Document 661-1 Coupled Inductors LPD3015 For Flyback, SEPIC, Zeta and other Applications • Only 1.4 mm high and 3 mm square • Ideal for use in flyback, multi-output buck, SEPIC and Zeta applications. • High inductance, high efficiency and excellent current handling • Can also be used as two single inductors connected in series or parallel or as a common mode choke. + + D L1 C L2 VOUT C VIN – SW – Typical Flyback Converter D L2 + VOUT C AUX – + 0.118 ±0.003 3,00 ±0,076 Dot indicates pin 1 1 + VIN L1 D SW VOUT C – 4 – Typical Buck Converter with auxiliary output 0.118 ±0.003 3,00 ±0,076 XXX X 2 Dash number L1 Internal code VIN 1 4 0.022 0,54 0.094 0.040 2,30 1,02 *Height dimension is without optional solder applied. Maximum height with solder applied is 0.061 inches / 1,56 mm. 1 0.040 1,02 0.094 2,30 0.130 3,30 4 Dimensions are in 2 L2 45° typ 0.130 3,30 3 2 0.039 0,99 C + C1 L2 Q – 0.055 ±0.004 * 1,4 ±0,1 L1 D + 3 C – Typical SEPIC schematic + + – L2 C1 Q VIN VOUT L1 C D Typical Zeta schematic C VOUT – inches mm 3 [email protected] subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 661-1 Document 661-1 Revised 09/13/11 Revised 03/31/11 © © Coilcraft Coilcraft Inc. Inc. 2013 2013 This This product product may may not not be be used used in in medical medical or or high high risk risk applications applications without without prior prior Coilcraft Coilcraft approval. approval. Specification Specification subject subject to to change change without without notice. notice. Please Please check check web web site site for for latest latest information. information. Document 661-2 Coupled Inductors for SEPIC - LPD3015 Series Coupling Leakage Inductance2 DCR max3 SRF typ4 coefficient L typ5 1 Part number ±20% (µH) (Ohms) (MHz) typ (µH) LPD3015-391ML_ LPD3015-561ML_ LPD3015-102ML_ LPD3015-152ML_ LPD3015-182ML_ 0.39 0.56 1.0 1.5 1.8 10% drop Isat (A)6 Irms (A) 20% 30% both one drop drop windings7 winding8 0.071 0.079 0.129 0.204 0.273 289 235 160 140 135 0.89 0.93 0.95 0.96 0.96 0.08 0.08 0.09 0.11 0.13 3.2 2.7 2.0 1.6 1.5 3.3 2.8 2.1 1.7 1.6 3.4 2.8 2.2 1.8 1.6 1.45 1.37 1.08 0.86 0.78 2.05 1.94 1.52 1.20 1.10 LPD3015-222ML_ LPD3015-332ML_ LPD3015-472ML_ LPD3015-682ML_ LPD3015-103ML_ 2.2 3.3 4.7 6.8 10 0.300 0.337 0.503 0.622 1.040 110 90 79 58 48 0.97 0.98 0.98 0.98 0.99 0.14 0.16 0.18 0.22 0.28 1.5 1.0 0.86 0.77 0.58 1.6 1.1 0.87 0.78 0.59 1.6 1.2 0.88 0.79 0.60 0.75 0.67 0.54 0.49 0.38 1.05 0.94 0.76 0.69 0.53 LPD3015-153ML_ LPD3015-183ML_ LPD3015-223ML_ LPD3015-333ML_ LPD3015-473ML_ 15 18 22 33 47 1.420 1.550 1.89 2.84 4.03 35 33 30 23 17 0.99 0.99 0.99 0.99 0.99 0.37 0.42 0.48 0.63 0.81 0.49 0.46 0.42 0.34 0.28 0.50 0.47 0.43 0.35 0.29 0.51 0.48 0.44 0.36 0.30 0.32 0.31 0.28 0.23 0.19 0.46 0.44 0.40 0.32 0.27 LPD3015-683ML_ LPD3015-104ML_ LPD3015-124ML_ LPD3015-154ML_ LPD3015-184ML_ 68 100 120 150 180 6.11 8.54 9.23 12.40 15.32 14 11 9.0 8.0 7.5 0.99 0.99 0.99 0.99 0.99 1.13 1.50 1.76 2.22 2.79 0.24 0.20 0.19 0.16 0.15 0.25 0.21 0.20 0.17 0.16 0.26 0.22 0.20 0.18 0.17 0.16 0.13 0.13 0.11 0.10 0.22 0.19 0.18 0.16 0.14 LPD3015-224ML_ LPD3015-334ML_ 220 330 18.56 27.70 6.0 5.0 0.99 0.99 3.56 5.18 0.13 0.11 0.14 0.12 0.15 0.12 0.09 0.07 0.13 0.10 1. Please specify termination and packaging codes: Coupled Inductor Core and Winding Loss Calculator LPD3015-334MLC Termination: L = RoHS compliant Silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value. 3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. 4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value. 5. Leakage Inductance is for L1 and is measured with L2 shorted. 6. DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings. 7. Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. 8 Maximum current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. 9. Electrical specifications at 25°C. Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.” Refer to Doc 362 “Soldering Surface Mount Components” before soldering. This web-based utility allows you to enter frequency, peak-to-peak (ripple) current, and Irms current to predict temperature rise and overall losses, including core loss. Go to online calculator. Core material Ferrite Core and winding loss Go to online calculator Weight 45 – 52 mg Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Winding to winding isolation 100 Vrms Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.26 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. [email protected] subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 661-2 Revised 09/13/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 661-3 Coupled Inductors for SEPIC - LPD3015 Series Typical L vs Current Typical L vs Frequency 1000 1000 330 µH 330 µH 220 µH 220 µH 100 100 µH Inductance (µH) Inductance (µH) 100 33 µH 22 µH 10 10 µH 3.3 µH 2.2 µH 1 100 µH 33 µH 22 µH 10 10 µH 3.3 µH 2.2 µH 1 1.0 µH 1.0 µH 0.1 0.1 0.01 0.1 Current (A) 1 10 0.01 0.1 1 10 Document 661-3 Revised 09/13/11 Frequency (MHz) Typical Current Derating 100 90 80 70 60 50 40 30 20 10 0 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) [email protected] subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.