!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr)/ Ceramic Discriminators for Communications Equipment Cat.No.P05E-16 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. EU RoHS Compliant s s s All the products in this catalog comply with EU RoHS. EU RoHS is "the European Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment." For more details, please refer to our website 'Murata's Approach for EU RoHS' (http://www.murata.com/info/rohs.html). P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. CONTENTS P05E.pdf Nov.24,2011 1 CERAFILr and "CERAFIL" in this catalog are the trademarks of Murata Manufacturing Co., Ltd. 2 Part Numbering 2 Products Guide 4 1 CERAFILr kHz SMD Type SFPKA Series 5 2 CERAFILr kHz SMD Type CFUKG Series 7 3 CERAFILr kHz SMD Type CFUKG_X Series 9 4 CERAFILr kHz SMD Type CFUKF Series 11 5 CERAFILr kHz SMD Type CFWKA Series 13 6 CERAFILr kHz SMD Type CFWKA_Y Series 15 kHz SMD Type CERAFILr Notice 17 7 CERAFILr MHz SMD Type SFECF10M7 Series 21 8 CERAFILr MHz SMD Type SFSCE10M7 Series 23 MHz SMD Type CERAFILr Notice 25 SMD Type CERAFILr Standard Land Pattern Dimensions 31 kHz SMD Type CERAFILr Packaging 32 MHz SMD Type CERAFILr Packaging 34 9 CERAFILr Plastic Case General Use CFULA Series 35 10 CERAFILr Plastic Case General Use CFWLA Series 37 11 CERAFILr Plastic Case Miniaturized Type CFULB Series 39 12 CERAFILr Plastic Case Miniaturized Type CFWLB Series 41 13 CERAFILr Plastic Case Group Delay Flat Type CFULA_Y Series 43 14 CERAFILr Plastic Case Group Delay Flat Type CFWLA_Y Series 45 15 CERAFILr Plastic Case Group Delay Flat Type Miniaturized Type CFULB_Y Series 47 16 CERAFILr Plastic Case Group Delay Flat Type CFWLB_Y Series 49 Plastic Case Type CERAFILr Minimum Quantity/Notice 51 17 kHz Type Ceramic Discriminators 52 18 MHz Type Ceramic Discriminators 65 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Ceramic Discriminators Notice 70 Ceramic Discriminators Standard Land Pattern Dimensions/Packaging 74 18 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. o Part Numbering Ceramic Filters (CERAFILr) for IF (Part Number) SF P KA 455K SF E CF 10M7 DF00 q w e r -R0 D4A t S0 -R0 y u qProduct ID wOscillating/Element tProduct Specification Product ID CF Ceramic Filters Oscillating/Element U 4 Elements Area Expansion mode W 6 Elements Area Expansion mode P 4 Elements Area Expansion mode D4A Three-digit alphanumerics express pass bandwidth, center frequency tolerance and design type. SFE/S/J series are expressed by four-digit alphanumerics. E 2 Elements Thickness Expansion mode SF S 2 Elements Thickness Shear mode eStructure/Size Code Structure/Size Cp/Kp Chip Type Lp Lead Type p is "A" or subsequent code, which indicates the size. It varies depending on vibration mode and number of elements. Chip type is only applied for SF series. rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is hertz (Hz). If the unit is "kHz", it is expressed by three figures plus "K." If the unit is "MHz", a decimal point is expressed by the capital letter "M." 2 Product Specification Code yIndividual Specification Code Individual Specification Code 001 Expressed by three-digit alphanumerics. SFE/S/J series are expressed by two-digit alphanumerics. With standard type, y is omitted. uPackaging Code Packaging -B0 Bulk -R0 Embossed Taping ø=180mm -R1 Embossed Taping ø=330mm Embossed taping is applied to chip type. P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Discriminators for IF (kHz) (Part Number) CD B LB 450K q w e r C X A 16 t y u i -B0 o qProduct ID yApplication Product ID Code CD Ceramic Discriminators Application A Standard L Application with coil wOscillating uElement Type Code Oscillating B Area Expansion mode eStructure/Size Code Structure/Size Cp/Kp Chip Type Lp Lead Type Code Element Type X Low-capacitance Y High-capacitance iIC p is "A" or subsequent code, which indicates the size. It varies depending on vibration mode and number of elements. Code IC 16 Applicable IC Control code oPackaging rNominal Center Frequency Code Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Capital letter "K" following three figures expresses the unit of "kHz." tDetection Packaging -B0 Bulk -R0 Embossed Taping ø=180mm -R1 Embossed Taping ø=330mm Embossed taping is applied to chip type. With non-standard products, one letter indicating "Individual Specification" is added between "iApplicable IC" and "oPackage Specification code." Code Detection C Quadrature Detection Ceramic Discriminators for IF (MHz) (Part Number) CD S CB 10M7 GF 001 -R0 q w e t y r u qProduct ID tProduct Specification Product ID CD Discriminators Code Product Specification GF Two-digit alphanumerics express type, center frequency, rank, others wOscillation Code Oscillation S Thickness Shear mode yIC Code IC 001 Applicable IC Control Code eStructure/Size Code Structure/Size Cp Chip Type p is expressed "A" or subsequent code, which indicates the size. rNominal Center Frequency uPackaging Code Packaging -R0 Embossed Taping ø=180mm With non-standard products, an alphanumerics indicating "Individual Specification" is added between "yIC" and "uPackaging." Expressed by four-digit alphanumerics. The unit is in hertz (MHz). Decimal point is expressed by capital letter "M." 3 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Products Guide oSMD Type (kHz) Applications General Use Type Attenuation (dB) min. 6dB Bandwidth (kHz) min. Series A B C D ±17.5 ±15 ±12.5 ±10 E F G H J K L ±7.5 ±6 ±4.5 ±3 ±2 ±1.5 ±1 Within 455±80 or ±100kHz SFPKA455KM (4 Elements) – – – o o o o o – – – 27 (G to H; 25) CFUKG455KM (4 Elements) – – – o o o o – – – – 27 (G; 25) Narrow Bandwidth GDT Flat Type Miniature Series (Plastic Case Type) CFUKG455KMX (4 Elements) – – – – o o o o – – – 27 (G to H; 25) GDT Flat Type Miniature Series (Plastic Case Type) CFUKF455KM (4 Elements) o o o o o – – – – – – 25 (D to E; 23) GDT Flat Type High Selectivity SMD Series (Plastic Case Type) CFWKA450KBFY (6 Elements) – o – – – – – – – – – 45 High Selectivity SMD Series (Plastic Case Type) CFWKA450KM (6 Elements) – – – o o o o – – – – 50 High Selectivity Series (Plastic Case Type) oLead Type (kHz) Applications General Use Type Attenuation (dB) min. 6dB Bandwidth (kHz) min. Series A B C D ±17.5 ±15 ±12.5 ±10 E F G H J K L ±7.5 ±6 ±4.5 ±3 ±2 ±1.5 ±1 Within 455±80 or ±100kHz (G; 25) High Selectivity Low Profile Series CFWLA455KM (6 Elements) – o o o o o o o – – – 27 (H; 35) – o o o o o o o o – – 35 (H, J; 60) High Selectivity Miniature Series CFULB455KM (4 Elements) – o o o o o o o o – – 27 (H, J; 35) CFWLB455KM (6 Elements) – o o o o o o o o – – 35 (H, J; 55) GDT Flat Type Series CFULA455KMY (4 Elements) – o o o o o o – – – – 25 (D to G; 23) CFWLA455KMY (6 Elements) o o o o o o o – – – – 40 GDT Flat Type Miniature Series CFULB455KMY (4 Elements) – o o o o o o – – – – 25 (D to G; 23) CFWLB455KMY (6 Elements) o o o o o o o – – – – 40 (F; 35) CFULA455KM (4 Elements) 4 (G; 25) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment 1 CERAFILr kHz SMD Type SFPKA Series 7.5±0.3 8.4 max. 7.0±0.3 3.0±0.3 The SFPKA series is comprised of small, high-performance, economical, thin (5.0mm) filters consisting of 4 ceramic elements. Their innovative construction is perfect for shrinking mobile communication products such as cordless phones, pagers and transceivers. MARKING EIAJ CODE 5.0 max. 0.9±0.1 c Features 2.0±0.3 1.5±0.3 1. The filters are mountable by automatic placers. 2. The filters can be reflow soldered and withstand washing. 3. They are slim, at only 5.0mm maximum thickness. 4. The bandwidth ranges from D to H. 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) 1.5±0.3 2.0±0.3 1.6±0.3 Connection (1): Input (2): Ground (3): Output (1) (2) (3) (in mm) Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) Stop Band Attenuation (dB) Insertion Loss (dB) Ripple (dB) Input/Output Impedance (ohm) SFPKA455KD4A-R1 455 ±1.5kHz fn±10.0 min. fn±20.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 2.0 max. [within fn±7kHz] 1500 SFPKA455KE4A-R1 455 ±1.5kHz fn±7.5 min. fn±15.0 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±5kHz] 1500 SFPKA455KF4A-R1 455 ±1.5kHz fn±6.0 min. fn±12.5 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±4kHz] 1500 SFPKA455KG1A-R1 455 ±1.0kHz fn±4.5 min. fn±10.0 max. [within 40dB] 25 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±3kHz] 1500 SFPKA455KH1A-R1 455 ±1.0kHz fn±3.0 min. fn±9.0 max. [within 40dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±2kHz] 2000 Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (3) (1) (2) Rg RF Voltmeter E1 R2 E2 S.S.G. 0dBm Rg+R1=R2=Input/Output Impedance E1: S.S.G. Output Voltage (1): Input (2): Ground (3): Output 5 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics SFPKA455KE4A-R1 0 10 360 10 20 320 20 30 280 30 40 240 40 50 200 60 160 70 120 70 80 80 80 90 40 90 0 100 200 430 455 Frequency (kHz) 480 Attenuation (dB) 400 100 6 SFPKA455KE4A-R1 0 G.D.T. (μsec.) Attenuation (dB) 1 50 60 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr kHz SMD Type CFUKG Series MARKING EIAJ CODE 1.0±0.1 7.5 max. 6.5±0.3 The CFUKG series is comprised of small, high-performance, thin (4.0mm) filters consisting of 4 ceramic elements. Their innovative construction is perfect for shrinking mobile communication products such as pocket pagers and cellular phones. 2 C0.5 1.2±0.1 4.0 max. 1.0±0.1 c Features 4.0±0.3 1.0±0.3 1.0±0.3 1.5±0.3 6.0±0.3 1. The filters are mountable by automatic placers. 2. The filters can be reflow soldered and withstand washing. 3. They are slim, at only 4.0mm maximum thickness, and have a small mounting area (7.5x6.0mm) enabling flexible PCB design. 4. The bandwidth ranges from D to G. 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (1) 1.5±0.3 3.0±0.3 Connection (1): Input (2): Output (3): Ground (2) (3) (in mm) Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) Stop Band Attenuation (dB) Insertion Loss (dB) Ripple (dB) Input/Output Impedance (ohm) CFUKG455KD4A-R0 455 ±1.5kHz fn±10.0 min. fn±20.