Numonyx M36W0R6040T1 64 mbit (4 mb ã 16, multiple bank, burst) flash memory and 16 mbit (1 mb ã 16) psram, multi-chip package Datasheet

M36W0R6040T1
M36W0R604BT1
64 Mbit (4 Mb ×16, Multiple Bank, Burst) Flash memory
and 16 Mbit (1 Mb ×16) PSRAM, multi-chip package
Features
■
Multi-chip package
– 1 die of 64 Mbit (4 Mb x 16) Flash memory
– 1 die of 16 Mbit (1 Mb x 16) Pseudo SRAM
■
Supply voltage
– VDDF = VDDP = VDDQ = 1.7 V to 1.95 V
■
Low power consumption
■
Electronic signature
– Manufacturer Code: 20h
– Device Code (top flash configuration),
M36W0R6040T1: 8810h
– Device Code (bottom flash configuration),
M36W0R604BT1: 8811h
■
■
Stacked TFBGA88 (ZAQ)
8 × 10 mm
■
Block locking
– All blocks locked at Power-up
– Any combination of blocks can be locked
– WPF for Block Lock-Down
■
Security
– 128-bit user programmable OTP cells
– 64-bit unique device number
■
Common Flash Interface (CFI)
■
100 000 program/erase cycles per block
ECOPACK® packages available
Flash memory
■
FBGA
Programming time
– 8 µs by Word typical for Fast Factory
Program
– Double/Quadruple Word Program option
– Enhanced Factory Program options
Memory blocks
– Multiple Bank Memory Array: 4 Mbit Banks
– Parameter Blocks (Top or Bottom location)
■
Synchronous / Asynchronous Read
– Synchronous Burst Read mode: 66 MHz
– Asynchronous/ Synchronous Page Read
mode
– Random Access: 70 ns
■
Dual operations
– Program Erase in one Bank while Read in
others
– No delay between Read and Write
operations
November 2007
PSRAM
■
Access time: 70 ns
■
Low standby current: 110 µA
■
Deep power down current: 10 µA
Rev 0.3
1/22
www.numonyx.com
1
Contents
M36W0R6040T1, M36W0R604BT1
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1
Address Inputs (A0-A19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2
Address Inputs (A20-A21) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3
Data Input/Output (DQ0-DQ15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4
Flash Chip Enable (EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5
Flash Output Enable (GF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6
Flash Write Enable (WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.7
Flash Write Protect (WPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.8
Flash Reset (RPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.9
Flash Latch Enable (LF
2.10
Flash Clock (KF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.11
Flash Wait (WAITF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.12
PSRAM Chip Enable (E1P
2.13
PSRAM Chip Enable (E2P) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.14
PSRAM Output Enable (GP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.15
PSRAM Write Enable (WP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.16
PSRAM Upper Byte Enable (UBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.17
PSRAM Lower Byte Enable (LBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.18
VDDF supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.19
VDDP supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.20
VDDQ supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.21
VPPF program supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.22
VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2/22
M36W0R6040T1, M36W0R604BT1
Contents
6
Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3/22
List of tables
M36W0R6040T1, M36W0R604BT1
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
4/22
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Main operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Device capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Stacked TFBGA88 8 × 10 mm - 8 × 10 ball array, 0.8 mm pitch, package
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
M36W0R6040T1, M36W0R604BT1
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TFBGA connections (top view through package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Stacked TFBGA88 8 × 10 mm - 8 × 10 active ball array, 0.8 mm pitch, package outline. . 19
5/22
Description
1
M36W0R6040T1, M36W0R604BT1
Description
The M36W0R6040T1 and M36W0R604BT1 combine two memory devices in a multi-chip
package:
●
a 64-Mbit, Multiple Bank Flash memories, the M58WR064HT/B
●
a 16-Mbit Pseudo SRAM, the M69AR024B. Recommended operating conditions do not
allow more than one memory to be active at the same time.
