supply 10.2 Power Supply and Logic Sequencing There is no specific sequence for powering-up the DRV8824. It is okay for digital input signals to be present before VM is applied. After VM is applied to the DRV8824, it begins operation based on the status of the control pins. 22 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 DRV8824 www.ti.com SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 11 Layout 11.1 Layout Guidelines The VMA and VMB terminals should be bypassed to GND using low-ESR ceramic bypass capacitors with a recommended value of 0.01 µF rated for VM. This capacitor should be placed as close to the VMA and VMB pins as possible with a thick trace or ground plane connection to the device GND pin. The VMA and VMB pins must be bypassed to ground using a bulk capacitor. This component may be an electrolytic. If VMA and VMB are connected to the same board net, a single bulk capacitor is sufficient. A low-ESR ceramic capacitor must be placed in between the CPL and CPH pins. TI recommends a value of 0.01 µF rated for VMA and VMB. Place this component as close to the pins as possible. A low-ESR ceramic capacitor must be placed in between the VMA and VCP pins. TI recommends a value of 0.1 µF rated for 16 V. Place this component as close to the pins as possible. Also, place a 1-MΩ resistor between VCP and VMA. Bypass V3P3 to ground with a ceramic capacitor rated 6.3 V. Place this bypassing capacitor as close to the pin as possible. 11.2 Layout Example 0.1 µF CP1 GND CP2 nHOME 0.01 µF 1 M VCP MODE2 VMA MODE1 AOUT1 MODE0 0.1 µF RISENA RISENB ISENA NC AOUT2 STEP BOUT2 nEMBL ISENB DIR BOUT1 DECAY VMB nFAULT AVREF nSLEEP + 0.1 µF BVREF nRESET GND V3P3OUT 0.47 µF Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 23 DRV8824 SLVSA06I – OCTOBER 2009 – REVISED JUNE 2014 www.ti.com 12 Device and Documentation Support 12.1 Trademarks PowerPAD is a trademark of Texas Instruments. 12.2 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.3 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 24 Submit Documentation Feedback Copyright © 2009–2014, Texas Instruments Incorporated Product Folder Links: DRV8824 PACKAGE OPTION ADDENDUM www.ti.com 7-Apr-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) DRV8824PWP ACTIVE HTSSOP PWP 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 DRV8824 DRV8824PWPR ACTIVE HTSSOP PWP 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 DRV8824 DRV8824RHDR ACTIVE VQFN RHD 28 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 DRV8824 DRV8824RHDT ACTIVE VQFN RHD 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 DRV8824 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 7-Apr-2014 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 7-Apr-2014 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DRV8824PWPR HTSSOP PWP 28 2000 330.0 16.4 6.9 10.2 1.8 12.0 16.0 Q1 DRV8824RHDR VQFN RHD 28 3000 330.0 DRV8824RHDT VQFN RHD 28 250 180.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 12.4 5.3 5.3 1.5 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 7-Apr-2014 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DRV8824PWPR HTSSOP PWP 28 2000 367.0 367.0 38.0 DRV8824RHDR VQFN RHD 28 3000 367.0 367.0 35.0 DRV8824RHDT VQFN RHD 28 250 552.0 154.0 36.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DRV8824EVM