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 2.0 max. [within fn±7kHz] 1500 CFUKG455KE4A-R0 455 ±1.5kHz fn±7.5 min. fn±15.0 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±5kHz] 1500 CFUKG455KF4A-R0 455 ±1.5kHz fn±6.0 min. fn±12.5 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±4kHz] 1500 CFUKG455KG1A-R0 455 ±1.0kHz fn±4.5 min. fn±10.0 max. [within 40dB] 25 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1.5 max. [within fn±3kHz] 1500 Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (1) (2) Rg R2 E1 S.S.G. 0dBm (3) E2 RF Voltmeter Connection (1): Input (2): Output (3): Ground Rg+R1=R2=Input/Output Impedance 7 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFUKG455KE4A-R0 CFUKG455KE4A-R0 0 2 0 400 10 10 20 20 30 40 40 200 50 60 70 Attenuation (dB) 30 G.D.T. (μsec.) Attenuation (dB) 300 50 60 70 100 80 80 90 90 100 430 455 Frequency (kHz) 8 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr kHz SMD Type CFUKG_X Series 6.5±0.3 MARKING EIAJ CODE 1.0±0.1 7.5 max. 3 The CFUKG_X series is comprised of small, highperformance, thin (4.0mm) filters consisting of 4 ceramic elements. The filters exhibit an extremely flat GDT characteristic combined with a narrow bandwidth. The filters are recommended for narrow band digital communication applications. C0.5 1.0±0.3 4.0±0.3 6.0±0.3 1.0±0.3 1.5±0.3 1.5±0.3 c Features (1) 1. The filters are mountable by automatic placers. 2. The filters can be reflow soldered and withstand washing. 3. They are slim, at only 4.0mm maximum thickness, and have a small mounting area (7.5x6.0mm) enabling flexible PCB design. 4. The bandwidth ranges from E to H. 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) Center 6dB Frequency (fo) Bandwidth (kHz) (kHz) Part Number Stop Bandwidth (kHz) 1.2±0.1 4.0 max. 1.0±0.1 3.0±0.3 Connection (1): Input (2): Output (3): Ground (2) (3) (in mm) Stop Band Attenuation (dB) Insertion Loss (dB) Ripple (dB) GDT Deviation (µs) Input/Output Impedance (ohm) CFUKG455KE4X-R0 455 ±1.5kHz fn±7.5 min. fn±17.5 max. 27 min. 6.0 max. 1.0 max. 25.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] [within fn±5kHz] [within fn±5kHz] 1500 CFUKG455KF4X-R0 455 ±1.5kHz fn±6.0 min. fn±15.0 max. 27 min. 6.0 max. 1.0 max. 25.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] [within fn±4kHz] [within fn±4kHz] 1500 CFUKG455KG1X-R0 455 ±1.0kHz fn±4.5 min. fn±12.5 max. 25 min. 6.0 max. 1.0 max. 25.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] [within fn±3kHz] [within fn±3kHz] 1500 CFUKG455KH1X-R0 455 ±1.0kHz fn±3.0 min. fn±10.0 max. 25 min. 7.0 max. 1.0 max. 25.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] [within fn±2kHz] [within fn±2kHz] 1500 Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (1) (2) Rg E1 S.S.G. 0dBm R2 (3) E2 RF Voltmeter Connection (1): Input (2): Output (3): Ground Rg+R1=R2=Input/Output Impedance 9 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFUKG455KE4X-R0 CFUKG455KE4X-R0 0 0 200 10 10 20 20 150 30 40 40 100 50 60 70 Attenuation (dB) 30 G.D.T. (μsec.) Attenuation (dB) 3 50 60 70 50 80 80 90 90 100 430 455 Frequency (kHz) 10 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment 6.5±0.3 The CFUKF series is comprised of small, high-performance, thin (4.0mm) filters consisting of 4 ceramic elements. The filters exhibit an extremely flat GDT characteristic. The filters are recommended for digital communication applications and are perfect in hand-held cellular phones, etc. MARKING EIAJ CODE 1.0±0.1 7.5 max. CERAFILr kHz SMD Type CFUKF Series C0.5 1.0±0.3 4.0±0.3 6.0±0.3 1.0±0.3 1.5±0.3 1.5±0.3 c Features (1) 1. The filters are mountable by automatic placers. 2. The filters can be reflow soldered and withstand washing. 3. They are slim, at only 4.0mm maximum thickness, and have a small mounting area (7.5x6.0mm) enabling flexible PCB design. 4. The bandwidth ranges from A to E. 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) Center 6dB Frequency (fo) Bandwidth (kHz) (kHz) Part Number Stop Bandwidth (kHz) 4 1.2±0.1 4.0 max. 1.0±0.1 3.0±0.3 Connection (1): Input (2): Output (3): Ground (2) (3) (in mm) Stop Band Attenuation (dB) Insertion Loss (dB) Ripple (dB) GDT Deviation (µs) Input/Output Impedance (ohm) CFUKF455KA2X-R0 455 ±2.0kHz fn±17.5 min. fn±40.0 max. 25 min. 4.0 max. 1.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] [within fn±12kHz] 15.0 max. [within fn±12kHz] 1000 CFUKF455KB4X-R0 455 ±1.5kHz fn±15.0 min. fn±35.0 max. 25 min. 5.0 max. 1.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] [within fn±10kHz] 15.0 max. [within fn±10kHz] 1000 CFUKF455KC4X-R0 455 ±1.5kHz fn±12.5 min. fn±30.0 max. 25 min. 6.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] 1.0 max. [within fn±8kHz] 15.0 max. [within fn±8kHz] 1000 CFUKF455KD1X-R0 455 ±1.0kHz fn±10.0 min. fn±25.0 max. 23 min. 7.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] 1.0 max. [within fn±7kHz] 20.0 max. [within fn±7kHz] 1500 CFUKF455KE1X-R0 455 ±1.0kHz fn±7.5 min. fn±20.0 max. 23 min. 8.0 max. [within 40dB] [within fn±100kHz] [at minimum loss point] 1.0 max. [within fn±5kHz] 20.0 max. [within fn±5kHz] 1500 Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (1) (2) Rg R2 E1 S.S.G. 0dBm (3) E2 RF Voltmeter Connection (1): Input (2): Output (3): Ground Rg+R1=R2=Input/Output Impedance 11 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFUKF455KE1X-R0 CFUKF455KE1X-R0 0 0 200 10 10 20 20 30 40 40 100 50 60 70 Attenuation (dB) 4 30 G.D.T. μ(sec.) Attenuation (dB) 150 50 60 70 50 80 80 90 90 100 430 455 Frequency (kHz) 12 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment MARKING 6.5 The CFWKA series is comprised of small, high-performance, thin (3.0mm) filters consisting of 6 ceramic elements. The filters are recommend for pager or hand-held cellular phones. 7.5 max. CERAFILr kHz SMD Type CFWKA Series EIAJ CODE Dot marking Sealing 1.2±0.1 Nominal Center 3dB 6dB Frequency (fn) Bandwidth Bandwidth (kHz) (kHz) (kHz) Part Number 3.0 (1) (4) 3.0max. 1. The filters are mountable by automatic placers. 2. The filters can be reflow soldered. 3. They are slim, at only 3.0mm maximum thickness. 4. The filters are wide bandwidth, flat GDT within pass band. 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) C0.3 1.2±0.1 1.2±0.1 c Features 5.5 3.0 1.5±0.3 11.5 1.2±0.1 5.5 3.0 1.5±0.3 Sealing 5 (1): Input (2): Output (3)(4): Ground (2) (3) ( Tolerance ±0.3mm in mm ) Stop Bandwidth (kHz) Stop Band Attenuation (dB) Stop Band Att.(2) (dB) Insertion Loss (dB) Ripple (dB) Input/Output Impedance (ohm) CFWKA450KDFA-R0 450.0 - fn±10.0 min. fn±20.0 max. 50 min. [within 50dB] [within fn±100kHz] - 4.0 max. [at minimum loss point] 3.0 max. [within fn±7kHz] 1500 CFWKA450KEFA-R0 450.0 - fn±7.5 min. fn±15.0 max. 50 min. [within 50dB] [within fn±100kHz] - 6.0 max. [at minimum loss point] 3.0 max. [within fn±5kHz] 1500 CFWKA450KEFA001-R0 450.0 fn±6.5 min. - 4.0 max. [at fn] 3.0 max. [within fn±6.5kHz] 1500 CFWKA450KFFA-R0 450.0 - fn±6.0 min. fn±12.5 min. 50 min. [within 50dB] [within fn±100kHz] - 6.0 max. [at minimum loss point] 3.0 max. [within fn±4kHz] 1500 CFWKA450KGFA-R0 450.0 - fn±4.5 min. fn±11.0 max. 50 min. [within 50dB] [within fn±100kHz] - 6.0 max. [at minimum loss point] 2.0 max. [within fn±3kHz] 1500 fn±15.0 max. 55 min. 50 min. [within 50dB] [fn±18 to ±33kHz] [within fn±100kHz] For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 Rg (1) (2) (4) (3) E1 R2 E2 S.S.G. 0dBm RF Voltmeter Connection (1): Input (2): Output (3)(4): Ground Rg+R1=R2=Input/Output Impedance 13 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFWKA450KEFA001-R0 0 CFWKA450KEFA001-R0 0 400 10 4 20 8 300 30 200 20 24 28 Attenuation (dB) 16 G.D.T. (μ sec.) Attenuation (dB) 12 40 50 60 70 100 5 32 80 36 90 40 0 440.0 450.0 100 460.0 430 Frequency (kHz) CFWKA450KEFA001-R0 0 10 20 Attenuation (dB) 30 40 50 60 70 80 90 100 200 300 400 500 600 700 Frequency (kHz) 14 455 Frequency (kHz) 800 900 1000 480 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment Y50 B1 6.5 The CFWKA_Y series is comprised of small, highperformance, thin (3.0mm) filters consisting of 6 ceramic elements. The filters are recommend for digital communication applications and are perfect in hand-held cellular phones. EIAJ CODE Dot marking Sealing 5.5 3.0 1.5±0.3 11.5 3.0 1. The filters are mountable by automatic placers, and can be reflow soldered. 2. They are slim, at only 3.0mm maximum thickness. 3. The filters are wide bandwidth, flat GDT within pass band. 4. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) Nominal Center 3dB 6dB Frequency (fn) Bandwidth Bandwidth (kHz) (kHz) (kHz) CFWKA450KBFY001-R0 450.0 fn±11.5 min. fn±13.0 min. Stop Bandwidth (kHz) 1.2±0.1 3.0 max. 1.2±0.1 c Features Part Number 7.5 max. CERAFILr kHz SMD Type CFWKA_Y Series (1) (4) C0.3 1.2±0.1 1.2±0.1 5.5 3.0 1.5±0.3 Sealing (2) (3) (1): Input (2): Output (3)(4): Ground ( Tolerance ±0.3mm in mm ) Stop Band Attenuation (dB) Insertion Loss (dB) Spurious Response (dB) GDT Deviation (µs) fn±30.0 max. 45 min. 4.0 max. 20 min. 30.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] [within 0.1 to 1.0MHz] [within fn±10kHz] Input/Output Impedance (ohm) 1000 For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 Rg (1) (2) (4) (3) E1 R2 E2 S.S.G. 0dBm RF Voltmeter Connection (1): Input (2): Output (3)(4): Ground Rg+R1=R2=Input/Output Impedance 15 6 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics 0 0 200 10 2 4 20 150 8 10 100 12 14 Attenuation (dB) 30 G.D.T. (μ sec.) Attenuation (dB) 6 40 50 60 70 50 16 80 18 90 20 0 420 6 430 440 450 460 Frequency (kHz) 16 470 480 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 kHz SMD Type CERAFILr Notice c SFPKA/CFUKG/CFUKF Series Notice o Soldering and Mounting 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. 0EAK (260°C max.) Temperature (°C) 260 230 Heating (230°C) Pre-heating 100 (150-180°C) 30 sec. min. 60-120 sec. Gradual Cooling SEC max. 120 sec. min. (2) Soldering Iron Electrode is directly soldered with the tip of soldering iron at +350±5°C for 3.0±0.5 seconds. (3) Other Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. 2. Wash (1) Cleaning Solvent CFC alternatives (HCFC Series), Isopropyl Alcohol (IPA), 7ATER $EMINERALIZED 7ATER #LEANING 7ATER 3OLUTION (Cleanthrough-750H, Pine Alpha 100S), Silicon 4ECHNOCARE &27 (2) Cleaning Conditions s )MMERSION 7ASH 2 minutes max. in above solvent at +60°C max. s 3HOWER OR 2INSE 7ASH 2 minutes max. in above solvent at +60°C max. (3) Notice s 7HEN COMPONENTS ARE IMMERSED IN SOLVENT BE SURE TO maintain the temperature of components below the temperature of solvent. s 0LEASE DO NOT USE ULTRASONIC CLEANING s 4OTAL WASHING TIME SHOULD BE MINUTES MAXIMUM s 0LEASE ENSURE THE COMPONENT IS THOROUGHLY EVALUATED IN your application circuit. s 0LEASE DO NOT USE CHLORINE PETROLEUM OR ALKALI CLEANING solvent. s )F YOU PLAN TO USE ANY OTHER TYPES OF SOLVENTS PLEASE consult with Murata or Murata representative prior to using. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. Continued on the following page. 17 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 kHz SMD Type CERAFILr Notice Continued from the preceding page. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid such places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. If the component is cleaned, please confirm that the reliability has not been degraded. 