The purpose of this document is to describe how the two memory components operate with
respect to each other. It must be read in conjunction with the M58WR064HTB and
M69AR024B datasheets, where all specifications required to operate the Flash memory and
PSRAM components are fully detailed.
The memory is offered in a Stacked TFBGA88 (8 × 10 mm, 8 × 10 ball array, 0.8 mm pitch)
package.
In order to meet environmental requirements, Numonyx offers the M36W0R6040T1 and
M36W0R604BT1 in ECOPACK® packages. These packages have a Lead-free second-level
interconnect. The category of Second-Level Interconnect is marked on the package and on
the inner box label, in compliance with JEDEC Standard JESD97.
The maximum ratings related to soldering conditions are also marked on the inner box label.
The memory is supplied with all the bits erased (set to ‘1’).
6/22
M36W0R6040T1, M36W0R604BT1
Figure 1.
Description
Logic diagram
VDDQ
VPPF
VDDP
VDDF
22
16
A0-A21
DQ0-DQ15
EF
GF
WAITF
WF
RPF
WPF
LF
KF
M36W0R6040T1
M36W0R6040B1
E1P
GP
WP
E2P
UBP
LBP
VSS
Ai11080b
7/22
Description
M36W0R6040T1, M36W0R604BT1
Table 1.
Signal names
A0-A19
Common Address Inputs
DQ0-DQ15
Common Data Input/Output
VDDF
Flash Memory Power Supply
VDDQ
Common Flash and PSRAM Power Supply for I/O Buffers
VPPF
Common Flash Optional Supply Voltage for Fast Program & Erase
VSS
Ground
VDDP
PSRAM Power Supply
NC
Not Connected Internally
DU
Do Not Use as Internally Connected
Flash memory control functions
A21-A20
Address Inputs for the Flash memory only
LF
Latch Enable input
EF
Chip Enable input
GF
Output Enable input
WF
Write Enable input
RPF
Reset input
WPF
Write Protect input
KF
Burst Clock
WAITF
Wait Data in Burst Mode
PSRAM control functions
8/22
E1P
Chip Enable input
GP
Output Enable input
WP
Write Enable input
E2P
Power-down input
UBP
Upper Byte Enable input
LBP
Lower Byte Enable input
M36W0R6040T1, M36W0R604BT1
Figure 2.
Description
TFBGA connections (top view through package)
1
2
3
4
5
A
DU
DU
B
A4
A18
A19
VSS
VDDF
C
A5
LBP
NC
VSS
D
A3
A17
NC
E
A2
A7
F
A1
G
6
7
8
DU
DU
NC
A21
A11
NC
KF
NC
A12
VPPF
WP
EP
A9
A13
NC
WPF
LF
A20
A10
A15
A6
UBP
RPF
WF
A8
A14
A16
A0
DQ8
DQ2
DQ10
DQ5
DQ13
WAITF
NC
H
GP
DQ0
DQ1
DQ3
DQ12
DQ14
DQ7
NC
J
NC
GF
DQ9
DQ11
DQ4
DQ6
DQ15
VDDQ
K
EF
NC
NC
NC
VDDP
NC
VDDQ
E2P
L
VSS
VSS
VDDQ
VDDF
VSS
VSS
VSS
VSS
M
DU
DU
DU
DU
AI08525
9/22
Signal descriptions
2
M36W0R6040T1, M36W0R604BT1
Signal descriptions
See Figure 1: Logic diagram and Table 1: Signal names, for a brief overview of the signals
connect-ed to this device.
2.1
Address Inputs (A0-A19)
Addresses A0-A19 are common inputs for the Flash Memory and PSRAM components. The
Address Inputs select the cells in the memory array to access during Bus Read operations.
During Bus Write operations they control the commands sent to the Command Interface of
the Flash memory Program/Erase Controller, and they select the cells to access in the
PSRAM.
The Flash memory is accessed through the Chip Enable signal (EF) and through the Write
Enable (WF) signal, while the PSRAM is accessed through two Chip Enable signals (E1P
and E2P) and the Write Enable signal (WP).
