Unictron H2U34WGTQW0100 3.2x1.6x0.5 wifi/bluetooth ceramic chip antenna (aa055) Datasheet

3.2 x 1.6 x 0.5 WiFi/Bluetooth Ceramic Chip Antenna (AA055)
1.
Explanation of Product Number
H
2
U
3
4
W
(1)
G
T
(2)
Q
W
(3)
0
1
0
0
(4)
Product Code:
(1) Product Categories:
4: ceramic substrate chip antenna
(2) Dimensions and Polarization:
WG: 3.2x1.6x0.5(mm) / linear polarization
(3) Material / Working Frequency / Ground Plane Dimensions:
TQW: AS 6 / 2400~2500MHz / 80 x 40(mm)
(4) Antenna Series:
01: serial number
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
1
OF
F
11
2.
Features
*Stable and reliable in performances
*Low temperature coefficient of frequency
*Low profile, compact size
*RoHS compliance
*SMT processes compatible
3.
Applications
*Bluetooth earphone systems
*Hand-held devices when Bluetooth/WiFi functions are needed, e.g., Smart phone.
*IEEE802.11 b/g/n
*ZigBee
*Wireless PCMCIA cards or USB dongle
4.
Description
Unictron’s chip antenna series are specially designed for Bluetooth/WiFi applications.
Based on Unictron’s proprietary design and processes, this chip antenna has
excellent stability and sensitivity to consistently provide high signal reception
efficiency.
5.
Electrical Specifications (80x40(mm) ground plane)
5-1.
Characteristics
Outline Dimensions
Ground Plane
Center Frequency*
Bandwidth (under -10dB return loss)
VSWR
Impedance
Polarization
Gain**
Specifications
Unit
3.2x1.6x0.5
80x40
2442
100 min.
2 max.
50
Linear Polarization
mm
mm
MHz
MHz
2.5 (typical)
dBi
84 (typical)
0±20 max
(@ -40℃~85℃)
%
Peak
Efficiency
Temperature Coefficient
of Frequency
Ω
ppm/℃
*Center frequency will be offset to working frequency according to the conditions of user’s ground plane and radome.
**The data was measured by A Test Lab Techno Corp.(CTIA Authorized Test Lab).
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
2
OF
F
11
5-2.
Return Loss(S11)
6.
VSWR
Antenna Dimensions & Test Board (unit: mm)
a. Antenna Dimensions
Feed Side
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
3
OF
F
11
b. Test Board with Antenna
Unit : mm
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
4
OF
F
11
7.
Radiation Pattern (80x40(mm) ground plane)
7-1. 3D Gain Pattern (at 2442 MHz)
Z
X
Y
Y
X
Z
Z
X
Y
X
Y
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
5
OF
F
11
7-2. Efficiency Table
Frequency(MHz)
2400 2410 2420 2430 2442 2450 2460 2470 2480 2490 2500
Efficiency(dB)
-1.38 -1.04 -0.85 -0.74 -0.73 -0.76 -0.86 -1.05 -1.18 -1.27 -1.40
Efficiency(%)
72.83 78.71 82.27 84.39 84.53 84.04 82.00 78.60 76.14 74.64 72.50
Gain(dBi)
1.47
1.81
2.10
2.40
2.50
2.50
2.37
2.10
1.90
1.87
1.75
7-3. Efficiency vs. Frequency
Efficiency vs. Frequency
100.00
Efficiency(%)
90.00
80.00
70.00
60.00
50.00
2400
2410
2420
2430
2442
2450
2460
2470
2480
2490
2500
Frequency(MHz)
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
6
OF
F
11
8.
Layout Guide:
a. Solder Land Pattern:
Land pattern for soldering (gray marking areas) is as shown below. Depending on
Customer’s requirement, matching circuit as shown below is also recommended .
Top View
Back View
Unit:mm
9.