2. The components, packed in a moisture-proof bag (dry pack), are sensitive to moisture. The following treatment is required before applying reflow soldering, to avoid package cracks or reliability degradation caused by thermal stress. When unpacked, store the component in an atmosphere of below 25°C and below 65%R.H., and solder within 48 hours. 18 3. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 kHz SMD Type CERAFILr Notice c CFWKA Series Notice o Soldering and Mounting 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Peak (260°C max.) Temperature (°C) 260 230 Heating (230°C) Pre-heating 100 (150-180°C) 30 sec. min. 60-120 sec. Gradual Cooling 40 sec. max. 120 sec. min. (2) Soldering Iron Electrode is directly soldered with the tip of soldering iron at +350±5°C for 3.0±0.5 seconds. (3) Other Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating Do not apply conformal coating onto the component as it's not hermetically sealed. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to + 40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. Continued on the following page. 19 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. kHz SMD Type CERAFILr Notice Continued from the preceding page. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 20 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr MHz SMD Type SFECF10M7 Series SFECF10M7 series for FM receivers are small, high-performance and super thin (1.4mm max.) filters. The piezoelectric element is sandwiched by the ceramics substrate. They have 1.4mm max. thickness and a small mounting area (3.45x3.1mm). SFECF series and CDSCB series (MHz Discriminator) enable customers to make VICS/RKE/TPMS set very thin and small. 1.3±0.1 3.1±0.2 3.45±0.2 Input electrode marker 0 to 0.4 (0.6) (0.6) (0.6) 0 to 0.4 (1.28)(1.28) 0.3 min. 0.3 min. c Features (1) (6) (2) (3) (5) (4) (1.28)(1.28) 0 to 0.35 1. The filters are mountable by automatic placers. 2. They are slim, at only 1.4mm max. thickness, and have a small mounting area (3.45x3.1mm) enabling flexible PCB design. 3. Various bandwidths are available. Select a suitable type in accordance with the desired selectivity. 4. Operating Temperature Range: -20 to +80 (°C)(Standard Type) -40 to +85 (°C)(High-reliability Type) Storage Temperature Range: -40 to +85 (°C)(Standard Type) -55 to +85 (°C)(High-reliability Type) 0.75±0.3 0.85±0.3 0.85±0.3 0.65±0.3 0.7±0.3 0.65±0.3 (1): Input (2)(5): Ground (3)(4): No connect (6): Output : EIAJ Monthly Code ( ): Reference (in mm) 0 to 0.35 7 Standard Type Part Number Center Nominal Center Frequency Frequency (fn) (fo) (MHz) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Ripple (dB) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFECF10M7HA00-R0 10.700 ±30kHz - 180 ±40kHz 470 max. 4.0±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7HF00-R0 - 10.700 fn±25 min. 510 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7GA00-R0 10.700 ±30kHz - 230 ±50kHz 510 max. 3.5±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7GF00-R0 - 10.700 fn±45 min. 560 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7FA00-R0 10.700 ±30kHz - 280 ±50kHz 590 max. 3.0±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7FF00-R0 - 10.700 fn±65 min. 620 max. 7.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7EA00-R0 10.700 ±30kHz - 330 ±50kHz 700 max. 3.0±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7DA0001-R0 10.700 ±30kHz - 420 min. 950 max. 3.0±2.0dB 3.0 max. 35 min. 25 min. [within 9MHz to fo] [within fo to 12MHz] 330 - 10.700 fn±150 min. 990 max. 6.0max. [at fn] 3.0 max. 20 min. 20 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7DF00-R0 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Area of Ripple: within 3dB B.W. Center frequency (fo) defined by center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. 21 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 High-reliability Type Center Nominal Center Frequency Frequency (fn) (fo) (MHz) (MHz) Part Number Attenuation Insertion Loss (kHz) (dB) Spurious Attenuation (1) (dB) Ripple (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFECF10M7HA00S0-R0 10.700 ±30kHz - 180 ±40kHz 470 max. 4.0±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7HF00S0-R0 - 10.700 fn±25 min. 510 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7GA00S0-R0 10.700 ±30kHz - 230 ±50kHz 510 max. 3.5±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7GF00S0-R0 - 10.700 fn±45 min. 560 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7FA00S0-R0 10.700 ±30kHz - 280 ±50kHz 590 max. 3.0±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7FF00S0-R0 - 10.700 fn±65 min. 630 max. 7.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7EA00S0-R0 10.700 ±30kHz - 330 ±50kHz 700 max. 3.0±2.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7DF00S0-R0 - 10.700 fn±145 min. 990 max. 6.0max. [at fn] 3.0 max. 20 min. 20 min. [within 9MHz to fn] [within fn to 12MHz] 330 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Area of Ripple: within 3dB B.W. Center frequency (fo) defined by center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit (3) (4) (2) (5) R1 (6) (1) Rg E1 C2 R2 E2 RF Voltmeter S.S.G. Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5% C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance of RF Volt Meter) E1: S.S.G. Output Voltage (1): Input (2)(5): Ground (3)(4): No connect (6): Output c Frequency Characteristics SFECF10M7FA00-R0 7.0 0 1 6.0 10 2 5.0 20 3 4.0 4 3.0 5 2.0 50 6 1.0 60 7 10.500 10.700 Frequency (MHz) 10.900 0.0 11.100 Attenuation (dB) 0 10.300 22 SFECF10M7FA00-R0 G.D.T. (μsec.) Attenuation (dB) 7 3dB Bandwidth (kHz) 30 40 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr MHz SMD Type SFSCE10M7 Series 4.5 (1.8) (0.3) (4) (3) (1) (2) (2.25) 0.6 1.1 0.85 0.15 1.0 max. (4.0) (4-R0.3) 1. The filters are mountable by automatic placers. 2. They are slim, at only 1.0mm max. thickness, and have a small mounting area (4.5x3.8mm) enabling flexible PCB design. 3. Available lead (Pb) free solder reflow. 4. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (3.5) * (3) (4) c Features 0.4 (2) 3.8 (1) (1): Input (2): Output (3): No Connect (4): Ground * : EIAJ Monthly Code Tolerance unless otherwise specified: ±0.1 ( ): Reference 0.15 (in mm) 0.3 SFSCE series are chip surface mount filters available for 3dB bandwidth at 700kHz to 1.3MHz. (more than twice width compared with current types) They have 1.0mm max. thickness and small mounting area (4.5x3.8mm). 8 c Applications 1. SS digital communication system 2. Digital wireless audio 3. PHS Evolution system 4. RFID Reader Writer 5. RKE Nominal Center 3dB Frequency (fn) Bandwidth (MHz) (kHz) Part Number Stop Bandwidth (MHz) Insertion Loss (dB) Ripple (dB) Spurious Response (dB) GDT Deviation (µs) Input/Output Impedance (ohm) SFSCE10M7WF03-R0 10.700 fn±500.0 min. 2.2 max. (Total) 6.0 max. 2.0 max. 30/25 min. 0.6 max. [within 20dB] [at minimum loss point] [within 3dB Bandwidth] [within 5.7MHz to fn / fn to 15.7MHz] [within fn±400kHz] 470 SFSCE10M7WF04-R0 10.700 fn±400.0 min. 1.8 max. (Total) 6.0 max. 1.5 max. 35/25 min. 0.6 max. [within 20dB] [at minimum loss point] [within 3dB Bandwidth] [within 5.7MHz to fn / fn to 15.7MHz] [within fn±325kHz] 470 SFSCE10M7WF05-R0 10.700 fn±325.0 min. 1.7 max. (Total) 6.0 max. 1.5 max. 40/30 min. 0.6 max. [within 20dB] [at minimum loss point] [within 3dB Bandwidth] [within 5.7MHz to fn / fn to 15.7MHz] [within fn±250kHz] 470 For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit (4) (3) (1) (2) R1 Rg R2 S.S.G. C2 RF Voltmeter (1): Input (2): Output (3): No Connect (4): Ground R1+Rg=R2=Input/Output Impedance, Rg=50Ω C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1: S.S.G. Output Voltage 23 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics SFSCE10M7WF03-R0 SFSCE10M7WF03-R0 0 2.0 2 1.6 0 1.2 6 0.8 8 0.4 Attenuation (dB) 4 G.D.T. (μsec.) Attenuation (dB) 20 40 60 10 9.500 9.900 10.300 10.700 11.100 Frequency (MHz) 8 24 11.500 0.0 11.900 80 6.700 8.700 10.700 Frequency (MHz) 12.700 14.700 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 MHz SMD Type CERAFILr Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (°C) c SFECF10M7 Series Notice o Soldering and Mounting Peak (260°C max.) 260 230 Pre-heating (150-180°C) 100 Heating (230°C) Gradual Cooling 30 sec. min. 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +350±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Condition for Placement Machines The component is recommended with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent the electrode erosion. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. [Component Direction] Place the component lateral to the direction in which stress acts. [Component Layout Close to Board] Perforation A B Slit C Susceptibility to stress is in the order of : A>C>B Continued on the following page. 25 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 MHz SMD Type CERAFILr Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. The components, packed in a moisture proof bag (dry pack), are sensitive to moisture. The following treatment is required before applying reflow soldering, to avoid reliability degradation caused by thermal stress. When unpacked, store the component in an atmosphere of reflow 30°C and below 60%R.H., and solder within 1 week. 26 3. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 MHz SMD Type CERAFILr Notice c SFSCE10M7WF03-R0 Notice o Soldering and Mounting 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Peak (240°C max.) Temperature (°C) 240 230 Heating (230°C) Pre-heating 100 (150-180°C) 30 sec. min. Gradual Cooling 60-120 sec. 30 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +280±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Condition for Placement Machines The component is recommended with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. [Component Layout Close to Board] Perforation A Susceptibility to stress is in the order of : A>C>B B Slit C [Component Direction] Place the component laterally to the direction in which stress acts. Continued on the following page. 27 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 MHz SMD Type CERAFILr Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to + 40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 28 (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 MHz SMD Type CERAFILr Notice c SFSCE10M7WF04/05-R0 Notice o Soldering and Mounting 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Peak (260°C max.) Temperature (°C) 260 230 Heating (230°C) Pre-heating 100 (150-180°C) 30 sec. min. Gradual Cooling 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +280±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Condition for Placement Machines The component is recommended with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. [Component Layout Close to Board] Perforation A Susceptibility to stress is in the order of : A>C>B B Slit C [Component Direction] Place the component laterally to the direction in which stress acts. Continued on the following page. 29 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 MHz SMD Type CERAFILr Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to + 40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 30 (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 SMD Type CERAFILr Standard Land Pattern Dimensions c SFPKA Series c CFUKG/CFUKF Series 0.7 1.2 0.8 6.95 2.0 0.7 1.4 1.2 2.0 0.9 1.1 0.925 2.0 1.55 3.5 7.45 2.0 1.6 2.475 2.0 (in mm) (in mm) c SFECF10M7 Series 3.0 (6) (5) (4) (1) (2) (3) 0.5 1.05 0.1 2.1 1.6 4-R3.0 0.1 6.5 7.5 0.3 0.1 1.40 0.3 1.2 1.05 11.5 5.5 3.0 0.1 0.3 0.1 c CFWKA Series 0.1 0.8 0.6 0.8 0.6 1.8 (in mm) It shows solder resist land pattern. 