2.2
Address Inputs (A20-A21)
Addresses A20-A21 are inputs for the Flash memory component only. The Flash memory is
accessed through the Chip Enable signals (EF) and through the Write Enable (WF) signal.
2.3
Data Input/Output (DQ0-DQ15)
For the Flash memory, the Data I/O outputs the data stored at the selected address during a
Bus Read operation or inputs a command or the data to be programmed during a Write Bus
operation.
For the PSRAM, the Upper Byte Data Inputs/Outputs carry the data to or from the upper
part of the selected address during a Write or Read operation, when Upper Byte Enable
(UBP) is driven Low.
Likewise, the Lower Byte Data Inputs/Outputs carry the data to or from the lower part of the
selected address during a Write or Read operation, when Lower Byte Enable (LBP) is driven
Low.
2.4
Flash Chip Enable (EF)
The Chip Enable inputs activate the memory control logics, input buffers, decoders and
sense amplifiers. When Chip Enable is Low, VIL, and Reset is High, VIH, the device is in
active mode. When Chip Enable is at VIH the Flash memory is deselected, the outputs are
high impedance and the power consumption is reduced to the standby level.
2.5
Flash Output Enable (GF)
The Output Enable pins control data outputs during Flash memory Bus Read operations.
10/22
M36W0R6040T1, M36W0R604BT1
2.6
Signal descriptions
Flash Write Enable (WF)
The Write Enable controls the Bus Write operation of the Flash memories’ Command
Interface. The data and address inputs are latched on the rising edge of Chip Enable or
Write Enable whichever occurs first.
2.7
Flash Write Protect (WPF)
Write Protect is an input that gives an additional hardware protection for each block. When
Write Protect is Low, VIL, Lock-Down is enabled and the protection status of the LockedDown blocks cannot be changed. When Write Protect is at High, VIH, Lock-Down is disabled
and the Locked-Down blocks can be locked or unlocked. (Refer to Lock Status Table in
M58WR064HT/B datasheet).
2.8
Flash Reset (RPF)
The Reset input provides a hardware reset of the memory. When Reset is at VIL, the
memory is in Reset mode: the outputs are high impedance and the current consumption is
reduced to the Reset Supply Current IDD2. Refer to the M58WR064HT/B datasheet, for the
value of IDD2. After Reset all blocks are in the Locked state and the Configuration Register is
reset. When Reset is at VIH, the device is in normal operation. Exiting Reset mode the
device enters Asynchronous Read mode, but a negative transition of Chip Enable or Latch
Enable is required to ensure valid data outputs.
The Reset pin can be interfaced with 3V logic without any additional circuitry. It can be tied
to VRPH (refer to the M58WR064HT/B datasheet).
2.9
Flash Latch Enable (LF
Latch Enable latches the address bits on its rising edge. The address latch is transparent
when Latch Enable is Low, VIL, and it is inhibited when Latch Enable is High, VIH. Latch
Enable can be kept Low (also at board level) when the Latch Enable function is not required
or supported.
2.10
Flash Clock (KF)
The Clock input synchronizes the Flash memory to the microcontroller during synchronous
read operations; the address is latched on a Clock edge (rising or falling, according to the
configuration settings) when Latch Enable is at VIL. Clock is don't care during Asynchronous
Read and in write operations.
2.11
Flash Wait (WAITF)
WAIT is a Flash output signal used during Synchronous Read to indicate whether the data
on the output bus are valid. This output is high impedance when Flash Chip Enable is at VIH
or Flash Reset is at VIL. It can be configured to be active during the wait cycle or one clock
cycle in advance. The WAITF signal is not gated by Output Enable.
11/22
Signal descriptions
2.12
M36W0R6040T1, M36W0R604BT1
PSRAM Chip Enable (E1P
When asserted (Low), the Chip Enable, E1P, activates the memory state machine, address
buffers and decoders, allowing Read and Write operations to be performed. When deasserted (High), all other pins are ignored, and the device is put, automatically, in low-power
Standby mode.
