Ordering number : ENA1802 Bi-CMOS integrated circuit LV8548M 12V Low Saturation Voltage Drive Forward/Reverse Motor Driver Overview The LV8548M is a 2-channel low saturation voltage forward/reverse motor driver IC. It is optimal for motor drive in 12V system products and can drive either two DC motors, one DC motor using parallel connection, or a 2-phase bipolar stepping motor with 1-2 phase excitation mode drive. Functions • DMOS output transistor adoption (Upper and lower total RON=1Ω typ) • For one power supply (The control system power supply is unnecessary.) • Our motor driver IC, LB1948M, and compatible pin • It is possible to connect it in parallel (parallel, connected operation of drive ch). • The compact package (MFP-10S) is adopted. • VCC max=20v, IO max=1A • Current consumption 0 when standing by • Built-in brake function Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum power supply voltage VCC max -0.3 to +20 Output impression voltage VOUT -0.3 to +20 V V Input impression voltage VIN -0.3 to +6 V GND pin outflow current IGND For ch Allowable Power dissipation Pd max * Operating temperature Storage temperature 1.0 A 1.05 W Topr -30 to +85 °C Tstg -40 to +150 °C *: When mounted on the specified printed circuit board (57.0mm ×57.0mm × 1.6mm), glass epoxy, both sides Recommended Operating Range at Ta = 25°C Parameter Power supply voltage Symbol Conditions Ratings Unit VCC 4.0 to 16 V Input “H” level voltage VINH +1.8 to +5.5 V Input “L” level voltage VINL -0.3 to +0.7 V Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 70710 SY 20100625-S00003 No.A1802-1/6 LV8548M Electrical Characteristics at Ta = 25°C, VCC = 12V Parameter Symbol Power supply voltage ICC0 Ratings Conditions min typ Unit max Standby mode 1 μA 2.3 mA IN1=IN2=IN3=IN4=”LOW” ICC1 It is "High" from IN1 as for either of IN4. Load opening Input current IIN VIN=5V Thermal shutdown operating Ttsd Design certification Width of temperature hysteria ΔTtsd Design certification Low voltage protection function VthVCC 1.7 35 50 65 μA 150 180 210 °C temperature °C 40 3.3 3.5 3.65 V 3.55 3.8 3.95 V 0.7 1 1.25 Ω 10 μA 1.2 V operation voltage Release voltage Vthret Output ON resistance RON IOUT=1.0A Output leak current IOleak VO=16V Diode forward voltage VD ID=1.0A (Upper and lower total) 1.0 Package Dimensions unit : mm (typ) 3086B 4.4 6.4 6 0.15 0.1 (1.5) 1.7max 5 1 Allowable power dissipation, Pd max -- W 0.63 10 0.35 Pd max - Ta 1.5 5.0 1.0 (0.5) SANYO : MFP10S(225mil) 1.05 1.0 0.55 0.5 0 -20 0 20 40 60 80 100 Ambient temperature, Ta -- C Pin Assignment 10 OUT1 IN1 2 9 OUT2 IN2 3 IN3 4 IN4 5 LV8548M VCC 1 8 OUT3 7 OUT4 6 GND No.A1802-2/6 LV8548M Block Diagram 1. At two DC motor drive VCC H-side PRE LVS OUT1 IN1 OUT2 IN2 INPUT LOGIC M L-side PRE IN3 VCC H-side PRE IN4 OUT3 OUT4 M L-side PRE VREF TSD GND 2. At one stepping motor drive VCC H-side PRE LVS OUT1 IN1 OUT2 IN2 INPUT LOGIC L-side PRE IN3 VCC H-side PRE IN4 OUT3 OUT4 M L-side PRE TSD VREF GND No.A1802-3/6 LV8548M Pin function Pin No. 1 Pin name VCC 2 IN1 3 IN2 4 IN3 5 IN4 6 7 GND OUT4 Pin function Power-supply voltage pin. VCC voltage is impressed. The permissible operation voltage is from 4.0 to 16.0(V). The capacitor is connected for stabilization for GND pin (6pin). Motor drive control input pin. Driving control input pin of OUT1 (10pin) and OUT2 (9pin). It combines with IN2 pin (3pin) and it fights desperately. The digital input it, range of the "L" level input is 0 to 0.7(V), range of the "H" level input is from 1.8 to 5.5(V). PWM can be input. Pull-down resistance 100(kΩ) is built into in the pin. It becomes a standby