0.8 (1): Input (2)(5): Ground (3)(4): No connect (6): Output (in mm) c SFSCE10M Series 1.05 1.4 0.1 (4) 0.5 1.15 0.8 1.3 (3) 0.1 0.1 (2) (1) 0.5 It shows solder resist land pattern. (1): Input (2): Output (3): No Connect (4): Ground (in mm) 31 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 kHz SMD Type CERAFILr Packaging c Minimum Quantity Part Number ø180mm ø330mm SFPKA 1,000 CFUKG 450 CFUKF 450 CFWKA 350 c SFPKA Series Dimensions of Carrier Tape Trailer 160 to 190 1.75±0.1 Empty Leader Cover film Components Empty 240 to 280 ø13.0±0.2 80±1 330±2 400 to 560 8.8±0.1 +0.1 -0 7.5±0.1 2.0±0.1 ø1.5 16.0±0.2 4.0±0.1 Dimensions of Reel 2.2±0.5 12.0±0.1 User direction of feed 5.3±0.1 Cover film Label 17.5±0.5 21.5±1.0 7.4±0.1 s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP (in mm) c CFUKG/CFUKF Series Dimensions of Carrier Tape 8.0±0.1 6.7±0.1 5SER DIRECTION OF FEED Cover film (ø60 +1.0 -0 ) (ø180+0 -3.0 ) 7.7±0.1 8.1±0.1 Empty 16.0±0.2 ø1.5 +0.1 -0.0 6.76±0.1 7.5±0.1 2.0±0.1 Trailer 160 to 190 1.75±0.1 4.0±0.1 Dimensions of Reel Leader Cover film Components 2.0±0.2 ø13.0±0.5 Empty 160 to 200 400 to 560 4.2±0.1 17.0±1.0 19.4±0.3 6.3±0.1 s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP (in mm) Continued on the following page. 32 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 kHz SMD Type CERAFILr Packaging Continued from the preceding page. c CFWKA Series Dimensions of Carrier Tape 1.75±0.1 Trailer 160 to 190 (ø178±2.0) (ø62.0±1.0) 12.0±0.1 Empty 12.4±0.1 11.5±0.1 ø1.5 +0.1 -0.0 24.0±0.3 4.0±0.1 2.0±0.1 Dimensions of Reel Leader Cover film Components 2.0±0.2 ø13.0±0.5 Empty 240 to 280 400 to 560 25.5±1.0 0.4±0.1 12.0±0.1 8.1±0.1 7.7±0.1 29.9±1.0 3.2±0.1 User direction of feed Cover film s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP (in mm) 33 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 MHz SMD Type CERAFILr Packaging c Minimum Quantity Part Number ø180mm SFECF 2,000 SFSCE 1,500 c SFECF10M7 Series Dimensions of Carrier Tape Dimensions of Reel Cover film (3°) 10° max. 3° max. Leader Cover film Components Empty 240 to 280 400 to 560 180 +0 -1.5 ø13.0±0.5 60 +1.0 -0 12.0±0.2 5.5±0.05 Empty 2.0±0.5 4.1±0.1 Peeling strength (0.1 to 0.7N) +0.1 3.35 -0.05 (0.05) 4.0±0.1 0.3±0.05 4.1±0.1 Chip filter 1.84±0.1 ø1.55±0.05 2.0±0.05 Trailer 160 to 190 1.75±0.1 4.0±0.1 17.0±1.0 13.0 +1.0 -0 User direction of feed ( ): Reference (in mm) s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP c SFSCE10M7 Series Dimensions of Reel ,EADER Cover film Trailer TO ± ± ± %MPTY ± MAX ± %MPTY TO TO ± ± ± #OMPONENTS ± ± ± Dimensions of Carrier Tape ± 0EELING STRENGTH TO . Cover film ± (3°) MAX ± ± ± 5SER DIRECTION OF FEED s 0ART .UMBER MARKED SIDE IS ALWAYS FACING UP (in mm) 34 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case General Use CFULA Series 8.0±0.3 7.0±0.3 MARKING 2.7±0.3 1. High selectivity 2. A variety of bandwidths available 3. Excellent GDT characteristics are available within pass bandwidth. 4. Easily mounted on a printed circuit board 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (2) 0.8±0.1 3.0±0.3 0.15±0.05 c Features 1.2±0.5 (1) (3) 4.2±0.3 1.5 max. 7.3±0.3 EIAJ CODE 0.3±0.1 CFULA series are high selectivity ceramic filters, which consist of 4 ceramic elements connected in a ladder form. They are most suitable for digital communications and cellular phones because of their improved GDT characteristics. 3.3±0.5 0.6±0.1 Connection (1): Input (2): Ground (3): Output (in mm) Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) Stop Band Attenuation (dB) Insertion Loss (dB) Input/Output Impedance (ohm) CFULA455KB2A-B0 455 ±2.0kHz fn±15.0 min. fn±30.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFULA455KC2A-B0 455 ±2.0kHz fn±12.5 min. fn±24.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFULA455KD4A-B0 455 ±1.5kHz fn±10.0 min. fn±20.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFULA455KE4A-B0 455 ±1.5kHz fn±7.5 min. fn±15.0 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1500 CFULA455KF4A-B0 455 ±1.5kHz fn±6.0 min. fn±12.5 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFULA455KG1A-B0 455 ±1.0kHz fn±4.5 min. fn±10.0 max. [within 40dB] 25 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFULA455KH1A-B0 455 ±1.0kHz fn±3.0 min. fn±9.0 max. [within 40dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 Part Number 9 Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 Rg E1 (3) (1) (2) R2 E2 S.S.G. 0dBm RF Voltmeter Connection (1): Input (2): Ground (3): Output Rg+R1=R2=Input/Output Impedance 35 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFULA455KE4A-B0 CFULA455KE4A-B0 0 0 200 10 10 20 20 30 40 40 100 50 60 Attenuation (dB) 30 G.D.T. (μsec.) Attenuation (dB) 150 50 60 70 70 50 80 80 90 90 100 430 455 Frequency (kHz) 9 36 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case General Use CFWLA Series 7.5±0.5 EIAJ CODE 0.15 1. Low profile, high selectivity 2. Available bandwidths are B to J as standard 3. Easily mountable on any PC board 4. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) Nominal Center 6dB Frequency (fn) Bandwidth (kHz) (kHz) Part Number 2.9±0.3 0.8±0.1 3.5±0.5 c Features 2.6±0.3 2.9±0.3 2.9—0.3 (4) (3) Stop Bandwidth (kHz) Stop Band Attenuation (dB) (2) (1) (5) Insertion Loss (dB) 4.3±0.3 1.35±0.5 1.2±0.5 2.3±0.5 1.5 max. MARKING 7.0±0.5 11.0±0.5 Ceramic filter CFWLA series are low profile high selectivity ceramic filters, which use 6 elements in ladder form. They are best suitable to high-class transceivers, cordless telephones and amateur radios. 0.6±0.1 Connection (1): Input (2)(3)(4): Ground (5): Output (in mm) 2.0±0.3 Ripple (dB) Input/Output Impedance (ohm) CFWLA455KBFA-B0 455.0 fn±15.0 min. fn±30.0 max. 35 min. 4.0 max. 3.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] [within fn±10kHz] 1500 CFWLA455KCFA-B0 455.0 fn±12.5 min. fn±24.0 max. 35 min. 4.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] 3.0 max. [within fn±8kHz] 1500 CFWLA455KDFA-B0 455.0 fn±10.0 min. fn±20.0 max. 35 min. 4.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] 3.0 max. [within fn±7kHz] 1500 CFWLA455KEFA-B0 455.0 fn±7.5 min. fn±15.0 max. 35 min. 6.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] 3.0 max. [within fn±5kHz] 1500 CFWLA455KFFA-B0 455.0 fn±6.0 min. fn±12.5 max. 35 min. 6.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] 3.0 max. [within fn±4kHz] 2000 CFWLA455KGFA-B0 455.0 fn±4.5 min. fn±10.0 max. 35 min. 6.0 max. [within 50dB] [within fn±100kHz] [at minimum loss point] 2.0 max. [within fn±3kHz] 2000 CFWLA455KHFA-B0 455.0 fn±3.0 min. fn±9.0 max. [within 50dB] 60 min. 6.0 max. [within fn±100kHz] [at minimum loss point] 2.0 max. [within fn±2kHz] 2000 CFWLA455KJFA-B0 455.0 fn±2.0 min. fn±7.5 max. [within 50dB] 60 min. 7.0 max. 2.0 max. [within fn±100kHz] [at minimum loss point] [within fn±1.5kHz] 10 2000 For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit (5) R1 (1) (2) (3) (4) R2 E2 Rg E1 S.S.G. 0dBm RF Voltmeter Connection (1): Input (5): Output (2)(3)(4): Ground Rg+R1=R2=Input/Output Impedance 37 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFWLA455KEFA-B0 CFWLA455KEFA-B0 0 400 0 10 10 20 20 30 40 40 200 50 60 70 Attenuation (dB) 30 G.D.T. (μsec.) Attenuation (dB) 300 50 60 70 100 80 80 90 90 100 430 455 Frequency (kHz) 10 38 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case Miniaturized Type CFULB Series CFULB series ceramic filters are miniature, highperformance ceramic filters composed of piezoelectric elements connected in a ladder form. These filters, only 6.3mm high, are 65% the volume of conventional types. They are well suited for miniaturizing various kinds of communications equipment, pocket pagers, car radios, cordless telephones and mobile telephones. 0.15±0.05 (1) c Features (3) 1. Miniature and high selectivity 2. A variety of bandwidths are available 3. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (2) (4) 1.0 max. 0.5±0.1 4.3±0.3 0.8±0.3 1.8±0.3 0.7±0.3 Connection (1): Input (2): Output (3) : Ground (4) 1.0±0.3 2.4±0.3 0.7±0.1 3.5±0.3 6.3±0.3 EIAJ CODE 6.5±0.3 6.5±0.3 MARKING (in mm) } Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) Stop Band Attenuation (dB) Insertion Loss (dB) Input/Output Impedance (ohm) CFULB455KB2A-B0 455 ±2.0kHz fn±15.0 min. fn±30.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFULB455KC2A-B0 455 ±2.0kHz fn±12.5 min. fn±24.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFULB455KD4A-B0 455 ±1.5kHz fn±10.0 min. fn±20.0 max. [within 40dB] 27 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFULB455KE4A-B0 455 ±1.5kHz fn±7.5 min. fn±15.0 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1500 CFULB455KF4A-B0 455 ±1.5kHz fn±6.0 min. fn±12.5 max. [within 40dB] 27 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFULB455KG1A-B0 455 ±1.0kHz fn±4.5 min. fn±10.0 max. [within 40dB] 25 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFULB455KH1A-B0 455 ±1.0kHz fn±3.0 min. fn±9.0 max. [within 40dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFULB455KJ1A-B0 455 ±1.0kHz fn±2.0 min. fn±7.5 max. [within 40dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 Part Number 11 Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. CFULB455K_series filters are 4-element ceramic filters and miniature versions of CFULA455K_series. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (1) (2) (3) (4) Rg E1 R2 S.S.G. 0dBm E2 RF Voltmeter Connection (1): Input (2): Output (3)(4): Ground Rg+R1=R2=Input/Output Impedance 39 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFULB455KE4A-B0 CFULB455KE4A-B0 0 0 200 10 10 20 20 30 40 40 100 50 60 Attenuation (dB) 30 G.D.T. (μsec.) Attenuation (dB) 150 50 60 70 70 50 80 80 90 90 100 430 455 Frequency (kHz) 11 40 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case Miniaturized Type CFWLB Series 3.5±0.3 6.3±0.3 EIAJ CODE 0.15±0.05 c Features (3) 1. Miniature and high selectivity 2. A variety of bandwidths are available. 3. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (4) (5) 0.7±0.3 1.0±0.3 (2) (1) 4.3±0.3 2.5±0.3 2.7±0.3 2.8±0.3 0.9±0.3 1.0 max. MARKING 6.5±0.3 9.5±0.3 CFWLB series ceramic filters are miniature, highperformance ceramic filters composed of piezoelectric elements connected in a ladder form. These filters, only 6.3mm high, are 67% the volume of conventional types. They are well suited for miniaturizing various kinds of communications equipment, pocket pagers, pagers, car radios, cordless telephones and mobile telephones. 0.7±0.1 0.5±0.1 Connection (1): Input (2): Output (3) (4) : Ground (5) } (in mm) Nominal Center Frequency (fn) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) Stop Band Attenuation (dB) Insertion Loss (dB) Input/Output Impedance (ohm) CFWLB455KBFA-B0 455.0 fn±15.0 min. fn±30.0 max. [within 50dB] 35 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFWLB455KCFA-B0 455.0 fn±12.5 min. fn±24.0 max. [within 50dB] 35 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFWLB455KDFA-B0 455.0 fn±10.0 min. fn±20.0 max. [within 50dB] 35 min. [within fn±100kHz] 4.0 max. [at minimum loss point] 1500 CFWLB455KEFA-B0 455.0 fn±7.5 min. fn±15.0 max. [within 50dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 1500 CFWLB455KEFA004-B0 455.0 fn±7.5 min. fn±15.0 max. [within 60dB] 60 min. [within fn±15kHz to 30kHz] 5.0 max. [at fn] 1500 CFWLB455KFFA-B0 455.0 fn±6.0 min. fn±12.5 max. [within 50dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFWLB455KGFA-B0 455.0 fn±4.5 min. fn±10.0 max. [within 50dB] 35 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFWLB455KHFA-B0 455.0 fn±3.0 min. fn±9.0 max. [within 50dB] 55 min. [within fn±100kHz] 6.0 max. [at minimum loss point] 2000 CFWLB455KJFA-B0 455.0 fn±2.0 min. fn±7.0 max. [within 50dB] 55 min. [within fn±100kHz] 7.0 max. [at minimum loss point] 2000 Part Number 12 CFWLB455K_series filters are 4-element ceramic filters and miniature versions of CFWLA455K_series. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. 41 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Test Circuit R1 (1) (2) (3) (4) (5) Rg E1 S.S.G. 0dBm R2 RF Voltmeter Connection E2 (1): Input (2): Output (3)(4)(5): Ground Rg+R1=R2=Input/Output Impedance c Frequency Characteristics CFWLB455KEFA-B0 CFWLB455KEFA-B0 0 0 200 10 10 20 20 30 40 40 100 50 60 70 Attenuation (dB) 30 G.D.T. (μsec.) Attenuation (dB) 150 50 60 70 50 80 80 90 90 100 430 455 Frequency (kHz) 12 42 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case Group Delay Flat Type CFULA_Y Series 2.7±0.3 1. High selectivity 2. A variety of bandwidths are available. 3. Excellent GDT characteristics are available within pass bandwidth. 4. Easily mounted on a printed circuit board 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (2) (1) (3) 0.8±0.1 3.0±0.3 0.15±0.05 c Features 1.2±0.5 4.2±0.3 1.5 max. 7.3±0.3 EIAJ CODE 0.3±0.1 MARKING 7.0±0.3 8.0±0.3 CFULA_Y series are high selectivity ceramic filters, which consist of 4 ceramic elements connected in a ladder form. They are most suitable for digital communications and cellular phones because of their improved GDT characteristics. 3.3±0.5 0.6±0.1 Connection (1): Input (2): Ground (3): Output (in mm) GDT Deviation (µs) Input/Output Impedance (ohm) 25 min. 5.0 max. [within fn±100kHz] [at minimum loss point] 15.0 max. [within fn±10kHz] 1500 fn±30.0 max. [within 40dB] 25 min. 6.0 max. [within fn±100kHz] [at minimum loss point] 15.0 max. [within fn±8kHz] 1500 fn±10.0 min. fn±25.0 max. [within 40dB] 23 min. 7.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±7kHz] 1500 455 ±1.0kHz fn±7.5 min. fn±20.0 max. [within 40dB] 23 min. 8.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±5kHz] 1500 CFULA455KF1Y-B0 455 ±1.0kHz fn±6.0 min. fn±17.5 max. [within 40dB] 23 min. 9.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±4kHz] 2000 CFULA455KG1Y-B0 455 ±1.0kHz fn±4.5 min. fn±15.0 max. [within 40dB] 23 min. 10.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±3kHz] 2000 Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) CFULA455KB4Y-B0 455 ±1.5kHz fn±15.0 min. fn±35.0 max. [within 40dB] CFULA455KC4Y-B0 455 ±1.5kHz fn±12.5 min. CFULA455KD1Y-B0 455 ±1.0kHz CFULA455KE1Y-B0 Stop Band Attenuation (dB) Insertion Loss (dB) Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. 13 c Test Circuit R1 Rg E1 (3) (1) (2) R2 E2 S.S.G. 0dBm RF Voltmeter Connection (1): Input (2): Ground (3): Output Rg+R1=R2=Input/Output Impedance 43 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFULA455KE1Y-B0 CFULA455KE1Y-B0 0 0 200 10 10 20 20 150 30 100 50 60 70 40 Attenuation (dB) 40 Group Delay Time (μsec) Attenuation (dB) 30 50 60 70 50 80 80 90 90 100 0 430 455 Frequency (kHz) 13 44 480 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case Group Delay Flat Type CFWLA_Y Series 7.5±0.5 EIAJ CODE 2.9±0.3 1. High selectivity 2. A variety of bandwidths are available 3. Excellent GDT characteristics are available within pass bandwidth. 4. Easily mounted on a printed circuit board 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) 0.8±0.1 3.5±0.5 0.15 c Features 2.6±0.3 2.9±0.3 2.9—0.3 (4) (3) (2) (5) (1) 4.3±0.3 1.35±0.5 1.2±0.5 2.3±0.5 1.5 max. MARKING 7.0±0.5 11.0±0.5 CFWLA_Y series are high selectivity ceramic filters, which consist of 6 ceramic elements connected in a ladder form. They are most suitable for digital communications and mobile telephones because of their improved GDT characteristics. 0.6±0.1 Connection (1): Input (2)(3)(4): Ground (5): Output (in mm) 2.0±0.3 GDT Deviation (µs) Input/Output Impedance (ohm) 40 min. 6.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±10kHz] 1500 fn±27.5 max. [within 50dB] 40 min. 7.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±8kHz] 1500 fn±10.0 min. fn±25.0 max. [within 50dB] 40 min. 8.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±7kHz] 1500 455 ±1.0kHz fn±7.5 min. fn±20.0 max. [within 50dB] 40 min. 9.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±5kHz] 1500 CFWLA455KF1Y-B0 455 ±1.0kHz fn±6.0 min. fn±17.5 max. [within 50dB] 40 min. 10.0 max. [within fn±100kHz] [at minimum loss point] 40.0 max. [within fn±4kHz] 2000 CFWLA455KG1Y-B0 455 ±1.0kHz fn±4.5 min. fn±15.0 max. [within 50dB] 40 min. 11.0 max. [within fn±100kHz] [at minimum loss point] 40.0 max. [within fn±3kHz] 2000 Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) CFWLA455KB4Y-B0 455 ±1.5kHz fn±15.0 min. fn±30.0 max. [within 50dB] CFWLA455KC4Y-B0 455 ±1.5kHz fn±12.5 min. CFWLA455KD1Y-B0 455 ±1.0kHz CFWLA455KE1Y-B0 Stop Band Attenuation (dB) Insertion Loss (dB) Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. 14 c Test Circuit (5) R1 (1) (2) (3) (4) R2 E2 Rg E1 S.S.G. 0dBm RF Voltmeter Connection (1): Input (5): Output (2)(3)(4): Ground Rg+R1=R2=Input/Output Impedance 45 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFWLA455KE1Y-B0 CFWLA455KE1Y-B0 0 0 400 10 10 20 20 300 30 200 50 60 70 40 Attenuation (dB) 40 Group Delay Time (μsec) Attenuation (dB) 30 50 60 70 100 80 80 90 90 100 0 430 455 Frequency (kHz) 14 46 480 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case Group Delay Flat Type Miniaturized Type CFULB_Y Series Ceramic filter CFULB_Y series are miniature and highperformance filters. These filters, only 6.3mm high, are 65% the volume of conventional types. Well suited for miniaturizing communications equipment, especially for a cellular phone. 0.15±0.05 2.4±0.3 0.8±0.3 1.8±0.3 0.7±0.3 (1) (2) (3) (4) 1.0 max. 0.5±0.1 4.3±0.3 1. Miniature, flat GDT characteristics 2. Suitable for a cellular phone 3. A variety of bandwidths are available. 4. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) Connection (1): Input (2): Output (3) : Ground (4) 1.0±0.3 c Features 0.7±0.1 3.5±0.3 6.3±0.3 EIAJ CODE 6.5±0.3 6.5±0.3 MARKING (in mm) } GDT Deviation (µs) Input/Output Impedance (ohm) 25 min. 5.0 max. [within fn±100kHz] [at minimum loss point] 15.0 max. [within fn±10kHz] 1500 fn±30.0 max. [within 40dB] 25 min. 6.0 max. [within fn±100kHz] [at minimum loss point] 15.0 max. [within fn±8kHz] 1500 fn±10.0 min. fn±25.0 max. [within 40dB] 23 min. 7.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±7kHz] 1500 455 ±1.0kHz fn±7.5 min. fn±20.0 max. [within 40dB] 23 min. 8.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±5kHz] 1500 CFULB455KF1Y-B0 455 ±1.0kHz fn±6.0 min. fn±17.5 max. [within 40dB] 23 min. 9.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±4kHz] 2000 CFULB455KG1Y-B0 455 ±1.0kHz fn±4.5 min. fn±15.0 max. [within 40dB] 23 min. 10.0 max. [within fn±100kHz] [at minimum loss point] 20.0 max. [within fn±3kHz] 2000 Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) CFULB455KB4Y-B0 455 ±1.5kHz fn±15.0 min. fn±35.0 max. [within 40dB] CFULB455KC4Y-B0 455 ±1.5kHz fn±12.5 min. CFULB455KD1Y-B0 455 ±1.0kHz CFULB455KE1Y-B0 Stop Band Attenuation (dB) Insertion Loss (dB) Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. CFULB455K_Y series filters are 4-element ceramic filters and miniature versions of CFULA455K_Y series. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (1) (2) (3) (4) Rg E1 R2 S.S.G. 0dBm E2 15 RF Voltmeter Connection (1): Input (2): Output (3)(4): Ground Rg+R1=R2=Input/Output Impedance 47 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFULB455KE1Y-B0 CFULB455KE1Y-B0 0 0 200 10 10 20 20 150 30 100 50 60 70 40 Attenuation (dB) 40 Group Delay Time (μsec) Attenuation (dB) 30 50 60 70 50 80 80 90 90 100 0 430 455 Frequency (kHz) 15 48 480 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Filters (CERAFILr) for Communications Equipment CERAFILr Plastic Case Group Delay Flat Type CFWLB_Y Series c Features 3.5±0.3 6.3±0.3 EIAJ CODE 0.15±0.05 (3) (4) (5) 0.7±0.3 1.0±0.3 (2) (1) 4.3±0.3 2.5±0.3 2.7±0.3 2.8±0.3 0.9±0.3 1. Miniature, flat GDT characteristics 2. Suitable for a cellular phone 3. A variety of bandwidths are available. 4. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) 1.0 max. MARKING 6.5±0.3 9.5±0.3 Ceramic filter CFWLB_Y series are miniature and high-performance filters. These filters, only 6.3mm high, are 67% the volume of conventional types. Well suited for miniaturizing communications equipment, especially for a cellular phone. 0.7±0.1 0.5±0.1 Connection (1): Input (2): Output (3) (4) : Ground (5) } (in mm) GDT Deviation (µs) Input/Output Impedance (ohm) 40 min. 6.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±10kHz] 1500 fn±27.5 max. [within 50dB] 40 min. 7.