2.13
PSRAM Chip Enable (E2P)
The Chip Enable, E2P, puts the device in Deep Power-down mode when it is driven Low.
This is the lowest power mode.
2.14
PSRAM Output Enable (GP)
The Output Enable, GP, provides a high speed tri-state control, allowing fast read/write
cycles to be achieved with the common I/O data bus.
2.15
PSRAM Write Enable (WP)
The Write Enable, WP, controls the Bus Write operation of the memory.
2.16
PSRAM Upper Byte Enable (UBP)
The Upper Byte Enable, UBP, gates the data on the Upper Byte Data Inputs/Outputs (DQ8DQ15) to or from the upper part of the selected address during a Write or Read operation.
2.17
PSRAM Lower Byte Enable (LBP)
The Lower Byte Enable, LBP, gates the data on the Lower Byte Data Inputs/Outputs (DQ0DQ7) to or from the lower part of the selected address during a Write or Read operation.
2.18
VDDF supply voltage
VDDF provides the power supply to the internal core of the Flash memory component. It is
the main power supplies for all Flash memory operations (Read, Program and Erase).
2.19
VDDP supply voltage
The VDDP Supply Voltage supplies the power for all operations (Read or Write) and for
driving the refresh logic, even when the device is not being accessed.
12/22
M36W0R6040T1, M36W0R604BT1
2.20
Signal descriptions
VDDQ supply voltage
VDDQ provides the power supply for the Flash Memory and PSRAM I/O pins. This allows all
Outputs to be powered independently of the Flash Memory and PSRAM core power
supplies: VDDF and VDDP, respectively.
2.21
VPPF program supply voltage
VPPF is both a Flash Memory control input and a Flash Memory power supply pin. The two
functions are selected by the voltage range applied to the pin.
If VPPF is kept in a low voltage range (0V to VDDQ) VPPF is seen as a control input. In this
case a voltage lower than VPPLKF gives an absolute protection against Program or Erase,
while VPPF > VPP1F enables these functions (see the M58WR064HT/B datasheet for the
relevant values). VPPF is only sampled at the beginning of a Program or Erase; a change in
its value after the operation has started does not have any effect and Program or Erase
operations continue.
If VPPF is in the range of VPPHF it acts as a power supply pin. In this condition VPPF must be
stable until the Program/Erase algorithm is completed.
2.22
VSS ground
VSS is the common ground reference for all voltage measurements in the Flash (core and
I/O Buffers) and PSRAM chips.
Note:
Each Flash memory device in a system should have its supply voltage (VDDF) and the
program supply voltage VPPF decoupled with a 0.1µF ceramic capacitor close to the pin
(high frequency, inherently low inductance capacitors should be as close as possible to the
package). See Figure 5: AC measurement load circuit. The PCB track widths should be
sufficient to carry the required VPPF program and erase currents.
13/22
Functional description
3
M36W0R6040T1, M36W0R604BT1
Functional description
The Flash memory and PSRAM components have separate power supplies but share the
same grounds. They are distinguished by three Chip Enable inputs: EF for the Flash
memory and E1P and E2P for the PSRAM.
Recommended operating conditions do not allow more than one device to be active at a
time. The most common example is simultaneous read operations on the Flash memory and
the PSRAM which would result in a data bus contention. Therefore it is recommended to put
the other devices in the high impedance state when reading the selected device.
Figure 3.
Functional block diagram
VDDF
VPPF
VDDQ
A20-A21
EF
64 Mbit
Flash
Memory
GF
WF
WAITF
LF
KF
RPF
A0-A19
WPF
DQ0-DQ15
VDDP
E1P
GP
WP
16 Mbit
PSRAM
E2P
UBP
LBP
VSS
14/22
AI08449
M36W0R6040T1, M36W0R604BT1
Table 2.