mode because all IN1, IN2, IN3, and IN4 pins are made "L", and the circuit current can be adjusted to 0. Motor drive control input pin. Driving control input pin of OUT1 (10pin) and OUT2 (9pin). It combines with IN1 pin (2pin) and it uses it. PWM can be input. With built-in pull-down resistance. Motor drive control input pin. Driving control input pin of OUT3 (8pin) and OUT4 (7pin). It combines with IN4 pin (5pin) and it uses it. PWM can be input. With built-in pull-down resistance. Motor drive control input pin. Driving control input pin of OUT3 (8pin) and OUT4 (7pin). It combines with IN3 pin (4pin) and it uses it. PWM can be input. With built-in pull-down resistance. Ground pin. Driving output pin. The motor coil is connected between terminal OUT3 (8pin). 8 OUT3 Driving output pin. The motor coil is connected between terminal OUT4 (7pin). 9 OUT2 Driving output pin. The motor coil is connected between terminal OUT1 (10pin). 10 OUT1 Driving output pin. The motor coil is connected between terminal OUT2 (9pin). Equivalent Circuit VCC OUT1 (OUT3) OUT2 (OUT4) Operation explanation 1. DCM output control logic Input IN1 L L H L H IN2 L L L H H IN3 L L H L H IN4 L L L H H OUT1 OFF OFF H L L Output OUT2 OUT3 OFF OFF OFF L H L OFF H L L Remarks OUT4 OFF 1CH OFF L H L 2CH Stand-by Stand-by Forward Reverse Brake Stand-by Forward Reverse Brake No.A1802-4/6 LV8548M 2. About the switch time from the stand-by state to the state of operation When IN1, IN2, IN3, IN4 are "L", this IC has completely stopped operating. After the time of reset of about 4μs of an internal setting, it shifts to a prescribed output status corresponding to the state of the input when the signal enters the input terminal. Reset of about 4μs doesn't hang even if the motor is driven from the stand-by state when either CH drives and the output becomes an output status corresponding to the state of the input. As for full power TR between the reset time, turning off is maintained. 1ch input ON 2ch input ON Input OFF 2ch input ON IN1 OUT1 1ch side forward (Reset time) IN3 OUT3 2ch side forward Stand-by state Stand-by state (Reset time) There is no reset time when another CH drives. 3. Example of current wave type in each excitation mode when stepping motor parallel input is controlled. • 2 phase excitation • 1-2 phase excitation IN1 IN1 IN2 IN2 IN3 IN3 IN4 I1 IN4 (%) 100 I1 0 -100 100 I2 (%) 100 0 -100 100 I2 0 -100 0 -100 Application Circuit Example 1. Example of applied circuit when two DC motor driving C1 6 GND OUT4 8 OUT3 6 GND IN2 IN3 IN4 3 4 5 IN1 IN4 5 2 IN3 4 VCC IN2 3 1 IN1 2 C1 Logic input 9 7 OUT4 VCC LV8548M 1 + OUT2 8 OUT3 OUT1 10 9 LV8548M 7 M M OUT2 OUT1 10 M 2. Example of applied circuit when one stepping motor driving + Logic input No.A1802-5/6 LV8548M 3. Example of applied circuit when connecting it in parallel The use likened to H bridge 1ch is shown possible in the figure below by connecting IN1 with IN3, IN2 with IN4, OUT1 with OUT3, OUT2, and OUT4. (IO max=2.0A, Upper and lower total RON=0.5Ω) 6 GND 7 OUT4 8 OUT3 9 OUT2 OUT1 10 M C1 IN1 IN2 IN3 IN4 2 3 4 5 1 VCC LV8548M + Logic input * Bypass capacitor (C1) connected between VCC-GND of all examples of applied circuit recommends the electric field capacitor of 0.1μA to 10μA. Confirm there is no problem in operation in the state of the motor load including the temperature property about the value of the capacitor. Mount the position where the capacitor is mounted on nearest IC. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2010. Specifications and information herein are subject to change without notice. PS No.A1802-6/6