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±8kHz] 1500 fn±10.0 min. fn±25.0 max. [within 50dB] 40 min. 8.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±7kHz] 1500 455 ±1.0kHz fn±7.5 min. fn±20.0 max. [within 50dB] 40 min. 9.0 max. [within fn±100kHz] [at minimum loss point] 30.0 max. [within fn±5kHz] 1500 CFWLB455KF1Y-B0 455 ±1.0kHz fn±6.0 min. fn±17.5 max. [within 50dB] 35 min. 10.0 max. [within fn±100kHz] [at minimum loss point] 40.0 max. [within fn±4kHz] 2000 CFWLB455KG1Y-B0 455 ±1.0kHz fn±4.5 min. fn±15.0 max. [within 50dB] 40 min. 11.0 max. [within fn±100kHz] [at minimum loss point] 40.0 max. [within fn±3kHz] 2000 Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Stop Bandwidth (kHz) CFWLB455KB4Y-B0 455 ±1.5kHz fn±15.0 min. fn±30.0 max. [within 50dB] CFWLB455KC4Y-B0 455 ±1.5kHz fn±12.5 min. CFWLB455KD1Y-B0 455 ±1.0kHz CFWLB455KE1Y-B0 Stop Band Attenuation (dB) Insertion Loss (dB) Center frequency (fo) defined by the center of 6dB bandwidth. (fn) means nominal center frequency 455kHz. CFWLB455K_Y series filters are 4-element ceramic filters and miniature versions of CFWLA455K_Y series. For safety purposes, connect the output of filters to the IF amplifier through a DC blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit R1 (1) (2) (3) (4) (5) Rg S.S.G. 0dBm E1 R2 E2 RF Voltmeter Connection 16 (1): Input (2): Output (3)(4)(5): Ground Rg+R1=R2=Input/Output Impedance 49 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Frequency Characteristics CFWLB455KE1Y-B0 CFWLB455KE1Y-B0 0 200 0 10 10 20 20 150 30 100 50 60 70 40 Attenuation (dB) 40 Group Delay Time (μsec) Attenuation (dB) 30 50 60 70 50 80 80 90 90 100 430 455 Frequency (kHz) 16 50 480 0 100 200 300 400 500 600 700 Frequency (kHz) 800 900 1000 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Plastic Case Type CERAFILr Minimum Quantity/Notice c Minimum Quantity Part Number Bulk CFULA Series 200 CFULB Series 250 CFWLA Series 150 CFWLB Series 150 The order quantity should be an integral multiple of the "Minimum Quantity" shown above. (pcs.) c Notice o Soldering and Mounting The component cannot withstand washing. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Do not use this product with bend. The component may be damaged if excessive mechanical stress is applied to it mounted on the printed circuit board. 2. All kinds of reflow soldering must not be applied on the component. 3. Do not clean or wash the component as it is not hermetically sealed. 4. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 5. Conformal coating of the component is not acceptable due to non-sealed construction. 6. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 7. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 51 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Discriminators for Communications Equipment kHz Type Ceramic Discriminators 6.0±0.2 6.2±0.2 MARKING 6.6±0.3 Ceramic discriminator consists of a wide band piezoelectric resonator. It is ideal for mobile communications equipment due to its small size and light weight. Standard line includes products for a wide range of applications, from cordless telecom to cellular telephone. Practically adjustment free at the detection circuit, small size is suitable for downsizing. EIAJ CODE 3.1 max. 1.0±0.1 3.7±0.2 1.15±0.2 c Features 1.5±0.3 CDBKB Series 1. Small in size and light weight 2. Adjustment free at detection circuit 3. High sensitivity and stability 4. Wide range of standard products are available for various ICs. 5. Operating temperature range: -20 to +80 (°C) Storage temperature range: -40 to +85 (°C) (in mm) 6.0±0.2 6.3 max. 0.5±0.1 0.15±0.05 1.8±0.2 0.6±0.2 EIAJ CODE 6.0 max. MARKING 4.2±0.5 3.0±0.3 CDBLB_CAX Series 4.2±0.2 (in mm) 0.9±0.2 6.0±0.2 4.2±0.5 EIAJ CODE 6.3 max. MARKING 6.0 max. 3.0±0.3 0.15±0.05 1.0±0.3 1.5±0.3 0.5±0.1 4.2±0.2 0.9±0.2 0.5±0.2 CDBLB_CAY Series (in mm) Specified by Impedance Characteristics (Type 1) Nominal Center Frequency (fn) (kHz) Inclination of Impedance Curve (1) Inclination of Impedance Curve (2) Capacitance (C) IC IC Maker Type CDBLB455KCAX02-B0 455 447.0±1.5kHz (at |Z|=2.05kohm) 463.0±1.5kHz (at |Z|=10.0kohm) 140pF±20% TA8104F TOSHIBA Lead CDBLB455KCAX31-B0 455 447.0±1.5kHz (at |Z|=2.05kohm) 463.0±1.5kHz (at |Z|=10.0kohm) 140pF±20% TA31141 TOSHIBA Lead Part Number 17 For safety purposes, avoid applying a direct current between the terminals. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. 52 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 c Impedance Curve CDBLB455KCAX02-B0 CDBLB455KCAX31-B0 500K 500K 180 180 100K 100K 50K 50K 0 Impedance (Ω) 5K Phase (deg) Impedance (Ω) 10K 10K 5K 0 1K 1K –90 –90 500 500 100 50 400 Phase (deg) 90 90 100 –180 420 440 460 480 50 400 500 –180 420 440 460 480 500 Frequency (kHz) Frequency (kHz) Specified by Impedance Characteristics (Type 2) Nominal Center Frequency (fn) Anti-resonant Frequency (Fa) Delta F (Fa-Fr) Resonant Resistance (R) Capacitance (C) IC IC Maker Type CDBKB455KCAX33-R0 - 462.0±1.5kHz 40±4.0kHz 200ohm max. 150pF±20% CXA1474 SONY SMD CDBLB455KCAY03-B0 - 455.0±1.5kHz 46±5.0kHz 70ohm max. 550pF±20% CXA1184M SONY Lead CDBLB455KCAX15-B0 - 463.5±1.0kHz 43±2.0kHz 300ohm max. 140pF±20% CXA1183M SONY Lead CDBLB455KCAX25-B0 - 465.0±1.5kHz 45±4.0kHz 300ohm max. 135pF±20% CXA1484 SONY Lead CDBLB455KCAX33-B0 - 465.0±1.5kHz 45±4.0kHz 300ohm max. 135pF±20% CXA1474 SONY Lead Part Number For safety purposes, avoid applying a direct current between the terminals. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Impedance Curve CDBKB455KCAX33-R0 500K CDBLB455KCAY03-B0 180 100K 180 50K 100K 50K 90 10K 90 0 0 1K 500 Phase (deg) 5K Impedance (Ω) 10K Phase (deg) Impedance (Ω) 5K 1K –90 500 –90 100 50 100 –180 50 400 420 440 460 Frequency (kHz) 480 –180 500 10 380 400 420 440 460 480 Frequency (kHz) 17 Continued on the following page. 53 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Continued from the preceding page. c Impedance Curve CDBLB455KCAX15-B0 CDBLB455KCAX25-B0 500K 500K 180 180 100K 100K 50K 50K 90 0 10K 0 5K 1K 1K –90 500 500 100 50 390 100 –180 410 430 450 470 50 400 490 Frequency (kHz) CDBLB455KCAX33-B0 180 100K 90 10K 5K 0 1K 500 –90 100 440 460 Frequency (kHz) 17 54 480 –180 500 Phase (deg) Impedance (Ω) 50K 420 420 440 460 Frequency (kHz) 500K 50 400 –90 480 –180 500 Phase (deg) 5K Impedance (Ω) 10K Phase (deg) Impedance (Ω) 90 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Specified by Recovered Audio Characteristics Part Number Nominal Center Recovered Recovered Distortion Frequency (fn) Audio 3dB BW Audio Output (at fn) (kHz) (kHz) (mV) (%) Distortion (%) IC IC Maker Type TOSHIBA SMD CDBKB450KCAY79-R0 450 fn±3.0 min. 145 ±40 - - TB32302FG CDBKB455KCAY07-R0 455 fn±4.0 min. 350 ±60 3.0 max. - MC3357 CDBKB455KCAY09-R0 455 fn±4.0 min. 120 ±40 1.5 max. - NE604N PHILIPS SMD CDBKB455KCAY13-R0 455 fn±4.0 min. 330 ±50 4.0 max. - CXA1003BM SONY SMD CDBKB455KCAY16-R0 455 fn±4.0 min. 175 ±40 2.0 max. - MC3372 CDBKB455KCAY24-R0 455 fn±4.0 min. 100 ±40 2.0 max. - TA31136 TOSHIBA SMD CDBKB455KCAY27-R0 455 fn±4.0 min. 90 ±30 2.0 max. - TK10487 TOKO SMD CDBKB455KCAY28-R0 455 fn±4.0 min. 40 ±20 3.0 max. - TA31142F TOSHIBA SMD CDBKB455KCAY29-R0 455 fn±4.0 min. 100 ±30 2.5 max. - NE605 PHILIPS SMD CDBKB455KCAY35-R0 455 fn±4.0 min. 100 ±40 2.5 max. - TK10930 TOKO SMD CDBKB455KCAY40-R0 455 fn±4.0 min. 40 ±20 3.5 max. - TA31145 TOSHIBA SMD CDBKB455KCAY49-R0 455 fn±4.0 min. 45 ±10 3.0 max. - MC3361 CDBKB455KCAY50-R0 455 fn±4.0 min. 64 ±6.4 4.0 max. - CXA3117N SONY SMD CDBKB455KCAY66-R0 455 fn±4.2 min. 40 ±10 4.0 max. - NJM2590 JRC SMD CDBKB455KCLX36-R0 455 fn±13.0 min. 90 ±30 2.5 max. 5.0 max. NE(SA)606/NE(SA)616 [within fn ±6kHz] PHILIPS SMD CDBKB455KCLX39-R0 455 fn±11.0 min. 130 ±20 2.5 max. 7.0 max. [within fn ±8kHz] NE607/NE617 PHILIPS SMD CDBKB455KCLY13-R0 455 fn±13.0 min. 120 ±30 1.5 max. 5.0 max. [within fn ±8kHz] CXA1003BM SONY SMD CDBLB455KCAY07-B0 455 fn±4.0 min. 340 ±60 3.0 max. - MC3357 CDBLB455KCAY13A-B0 455 fn±4.0 min. 350 ±50 3.0 max. - CXA1003BM SONY Lead CDBLB455KCAY24-B0 455 fn±4.0 min. 100 ±40 2.0 max. - TA31136 TOSHIBA Lead CDBLB455KCAY28-B0 455 fn±4.0 min. 40 ±20 3.0 max. - TA31142FN TOSHIBA Lead CDBLB455KCAY34-B0 455 fn±4.0 min. 65 ±20 2.5 max. - MC13136 CDBLB455KCAY40-B0 455 fn±4.0 min. 40 ±20 3.0 max. - TA31145 TOSHIBA Lead CDBLB455KCAY42-B0 455 fn±4.0 min. 40 ±15 3.0 max. - TK14590/TK14591 TOKO Lead CDBLB455KCAY49-B0 455 fn±4.0 min. 45 ±10 3.0 max. - MC3361 CDBLB455KCAY50-B0 455 fn±4.0 min. 64 ±6.4 4.0 max. - CXA3117N SONY Lead CDBLB455KCLY09-B0 455 fn±15.0 min. 70 ±20 1.5 max. 3.5 max. [within fn ±8kHz] NE604N PHILIPS Lead MOTOROLA SMD MOTOROLA SMD MOTOROLA SMD MOTOROLA Lead MOTOROLA Lead MOTOROLA Lead Continued on the following page. 55 17 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Continued from the preceding page. Nominal Center Recovered Recovered Distortion Frequency (fn) Audio 3dB BW Audio Output (at fn) (kHz) (kHz) (mV) (%) Part Number Distortion (%) IC IC Maker Type SONY Lead CDBLB455KCLY13-B0 455 fn±15.0 min. 110 ±30 1.5 max. 5.0 max. [within fn ±8kHz] CXA1003BM CDBLB455KCAX16-B0 455 fn±4.0 min. 185 ±40 2.0 max. - MC3372 MOTOROLA Lead CDBLB455KCAX18-B0 455 fn±3.0 min. 180 ±40 2.0 max. - MC3371 MOTOROLA Lead CDBLB455KCAX36-B0 455 fn±3.5 min. 100 ±25 3.5 max. - NE606/NE616 PHILIPS Lead For safety purposes, avoid applying a direct current between the terminals. The order quantity should be an integral multiple of the "Minimum Quantity" shown in package page in this catalog. c Test Circuit MC3357 NE604N 8.2k IF input AF output 15 14 1 2 3 13 12 11 10 9 6 0.1μ 7 8 0.1μ MC3357 4 5 0.022μ 16 10μ + 15 14 13 47k 12 0.1μ 11 10 9 6 7 8 NE604 C 50 Vcc FM S. S. G. (Rg = 50Ω) 0.01μ 0.01μ 16 0.1μ 10k 1 X 2 3 4 C 5 R 0.1μ X Vcc Unit C: F R: Ω 100p 1000p Part Number (X) C R CDBLB455KCAY07-B0 150pF 1.5kΩ CDBKB455KCAY07-R0 150pF 1.3kΩ Part Number (X) C R L – CDBKB455KCAY09-R0 120pF 1.8kΩ CDBLB455KCLY09-B0 120pF 560Ω 220μH CXA1003BM R L 100p + 47μ 0.01μ AF output Unit C: F R: Ω MC3372 IF input L 0.01μ 0.01μ 0.01μ 0.01μ 0.01μ X 0.01μ 23 22 21 20 19 18 17 16 15 14 16 15 14 5 6 7 0.01μ 8 9 10 11 12 0.01μ 2 3 4 11 10 Vcc 51k 68p 1.8k 220p 0.1μ Unit C: F R: Ω C R CDBLB455KCAX16-B0 27pF 4.3kΩ CDBKB455KCAY16-R0 100pF 1.0kΩ TA31136 + 10μ 0.1μ 510k X C 8.2k R 1μ + AF output AF output 0.01μ 13 12 11 10 Vcc (+2.0V) 3 Vcc 68p 220p 4 5 6 0.1μ 2 1 2 3 13 12 11 10 9 6 7 8 0.01μ 9 MC3371 1 14 7 8 X Test condition Vcc = +4.0V R = 6.2kΩ X: CDBLB455KCAX18-B0 TA31136F + 10μ 4 5 0.1μ 14 15 0.01μ 15 16 0.1μ 16 17 Part Number (X) FM S. S. G 51k Unit C: F R: Ω R (Rg = 50Ω) RF input 0.01μ X 0.01μ AF output Vcc MC3371 51 9 5 6 7 8 0.1μ 51k C 12 100μ 100μ Part Number (X) C R L CDBLB455KCAY13A-B0 82pF 1.2kΩ – – CDBKB455KCAY13-R0 82pF 