Functional description
Main operating modes(1)
Operation
EF
GP
WP
LF
RPF WAITF(2) E1P E2P
(3)
VIH
GP
WP
UBP LBP
DQ15-DQ0
Flash Read
VIL
VIL
VIH
VIL
Flash Write
VIL
VIH
VIL
VIL(3)
VIH
Flash Address
Latch
VIL
X
VIH
VIL
VIH
Flash Data Out
or Hi-Z(4)
Flash Output
Disable
VIL
X
VIH
Flash Hi-Z
Flash Standby
VIH
X
X
X
VIH
Hi-Z
X
X
X
X
VIL
Hi-Z
Flash Reset
VIH VIH
Flash Data Out
Flash Data In
PSRAM must be disabled
Any PSRAM mode is allowed
Flash Hi-Z
Flash Hi-Z
VIL
VIH
VIL
VIH
VIL
VIL
PSRAM data out
PSRAM Write
VIL
VIH
VIH
VIL
VIL
VIL
PSRAM data in
Output Disable
VIL
VIH
VIH
VIH
X
X
PSRAM Hi-Z
VIH
VIH
X
X
X
X
PSRAM Hi-Z
X
VIL
X
X
X
X
PSRAM Hi-Z
PSRAM Read
Flash Memory must be disabled
PSRAM Standby
PSRAM Deep
Power-Down
Any Flash mode is allowed.
1. X = Don't care.
2. WAIT signal polarity is configured using the Set Configuration Register command. Refer to M58WR064HT/B datasheet for
details.
3. LF can be tied to VIH if the valid address has been previously latched.
4. Depends on GF.
15/22
Maximum rating
4
M36W0R6040T1, M36W0R604BT1
Maximum rating
Stressing the device above the rating listed in the Absolute Maximum Ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the Numonyx SURE Program
and other relevant quality documents.
Table 3.
Absolute maximum ratings
Value
Symbol
Unit
Min
Max
Ambient Operating Temperature
–30
85
°C
TBIAS
Temperature Under Bias
–40
125
°C
TSTG
Storage Temperature
–65
155
°C
Input or Output Voltage
–0.5
VDDQ+0.6
V
VDDF
Flash Memory Core Supply Voltage
–0.2
2.45
V
VDDQ
Input/Output Supply Voltage
–0.2
2.45
V
VDDP
PSRAM Supply Voltage
–0.2
3.3
V
VPPF
Flash Memory Program Voltage
–0.2
14
V
Output Short Circuit Current
100
mA
Time for VPPF at VPPFH
100
hours
TA
VIO
IO
tVPPFH
16/22
Parameter
M36W0R6040T1, M36W0R604BT1
5
DC and AC parameters
DC and AC parameters
This section summarizes the operating measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristics Tables that
follow, are derived from tests performed under the Measurement Conditions summarized in
<Blue>Table 4., Operating and AC measurement conditions. Designers should check that
the operating conditions in their circuit match the operating conditions when relying on the
quoted parameters.
Table 4.
Operating and AC measurement conditions
Flash memory
PSRAM
Parameter
Unit
Min
Max
Min
Max
VDDF Supply Voltage
1.7
1.95
–
–
V
VDDP Supply Voltage
–
–
1.7
1.95
V
VDDQ Supply Voltage
1.7
1.95
–
–
V
VPPF Supply Voltage (Factory environment)
11.4
12.6
–
–
V
VPPF Supply Voltage (Application environment)
–0.4
VDDQ +0.4
–
–
V
Ambient Operating Temperature
–40
85
–30
85
°C
Load Capacitance (CL)
30
Input Rise and Fall Times
5
Input Pulse Voltages
Input and Output Timing Ref. Voltages
Figure 4.
50
pF
ns
0 to VDDQ
0 to VDDP
V
VDDQ/2
VDDP/2
V
AC measurement I/O waveform
VDDQ
VDDQ/2
0V
AI06161
17/22
DC and AC parameters
Figure 5.
M36W0R6040T1, M36W0R604BT1
AC measurement load circuit
VDDQ
VDDF
VDDQ
16.7kΩ
DEVICE
UNDER
TEST
CL
0.1µF
16.7kΩ
0.1µF
CL includes JIG capacitance
AI08364
Table 5.