Frequency tuning:
a. Chip antenna tuning scenario:
Feed
Fine tuning element
Matching circuit
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
7
OF
F
11
b. Matching circuit:(Center frequency is about 2442MHz at 80x40(mm) ground plane)
System Matching Circuit Component
Location
Description
Vendor
1
N/A
-
2
0Ω
(0402)
3
N/A
-
4
Fine tuning
element
22pF
TDK(0402)
8pF
TDK(0402)
c. Fine tuning element vs. Center frequency
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
8
OF
F
11
10. Reliability test:
Test item
Test condition / Test method
Specification
Solderability
*Solder bath temperature:260 ± 5°C
*Immersion time:2 ± 0.5 sec
At least 95% of a surface of each
terminal electrode must be covered by
fresh solder.
Resistance to dissolution
of metallization)
*Solder bath temperature:260 ± 5°C
*Leaching immersion time:30 ± 0.5 sec
Loss of metallization on the edges of
each electrode shall not exceed 25%.
Drop Test
*1.8m drop on concrete with 150g
weight
*XYZ each 30 times
No mechanical damage.
Samples shall satisfy electrical
specification after test.
Bending test
Warp:2mm
No mechanical damage.
Samples shall satisfy electrical
specification after test.
Temperature cycle
-55°C/ 30min~125°C /30min
Total 1000 cycles
No mechanical damage.
Samples shall satisfy electrical
specification after test
High temperature
*Temperature:125°C
*Test duration:1000 hours
No mechanical damage.
Samples shall satisfy electrical
specification after test.
Low temperature
*Temperature:-55°C
*Test duration:1000 hours
No mechanical damage.
Samples shall satisfy electrical
specification after test.
Adhesive Strength of
Termination
*Pressure:5N
*Duration:10±1 sec
No remarkable damage or removal of
the termination.
Vibration
*Applied Frequency:10-55-10Hz(1min)
*1.5 p-p amplitude for XYZ each
direction of 120min
No mechanical damage.
Samples shall satisfy electrical
specification after test
Damp heat
*Humidity:85%
*Temperature:85°C
*Time:1000 hours
No mechanical damage.
Samples shall satisfy electrical
specification after test
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
9
OF
F
11
11. Soldering Conditions:
a. Typical Soldering Profile for Lead-free Process
20-40s
260°C
Temterature (°C)
217°C
150-200°C
Pre-heating
60-150s
60-180s
Time (s.)
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
10
OF
F
11
12.
Packing:
(1) Quantity/Reel: 6000pcs/Reel
(2) Plastic tape:
2.1 Tape Dimensions(unit: mm)
Feature
Specifications Tolerances
W
12.00
±0.30
P
8.00
±0.10
E
1.75
±0.10
F
5.50
±0.10
P2
2.00
±0.10
D
1.50
+0.10
-0.00
Po
4.00
±0.10
10Po
40.00
±0.20
1. Cumulative tolerance of 10 sprocket hole pitch: ±0.20mm
2. Carrier camber not to exceed 1mm in 250mm
3. Ao and Bo measured on a plane above the inside bottom
of the pocket.
4. Ko measured from a plane on the inside bottom of the
pocket to the top surface of the carrier.
5. All dimensions meet EIA-481-B requirements.
6. Material: □ Clear Non Anti-Static Polystyrene.
■ Black Conductive Polystyrene.
2.2 Pocket Dimensions(unit: mm)
Feature Specifications Tolerances
Ao
1.90
+0.20
-0.10
Bo
3.50
Ko
0.60
±0.10
t
0.30
±0.05
13. Storage Conditions:
(1) Temperature: -25℃ to 85℃
(2) Relative Humidity: 20% to 70%
Tolerances (Unless otherwise specified)
X: ± 1
X.X : ± 0.1
X.XX : ± 0.01
Angle : ±
Hole Dia. : ±
Scale :
Unit:mm
Prepared By : Meiping
Checked By :Chinling
Designed By : Andrew
Approved By :Herbert
TITLE: 3.2x1.6x0.5 WiFi/Bluetooth Ceramic
Chip Antenna (AA055)
Unictron Technologies Corporation
Website: www.unictron.com
THIS SPECIFICATION IS THE PROPERTY OF UNICTRON
TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED
OR USED IN ALL CIRCUMSTANCES WITHOUT WRITTEN PERMISSION
DOCUMENT
NO.
REV.
H2U34WGTQW0100
PAGE
11
OF
F
11
Similar pages