1.0kΩ CDBLB455KCLY13-B0 82pF 560Ω 220μH CDBKB455KCLY13-R0 13 MC3372 2700p 4 0.01μ 3 AF output 13 1 2 8.2k 0.01μ CXA1003BM 1 510k 51k 0.01μ C 24 0.1μ 51 R Unit C: F R: Ω R 0.1μ IF input 0.01μ IF input Unit C: F R: Ω Part Number (X) C R CDBLB455KCAY24-B0 91pF 1.5kΩ CDBKB455KCAY24-R0 91pF 1.2kΩ Continued on the following page. 56 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Continued from the preceding page. c Test Circuit TK10487 TA31142 8.2k 17 1 2 3 4 16 15 14 13 12 11 7 8 9 10 C 20 TK10487 Vcc X 0.01μ Vcc 19 1 18 2 17 3 + 10μ R 16 4 15 + 10μ Part Number (X) C R CDBKB455KCAY27-R0 33pF 1.0kΩ 5 0.1μ Unit C: F R: Ω 2k 0.01μ 68k 68k 3300p 14 13 12 11 8 9 10 TA31142F 0.1μ 6 0.1μ 5 560p 0.01μ 68k 6 7 AF output + 0.1μ 18 10μ 19 2SC1048 0.01μ 20 Vcc 2.2μ + 430 0.01μ Vcc 0.01μ C X + 10μ IF input NE605 Unit C: F R: Ω R Part Number (X) C R CDBLB455KCAY28-B0 22pF 3.3kΩ CDBKB455KCAY28-R0 22pF 2.7kΩ MC13136 IF input AF input 0.01μ 0.1μ 0.1μ 20 19 18 17 16 15 14 13 12 X 0.15μ 1k R C 11 24 NE605 23 22 21 20 19 18 17 16 15 14 13 8 9 10 11 12 C MC13136 5 6 7 8 + 22μ 100k 0.1μ 9 100k 22k 10 1 Vcc 2 3 4 5 6 7 0.1μ 4 X R 0.01μ 3 100k 150p 2 5n 1 0.1μ Vcc + 0.1μ 0.01μ 0.1μ 0.1μ 0.1μ Part Number (X) CDBKB455KCAY29-R0 C R 56pF 2.2kΩ Unit C: F R: Ω AF output IF input Part Number (X) C R CDBLB455KCAY34-B0 100pF 1.2kΩ TK10930 Unit C: F R: Ω NE(SA)606/616 IF input TK10930 Vcc 9 C 20 19 18 1 2 3 R2 8.2k 0.01μ Vcc 0.1μ 0.1μ IF input R1 C CDBKB455KCAY35-R0 16 15 2 3 4 5 6 22pF 4.7kΩ – CDBKB455KCLX36-R0 27pF 2.2kΩ 1mH 14 13 12 11 + 2.2μ 7 8 C 9 +10μ 1.5k 8.2k 0.01μ 0.01μ 7 8 9 10 C 20k + X 2.2μ L 2k 8.2k R 0.1μ AF output Unit C: F R: Ω 0.1μ 0.1μ 430 20 19 10 17 1 X L 2 3 4 + 10μ R C R L CDBKB455KCLX39-R0 22pF 2.7kΩ 1mH 15 14 13 12 11 5 6 9 10 0.01μ 68k 7 8 + X 0.1μ AF output Part Number (X) 16 R + 0.1μ 0.1μ 18 3300p TA31145 (TOSHIBA) 22k Vcc 11 TA31145 NE607/617 (PHILIPS) 1 12 L 100k 17 13 0.1μ CDBLB455KCAX36-B0 1.0kΩ 100k 18 0.1μ R 0.1μ 19 6 C 0.1μ 20 14 Vcc 0.01μ 51 5 Part Number (X) NE(SA)607/617 IF input 15 R2 2.0kΩ 33pF 16 4 + 2.2μ Unit C: F R: Ω Part Number (X) 17 NE606 or NE616 X R1 + 10μ AF output 10 11 12 0.1μ IF input Unit C: F R: Ω L: H AF output 5600p 8 68k 7 68k 6 1000p 5 560p 4 10μ 3 0.1μ 2 0.1μ 1 0.01μ 0.1μ 24 23 22 21 20 19 18 17 16 15 14 13 17 Unit C: F R: Ω Part Number (X) R CDBLB455KCAY40-B0 3.3kΩ CDBKB455KCAY40-R0 2.7kΩ Continued on the following page. 57 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Continued from the preceding page. c Test Circuit TK14590/14591 MC3361 Vcc (1.3V) AF output 0.01μ 100k 1μ 100k 0.01μ 100p 0.15μ 0.1μ 1000p 0.1μ 24 23 22 21 20 19 18 17 16 15 14 13 16 TK14590V (TOKO) 5 6 0.1μ 7 8 X IF input 1k 14 13 12 11 10 9 6 8 MC3361 1 2 3 4 5 7 0.01μ Unit C: F R: Ω 560p 100k 0.0033μ R 15 AF output 8.2k 9 10 11 12 C 100k 4 0.01μ 100k 3 0.1μ 2 0.1μ 1 100k 150k Vcc 0.1μ 0.1μ 22 47μ 0.01μ 1μ X 0.1μ 0.022μ Part Number (X) C R CDBLB455KCAY42-B0 22pF 3.3kΩ IF input CXA3117 Unit C: F R: Ω R Part Number (X) R CDBLB455KCAY49-B0 1.8kΩ CDBKB455KCAY49-R0 1.5kΩ NJM2590 Vcc + 100k AF out 24 23 22 21 20 19 18 17 16 15 14 13 100k 10μ 14 13 12 11 10 9 8 CXA3117(SONY) 1 2 3 4 5 6 7 8 1μ Vcc X 33μ 1200p NJM2590(JRC) 9 10 11 12 1 1200p 1200p Unit C: F R: Ω R 0.01μ Part Number (X) R CDBLB455KCAY50-B0 8.2kΩ CDBKB455KCAY50-R0 6.2kΩ S.G. 2 5 4 3 6 0.1μ 0.1μ 10k R 51 7 X + 10μ Unit C: F R: Ω 0.01μ Part Number (X) R CDBKB455KCAY66-R0 3.0kΩ AF output c Recovered Audio Curve 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 5 0.5 1 0.1 10 1.0 5 0.5 1 0.1 440 450 460 Frequency (kHz) 470 AF Output Voltage (mV) 500 440 450 460 T.H.D. (%) CDBLB455KCAY07-B0 T.H.D. (%) AF Output Voltage (mV) CDBKB455KCAY07-R0 470 Frequency (kHz) Continued on the following page. 17 58 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Continued from the preceding page. c Recovered Audio Curve 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 460 470 395 Frequency (kHz) 515 CDBKB455KCLY13-R0 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 440 450 460 AF Output Voltage (mV) 500 T.H.D. (%) AF Output Voltage (mV) 475 Frequency (kHz) CDBKB455KCAY13-R0 470 425 Frequency (kHz) 465 485 CDBLB455KCLY13-B0 500 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 AF Output Voltage (mV) 50.0 T.H.D. (%) 500 445 Frequency (kHz) CDBLB455KCAY13A-B0 AF Output Voltage (mV) 435 T.H.D. (%) 450 50.0 T.H.D. (%) 440 AF Output Voltage (mV) 500 T.H.D. (%) CDBLB455KCLY09-B0 T.H.D. (%) AF Output Voltage (mV) CDBKB455KCAY09-R0 17 440 450 460 Frequency (kHz) 470 395 435 475 515 Frequency (kHz) Continued on the following page. 59 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Continued from the preceding page. c Recovered Audio Curve 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 460 470 440 Frequency (kHz) 470 CDBKB455KCAY24-R0 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 440 450 460 AF Output Voltage (mV) 500 T.H.D. (%) AF Output Voltage (mV) 460 Frequency (kHz) CDBLB455KCAX18-B0 470 440 Frequency (kHz) 450 460 470 Frequency (kHz) CDBLB455KCAY24-B0 CDBKB455KCAY27-R0 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 AF Output Voltage (mV) 500 T.H.D. (%) AF Output Voltage (mV) 450 T.H.D. (%) 450 T.H.D. (%) 440 AF Output Voltage (mV) 500 T.H.D. (%) CDBLB455KCAX16-B0 T.H.D. (%) AF Output Voltage (mV) CDBKB455KCAY16-R0 17 440 450 460 Frequency (kHz) 470 440 450 460 470 Frequency (kHz) Continued on the following page. 60 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Continued from the preceding page. c Recovered Audio Curve 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 460 470 440 450 Frequency (kHz) 470 CDBLB455KCAY34-B0 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 440 450 460 AF Output Voltage (mV) 500 T.H.D. (%) AF Output Voltage (mV) CDBKB455KCAY29-R0 470 440 450 Frequency (kHz) 10.0 50 5.0 10 1.0 5 0.5 1 0.1 460 Frequency (kHz) 470 10 100 AF Output Voltage (mV) 100 50 500 T.H.D. (%) 50.0 450 470 CDBKB455KCLX36-R0 500 440 460 Frequency (kHz) CDBKB455KCAY35-R0 AF Output Voltage (mV) 460 Frequency (kHz) T.H.D. (%) 450 5 50 1 10 5 0.5 1 0.1 425 445 465 T.H.D. (%) 440 AF Output Voltage (mV) 500 T.H.D. (%) CDBLB455KCAY28-B0 T.H.D. (%) AF Output Voltage (mV) CDBKB455KCAY28-R0 17 486 Frequency (kHz) Continued on the following page. 61 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Continued from the preceding page. c Recovered Audio Curve 50.0 100 10.0 50 5.0 10 1.0 5 0.5 1 0.1 500 50.0 100 10.0 50 5.0 10 1.0 5 0.5 1 0.1 425 460 470 CDBKB455KCAY40-R0 485 CDBLB455KCAY40-B0 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 440 450 460 AF Output Voltage (mV) 500 T.H.D. (%) AF Output Voltage (mV) 465 Frequency (kHz) Frequency (kHz) 470 440 Frequency (kHz) 10.0 50 5.0 10 1.0 5 0.5 1 0.1 17 AF Output Voltage (mV) 100 T.H.D. (%) 50.0 460 Frequency (kHz) 470 500 50.0 100 10.0 50 5.0 10 1.0 5 0.5 1 0.1 440 450 460 CDBKB455KCAY49-R0 500 440 450 Frequency (kHz) CDBLB455KCAY42-B0 AF Output Voltage (mV) 445 T.H.D. (%) 450 470 450 460 T.H.D. (%) 440 T.H.D. (%) 500 AF Output Voltage (mV) CDBKB455KCLX39-R0 T.H.D. (%) AF Output Voltage (mV) CDBLB455KCAX36-B0 470 Frequency (kHz) Continued on the following page. 62 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Continued from the preceding page. c Recovered Audio Curve 50.0 500 50.0 100 10.0 100 10.0 50 5.0 50 5.0 10 1.0 10 1.0 5 0.5 5 0.5 1 0.1 1 0.1 450 460 470 440 Frequency (kHz) 100 10.0 50 5.0 10 1.0 5 0.5 1 0.1 460 AF Output Voltage (mV) 50.0 T.H.D. (%) AF Output Voltage (mV) 470 CDBKB455KCAY66-R0 500 450 460 Frequency (kHz) CDBLB455KCAY50-B0 440 450 500 50.0 100 10.0 50 5.0 10 1.0 5 0.5 1 0.1 440 470 450 460 T.H.D. (%) 440 AF Output Voltage (mV) 500 T.H.D. (%) CDBKB455KCAY50-R0 T.H.D. (%) AF Output Voltage (mV) CDBLB455KCAY49-B0 470 Frequency (kHz) Frequency (kHz) Specified by S Curve Characteristics Part Number CDBKB455KCAY54-R0 Nominal Center Frequency (fn) (kHz) S Curve (1) Output Volt. at fn (mV) S Curve (2) at fn±4.8kHz (mV) IC IC Maker Type 455 165 ±20 170 ±20 TA31149 TOSHIBA SMD 17 63 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. c Test Circuit c S Curve TA31149 CDBKB455KCAY54-R0 24 23 22 21 10μ + 100k 430 20 19 1000p Vcc Vcc Vcc 100k + 0.4 100k 2.2μ Vcc (+1.4V) 18 17 16 15 14 13 0.3 TA31149(TOSHIBA) IF input 8 9 10 11 12 X R 0.1μ Volt (V) 7 + AF output 6 1000p 5 1200p 4 1500p 3 10μ 2 0.1μ 1 0.2 Unit C: F R: Ω Part Number (X) R CDBKB455KCAY54-R0 2.7kΩ 0.1 0.0 440 450 460 Frequency (kHz) 17 64 470 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Discriminators for Communications Equipment 0.3±0.2 MHz Type Ceramic Discriminators 0.2±0.2 0.4±0.05 1.0 max. 4.1 max. 0.4(ref.) c Features 0.4(ref.) 0.8±0.1 1. Compact and high reliability and recommended for automotive applications. 2. Can be combined with various ICs. The IC is determined by the last number in the part number. 3. Stable demodulation characteristics can be obtained without adjustment. 4. Stable temperature characteristics 5. Available lead (Pb) free solder reflow. 1.4 max. 4.5±0.1 2.0±0.1 CDSCB10M7 series forms a resonator on a piezoelectric ceramic substrate. In combination with ICs, this type obtains stable demodulation characteristics in a wide bandwidth. They have 1.0mm max. thickness and small mounting area (4.5x2.0mm). 0.8±0.1 CDSCB Series 1.5±0.1 1.5±0.1 (in mm) Center Frequency (fo) (MHz) Recovered Audio 3dB BW (kHz) Recovered Audio Output (mV) Distortion (%) S Curve (mV) IC CDSCB10M7GA105A-R0 10.700 ±30kHz 220 min. 110 min. 1.5 max. - TEA5757HL CDSCB10M7GA113-R0 10.700 ±30kHz 300 min. 110 min. 1.0 max. - TA2154FN CDSCB10M7GA119-R0 10.700 ±30kHz 500 min. 75 min. 1.0 max. - TRF6901 CDSCB10M7GA121-R0 10.700 ±30kHz 390 min. 80 min. 1.0 max. - LV23100V CDSCB10M7GA135-R0 10.700 ±30kHz 155 min. 75 min. - - TH71101 CDSCB10M7GA136-R0 10.700 ±30kHz 140 min. 120 min. - - TH7122 CDSCB10M7GF072-R0 10.700 (fn) fn±150 min. 130 min. 2.0 max. - TA31161 CDSCB10M7GF107S-R0 10.700 (fn) fn±80 min. 52 min. 3.0 max. - TA31272FN CDSCB10M7GF109-R0 10.700 (fn) fn±100 min. 170 min. 3.0 max. - TK14588V CDSCB10M7GF123-R0 10.700 (fn) - - - 900 min. TA31275FN CDSCB10M7GF123S-R0 10.700 (fn) - - - 900 min. TA31275FN CDSCB10M7GF126-R0 10.700 (fn) - - - 400 min. NJM2295AV Part Number (fn) means nominal center frequency. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. For safety purposes, avoid applying a direct current between the terminals. 