Symbol
CIN
COUT
Device capacitance(1)
Parameter
Input Capacitance
Output Capacitance
Test condition
Min
Max
Unit
VIN = 0V
12
pF
VOUT = 0V
15
pF
1. Sampled only, not 100% tested.
Please refer to the M58WR064HT/B and M69AR024B datasheets for further DC and AC
characteristics values and illustrations.
18/22
M36W0R6040T1, M36W0R604BT1
6
Package mechanical
Package mechanical
Figure 6.
Stacked TFBGA88 8 × 10 mm - 8 × 10 active ball array, 0.8 mm pitch,
package outline
D
D1
e
SE
E
E2
E1
b
BALL "A1"
ddd
FE
FE1
FD
SD
A2
A
A1
BGA-Z42
1. Drawing is not to scale.
Table 6.
Stacked TFBGA88 8 × 10 mm - 8 × 10 ball array, 0.8 mm pitch, package
mechanical data
millimeters
inches
Symbol
Typ
Min
A
Max
Typ
Min
1.200
A1
Max
0.0472
0.200
0.0079
A2
0.850
0.0335
b
0.350
0.300
0.400
0.0138
0.0118
0.0157
D
8.000
7.900
8.100
0.3150
0.3110
0.3189
D1
5.600
0.2205
ddd
0.100
9.900
E
10.000
E1
7.200
0.2835
E2
8.800
0.3465
e
0.800
FD
1.200
0.0472
FE
1.400
0.0551
FE1
0.600
0.0236
SD
0.400
0.0157
SE
0.400
0.0157
–
10.100
0.0039
–
0.3937
0.0315
0.3898
0.3976
–
–
19/22
Part numbering
7
M36W0R6040T1, M36W0R604BT1
Part numbering
Table 7.
Ordering information scheme
Example:
M36 W 0 R 6 0 4 0 T 1
ZAQ E
Device type
M36 = Multi-chip package (Multiple Flash + RAM)
Flash 1 architecture
W = Multiple Bank, Burst mode
Flash 2 architecture
0 = none present
Operating voltage
R = VDDF = VDDQ =VDDP = 1.7 V to 1.95 V
Flash 1 density
6 = 64 Mbit
Flash 2 density
0 = none present
RAM 1 density
4 = 16 Mbit
RAM 0 density
0 = none present
Parameter blocks location
T = Top Boot Block Flash
B = Bottom Boot Block Flash
Product version
1 = 90 nm Flash technology, 70 ns;
0.18 µm RAM, 70 ns speed
Package
ZAQ = Stacked TFBGA88 8 × 10 mm - 8 × 10 active ball array, 0.8 mm pitch
Option
E = ECOPACK® Package, Standard Packing
F = ECOPACK® Package, Tape & Reel Packing
Devices are shipped from the factory with the memory content bits erased to ’1’. For a list of
available options (Speed, Package, etc.) or for further information on any aspect of this
device, please contact the Numonyx Sales Office nearest to you.
20/22
M36W0R6040T1, M36W0R604BT1
8
Revision history
Revision history
Table 8.
Document revision history
Date
Version
Revision Details
08-June-2005
0.1
First Issue.
18-Jan-2007
0.2
Document status promoted from Target Specification to full
Datasheet.
Package is ECOPACK® compliant.
DC characteristics of Flash memory and PSRAM components
removed (for further details please refer to the M58WR064HT/B
and M69AR024B datasheets. Small text changes.
14-Nov-2007
0.3
Applied Numonyx branding.
21/22
M36W0R6040T1, M36W0R604BT1
Please Read Carefully:
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX™ PRODUCTS. NO LICENSE, EXPRESS OR
IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT
AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY
WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF
NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility
applications.
Numonyx may make changes to specifications and product descriptions at any time, without notice.
Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the
presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied,
by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves
these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by
visiting Numonyx's website at http://www.numonyx.com.
Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 11/5/7, Numonyx, B.V., All Rights Reserved.
22/22
Similar pages