18 65 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 c Test Circuit CDSCB10M7GA105A-R0 CDSCB10M7GA113-R0 Vcc (1.2V) 35 3 34 4 33 5 32 6 31 TEA5757HL (PHILIPS) 7 100k 29 28 0.01μ 27 26 25 8 29 9 28 10 27 11 26 24 23 22 21 20 19 18 17 16 11 12 13 14 15 TA2154FN (TOSHIBA) 1 2 3 4 5 6 7 8 9 10 + X 30 12 DC OUT 30 S.S.G. 2.2μ 680p 2 0.01μ + 100μ 0.01μ 10μ + 48 47 46 45 44 43 42 41 40 39 38 37 0.1μ 1 36 0.01μ 0.1μ 0.01μ Vcc (3.0V) D.C. OUT AF OUT X: CDSCB10M7GA113-R0 Unit C: F R: Ω S.S.G. 10 25 0.47μ 0.1μ + X AFC (n) 0.22μ 150 AF OUT X: CDSCB10M7GA105A-R0 Unit C: F R: Ω CDSCB10M7GA119-R0 CDSCB10M7GA121-R0 Vcc (3.0V) IF Input 4.7μ 10p 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 LV23100V (SANYO) 35 3 34 32 6 TRF6901 31 7 (TEXAS INSTRUMENTS) 30 8 29 9 28 4 5 + 11 26 12 25 13 14 15 16 17 18 19 20 21 22 23 24 0.01μ 7 8 0.047μ 9 10 11 12 13 14 15 16 17 18 + 47p + 0.47μ 0.01μ 27 100p 10 6 10k 5 3 10k 10μ 1000p 33 4 2 X 2 1 X 1μ 48 47 46 45 44 43 42 41 40 39 38 37 36 3.3k 0.1μ + 1μ 0.22μ 0.47μ 0.047μ + S.G. 100p 10k 100μ 1 75 0.01μ 0.015μ 22μ+ 82p 10 + PIC16F84 (Control IC) PIC16F84 1 2 3 4 5 1k 6 7 1 8 2 3 4 5 6 7 8 9 9 X: CDSCB10M7GA119-R0 Unit C : F R: Ω L: H 10k + 2.2μ 10k 18 17 16 15 14 13 12 11 10 18 17 16 15 14 13 12 11 10 0.1μ 1k 2.2μ X: CDSCB10M7GA121-R0 CDSCB10M7GA135-R0 + 10k 0.1μ Unit C: F R: Ω CDSCB10M7GA136-R0 Vcc (5.0V) Vcc (5.0V) AF-OUT FKS-OUT 330p 0.1μ 0.1μ 24 23 22 21 20 19 18 17 25 16 26 100p 1000p 0.01μ 0.01μ 330k 15 27 28 220k 29 14 TH7122 [Internal AFC Enabled] (MELEXIS) 30 0.01μ 24 23 22 21 20 19 18 17 25 26 15 27 14 31 10 12p C.D. 29 0.01μ 0.01μ 2 3 4 5 6 7 8 0.1μ FKS-OUT 330p AF-OUT 330p 13 100k 0.033μ 12 S.G. 1000p 30 330p 0.01μ 9 1 1000p TH71101, TH71102, TH71111 or TH71112 (MELEXIS) 28 12 32 16 330p 13 11 0.01μ 11 C.D. 3.3k 0.01μ 31 10 330p 0.01μ 32 9 1 2 3 4 5 6 7 100k 8 18 0.01μ 18 10p 220k 15p 120p Vcc (3.2V) 0.01μ 0.047μ 0.01μ D.C. Output AF Output 68p 0.01μ 0.01μ AF Output 100p 4.7μ AFC (p) 330p 0.1μ 13 14 15 16 17 18 19 20 21 22 23 24 S.G. X: CDSCB10M7GA135-R0 330p Unit C: F R: Ω 16 15 100p 14 13 12 11 10 PIC16F84 (Control IC) 1 + 10μ 17 2 3 4 5 6 1k 7 10k + 2.2μ 8 9 X: CDSCB10M7GA136-R0 0.1μ Unit C: F R: Ω Continued on the following page. 66 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Continued from the preceding page. c Test Circuit CDSCB10M7GF072-R0 CDSCB10M7GF107S-R0 Vcc (5.0V) Vcc (3V) AF Output 24 2 13 20 19 18 1 12 11 10 2 3 4 5 6 7 9 X: CDSCB10M7GF072-R0 R: 820 Unit C: F R: Ω L: H + 13 0.01μ IF IN 10 11 12 C.D.: Ceramic Discriminator Unit R: Ω C: F L: H CDSCB10M7GF123-R0 Vcc (5.0V) 0.01μ AF OUT 1000p 1.2μ R 24 X D.C. OUT 1 12 10 9 7 8 20 19 2 3 4 5 18 6 0.01μ 0.01μ 11 0.1μ 13 21 17 16 15 14 13 10 11 12 TA31275FN (TOSHIBA) 8p 51k 22 AF OUT 0.01μ 1000p 23 0.01μ DC-OUT 3300p Vcc (3V) 14 C.D. 0.01μ S.S.G. CDSCB10M7GF109-R0 12k 9 7 8 9 0.1μ 33μ 15 14 0.01μ 0.01μ 16 15 8 0.1μ 7 0.1μ 6 8 0.01μ 5 0.01μ 4 0.01μ 16 0.01μ TA31161 (TOSHIBA) 3 17 1.2k 1 14 21 0.01μ 15 22 TA31272FN (TOSHIBA) 10p 16 23 X 1000p R 0.01μ 1.8k AF OUT 0.01μ 0.01μ 100μ + 4.7μ 0.01μ 0.01μ 4 5 6 + S.S.G. 4.7μ 3 S.S.G. X: CDSCB10M7GF123-R0 Unit C: F R: Ω 0.01μ 2 0.01μ 0.01μ 1 51 0.01μ TK14588V (TOKO) X: CDSCB10M7GF109-R0 R: 820 Unit C: F R: Ω L: H CDSCB10M7GF126-R0 DC-OUT 20 100p 0.01μ + 0.01μ 19 18 17 16 15 14 13 12 8 9 11 NJM2295AV (JRC) 4 5 6 7 + 10μ 10 8p C.D. 180 10μ+ 3 0.01μ 2 0.01μ 1 10μ+ 10μ Vcc (5.0V) X: CDSCB10M7GF126-R0 S.G. Unit C: F R: Ω 18 67 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 c Recovered Audio Curve CDSCB10M7GA105A-R0 1000 CDSCB10M7GA113-R0 100 1000 10 100 100 AF Output 1 1 10 Distortion 10 1 1 0.1 T.H.D. (%) 10 T.H.D. (%) AF Output Voltage (mV) Distortion AF Output Voltage (mV) AF Output 100 0.1 Input = 100dBμ fdev. = ±75kHz fmod. = 1kHz Vcc = 3.0V 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 Frequency (MHz) 10.6 CDSCB10M7GA119-R0 1000 10.8 10.9 11.0 11.1 CDSCB10M7GA121-R0 100 1000 10 100 100 AF Output 1 1 T.H.D. (%) Distortion 10 AF Output Voltage (mV) AF Output 100 AF Output Voltage (mV) 10.7 Frequency (MHz) 10 Distortion 10 1 1 0.1 0.1 Input = 100dBμ fdev. = ±75kHz fmod. = 1kHz Vcc = 3.2V Input = 100dBμ fdev. = ±60kHz fmod. = 1kHz Vcc = 3.0V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 10.3 11.1 10.4 10.6 10.7 10.8 10.9 11.0 11.1 CDSCB10M7GA136-R0 1000 100 100 AF Output Voltage (mV) AF Output Voltage (mV) CDSCB10M7GA135-R0 1000 10 1 0.1 10.4 10.5 Frequency (MHz) Frequency (MHz) 18 T.H.D. (%) 10.3 Input = 100dBμ fdev. = ±75kHz fmod. = 1kHz Vcc = 1.2V 10 1 Input = 100dBμ fdev. = ±50kHz fmod. = 1kHz Vcc = 5.0V 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 11.0 0.1 10.4 Input = 100dBμ fdev. = ±50kHz fmod. = 1kHz Vcc = 5.0V 10.5 10.6 10.7 10.8 10.9 11.0 Frequency (MHz) Continued on the following page. 68 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Continued from the preceding page. c Recovered Audio Curve CDSCB10M7GF072-R0 CDSCB10M7GF109-R0 100 10 100 10 10 1 10 1 1 0.1 0.1 1 Input = 100dBμ fdev. = ±80kHz fmod. = 1kHz Vcc = 3.0V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 T.H.D. (%) 100 AF Output Voltage (mV) 1000 T.H.D. (%) 100 AF Output Voltage (mV) 1000 Input = 100dBμ fdev. = ±64kHz fmod. = 1kHz Vcc = 3.0V 11.1 10.3 10.4 10.5 Frequency (MHz) 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) c S Curve CDSCB10M7GF123-R0 CDSCB10M7GF126-R0 4.0 2.5 2.0 3.0 Volt (V) Volt (V) 1.5 1.0 2.0 0.5 0.0 10.3 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 11.0 11.1 1.0 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) 18 69 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Ceramic Discriminators Notice c CDBKB Series Notice (Soldering and Mounting) 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Peak (260°C max.) Temperature (°C) 260 230 Heating (230°C) Pre-heating 100 (150-180°C) 30 sec. min. 60-120 sec. Gradual Cooling 40 sec. max. 120 sec. min. (2) Soldering Iron Electrode is directly soldered with the tip of soldering iron at +350±5°C for 3.0±0.5 seconds. 2. Wash (1) Cleaning Solvent CFC alternatives (HCFC Series), Isopropyl Alcohol (IPA), Water (Demineralized Water), Cleaning Water Solution (Cleanthrough-750H, Pine Alpha 100S), Silicon (Technocare FRW) (2) Cleaning Conditions o Immersion Wash 2 minutes max. in above solvent at +60°C max. o Shower or Rinse Wash 2 minutes max. in above solvent at +60°C max. (3) Notice o When components are immersed in solvent, be sure to maintain the temperature of components below the temperature of solvent. o Please do not use ultrasonic cleaning. o Total washing time should be within 4 minutes. o Please ensure the component is thoroughly evaluated in your application circuit. o Please do not use chlorine, petroleum or alkaline cleaning solvents. o If you plan to use any other type of solvents, please consult with Murata or Murata representative prior to using. c CDBKB Series Notice (Handling) 1. The component will be damaged when an excessive stress is applied. 2. If the component is cleaned, please confirm that the reliability has not been degraded. 3. In case of covering filter with over coating, conditions such as material of resin, cure temperature, and so on should be evaluated carefully. 4. Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. 5. The product, packed in a moisture-proof bag (dry pack), is sensitive to moisture. The following treatment is required before applying reflow soldering, to avoid package cracks or reliability degradation caused by thermal stress. When unpacked, store the component in an atmosphere of below 25 degrees C. and below 65%R.H., and solder within 48 hours. Continued on the following page. 70 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Discriminators Notice Continued from the preceding page. c CDBLB Series Notice (Handling) 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. The component will be damaged when an excessive stress is applied. 3. No type of reflow soldering should be applied to this component. 4. Do not clean or wash the component as it is not hermetically sealed. 5. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 6. In case of covering discriminator with over coating, conditions such as material of resin, cure temperature, and so on should be evaluated carefully. 71 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Ceramic Discriminators Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (°C) c CDSCB Series Notice o Soldering and Mounting Peak (260°C max.) 260 230 Pre-heating (150-180°C) 100 Heating (230°C) Gradual Cooling 30 sec. min. 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +300±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Condition for Placement Machines The component is recommended with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent the electrode erosion. [Component Direction] Place the component laterally to the direction in which stress acts. [Component Layout Close to Board] Perforation B A Slit C Susceptibility to stress is in the order of : A>C>B Continued on the following page. 72 P05E.pdf Nov.24,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Discriminators Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40°C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality and/or be degraded in solderability due to storage under poor condition. (5) Please do not drop the products to avoid cracking of ceramic element. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, avoid applying a direct current between the terminals. 73 P05E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Nov.24,2011 Ceramic Discriminators Standard Land Pattern Dimensions/Packaging c Standard Land Pattern Dimensions CDBKB Series 2.6 3.0 1.2 4.9 2.6 2.0 1.2 CDSCB Series 1.0 2.0 1.0 (in mm) (in mm) c Minimum Quantity Part Number Taping ø180mm Bulk 500 CDBKB Series CDBLB Series 500 CDSCB Series 2000 (pcs.) The order quantity should be an integral multiple of the "Minimum Quantity" shown above. c CDBKB Series Dimensions of Carrier Tape 1.75±0.1 8.0±0.1 3° max. User direction of feed Cover film (ø180 +0 -3.0) (ø60 +1.0 -0 ) Empty 7.2±0.1 ø1.5 +0.1 -0.0 7.5±0.1 2.0±0.1 Trailer 160 to 190 16.0±0.15 4.0±0.1 Dimensions of Reel Leader Cover film Components 2.0±0.2 ø13.0±0.5 Empty 160 to 200 400 to 560 3.3±0.1 17.0±0.3 19.4±1.0 6.3±0.1 s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP (in mm) Continued on the following page. 74 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011 Ceramic Discriminators Standard Land Pattern Dimensions/Packaging Continued from the preceding page. c CDSCB Series $IMENSIONS OF #ARRIER 4APE ø1.5 2.0±0.05 1.75±0.1 4.0±0.1 Dimension of reel +0.1 -0 4RAILER 160 to 190 ,EADER Cover film 10° Cover film (3°) User direction of feed s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP 400 to 560 180 +0.1 -1.5 +0.1 60 -0 12.0±0.2 ø13.0±0.2 %MPTY 240 to 280 2.0±0.5 MAX 2.2±0.1 1.1±0.1 4.7±0.1 +0.1 ø1.5 -0 0.3±0.05 (9.0) 4.0±0.1 0EELING STRENGTH 0.1 to 0.7N 5.5±0.05 %MPTY #OMPONENTS +1.0 13.0 -0 17.0±1.0 ( ): Reference (in mm) 75 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P05E.pdf Nov.24,2011